Lines Matching +full:default +full:- +full:on
1 # SPDX-License-Identifier: GPL-2.0-only
7 default y if ARCH_HAS_RESET_CONTROLLER
12 via GPIOs or SoC-internal reset controller modules.
20 depends on MFD_ALTERA_A10SR || COMPILE_TEST
23 peripheral PHYs on the Altera Arria10 System Resource Chip.
27 depends on ARCH_ASPEED || COMPILE_TEST
34 default ATH79
41 default ARC_PLAT_AXS10X
47 depends on BMIPS_GENERIC || COMPILE_TEST
48 default BMIPS_GENERIC
54 depends on ARCH_BERLIN || COMPILE_TEST
55 default m if ARCH_BERLIN
61 depends on ARCH_BRCMSTB || ARCH_BCM2835 || COMPILE_TEST
62 default ARCH_BRCMSTB || ARCH_BCM2835
69 depends on HAS_IOMEM
70 depends on ARCH_BRCMSTB || ARCH_BCM2835 || COMPILE_TEST
71 default ARCH_BRCMSTB || ARCH_BCM2835
73 This enables the RESCAL reset controller for SATA, PCIe0, or PCIe1 on
78 depends on ARCH_ESWIN || COMPILE_TEST
79 default ARCH_ESWIN
84 asserting and deasserting resets on the chip.
88 depends on MACH_EYEQ5 || MACH_EYEQ6H || COMPILE_TEST
90 default MACH_EYEQ5 || MACH_EYEQ6H
101 depends on GPIOLIB
105 GPIOs. Typically for OF platforms this driver expects "reset-gpios"
108 If compiled as module, it will be called reset-gpio.
112 depends on HAS_IOMEM
113 depends on ARC_SOC_HSDK || COMPILE_TEST
119 depends on IMX_SCU && HAVE_ARM_SMCCC
120 depends on (ARM64 && ARCH_MXC) || COMPILE_TEST
126 depends on HAS_IOMEM
127 depends on SOC_IMX7D || (ARM64 && ARCH_MXC) || COMPILE_TEST
128 default y if SOC_IMX7D
135 depends on ARCH_MXC || COMPILE_TEST
137 default CLK_IMX8MP
143 depends on X86 || COMPILE_TEST
144 depends on OF && HAS_IOMEM
153 depends on (SOC_CANAAN_K210 || COMPILE_TEST) && OF
155 default SOC_CANAAN_K210
157 Support for the Canaan Kendryte K210 RISC-V SoC reset controller.
163 depends on ARCH_CANAAN || COMPILE_TEST
164 depends on OF
166 Support for the Canaan Kendryte K230 RISC-V SoC reset controller.
172 default SOC_TYPE_XWAY
178 default ARCH_LPC18XX
184 depends on ARCH_SPARX5 || ARCH_LAN969X || SOC_LAN966 || MCHP_LAN966X_PCI || COMPILE_TEST
185 default y if SPARX5_SWITCH
192 default ARCH_NPCM
200 depends on ARCH_MA35 || COMPILE_TEST
201 default ARCH_MA35
207 depends on MIPS || COMPILE_TEST
213 depends on MCHP_CLK_MPFS
214 depends on MFD_SYSCON
216 default MCHP_CLK_MPFS
222 depends on ARCH_QCOM || COMPILE_TEST
224 This enables the AOSS (always on subsystem) reset driver
231 depends on ARCH_QCOM || COMPILE_TEST
240 depends on RASPBERRYPI_FIRMWARE || (RASPBERRYPI_FIRMWARE=n && COMPILE_TEST)
241 default USB_XHCI_PCI
243 Raspberry Pi 4's co-processor controls some of the board's HW
246 interfacing with RPi4's co-processor and model these firmware
251 depends on ARCH_RZG2L || COMPILE_TEST
254 Support for USBPHY Control found on RZ/G2L family. It mainly
259 depends on ARCH_RENESAS || COMPILE_TEST
261 Support for USB2PHY Port reset Control found on the RZ/V2H(P) SoC
266 depends on ARM_SCMI_PROTOCOL || COMPILE_TEST
267 default ARM_SCMI_PROTOCOL
277 …default ARCH_ASPEED || ARCH_BCMBCA || ARCH_BITMAIN || ARCH_REALTEK || ARCH_SOPHGO || ARCH_STM32 ||…
278 depends on HAS_IOMEM
285 - Altera SoCFPGAs
286 - ASPEED BMC SoCs
287 - Bitmain BM1880 SoC
288 - Realtek SoCs
289 - RCC reset controller in STM32 MCUs
290 - Allwinner SoCs
291 - SiFive FU740 SoCs
292 - Sophgo SoCs
296 default ARM && ARCH_INTEL_SOCFPGA
304 depends on ARCH_SPACEMIT || COMPILE_TEST
306 default ARCH_SPACEMIT
313 default ARCH_SUNPLUS
322 default ARCH_SUNXI
328 tristate "T-HEAD TH1520 reset controller"
329 depends on ARCH_THEAD || COMPILE_TEST
332 This driver provides support for the T-HEAD TH1520 SoC reset controller,
334 Enable this option if you need to control hardware resets on TH1520-based
338 tristate "TI System Control Interface (TI-SCI) reset driver"
339 depends on TI_SCI_PROTOCOL || (COMPILE_TEST && TI_SCI_PROTOCOL=n)
342 available on some new TI's SoCs. If you wish to use reset resources
347 depends on HAS_IOMEM
351 memory-mapped reset registers as part of a syscon device node. If
352 you wish to use the reset framework for such memory-mapped devices,
365 depends on MFD_TN48M_CPLD || COMPILE_TEST
366 default MFD_TN48M_CPLD
369 It provides reset signals for Armada 7040 and 385 SoC-s, Alleycat 3X
370 switch MAC-s, Alaska OOB ethernet PHY, Quad Alaska ethernet PHY-s and
374 called reset-tn48m.
378 depends on ARCH_UNIPHIER || COMPILE_TEST
379 depends on OF && MFD_SYSCON
380 default ARCH_UNIPHIER
382 Support for reset controllers on UniPhier SoCs.
388 depends on (ARCH_UNIPHIER || COMPILE_TEST) && OF
389 default ARCH_UNIPHIER
393 on UniPhier SoCs. Say Y if you want to control reset signals
398 default ARCH_ZYNQ
404 default ARCH_ZYNQMP