Home
last modified time | relevance | path

Searched refs:cirrus (Results 1 – 25 of 57) sorted by relevance

123

/linux/Documentation/devicetree/bindings/sound/
H A Dcs35l35.txt5 - compatible : "cirrus,cs35l35"
17 - cirrus,boost-ind-nanohenry: Inductor value for boost converter. The value is
23 - cirrus,stereo-config : Boolean to determine if there are 2 AMPs for a
26 - cirrus,audio-channel : Set Location of Audio Signal on Serial Port
30 - cirrus,advisory-channel : Set Location of Advisory Signal on Serial Port
34 - cirrus,shared-boost : Boolean to enable ClassH tracking of Advisory Signal
37 - cirrus,external-boost : Boolean to specify the device is using an external
41 - cirrus,sp-drv-strength : Value for setting the Serial Port drive strength
45 - cirrus,sp-drv-unused : Determines how unused slots should be driven on the
51 - cirrus,bst-pdn-fet-on : Boolean to determine if the Boost PDN control
[all …]
H A Dcs35l36.txt5 - compatible : "cirrus,cs35l36"
13 - cirrus,boost-ctl-millivolt : Boost Voltage Value. Configures the boost
18 - cirrus,boost-peak-milliamp : Boost-converter peak current limit in mA.
24 - cirrus,boost-ind-nanohenry : Inductor estimation LBST reference value.
32 - cirrus,multi-amp-mode : Boolean to determine if there are more than
36 - cirrus,boost-ctl-select : Boost converter control source selection.
43 - cirrus,amp-pcm-inv : Boolean to determine Amplifier will invert incoming
46 - cirrus,imon-pol-inv : Boolean to determine Amplifier will invert the
49 - cirrus,vmon-pol-inv : Boolean to determine Amplifier will invert the
52 - cirrus,dcm-mode-enable : Boost converter automatic DCM Mode enable.
[all …]
H A Dcs43130.txt5 - compatible : "cirrus,cs43130", "cirrus,cs4399", "cirrus,cs43131",
6 "cirrus,cs43198"
19 - cirrus,xtal-ibias:
28 - cirrus,dc-measure:
31 - cirrus,ac-measure:
35 - cirrus,dc-threshold:
39 - cirrus,ac-freq:
41 Only used if "cirrus,dc-measure" is defined.
52 compatible = "cirrus,cs43130";
60 cirrus,xtal-ibias = <2>;
[all …]
H A Dcs35l33.txt5 - compatible : "cirrus,cs35l33"
21 - cirrus,boost-ctl : Booster voltage use to supply the amp. If the value is
26 - cirrus,ramp-rate : On power up, it affects the time from when the power
34 - cirrus,boost-ipk : The maximum current allowed for the boost converter.
38 - cirrus,imon-adc-scale : Configures the scaling of data bits from the IMON
45 The cs35l33 node can have a single "cirrus,hg-algo" sub-node that will enable
48 - cirrus,hg-algo : Sub-node for internal Class H/G algorithm that
51 Optional properties for the "cirrus,hg-algo" sub-node:
53 - cirrus,mem-depth : Memory depth for the Class H/G algorithm measured in
57 cirrus,release-rate : The number of consecutive LRCLK periods before
[all …]
H A Dcs42l56.txt5 - compatible : "cirrus,cs42l56"
14 - cirrus,gpio-nreset : GPIO controller's phandle and the number
17 - cirrus,chgfreq-divisor : Values used to set the Charge Pump Frequency.
24 - cirrus,ain1a-ref-cfg, ain1b-ref-cfg : boolean, If present, AIN1A or AIN1B are configured
27 - cirrus,ain2a-ref-cfg, ain2b-ref-cfg : boolean, If present, AIN2A or AIN2B are configured
30 - cirrus,micbias-lvl: Set the output voltage level on the MICBIAS Pin.
38 - cirrus,adaptive-pwr-cfg : Configures how the power to the Headphone and Lineout
45 …- cirrus,hpf-left-freq, hpf-right-freq : Sets the corner frequency (-3dB point) for the internal H…
56 compatible = "cirrus,cs42l56";
58 cirrus,gpio-nreset = <&gpio 10 0>;
[all …]
H A Dcs42l52.txt5 - compatible : "cirrus,cs42l52"
11 - cirrus,reset-gpio : GPIO controller's phandle and the number
14 - cirrus,chgfreq-divisor : Values used to set the Charge Pump Frequency.
21 - cirrus,mica-differential-cfg : boolean, If present, then the MICA input is configured
25 - cirrus,micb-differential-cfg : boolean, If present, then the MICB input is configured
29 - cirrus,micbias-lvl: Set the output voltage level on the MICBIAS Pin
40 compatible = "cirrus,cs42l52";
43 cirrus,chgfreq-divisor = <0x05>;
44 cirrus.mica-differential-cfg;
45 cirrus,micbias-lvl = <5>;
H A Dcs35l34.txt5 - compatible : "cirrus,cs35l34"
13 - cirrus,boost-vtge-millivolt : Boost Voltage Value. Configures the boost
17 - cirrus,boost-nanohenry: Inductor value for boost converter. The value is
28 - cirrus,boost-peak-milliamp : Boost converter peak current limit in mA. The
32 - cirrus,i2s-sdinloc : ADSP SDIN I2S channel location. Indicates whether the
41 - cirrus,gain-zc-disable: Boolean property. If set, the gain change will take
44 - cirrus,tdm-rising-edge: Boolean property. If set, data is on the rising edge of
51 compatible = "cirrus,cs35l34";
59 cirrus,boost-vtge-milltvolt = <8000>; /* 8V */
60 cirrus,boost-ind-nanohenry = <1000>; /* 1uH */
[all …]
H A Dcs35l32.txt5 - compatible : "cirrus,cs35l32"
18 - cirrus,boost-manager : Boost voltage control.
27 - cirrus,sdout-datacfg : Data configuration for dual CS35L32 applications only.
34 - cirrus,sdout-share : SDOUT sharing. Determines whether one or two CS35L32
39 - cirrus,battery-recovery : Low battery nominal recovery threshold, rising VP.
45 - cirrus,battery-threshold : Low battery nominal threshold, falling VP.
56 compatible = "cirrus,cs35l32";
59 cirrus,boost-manager = <0x03>;
60 cirrus,sdout-datacfg = <0x02>;
H A Dcs53l30.txt5 - compatible : "cirrus,cs53l30"
20 - cirrus,micbias-lvl : Set the output voltage level on the MICBIAS Pin.
25 - cirrus,use-sdout2 : This is a boolean property. If present, it indicates
39 compatible = "cirrus,cs53l30";
H A Dcs42l73.txt5 - compatible : "cirrus,cs42l73"
18 compatible = "cirrus,cs42l73";
/linux/arch/arm/boot/dts/cirrus/
H A Dep7209.dtsi11 compatible = "cirrus,ep7209";
46 compatible = "cirrus,ep7209-clk";
52 compatible = "cirrus,ep7209-intc";
59 compatible = "cirrus,ep7209-gpio";
66 compatible = "cirrus,ep7209-gpio";
73 compatible = "cirrus,ep7209-gpio";
80 compatible = "cirrus,ep7209-gpio";
87 compatible = "cirrus,ep7209-syscon1", "syscon";
94 compatible = "cirrus,ep7209-bus", "simple-bus";
110 compatible = "cirrus,ep7209-fb";
[all …]
H A Dep93xx.dtsi8 #include <dt-bindings/clock/cirrus,ep9301-syscon.h>
17 compatible = "cirrus,ep9301-syscon", "syscon";
100 compatible = "cirrus,ep9301-adc";
124 compatible = "cirrus,ep9301-dma-m2p";
157 compatible = "cirrus,ep9301-dma-m2m";
169 compatible = "cirrus,ep9301-eth";
180 compatible = "cirrus,ep9301-gpio";
194 compatible = "cirrus,ep9301-gpio";
208 compatible = "cirrus,ep9301-gpio";
219 compatible = "cirrus,ep9301-gpio";
[all …]
H A Dep7211.dtsi7 compatible = "cirrus,ep7211", "cirrus,ep7209";
H A Dep93xx-edb9302.dts11 compatible = "cirrus,edb9302", "cirrus,ep9301";
12 model = "cirrus,edb9302";
147 compatible = "cirrus,cs4271";
/linux/Documentation/devicetree/bindings/spi/
H A Dspi-clps711x.txt6 - compatible: should include "cirrus,ep7209-spi"
15 as compatible with "cirrus,ep7209-syscon3".
22 compatible = "cirrus,ep7209-spi";
29 compatible = "cirrus,ep7209-syscon3", "syscon";
/linux/Documentation/devicetree/bindings/net/
H A Dcirrus,cs89x0.txt4 - compatible : Should be "cirrus,cs8900" or "cirrus,cs8920".
10 compatible = "cirrus,cs8900";
/linux/Documentation/devicetree/bindings/pwm/
H A Dcirrus,clps711x-pwm.txt4 - compatible: Shall contain "cirrus,ep7209-pwm".
11 compatible = "cirrus,ep7312-pwm", "cirrus,ep7209-pwm";
/linux/sound/hda/codecs/side-codecs/
H A DMakefile4 snd-hda-cirrus-scodec-y := cirrus_scodec.o
5 snd-hda-cirrus-scodec-test-y := cirrus_scodec_test.o
17 obj-$(CONFIG_SND_HDA_CIRRUS_SCODEC) += snd-hda-cirrus-scodec.o
18 obj-$(CONFIG_SND_HDA_CIRRUS_SCODEC_KUNIT_TEST) += snd-hda-cirrus-scodec-test.o
/linux/Documentation/devicetree/bindings/input/
H A Dclps711x-keypad.txt4 - compatible: Shall contain "cirrus,ep7209-keypad".
15 compatible = "cirrus,ep7312-keypad", "cirrus,ep7209-keypad";
/linux/Documentation/devicetree/bindings/display/
H A Dcirrus,clps711x-fb.txt4 - compatible: Shall contain "cirrus,ep7209-fb".
21 compatible = "cirrus,ep7312-fb", "cirrus,ep7209-fb";
/linux/arch/arm64/boot/dts/qcom/
H A Dsm8350-sony-xperia-sagami.dtsi495 compatible = "cirrus,cs35l41";
500 cirrus,boost-peak-milliamp = <4000>;
501 cirrus,boost-ind-nanohenry = <1000>;
502 cirrus,boost-cap-microfarad = <15>;
503 cirrus,asp-sdout-hiz = <3>;
504 cirrus,gpio2-src-select = <2>;
505 cirrus,gpio2-output-enable;
510 compatible = "cirrus,cs35l41";
515 cirrus,boost-peak-milliamp = <4000>;
516 cirrus,boost-ind-nanohenry = <1000>;
[all …]
/linux/Documentation/sound/codecs/
H A Dcs35l56.rst9 Contact: patches@opensource.cirrus.com
170 …[ 9.242164] cs35l56 sdw:0:0:01fa:3556:01:0: DSP1: cirrus/cs35l56-b0-dsp1-misc-xxxxxxxx.wmfw: forma…
171 …[ 9.242173] cs35l56 sdw:0:0:01fa:3556:01:0: DSP1: cirrus/cs35l56-b0-dsp1-misc-xxxxxxxx.wmfw: Tue 0…
173 …[10.039098] cs35l56 sdw:0:0:01fa:3556:01:0: DSP1: cirrus/cs35l56-b0-dsp1-misc-xxxxxxxx-amp1.bin: v…
185 …[ 8.287525] cs35l56-hda i2c-CSC3556:00-cs35l56-hda.0: DSP1: cirrus/cs35l56-b0-dsp1-misc-xxxxxxxx.w…
186 …[ 8.287528] cs35l56-hda i2c-CSC3556:00-cs35l56-hda.0: DSP1: cirrus/cs35l56-b0-dsp1-misc-xxxxxxxx.w…
188 …[10.085797] cs35l56-hda i2c-CSC3556:00-cs35l56-hda.0: DSP1: cirrus/cs35l56-b0-dsp1-misc-xxxxxxxx-a…
211 DSP1: cirrus/cs35l56-b0-dsp1-misc-xxxxxxxx.wmfw
214 DSP1: cirrus/cs35l56-b0-dsp1-misc-xxxxxxxx-amp1.bin
/linux/drivers/soc/
H A DMakefile11 obj-$(CONFIG_EP93XX_SOC) += cirrus/
/linux/arch/arm/boot/dts/
H A DMakefile13 subdir-y += cirrus
/linux/arch/arm/boot/dts/marvell/
H A Dkirkwood-openrd-ultimate.dts25 compatible = "cirrus,cs42l51";

123