| bb985070 | 19-Dec-2024 |
Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> |
scsi: ufs: core: Honor runtime/system PM levels if set by host controller drivers
Otherwise, the default levels will override the levels set by the host
controller drivers.
Signed-off-by: Manivanna
scsi: ufs: core: Honor runtime/system PM levels if set by host controller drivers
Otherwise, the default levels will override the levels set by the host
controller drivers.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20241219-ufs-qcom-suspend-fix-v3-2-63c4b95a70b9@linaro.org
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
show more ...
|
| 7bac6568 | 19-Dec-2024 |
Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> |
scsi: ufs: qcom: Power off the PHY if it was already powered on in ufs_qcom_power_up_sequence()
PHY might already be powered on during ufs_qcom_power_up_sequence() in a
couple of cases:
1. During
scsi: ufs: qcom: Power off the PHY if it was already powered on in ufs_qcom_power_up_sequence()
PHY might already be powered on during ufs_qcom_power_up_sequence() in a
couple of cases:
1. During UFSHCD_QUIRK_REINIT_AFTER_MAX_GEAR_SWITCH quirk
2. Resuming from spm_lvl = 5 suspend
In those cases, it is necessary to call phy_power_off() and phy_exit() in
ufs_qcom_power_up_sequence() function to power off the PHY before calling
phy_init() and phy_power_on().
Case (1) is doing it via ufs_qcom_reinit_notify() callback, but case (2) is
not handled. So to satisfy both cases, call phy_power_off() and phy_exit()
if the phy_count is non-zero. And with this change, the reinit_notify()
callback is no longer needed.
This fixes the below UFS resume failure with spm_lvl = 5:
ufshcd-qcom 1d84000.ufshc: Enabling the controller failed
ufshcd-qcom 1d84000.ufshc: Enabling the controller failed
ufshcd-qcom 1d84000.ufshc: Enabling the controller failed
ufshcd-qcom 1d84000.ufshc: ufshcd_host_reset_and_restore: Host init failed -5
ufshcd-qcom 1d84000.ufshc: Enabling the controller failed
ufshcd-qcom 1d84000.ufshc: Enabling the controller failed
ufshcd-qcom 1d84000.ufshc: Enabling the controller failed
ufshcd-qcom 1d84000.ufshc: ufshcd_host_reset_and_restore: Host init failed -5
ufshcd-qcom 1d84000.ufshc: Enabling the controller failed
ufshcd-qcom 1d84000.ufshc: Enabling the controller failed
ufshcd-qcom 1d84000.ufshc: Enabling the controller failed
ufshcd-qcom 1d84000.ufshc: ufshcd_host_reset_and_restore: Host init failed -5
ufshcd-qcom 1d84000.ufshc: Enabling the controller failed
ufshcd-qcom 1d84000.ufshc: Enabling the controller failed
ufshcd-qcom 1d84000.ufshc: Enabling the controller failed
ufshcd-qcom 1d84000.ufshc: ufshcd_host_reset_and_restore: Host init failed -5
ufshcd-qcom 1d84000.ufshc: Enabling the controller failed
ufshcd-qcom 1d84000.ufshc: Enabling the controller failed
ufshcd-qcom 1d84000.ufshc: Enabling the controller failed
ufshcd-qcom 1d84000.ufshc: ufshcd_host_reset_and_restore: Host init failed -5
ufs_device_wlun 0:0:0:49488: ufshcd_wl_resume failed: -5
ufs_device_wlun 0:0:0:49488: PM: dpm_run_callback(): scsi_bus_resume returns -5
ufs_device_wlun 0:0:0:49488: PM: failed to resume async: error -5
Cc: stable@vger.kernel.org # 6.3
Fixes: baf5ddac90dc ("scsi: ufs: ufs-qcom: Add support for reinitializing the UFS device")
Reported-by: Ram Kumar Dwivedi <quic_rdwivedi@quicinc.com>
Tested-by: Amit Pundir <amit.pundir@linaro.org> # on SM8550-HDK
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20241219-ufs-qcom-suspend-fix-v3-1-63c4b95a70b9@linaro.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
show more ...
|
| f103396a | 06-Dec-2024 |
liuderong <liuderong@oppo.com> |
scsi: ufs: core: Update compl_time_stamp_local_clock after completing a cqe
lrbp->compl_time_stamp_local_clock is set to zero after sending a sqe
but it is not updated after completing a cqe. Thus
scsi: ufs: core: Update compl_time_stamp_local_clock after completing a cqe
lrbp->compl_time_stamp_local_clock is set to zero after sending a sqe
but it is not updated after completing a cqe. Thus the printed
information in ufshcd_print_tr() will always be zero.
Update lrbp->cmpl_time_stamp_local_clock after completing a cqe.
Log sample:
ufshcd-qcom 1d84000.ufshc: UPIU[8] - issue time 8750227249 us
ufshcd-qcom 1d84000.ufshc: UPIU[8] - complete time 0 us
Fixes: c30d8d010b5e ("scsi: ufs: core: Prepare for completion in MCQ")
Reviewed-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Peter Wang <peter.wang@mediatek.com>
Signed-off-by: liuderong <liuderong@oppo.com>
Link: https://lore.kernel.org/r/1733470182-220841-1-git-send-email-liuderong@oppo.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
show more ...
|
| 7f45ed5f | 22-Nov-2024 |
Peter Wang <peter.wang@mediatek.com> |
scsi: ufs: core: Add missing post notify for power mode change
When the power mode change is successful but the power mode hasn't
actually changed, the post notification was missed. Similar to the
scsi: ufs: core: Add missing post notify for power mode change
When the power mode change is successful but the power mode hasn't
actually changed, the post notification was missed. Similar to the
approach with hibernate/clock scale/hce enable, having pre/post
notifications in the same function will make it easier to maintain.
Additionally, supplement the description of power parameters for the
pwr_change_notify callback.
Fixes: 7eb584db73be ("ufs: refactor configuring power mode")
Cc: stable@vger.kernel.org #6.11.x
Signed-off-by: Peter Wang <peter.wang@mediatek.com>
Link: https://lore.kernel.org/r/20241122024943.30589-1-peter.wang@mediatek.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
show more ...
|
| 019880c0 | 21-Nov-2024 |
Martin K. Petersen <martin.petersen@oracle.com> |
Merge patch series "scsi: ufs: Bug fixes for ufs core and platform drivers"
Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> says:
Hi,
This series has several bug fixes that I encountered
Merge patch series "scsi: ufs: Bug fixes for ufs core and platform drivers"
Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> says:
Hi,
This series has several bug fixes that I encountered when the ufs-qcom driver
was removed and inserted back. But the fixes are applicable to other platform
glue drivers as well.
This series is tested on Qcom RB5 development board based on SM8250 SoC.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20241111-ufs_bug_fix-v1-0-45ad8b62f02e@linaro.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
show more ...
|
| 1695c436 | 11-Nov-2024 |
Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> |
scsi: ufs: core: Cancel RTC work during ufshcd_remove()
Currently, RTC work is only cancelled during __ufshcd_wl_suspend(). When
ufshcd is removed in ufshcd_remove(), RTC work is not cancelled. Due
scsi: ufs: core: Cancel RTC work during ufshcd_remove()
Currently, RTC work is only cancelled during __ufshcd_wl_suspend(). When
ufshcd is removed in ufshcd_remove(), RTC work is not cancelled. Due to
this, any further trigger of the RTC work after ufshcd_remove() would
result in a NULL pointer dereference as below:
Unable to handle kernel NULL pointer dereference at virtual address 00000000000002a4
Workqueue: events ufshcd_rtc_work
Call trace:
_raw_spin_lock_irqsave+0x34/0x8c
pm_runtime_get_if_active+0x24/0xb4
ufshcd_rtc_work+0x124/0x19c
process_scheduled_works+0x18c/0x2d8
worker_thread+0x144/0x280
kthread+0x11c/0x128
ret_from_fork+0x10/0x20
Since RTC work accesses the ufshcd internal structures, it should be cancelled
when ufshcd is removed. So do that in ufshcd_remove(), as per the order in
ufshcd_init().
Cc: stable@vger.kernel.org # 6.8
Fixes: 6bf999e0eb41 ("scsi: ufs: core: Add UFS RTC support")
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20241111-ufs_bug_fix-v1-1-45ad8b62f02e@linaro.org
Reviewed-by: Peter Wang <peter.wang@mediatek.com>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
show more ...
|
| 60b4dd14 | 19-Nov-2024 |
Ziqi Chen <quic_ziqichen@quicinc.com> |
scsi: ufs: core: Add ufshcd_send_bsg_uic_cmd() for UFS BSG
User layer applications can send UIC GET/SET commands via the BSG
framework, and if the user layer application sends a UIC SET command to t
scsi: ufs: core: Add ufshcd_send_bsg_uic_cmd() for UFS BSG
User layer applications can send UIC GET/SET commands via the BSG
framework, and if the user layer application sends a UIC SET command to the
PA_PWRMODE attribute, a power mode change shall be initiated in UniPro and
two interrupts shall be triggered if the power mode is successfully
changed, i.e., UIC Command Completion interrupt and UIC Power Mode
interrupt.
The current UFS BSG code calls ufshcd_send_uic_cmd() directly, with which
the second interrupt, i.e., UIC Power Mode interrupt, shall be treated as
unhandled interrupt. In addition, after the UIC command is completed, user
layer application has to poll UniPro and/or M-PHY state machine to confirm
the power mode change is finished.
Add a new wrapper function ufshcd_send_bsg_uic_cmd() and call it from
ufs_bsg_request() so that if a UIC SET command is targeting the PA_PWRMODE
attribute it can be redirected to ufshcd_uic_pwr_ctrl().
Fixes: e77044c5a842 ("scsi: ufs-bsg: Add support for uic commands in ufs_bsg_request()")
Co-developed-by: Can Guo <quic_cang@quicinc.com>
Signed-off-by: Can Guo <quic_cang@quicinc.com>
Signed-off-by: Ziqi Chen <quic_ziqichen@quicinc.com>
Link: https://lore.kernel.org/r/20241119095613.121385-1-quic_ziqichen@quicinc.com
Reviewed-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Peter Wang <peter.wang@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
show more ...
|
| 7670e74f | 08-Oct-2024 |
Ed Tsai <ed.tsai@mediatek.com> |
scsi: ufs: ufs-mediatek: Configure individual LU queue flags
Previously, ufs vops config_scsi_dev was removed because there were no
users. ufs-mediatek needs it to configure the queue flags for each
scsi: ufs: ufs-mediatek: Configure individual LU queue flags
Previously, ufs vops config_scsi_dev was removed because there were no
users. ufs-mediatek needs it to configure the queue flags for each LU
individually. Therefore, bring it back and customize the queue flag as
required.
[mkp: fixed typo]
Signed-off-by: Ed Tsai <ed.tsai@mediatek.com>
Link: https://lore.kernel.org/r/20241008065950.23431-1-ed.tsai@mediatek.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
show more ...
|
| 54c814c8 | 31-Oct-2024 |
Bart Van Assche <bvanassche@acm.org> |
scsi: ufs: core: Start the RTC update work later
The RTC update work involves runtime resuming the UFS controller. Hence,
only start the RTC update work after runtime power management in the UFS
dri
scsi: ufs: core: Start the RTC update work later
The RTC update work involves runtime resuming the UFS controller. Hence,
only start the RTC update work after runtime power management in the UFS
driver has been fully initialized. This patch fixes the following kernel
crash:
Internal error: Oops: 0000000096000006 [#1] PREEMPT SMP
Workqueue: events ufshcd_rtc_work
Call trace:
_raw_spin_lock_irqsave+0x34/0x8c (P)
pm_runtime_get_if_active+0x24/0x9c (L)
pm_runtime_get_if_active+0x24/0x9c
ufshcd_rtc_work+0x138/0x1b4
process_one_work+0x148/0x288
worker_thread+0x2cc/0x3d4
kthread+0x110/0x114
ret_from_fork+0x10/0x20
Reported-by: Neil Armstrong <neil.armstrong@linaro.org>
Closes: https://lore.kernel.org/linux-scsi/0c0bc528-fdc2-4106-bc99-f23ae377f6f5@linaro.org/
Fixes: 6bf999e0eb41 ("scsi: ufs: core: Add UFS RTC support")
Cc: Bean Huo <beanhuo@micron.com>
Cc: stable@vger.kernel.org
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20241031212632.2799127-1-bvanassche@acm.org
Reviewed-by: Peter Wang <peter.wang@mediatek.com>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-HDK
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
show more ...
|
| b92e5937 | 16-Oct-2024 |
Bart Van Assche <bvanassche@acm.org> |
scsi: ufs: core: Move code out of an if-statement
The previous patch in this series introduced identical code in both
branches of an if-statement. Move that code outside the if-statement.
Reviewed-
scsi: ufs: core: Move code out of an if-statement
The previous patch in this series introduced identical code in both
branches of an if-statement. Move that code outside the if-statement.
Reviewed-by: Bao D. Nguyen <quic_nguyenb@quicinc.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20241016201249.2256266-12-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
show more ...
|
| 72e97922 | 16-Oct-2024 |
Bart Van Assche <bvanassche@acm.org> |
scsi: ufs: core: Move the MCQ scsi_add_host() call
Whether or not MCQ is used, call scsi_add_host() from
ufshcd_add_scsi_host(). For MCQ this patch swaps the order of the
scsi_add_host() and UFS de
scsi: ufs: core: Move the MCQ scsi_add_host() call
Whether or not MCQ is used, call scsi_add_host() from
ufshcd_add_scsi_host(). For MCQ this patch swaps the order of the
scsi_add_host() and UFS device initialization. This patch prepares for
combining the two scsi_add_host() calls.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20241016201249.2256266-11-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
show more ...
|
| b6195d02 | 16-Oct-2024 |
Bart Van Assche <bvanassche@acm.org> |
scsi: ufs: core: Remove code that is no longer needed
Previous changes guarantee that hba->scsi_host_added is true before
ufshcd_device_init() is called. Hence, remove the code from
ufshcd_device_in
scsi: ufs: core: Remove code that is no longer needed
Previous changes guarantee that hba->scsi_host_added is true before
ufshcd_device_init() is called. Hence, remove the code from
ufshcd_device_init() that depends on hba->scsi_host_added being false.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20241016201249.2256266-10-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
show more ...
|
| a390e667 | 16-Oct-2024 |
Bart Van Assche <bvanassche@acm.org> |
scsi: ufs: core: Expand the ufshcd_device_init(hba, true) call
Expand the ufshcd_device_init(hba, true) call and remove all code that
depends on init_dev_params == false. This change prepares for co
scsi: ufs: core: Expand the ufshcd_device_init(hba, true) call
Expand the ufshcd_device_init(hba, true) call and remove all code that
depends on init_dev_params == false. This change prepares for combining
the two scsi_add_host() calls.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20241016201249.2256266-9-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
show more ...
|
| 69f5eb78 | 16-Oct-2024 |
Bart Van Assche <bvanassche@acm.org> |
scsi: ufs: core: Move the ufshcd_device_init(hba, true) call
ufshcd_async_scan() is called (asynchronously) only by ufshcd_init().
Move the ufshcd_device_init(hba, true) call from ufshcd_async_scan(
scsi: ufs: core: Move the ufshcd_device_init(hba, true) call
ufshcd_async_scan() is called (asynchronously) only by ufshcd_init().
Move the ufshcd_device_init(hba, true) call from ufshcd_async_scan()
into ufshcd_init(). This patch prepares for moving both scsi_add_host()
calls into ufshcd_add_scsi_host(). Calling ufshcd_device_init() from
ufshcd_init() without holding hba->host_sem is safe. This is safe
because hba->host_sem serializes core code and sysfs callbacks. The
ufshcd_device_init() call is moved before the scsi_add_host() call and
hence happens before any SCSI sysfs attributes are created.
Since ufshcd_device_init() may call scsi_add_host(), only call
scsi_add_host() from ufshcd_add_scsi_host() if the SCSI host has not yet
been added by ufshcd_device_init().
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20241016201249.2256266-8-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
show more ...
|
| 639e2043 | 16-Oct-2024 |
Bart Van Assche <bvanassche@acm.org> |
scsi: ufs: core: Move the ufshcd_device_init() calls
Move the ufshcd_device_init() and ufshcd_process_hba_result() calls to
the ufshcd_probe_hba() callers. This change refactors the code without
mod
scsi: ufs: core: Move the ufshcd_device_init() calls
Move the ufshcd_device_init() and ufshcd_process_hba_result() calls to
the ufshcd_probe_hba() callers. This change refactors the code without
modifying the behavior of the UFSHCI driver. This change prepares for
moving one ufshcd_device_init() call into ufshcd_init().
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20241016201249.2256266-7-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
show more ...
|
| 09360013 | 16-Oct-2024 |
Bart Van Assche <bvanassche@acm.org> |
scsi: ufs: core: Convert a comment into an explicit check
The comment /* UFSHCD_QUIRK_REINIT_AFTER_MAX_GEAR_SWITCH is set */ is
only correct if ufshcd_device_init() is only called by
ufshcd_probe_hb
scsi: ufs: core: Convert a comment into an explicit check
The comment /* UFSHCD_QUIRK_REINIT_AFTER_MAX_GEAR_SWITCH is set */ is
only correct if ufshcd_device_init() is only called by
ufshcd_probe_hba(). Convert the comment into an explicit check. This
patch prepares for moving the ufshcd_device_init() calls.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20241016201249.2256266-6-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
show more ...
|