| #
1c2b4a4c |
| 12-Feb-2026 |
Linus Torvalds <torvalds@linux-foundation.org> |
Merge tag 'pci-v7.0-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Don't try to enable Extended Tags on VFs since that bi
Merge tag 'pci-v7.0-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Don't try to enable Extended Tags on VFs since that bit is Reserved
and causes misleading log messages (Håkon Bugge)
- Initialize Endpoint Read Completion Boundary to match Root Port,
regardless of ACPI _HPX (Håkon Bugge)
- Apply _HPX PCIe Setting Record only to AER configuration, and only
when OS owns PCIe hotplug but not AER, to avoid clobbering Extended
Tag and Relaxed Ordering settings (Håkon Bugge)
Resource management:
- Move CardBus code to setup-cardbus.c and only build it when
CONFIG_CARDBUS is set (Ilpo Järvinen)
- Fix bridge window alignment with optional resources, where
additional alignment requirement was previously lost (Ilpo
Järvinen)
- Stop over-estimating bridge window size since they are now assigned
without any gaps between them (Ilpo Järvinen)
- Increase resource MAX_IORES_LEVEL to avoid /proc/iomem flattening
for nested bridges and endpoints (Ilpo Järvinen)
- Add pbus_mem_size_optional() to handle sizes of optional resources
(SR-IOV VF BARs, expansion ROMs, bridge windows) (Ilpo Järvinen)
- Don't claim disabled bridge windows to avoid spurious claim
failures (Ilpo Järvinen)
Driver binding:
- Fix device reference leak in pcie_port_remove_service() (Uwe
Kleine-König)
- Move pcie_port_bus_match() and pcie_port_bus_type to PCIe-specific
portdrv.c (Uwe Kleine-König)
- Convert portdrv to use pcie_port_bus_type.probe() and .remove()
callbacks so .probe() and .remove() can eventually be removed from
struct device_driver (Uwe Kleine-König)
Error handling:
- Clear stale errors on reporting agents upon probe so they don't
look like recent errors (Lukas Wunner)
- Add generic RAS tracepoint for hotplug events (Shuai Xue)
- Add RAS tracepoint for link speed changes (Shuai Xue)
Power management:
- Avoid redundant delay on transition from D3hot to D3cold if the
device was already in D3hot (Brian Norris)
- Prevent runtime suspend until devices are fully initialized to
avoid saving incompletely configured device state (Brian Norris)
Power control:
- Add power_on/off callbacks with generic signature to pwrseq,
tc9563, and slot drivers so they can be used by pwrctrl core
(Manivannan Sadhasivam)
- Add PCIe M.2 connector support to the slot pwrctrl driver
(Manivannan Sadhasivam)
- Switch to pwrctrl interfaces to create, destroy, and power on/off
devices, calling them from host controller drivers instead of the
PCI core (Manivannan Sadhasivam)
- Drop qcom .assert_perst() callbacks since this is now done by the
controller driver instead of the pwrctrl driver (Manivannan
Sadhasivam)
Virtualization:
- Remove an incorrect unlock in pci_slot_trylock() error handling
(Jinhui Guo)
- Lock the bridge device for slot reset (Keith Busch)
- Enable ACS after IOMMU configuration on OF platforms so ACS is
enabled an all devices; previously the first device enumerated
(typically a Root Port) didn't have ACS enabled (Manivannan
Sadhasivam)
- Disable ACS Source Validation for IDT 0x80b5 and 0x8090 switches to
work around hardware erratum; previously ACS SV was only
temporarily disabled, which worked for enumeration but not after
reset (Manivannan Sadhasivam)
Peer-to-peer DMA:
- Release per-CPU pgmap ref when vm_insert_page() fails to avoid hang
when removing the PCI device (Hou Tao)
- Remove incorrect p2pmem_alloc_mmap() warning about page refcount
(Hou Tao)
Endpoint framework:
- Add configfs sub-groups synchronously to avoid NULL pointer
dereference when racing with removal (Liu Song)
- Fix swapped parameters in pci_{primary/secondary}_epc_epf_unlink()
functions (Manikanta Maddireddy)
ASPEED PCIe controller driver:
- Add ASPEED Root Complex DT binding and driver (Jacky Chou)
Freescale i.MX6 PCIe controller driver:
- Add DT binding and driver support for an optional external refclock
in addition to the refclock from the internal PLL (Richard Zhu)
- Fix CLKREQ# control so host asserts it during enumeration and
Endpoints can use it afterwards to exit the L1.2 link state
(Richard Zhu)
NVIDIA Tegra PCIe controller driver:
- Export irq_domain_free_irqs() to allow PCI/MSI drivers that tear
down MSI domains to be built as modules (Aaron Kling)
- Allow pci-tegra to be built as a module (Aaron Kling)
NVIDIA Tegra194 PCIe controller driver:
- Relax Kconfig so tegra194 can be built for platforms beyond
Tegra194 (Vidya Sagar)
Qualcomm PCIe controller driver:
- Merge SC8180x DT binding into SM8150 (Krzysztof Kozlowski)
- Move SDX55, SDM845, QCS404, IPQ5018, IPQ6018, IPQ8074 Gen3,
IPQ8074, IPQ4019, IPQ9574, APQ8064, MSM8996, APQ8084 to dedicated
schema (Krzysztof Kozlowski)
- Add DT binding and driver support for SA8255p Endpoint being
configured by firmware (Mrinmay Sarkar)
- Parse PERST# from all PCIe bridge nodes for future platforms that
will have PERST# in Switch Downstream Ports as well as in Root
Ports (Manivannan Sadhasivam)
Renesas RZ/G3S PCIe controller driver:
- Use pci_generic_config_write() since the writability provided by
the custom wrapper is unnecessary (Claudiu Beznea)
SOPHGO PCIe controller driver:
- Disable ASPM L0s and L1 on Sophgo 2044 PCIe Root Ports (Inochi
Amaoto)
Synopsys DesignWare PCIe controller driver:
- Extend PCI_FIND_NEXT_CAP() and PCI_FIND_NEXT_EXT_CAP() to return a
pointer to the preceding Capability, to allow removal of
Capabilities that are advertised but not fully implemented (Qiang
Yu)
- Remove MSI and MSI-X Capabilities in platforms that can't support
them, so the PCI core automatically falls back to INTx (Qiang Yu)
- Add ASPM L1.1 and L1.2 Substates context to debugfs ltssm_status
for drivers that support this (Shawn Lin)
- Skip PME_Turn_Off broadcast and L2/L3 transition during suspend if
link is not up to avoid an unnecessary timeout (Manivannan
Sadhasivam)
- Revert dw-rockchip, qcom, and DWC core changes that used link-up
IRQs to trigger enumeration instead of waiting for link to be up
because the PCI core doesn't allocate bus number space for
hierarchies that might be attached (Niklas Cassel)
- Make endpoint iATU entry for MSI permanent instead of programming
it dynamically, which is slow and racy with respect to other
concurrent traffic, e.g., eDMA (Koichiro Den)
- Use iMSI-RX MSI target address when possible to fix endpoints using
32-bit MSI (Shawn Lin)
- Allow DWC host controller driver probe to continue if device is not
found or found but inactive; only fail when there's an error with
the link (Manivannan Sadhasivam)
- For controllers like NXP i.MX6QP and i.MX7D, where LTSSM registers
are not accessible after PME_Turn_Off, simply wait 10ms instead of
polling for L2/L3 Ready (Richard Zhu)
- Use multiple iATU entries to map large bridge windows and DMA
ranges when necessary instead of failing (Samuel Holland)
- Add EPC dynamic_inbound_mapping feature bit for Endpoint
Controllers that can update BAR inbound address translation without
requiring EPF driver to clear/reset the BAR first, and advertise it
for DWC-based Endpoints (Koichiro Den)
- Add EPC subrange_mapping feature bit for Endpoint Controllers that
can map multiple independent inbound regions in a single BAR,
implement subrange mapping, advertise it for DWC-based Endpoints,
and add Endpoint selftests for it (Koichiro Den)
- Make resizable BARs work for Endpoint multi-PF configurations;
previously it only worked for PF 0 (Aksh Garg)
- Fix Endpoint non-PF 0 support for BAR configuration, ATU mappings,
and Address Match Mode (Aksh Garg)
- Set up iATU when ECAM is enabled; previously IO and MEM outbound
windows weren't programmed, and ECAM-related iATU entries weren't
restored after suspend/resume, so config accesses failed (Krishna
Chaitanya Chundru)
Miscellaneous:
- Use system_percpu_wq and WQ_PERCPU to explicitly request per-CPU
work so WQ_UNBOUND can eventually be removed (Marco Crivellari)"
* tag 'pci-v7.0-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (176 commits)
PCI/bwctrl: Disable BW controller on Intel P45 using a quirk
PCI: Disable ACS SV for IDT 0x8090 switch
PCI: Disable ACS SV for IDT 0x80b5 switch
PCI: Cache ACS Capabilities register
PCI: Enable ACS after configuring IOMMU for OF platforms
PCI: Add ACS quirk for Pericom PI7C9X2G404 switches [12d8:b404]
PCI: Add ACS quirk for Qualcomm Hamoa & Glymur
PCI: Use device_lock_assert() to verify device lock is held
PCI: Use lockdep_assert_held(pci_bus_sem) to verify lock is held
PCI: Fix pci_slot_lock () device locking
PCI: Fix pci_slot_trylock() error handling
PCI: Mark Nvidia GB10 to avoid bus reset
PCI: Mark ASM1164 SATA controller to avoid bus reset
PCI: host-generic: Avoid reporting incorrect 'missing reg property' error
PCI/PME: Replace RMW of Root Status register with direct write
PCI/AER: Clear stale errors on reporting agents upon probe
PCI: Don't claim disabled bridge windows
PCI: rzg3s-host: Fix device node reference leak in rzg3s_pcie_host_parse_port()
PCI: dwc: Fix missing iATU setup when ECAM is enabled
PCI: dwc: Clean up iATU index usage in dw_pcie_iatu_setup()
...
show more ...
|
| #
73b47798 |
| 07-Feb-2026 |
Bjorn Helgaas <bhelgaas@google.com> |
Merge branch 'pci/resource'
- Build zero-sized resources when a BAR is larger than 4G but
pci_bus_addr_t or resource_size_t can't represent 64-bit addresses (Ilpo
Järvinen)
- Fix bridge window
Merge branch 'pci/resource'
- Build zero-sized resources when a BAR is larger than 4G but
pci_bus_addr_t or resource_size_t can't represent 64-bit addresses (Ilpo
Järvinen)
- Fix bridge window alignment with optional resources, where we previously
lost the additional alignment requirement (Ilpo Järvinen)
- Stop over-estimating bridge window size since we now assign them without
any gaps between them (Ilpo Järvinen)
- Increase resource MAX_IORES_LEVEL to avoid /proc/iomem flattening for
nested bridges and endpoints (Ilpo Järvinen)
- Remove old_size limit from bridge window sizing (Ilpo Järvinen)
- Push realloc check into pbus_size_mem() to simplify callers (Ilpo
Järvinen)
- Pass bridge window resource to pbus_size_mem() to avoid looking it up
again (Ilpo Järvinen)
- Use res_to_dev_res() instead of open-coding the same search (Ilpo
Järvinen)
- Add pci_resource_is_bridge_win() helper (Ilpo Järvinen)
- Add more logging of resource assignment (Ilpo Järvinen)
- Add pbus_mem_size_optional() to handle sizes of optional resources
(SR-IOV VF BARs, expansion ROMs, bridge windows) (Ilpo Järvinen)
- Move CardBus code to setup-cardbus.c and only build it when
CONFIG_CARDBUS is set (Ilpo Järvinen)
- Use scnprintf() instead of sprintf() (Ilpo Järvinen)
- Add pbus_validate_busn() for Bus Number validation (Ilpo Järvinen)
- Don't claim disabled bridge windows to avoid spurious claim failures
(Ilpo Järvinen)
* pci/resource:
PCI: Don't claim disabled bridge windows
PCI: Move CardBus bridge scanning to setup-cardbus.c
PCI: Add pbus_validate_busn() for Bus Number validation
PCI: Add dword #defines for Bus Number + Secondary Latency Timer
PCI: Use scnprintf() instead of sprintf()
PCI: Handle CardBus-specific params in setup-cardbus.c
PCI: Separate CardBus setup & build it only with CONFIG_CARDBUS
PCI: Add 'pci' prefix to struct pci_dev_resource handling functions
PCI: Use resource_assigned() in setup-bus.c algorithm
resource: Mark res given to resource_assigned() as const
PCI: Add pbus_mem_size_optional() to handle optional sizes
PCI: Check invalid align earlier in pbus_size_mem()
PCI: Log reset and restore of resources
PCI: Add pci_resource_is_bridge_win()
PCI: Fetch dev_res to local var in __assign_resources_sorted()
PCI: Use res_to_dev_res() in reassign_resources_sorted()
PCI: Pass bridge window resource to pbus_size_mem()
PCI: Push realloc check into pbus_size_mem()
PCI: Remove old_size limit from bridge window sizing
resource: Increase MAX_IORES_LEVEL to 8
PCI: Stop over-estimating bridge window size
PCI: Rewrite bridge window head alignment function
PCI: Fix bridge window alignment with optional resources
PCI: Use resource_set_range() that correctly sets ->end
show more ...
|
| #
08b3af83 |
| 19-Dec-2025 |
Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> |
PCI: Handle CardBus-specific params in setup-cardbus.c
Move CardBus window sizing parameters to setup-cardbus.c, which contains
all the other CardBus code.
Signed-off-by: Ilpo Järvinen <ilpo.jarvin
PCI: Handle CardBus-specific params in setup-cardbus.c
Move CardBus window sizing parameters to setup-cardbus.c, which contains
all the other CardBus code.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/20251219174036.16738-19-ilpo.jarvinen@linux.intel.com
show more ...
|