1/* 2 * Copyright (C) 2017 Jagan Teki <jteki@openedev.com> 3 * 4 * This file is dual-licensed: you can use it either under the terms 5 * of the GPL or the X11 license, at your option. Note that this dual 6 * licensing only applies to this file, and not this project as a 7 * whole. 8 * 9 * a) This file is free software; you can redistribute it and/or 10 * modify it under the terms of the GNU General Public License as 11 * published by the Free Software Foundation; either version 2 of the 12 * License, or (at your option) any later version. 13 * 14 * This file is distributed in the hope that it will be useful, 15 * but WITHOUT ANY WARRANTY; without even the implied warranty of 16 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 17 * GNU General Public License for more details. 18 * 19 * Or, alternatively, 20 * 21 * b) Permission is hereby granted, free of charge, to any person 22 * obtaining a copy of this software and associated documentation 23 * files (the "Software"), to deal in the Software without 24 * restriction, including without limitation the rights to use, 25 * copy, modify, merge, publish, distribute, sublicense, and/or 26 * sell copies of the Software, and to permit persons to whom the 27 * Software is furnished to do so, subject to the following 28 * conditions: 29 * 30 * The above copyright notice and this permission notice shall be 31 * included in all copies or substantial portions of the Software. 32 * 33 * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, 34 * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES 35 * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND 36 * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT 37 * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, 38 * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING 39 * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR 40 * OTHER DEALINGS IN THE SOFTWARE. 41 */ 42 43#include "sun8i-h3-nanopi.dtsi" 44 45/ { 46 model = "FriendlyArm NanoPi M1 Plus"; 47 compatible = "friendlyarm,nanopi-m1-plus", "allwinner,sun8i-h3"; 48 49 aliases { 50 serial1 = &uart3; 51 ethernet0 = &emac; 52 ethernet1 = &sdio_wifi; 53 }; 54 55 reg_gmac_3v3: gmac-3v3 { 56 compatible = "regulator-fixed"; 57 regulator-name = "gmac-3v3"; 58 regulator-min-microvolt = <3300000>; 59 regulator-max-microvolt = <3300000>; 60 startup-delay-us = <100000>; 61 enable-active-high; 62 gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>; 63 }; 64 65 wifi_pwrseq: pwrseq { 66 compatible = "mmc-pwrseq-simple"; 67 reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */ 68 }; 69 70 connector { 71 compatible = "hdmi-connector"; 72 type = "a"; 73 74 port { 75 hdmi_con_in: endpoint { 76 remote-endpoint = <&hdmi_out_con>; 77 }; 78 }; 79 }; 80}; 81 82&de { 83 status = "okay"; 84}; 85 86&ehci1 { 87 status = "okay"; 88}; 89 90&ehci2 { 91 status = "okay"; 92}; 93 94&emac { 95 pinctrl-names = "default"; 96 pinctrl-0 = <&emac_rgmii_pins>; 97 phy-supply = <®_gmac_3v3>; 98 phy-handle = <&ext_rgmii_phy>; 99 phy-mode = "rgmii"; 100 101 status = "okay"; 102}; 103 104&external_mdio { 105 ext_rgmii_phy: ethernet-phy@1 { 106 compatible = "ethernet-phy-ieee802.3-c22"; 107 reg = <7>; 108 }; 109}; 110 111&hdmi { 112 status = "okay"; 113}; 114 115&hdmi_out { 116 hdmi_out_con: endpoint { 117 remote-endpoint = <&hdmi_con_in>; 118 }; 119}; 120 121&ir { 122 pinctrl-names = "default"; 123 pinctrl-0 = <&r_ir_rx_pin>; 124 status = "okay"; 125}; 126 127&mmc1 { 128 vmmc-supply = <®_vcc3v3>; 129 vqmmc-supply = <®_vcc3v3>; 130 mmc-pwrseq = <&wifi_pwrseq>; 131 bus-width = <4>; 132 non-removable; 133 status = "okay"; 134 135 sdio_wifi: wifi@1 { 136 reg = <1>; 137 compatible = "brcm,bcm4329-fmac"; 138 interrupt-parent = <&pio>; 139 interrupts = <6 10 IRQ_TYPE_LEVEL_LOW>; /* PG10 / EINT10 */ 140 interrupt-names = "host-wake"; 141 }; 142}; 143 144&mmc2 { 145 pinctrl-names = "default"; 146 pinctrl-0 = <&mmc2_8bit_pins>; 147 vmmc-supply = <®_vcc3v3>; 148 vqmmc-supply = <®_vcc3v3>; 149 bus-width = <8>; 150 non-removable; 151 status = "okay"; 152}; 153 154&ohci1 { 155 status = "okay"; 156}; 157 158&ohci2 { 159 status = "okay"; 160}; 161 162&uart3 { 163 pinctrl-names = "default"; 164 pinctrl-0 = <&uart3_pins>, <&uart3_rts_cts_pins>; 165 status = "okay"; 166}; 167