/linux/Documentation/devicetree/bindings/phy/ |
H A D | microchip,lan966x-serdes.yaml | 13 Lan966x has 7 interfaces, consisting of 2 copper transceivers(CU), 22 CU(1) means use interface copper transceivers 1. SERDES6G(2) means use
|
/linux/drivers/phy/qualcomm/ |
H A D | Kconfig | 111 PHY transceivers working only in USB3 mode on Qualcomm chips. This 142 Enable this to support M31 HS PHY transceivers on Qualcomm chips 166 Enable this to support M31 EUSB2 PHY transceivers on Qualcomm
|
/linux/drivers/phy/ |
H A D | Kconfig | 78 This option enables support for CAN transceivers as a PHY. This 79 driver provides function for putting the transceivers in various
|
H A D | phy-can-transceiver.c | 3 * phy-can-transceiver.c - phy driver for CAN transceivers
|
/linux/drivers/usb/phy/ |
H A D | Kconfig | 94 Enable this to support some transceivers on OMAP1 platforms. OTG 154 Enable this to support ULPI connected USB OTG transceivers which
|
/linux/include/linux/usb/ |
H A D | usb_phy_generic.h | 8 /* sometimes transceivers are accessed only through e.g. ULPI */
|
/linux/drivers/tty/serial/8250/ |
H A D | 8250_ni.c | 87 dev_dbg(port->dev, "enable transceivers: write pcr: 0x%02x\n", pcr); in ni16550_enable_transceivers() 99 dev_dbg(port->dev, "disable transceivers: write pcr: 0x%02x\n", pcr); in ni16550_disable_transceivers() 141 * connected to RS-485 transceivers in is_pmr_rs232_mode()
|
/linux/Documentation/devicetree/bindings/net/bluetooth/ |
H A D | nokia,h4p-bluetooth.txt | 8 UART status lines for wakeup of UART transceivers to improve power management
|
/linux/arch/arm/boot/dts/microchip/ |
H A D | at91-sam9x60_curiosity.dts | 271 AT91_PIOC 9 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_DOWN>; /* Enable CAN Transceivers */ 280 AT91_PIOB 17 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_DOWN>; /* Enable CAN Transceivers */
|
H A D | at91-sam9x60ek.dts | 472 AT91_PIOD 21 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_DOWN>; /* Enable CAN Transceivers */ 482 AT91_PIOD 21 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_DOWN>; /* Enable CAN Transceivers */
|
/linux/Documentation/networking/ |
H A D | phy-link-topology.rst | 29 for example, using SFP transceivers (although that's not the only specific case).
|
/linux/Documentation/devicetree/bindings/net/ |
H A D | xlnx,axi-ethernet.yaml | 100 and transceivers.
|
/linux/include/uapi/linux/ |
H A D | mii.h | 3 * linux/mii.h: definitions for MII-compatible transceivers
|
/linux/drivers/net/ethernet/dec/tulip/ |
H A D | 21142.c | 27 of available transceivers. */
|
H A D | winbond-840.c | 532 This only set with older transceivers, so the extra 540 a few older transceivers. */
|
/linux/include/linux/ |
H A D | mii.h | 3 * linux/mii.h: definitions for MII-compatible transceivers
|
H A D | mdio.h | 3 * linux/mdio.h: definitions for MDIO (clause 45) transceivers
|
/linux/drivers/usb/host/ |
H A D | ehci-pci.c | 352 * transceivers that don't need any software attention to set up
|
H A D | ohci-at91.c | 638 * The integrated transceivers seem unable to notice disconnect, in ohci_hcd_at91_drv_suspend()
|
/linux/drivers/net/ethernet/sfc/falcon/ |
H A D | qt202x_phy.c | 411 * or optical transceivers, varying somewhat between in qt202x_phy_reconfigure()
|
/linux/drivers/net/ethernet/3com/ |
H A D | 3c574_cs.c | 409 pr_notice(" No MII transceivers found!\n"); in tc574_config() 529 a few older transceivers. */
|
H A D | 3c59x.c | 1363 pr_debug(" Internal config register is %4.4x, transceivers %#x.\n", in vortex_probe1() 1421 pr_warn(" ***WARNING*** No MII transceivers found!\n"); in vortex_probe1() 3141 a few older transceivers. */
|
/linux/drivers/net/phy/ |
H A D | broadcom.c | 6 * transceivers. 8 * Broadcom BCM54810, BCM54811 BroadR-Reach transceivers.
|
/linux/Documentation/scsi/ |
H A D | aic79xx.rst | 140 to reset our transceivers.
|
/linux/drivers/net/ethernet/sis/ |
H A D | sis190.c | 1424 pr_info("%s: No MII transceivers found!\n", in sis190_mii_probe()
|