| /linux/tools/perf/pmu-events/arch/x86/silvermont/ |
| H A D | frontend.json | 7 …he BACLEARS event counts the number of times the front end is resteered, mainly when the Branch Pr…
16 …he BACLEARS event counts the number of times the front end is resteered, mainly when the Branch Pr…
25 …he BACLEARS event counts the number of times the front end is resteered, mainly when the Branch Pr…
|
| /linux/drivers/hsi/ |
| H A D | Kconfig | 9 synchronous serial interface used mainly to connect
|
| /linux/Documentation/devicetree/bindings/sound/ |
| H A D | widgets.txt | 3 This mainly specifies audio off-codec DAPM widgets.
|
| /linux/Documentation/devicetree/bindings/pwm/ |
| H A D | ti,twl-pwmled.txt | 5 On TWL6030 series: LED PWM (mainly used as charging indicator LED)
|
| /linux/Documentation/arch/arm/ |
| H A D | interrupts.rst | 13 There is more assembly code inside each of these functions, mainly to
48 We also bring the idea of an IRQ "chip" (mainly to reduce the size of
|
| /linux/drivers/i3c/ |
| H A D | Kconfig | 14 mainly designed to communicate with sensors.
|
| /linux/Documentation/ABI/testing/ |
| H A D | sysfs-bus-hsi | 7 serial interface mainly used for connecting application
|
| /linux/drivers/iio/dummy/ |
| H A D | Kconfig | 16 Driver intended mainly as documentation for how to write
|
| /linux/Documentation/admin-guide/media/ |
| H A D | ipu6-isys.rst | 29 The Input System mainly works as MIPI CSI-2 receiver which receives and
45 The Input System driver mainly configures CSI-2 D-PHY, constructs the firmware
|
| /linux/fs/squashfs/ |
| H A D | Kconfig | 171 compressed with LZ4 compression. LZ4 compression is mainly
186 compressed with LZO compression. LZO compression is mainly
|
| /linux/Documentation/devicetree/bindings/pci/ |
| H A D | snps,dw-pcie-ep.yaml | 56 mainly relevant for the end-point controller configuration,
87 region, but mainly these registers are indirectly accessible
|
| /linux/drivers/gpu/drm/omapdrm/ |
| H A D | TODO | 6 . This is mainly theoretical since most of these devices don't actually
|
| /linux/drivers/hid/surface-hid/ |
| H A D | Kconfig | 16 Surface Laptop 3. On those models, it is mainly used to connect the
|
| /linux/include/linux/ |
| H A D | ti_wilink_st.h | 96 * in progress, this is mainly used to return relevant err codes
230 * mainly used during fw download, which involves multiple send/wait
242 * @core_data: ST core's data, which mainly is the tty's disc_data
|
| /linux/Documentation/devicetree/bindings/media/ |
| H A D | cnm,wave521c.yaml | 43 storing it on DMA memory. It is mainly used for the purpose of reducing
|
| /linux/drivers/staging/vme_user/ |
| H A D | Kconfig | 38 is mainly useful for VME development (in the absence of VME
|
| /linux/drivers/nvdimm/ |
| H A D | pfn.h | 36 * configurations mainly to allow a backup, reconfigure the
|
| /linux/arch/arm/mach-davinci/ |
| H A D | pm.h | 23 * The SLEEPCOUNT feature is mainly intended for cases in which
|
| /linux/tools/testing/selftests/sync/ |
| H A D | sw_sync.h | 33 * sw_sync is mainly intended for testing and should not be compiled into
|
| /linux/Documentation/leds/ |
| H A D | leds-lp3944.rst | 43 The chip is used mainly in embedded contexts, so this driver expects it is
|
| /linux/Documentation/admin-guide/nfs/ |
| H A D | nfsd-admin-interfaces.rst | 8 nfsd is controlled mainly by pseudofiles under the "nfsd" filesystem,
|
| /linux/include/asm-generic/ |
| H A D | checksum.h | 60 * this routine is used for miscellaneous IP-like checksums, mainly
|
| /linux/drivers/clk/baikal-t1/ |
| H A D | Kconfig | 48 AXI-bus and some subsystems reset. These are mainly the
|
| /linux/drivers/platform/x86/siemens/ |
| H A D | Kconfig | 10 is mainly used for system identification, after which drivers in other
|
| /linux/Documentation/filesystems/ext4/ |
| H A D | bigalloc.rst | 17 file system is mainly going to be storing large files in the 4-32
|