1// SPDX-License-Identifier: GPL-2.0-only 2 3/dts-v1/; 4 5#include "msm8916-pm8916.dtsi" 6#include "msm8916-modem-qdsp6.dtsi" 7 8#include <dt-bindings/gpio/gpio.h> 9#include <dt-bindings/input/input.h> 10#include <dt-bindings/interrupt-controller/irq.h> 11#include <dt-bindings/leds/common.h> 12 13/ { 14 model = "Longcheer L8150"; 15 compatible = "longcheer,l8150", "qcom,msm8916"; 16 chassis-type = "handset"; 17 18 aliases { 19 mmc0 = &sdhc_1; /* eMMC */ 20 mmc1 = &sdhc_2; /* SD card */ 21 serial0 = &blsp_uart2; 22 }; 23 24 chosen { 25 stdout-path = "serial0"; 26 }; 27 28 /* 29 * For some reason, the signed wcnss firmware is not relocatable. 30 * It must be loaded at 0x8b600000. Unfortunately, this also means that 31 * mpss_mem does not fit when loaded to the typical address at 0x86800000. 32 * 33 * Load wcnss_mem to the fixed address and relocate mpss_mem to the next 34 * working higher address. For some reason the modem firmware does not 35 * boot when placed at 0x8a800000 to 0x8e800000. 36 */ 37 reserved-memory { 38 /delete-node/ mpss@86800000; 39 /delete-node/ wcnss; 40 41 wcnss_mem: wcnss@8b600000 { 42 reg = <0x0 0x8b600000 0x0 0x600000>; 43 no-map; 44 }; 45 46 mpss_mem: mpss@8e800000 { 47 reg = <0x0 0x8e800000 0x0 0x5000000>; 48 no-map; 49 }; 50 }; 51 52 battery: battery { 53 compatible = "simple-battery"; 54 voltage-min-design-microvolt = <3400000>; 55 voltage-max-design-microvolt = <4350000>; 56 energy-full-design-microwatt-hours = <9500000>; 57 charge-full-design-microamp-hours = <2500000>; 58 59 ocv-capacity-celsius = <25>; 60 ocv-capacity-table-0 = <4330000 100>, <4265000 95>, 61 <4208000 90>, <4153000 85>, <4100000 80>, <4049000 75>, 62 <4001000 70>, <3962000 65>, <3919000 60>, <3872000 55>, 63 <3839000 50>, <3817000 45>, <3798000 40>, <3783000 35>, 64 <3767000 30>, <3747000 25>, <3729000 20>, <3709000 16>, 65 <3688000 13>, <3681000 11>, <3680000 10>, <3679000 9>, 66 <3677000 8>, <3674000 7>, <3666000 6>, <3641000 5>, 67 <3597000 4>, <3537000 3>, <3457000 2>, <3336000 1>, 68 <3000000 0>; 69 }; 70 71 gpio-keys { 72 compatible = "gpio-keys"; 73 74 pinctrl-names = "default"; 75 pinctrl-0 = <&gpio_keys_default>; 76 77 label = "GPIO Buttons"; 78 79 button-volume-up { 80 label = "Volume Up"; 81 gpios = <&tlmm 107 GPIO_ACTIVE_LOW>; 82 linux,code = <KEY_VOLUMEUP>; 83 }; 84 }; 85 86 reg_ctp: regulator-ctp { 87 compatible = "regulator-fixed"; 88 regulator-name = "ctp"; 89 90 regulator-min-microvolt = <2800000>; 91 regulator-max-microvolt = <2800000>; 92 93 gpio = <&tlmm 17 GPIO_ACTIVE_HIGH>; 94 enable-active-high; 95 96 pinctrl-names = "default"; 97 pinctrl-0 = <&ctp_pwr_en_default>; 98 }; 99 100 flash-led-controller { 101 compatible = "sgmicro,sgm3140"; 102 flash-gpios = <&tlmm 31 GPIO_ACTIVE_HIGH>; 103 enable-gpios = <&tlmm 32 GPIO_ACTIVE_HIGH>; 104 105 pinctrl-names = "default"; 106 pinctrl-0 = <&camera_flash_default>; 107 108 flash_led: led { 109 function = LED_FUNCTION_FLASH; 110 color = <LED_COLOR_ID_WHITE>; 111 flash-max-timeout-us = <250000>; 112 }; 113 }; 114}; 115 116&blsp_i2c1 { 117 status = "okay"; 118 119 led-controller@45 { 120 compatible = "awinic,aw2013"; 121 reg = <0x45>; 122 #address-cells = <1>; 123 #size-cells = <0>; 124 125 vcc-supply = <&pm8916_l17>; 126 vio-supply = <&pm8916_l6>; 127 128 led@0 { 129 reg = <0>; 130 led-max-microamp = <5000>; 131 function = LED_FUNCTION_INDICATOR; 132 color = <LED_COLOR_ID_RED>; 133 }; 134 135 led@1 { 136 reg = <1>; 137 led-max-microamp = <5000>; 138 function = LED_FUNCTION_INDICATOR; 139 color = <LED_COLOR_ID_GREEN>; 140 }; 141 142 led@2 { 143 reg = <2>; 144 led-max-microamp = <5000>; 145 function = LED_FUNCTION_INDICATOR; 146 color = <LED_COLOR_ID_BLUE>; 147 }; 148 }; 149}; 150 151&blsp_i2c2 { 152 status = "okay"; 153 154 accelerometer@10 { 155 compatible = "bosch,bmc156_accel"; 156 reg = <0x10>; 157 158 /* 159 * For some reason the interrupt line is usually not connected 160 * to the BMC156. However, there are two pads next to the chip 161 * that can be shorted to make it work if needed. 162 * 163 * interrupt-parent = <&tlmm>; 164 * interrupts = <116 IRQ_TYPE_EDGE_RISING>; 165 */ 166 167 pinctrl-names = "default"; 168 pinctrl-0 = <&accel_int_default>; 169 170 vdd-supply = <&pm8916_l17>; 171 vddio-supply = <&pm8916_l6>; 172 173 mount-matrix = "0", "1", "0", 174 "-1", "0", "0", 175 "0", "0", "1"; 176 }; 177 178 magnetometer@12 { 179 compatible = "bosch,bmc156_magn"; 180 reg = <0x12>; 181 182 interrupt-parent = <&tlmm>; 183 interrupts = <113 IRQ_TYPE_EDGE_RISING>; 184 185 pinctrl-names = "default"; 186 pinctrl-0 = <&magn_int_default>; 187 188 vdd-supply = <&pm8916_l17>; 189 vddio-supply = <&pm8916_l6>; 190 }; 191 192 light-sensor@23 { 193 compatible = "liteon,ltr559"; 194 reg = <0x23>; 195 proximity-near-level = <75>; 196 197 interrupt-parent = <&tlmm>; 198 interrupts = <115 IRQ_TYPE_EDGE_FALLING>; 199 200 pinctrl-names = "default"; 201 pinctrl-0 = <&light_int_default>; 202 203 vdd-supply = <&pm8916_l17>; 204 vddio-supply = <&pm8916_l6>; 205 }; 206 207 gyroscope@68 { 208 compatible = "bosch,bmg160"; 209 reg = <0x68>; 210 211 interrupt-parent = <&tlmm>; 212 interrupts = <23 IRQ_TYPE_EDGE_RISING>, 213 <22 IRQ_TYPE_EDGE_RISING>; 214 215 pinctrl-names = "default"; 216 pinctrl-0 = <&gyro_int_default>; 217 218 vdd-supply = <&pm8916_l17>; 219 vddio-supply = <&pm8916_l6>; 220 }; 221}; 222 223&blsp_i2c5 { 224 status = "okay"; 225 226 rmi4@20 { 227 compatible = "syna,rmi4-i2c"; 228 reg = <0x20>; 229 #address-cells = <1>; 230 #size-cells = <0>; 231 232 interrupt-parent = <&tlmm>; 233 interrupts = <13 IRQ_TYPE_EDGE_FALLING>; 234 235 vdd-supply = <®_ctp>; 236 vio-supply = <&pm8916_l6>; 237 238 pinctrl-names = "default"; 239 pinctrl-0 = <&tp_int_default>; 240 241 syna,startup-delay-ms = <10>; 242 243 rmi4-f01@1 { 244 reg = <0x1>; 245 syna,nosleep-mode = <1>; /* Allow sleeping */ 246 }; 247 248 rmi4-f12@12 { 249 reg = <0x12>; 250 syna,sensor-type = <1>; /* Touchscreen */ 251 }; 252 }; 253}; 254 255&blsp_uart2 { 256 status = "okay"; 257 pinctrl-0 = <&blsp_uart2_console_default>; 258 pinctrl-1 = <&blsp_uart2_console_sleep>; 259 pinctrl-names = "default", "sleep"; 260}; 261 262&pm8916_bms { 263 status = "okay"; 264 265 monitored-battery = <&battery>; 266 power-supplies = <&pm8916_charger>; 267}; 268 269&pm8916_charger { 270 status = "okay"; 271 272 monitored-battery = <&battery>; 273 274 qcom,fast-charge-safe-current = <900000>; 275 qcom,fast-charge-safe-voltage = <4300000>; 276}; 277 278&pm8916_codec { 279 qcom,micbias-lvl = <2800>; 280 qcom,mbhc-vthreshold-low = <75 150 237 450 500>; 281 qcom,mbhc-vthreshold-high = <75 150 237 450 500>; 282 qcom,hphl-jack-type-normally-open; 283}; 284 285&pm8916_resin { 286 status = "okay"; 287 linux,code = <KEY_VOLUMEDOWN>; 288}; 289 290&pm8916_rpm_regulators { 291 pm8916_l17: l17 { 292 regulator-min-microvolt = <2850000>; 293 regulator-max-microvolt = <2850000>; 294 }; 295}; 296 297&pm8916_vib { 298 status = "okay"; 299}; 300 301&sdhc_1 { 302 status = "okay"; 303}; 304 305&sdhc_2 { 306 status = "okay"; 307 non-removable; 308}; 309 310&sound { 311 audio-routing = 312 "AMIC1", "MIC BIAS Internal1", 313 "AMIC2", "MIC BIAS Internal2", 314 "AMIC3", "MIC BIAS Internal3"; 315}; 316 317&usb { 318 status = "okay"; 319 dr_mode = "peripheral"; 320 extcon = <&pm8916_charger>; 321}; 322 323&usb_hs_phy { 324 extcon = <&pm8916_charger>; 325}; 326 327&venus { 328 status = "okay"; 329}; 330 331&venus_mem { 332 status = "okay"; 333}; 334 335&wcnss { 336 status = "okay"; 337}; 338 339&wcnss_iris { 340 compatible = "qcom,wcn3620"; 341}; 342 343&wcnss_mem { 344 status = "okay"; 345}; 346 347&tlmm { 348 accel_int_default: accel-int-default-state { 349 pins = "gpio116"; 350 function = "gpio"; 351 352 drive-strength = <2>; 353 bias-disable; 354 }; 355 356 camera_flash_default: camera-flash-default-state { 357 pins = "gpio31", "gpio32"; 358 function = "gpio"; 359 360 drive-strength = <2>; 361 bias-disable; 362 }; 363 364 ctp_pwr_en_default: ctp-pwr-en-default-state { 365 pins = "gpio17"; 366 function = "gpio"; 367 368 drive-strength = <2>; 369 bias-disable; 370 }; 371 372 gpio_keys_default: gpio-keys-default-state { 373 pins = "gpio107"; 374 function = "gpio"; 375 376 drive-strength = <2>; 377 bias-pull-up; 378 }; 379 380 gyro_int_default: gyro-int-default-state { 381 pins = "gpio22", "gpio23"; 382 function = "gpio"; 383 384 drive-strength = <2>; 385 bias-disable; 386 }; 387 388 light_int_default: light-int-default-state { 389 pins = "gpio115"; 390 function = "gpio"; 391 392 drive-strength = <2>; 393 bias-disable; 394 }; 395 396 magn_int_default: magn-int-default-state { 397 pins = "gpio113"; 398 function = "gpio"; 399 400 drive-strength = <2>; 401 bias-disable; 402 }; 403 404 tp_int_default: tp-int-default-state { 405 pins = "gpio13"; 406 function = "gpio"; 407 408 drive-strength = <2>; 409 bias-disable; 410 }; 411}; 412