xref: /linux/scripts/dtc/include-prefixes/arm/allwinner/sun8i-a83t-cubietruck-plus.dts (revision 621cde16e49b3ecf7d59a8106a20aaebfb4a59a9) 
1/*
2 * Copyright 2015 Chen-Yu Tsai
3 *
4 * Chen-Yu Tsai <wens@csie.org>
5 *
6 * This file is dual-licensed: you can use it either under the terms
7 * of the GPL or the X11 license, at your option. Note that this dual
8 * licensing only applies to this file, and not this project as a
9 * whole.
10 *
11 *  a) This file is free software; you can redistribute it and/or
12 *     modify it under the terms of the GNU General Public License as
13 *     published by the Free Software Foundation; either version 2 of the
14 *     License, or (at your option) any later version.
15 *
16 *     This file is distributed in the hope that it will be useful,
17 *     but WITHOUT ANY WARRANTY; without even the implied warranty of
18 *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
19 *     GNU General Public License for more details.
20 *
21 * Or, alternatively,
22 *
23 *  b) Permission is hereby granted, free of charge, to any person
24 *     obtaining a copy of this software and associated documentation
25 *     files (the "Software"), to deal in the Software without
26 *     restriction, including without limitation the rights to use,
27 *     copy, modify, merge, publish, distribute, sublicense, and/or
28 *     sell copies of the Software, and to permit persons to whom the
29 *     Software is furnished to do so, subject to the following
30 *     conditions:
31 *
32 *     The above copyright notice and this permission notice shall be
33 *     included in all copies or substantial portions of the Software.
34 *
35 *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
36 *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
37 *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
38 *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
39 *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
40 *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
41 *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
42 *     OTHER DEALINGS IN THE SOFTWARE.
43 */
44
45/dts-v1/;
46#include "sun8i-a83t.dtsi"
47
48#include <dt-bindings/gpio/gpio.h>
49
50/ {
51	model = "Cubietech Cubietruck Plus";
52	compatible = "cubietech,cubietruck-plus", "allwinner,sun8i-a83t";
53
54	aliases {
55		ethernet0 = &emac;
56		serial0 = &uart0;
57	};
58
59	chosen {
60		stdout-path = "serial0:115200n8";
61	};
62
63	hdmi-connector {
64		compatible = "hdmi-connector";
65		type = "a";
66
67		port {
68			hdmi_con_in: endpoint {
69				remote-endpoint = <&hdmi_out_con>;
70			};
71		};
72	};
73
74	leds {
75		compatible = "gpio-leds";
76
77		led-0 {
78			label = "cubietruck-plus:blue:usr";
79			gpios = <&pio 3 25 GPIO_ACTIVE_HIGH>; /* PD25 */
80		};
81
82		led-1 {
83			label = "cubietruck-plus:orange:usr";
84			gpios = <&pio 3 26 GPIO_ACTIVE_HIGH>; /* PD26 */
85		};
86
87		led-2 {
88			label = "cubietruck-plus:white:usr";
89			gpios = <&pio 3 27 GPIO_ACTIVE_HIGH>; /* PD27 */
90		};
91
92		led-3 {
93			label = "cubietruck-plus:green:usr";
94			gpios = <&pio 4 4 GPIO_ACTIVE_HIGH>; /* PE4 */
95		};
96	};
97
98	usb-hub {
99		/* I2C is not connected */
100		compatible = "smsc,usb3503";
101		initial-mode = <1>; /* initialize in HUB mode */
102		disabled-ports = <1>;
103		intn-gpios = <&pio 7 5 GPIO_ACTIVE_HIGH>; /* PH5 */
104		reset-gpios = <&pio 4 16 GPIO_ACTIVE_LOW>; /* PE16 */
105		connect-gpios = <&pio 4 17 GPIO_ACTIVE_HIGH>; /* PE17 */
106		refclk-frequency = <19200000>;
107	};
108
109	reg_usb1_vbus: reg-usb1-vbus {
110		compatible = "regulator-fixed";
111		regulator-name = "usb1-vbus";
112		regulator-min-microvolt = <5000000>;
113		regulator-max-microvolt = <5000000>;
114		regulator-boot-on;
115		enable-active-high;
116		gpio = <&pio 3 29 GPIO_ACTIVE_HIGH>; /* PD29 */
117	};
118
119	reg_usb2_vbus: reg-usb2-vbus {
120		compatible = "regulator-fixed";
121		regulator-name = "usb2-vbus";
122		regulator-min-microvolt = <5000000>;
123		regulator-max-microvolt = <5000000>;
124		regulator-boot-on;
125		enable-active-high;
126		gpio = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */
127	};
128
129	sound {
130		compatible = "simple-audio-card";
131		simple-audio-card,name = "On-board SPDIF";
132
133		simple-audio-card,cpu {
134			sound-dai = <&spdif>;
135		};
136
137		simple-audio-card,codec {
138			sound-dai = <&spdif_out>;
139		};
140	};
141
142	spdif_out: spdif-out {
143		#sound-dai-cells = <0>;
144		compatible = "linux,spdif-dit";
145	};
146
147	wifi_pwrseq: pwrseq {
148		compatible = "mmc-pwrseq-simple";
149		clocks = <&ac100_rtc 1>;
150		clock-names = "ext_clock";
151		/* The WiFi low power clock must be 32768 Hz */
152		assigned-clocks = <&ac100_rtc 1>;
153		assigned-clock-rates = <32768>;
154		/* enables internal regulator and de-asserts reset */
155		reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 WL-PMU-EN */
156	};
157};
158
159&cpu0 {
160	cpu-supply = <&reg_dcdc2>;
161};
162
163&cpu100 {
164	cpu-supply = <&reg_dcdc3>;
165};
166
167&de {
168	status = "okay";
169};
170
171&ehci0 {
172	/* GL830 USB-to-SATA bridge here */
173	status = "okay";
174};
175
176&ehci1 {
177	/* USB3503 HSIC USB 2.0 hub here */
178	status = "okay";
179};
180
181&emac {
182	pinctrl-names = "default";
183	pinctrl-0 = <&emac_rgmii_pins>;
184	phy-supply = <&reg_dldo4>;
185	phy-handle = <&rgmii_phy>;
186	phy-mode = "rgmii-id";
187	status = "okay";
188};
189
190&hdmi {
191	status = "okay";
192};
193
194&hdmi_out {
195	hdmi_out_con: endpoint {
196		remote-endpoint = <&hdmi_con_in>;
197	};
198};
199
200&mdio {
201	rgmii_phy: ethernet-phy@1 {
202		compatible = "ethernet-phy-ieee802.3-c22";
203		reg = <1>;
204	};
205};
206
207&mmc0 {
208	pinctrl-names = "default";
209	pinctrl-0 = <&mmc0_pins>;
210	vmmc-supply = <&reg_dcdc1>;
211	bus-width = <4>;
212	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
213	status = "okay";
214};
215
216&mmc1 {
217	vmmc-supply = <&reg_dcdc1>;
218	vqmmc-supply = <&reg_sw>;
219	mmc-pwrseq = <&wifi_pwrseq>;
220	bus-width = <4>;
221	non-removable;
222	status = "okay";
223};
224
225&mmc2 {
226	pinctrl-names = "default";
227	pinctrl-0 = <&mmc2_8bit_emmc_pins>;
228	vmmc-supply = <&reg_dcdc1>;
229	bus-width = <8>;
230	non-removable;
231	cap-mmc-hw-reset;
232	status = "okay";
233};
234
235&r_rsb {
236	status = "okay";
237
238	axp81x: pmic@3a3 {
239		compatible = "x-powers,axp818", "x-powers,axp813";
240		reg = <0x3a3>;
241		interrupt-parent = <&r_intc>;
242		interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>;
243		eldoin-supply = <&reg_dcdc1>;
244		swin-supply = <&reg_dcdc1>;
245		x-powers,drive-vbus-en;
246	};
247
248	ac100: codec@e89 {
249		compatible = "x-powers,ac100";
250		reg = <0xe89>;
251
252		ac100_codec: codec {
253			compatible = "x-powers,ac100-codec";
254			interrupt-parent = <&r_pio>;
255			interrupts = <0 11 IRQ_TYPE_LEVEL_LOW>; /* PL11 */
256			#clock-cells = <0>;
257			clock-output-names = "4M_adda";
258		};
259
260		ac100_rtc: rtc {
261			compatible = "x-powers,ac100-rtc";
262			interrupt-parent = <&r_intc>;
263			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>;
264			clocks = <&ac100_codec>;
265			#clock-cells = <1>;
266			clock-output-names = "cko1_rtc",
267					     "cko2_rtc",
268					     "cko3_rtc";
269		};
270	};
271};
272
273#include "axp81x.dtsi"
274
275&ac_power_supply {
276	status = "okay";
277};
278
279&battery_power_supply {
280	status = "okay";
281};
282
283&reg_aldo1 {
284	regulator-always-on;
285	regulator-min-microvolt = <1800000>;
286	regulator-max-microvolt = <1800000>;
287	regulator-name = "vcc-1v8";
288};
289
290&reg_aldo2 {
291	regulator-always-on;
292	regulator-min-microvolt = <1800000>;
293	regulator-max-microvolt = <1800000>;
294	regulator-name = "dram-pll";
295};
296
297&reg_aldo3 {
298	regulator-always-on;
299	regulator-min-microvolt = <3000000>;
300	regulator-max-microvolt = <3000000>;
301	regulator-name = "avcc";
302};
303
304&reg_dcdc1 {
305	/*
306	 * The schematics say this should be 3.3V, but the FEX file says
307	 * it should be 3V. The latter makes sense, as the WiFi module's
308	 * I/O is indirectly powered from DCDC1, through SW. It is rated
309	 * at 2.98V maximum.
310	 */
311	regulator-always-on;
312	regulator-min-microvolt = <3000000>;
313	regulator-max-microvolt = <3000000>;
314	regulator-name = "vcc-3v";
315};
316
317&reg_dcdc2 {
318	regulator-always-on;
319	regulator-min-microvolt = <700000>;
320	regulator-max-microvolt = <1100000>;
321	regulator-name = "vdd-cpua";
322};
323
324&reg_dcdc3 {
325	regulator-always-on;
326	regulator-min-microvolt = <700000>;
327	regulator-max-microvolt = <1100000>;
328	regulator-name = "vdd-cpub";
329};
330
331&reg_dcdc4 {
332	regulator-min-microvolt = <700000>;
333	regulator-max-microvolt = <1100000>;
334	regulator-name = "vdd-gpu";
335};
336
337&reg_dcdc5 {
338	regulator-always-on;
339	regulator-min-microvolt = <1500000>;
340	regulator-max-microvolt = <1500000>;
341	regulator-name = "vcc-dram";
342};
343
344&reg_dcdc6 {
345	regulator-always-on;
346	regulator-min-microvolt = <900000>;
347	regulator-max-microvolt = <900000>;
348	regulator-name = "vdd-sys";
349};
350
351&reg_dldo2 {
352	regulator-min-microvolt = <3300000>;
353	regulator-max-microvolt = <3300000>;
354	regulator-name = "dp-pwr";
355};
356
357&reg_dldo3 {
358	regulator-always-on;
359	regulator-min-microvolt = <2500000>;
360	regulator-max-microvolt = <2500000>;
361	regulator-name = "ephy-io";
362};
363
364&reg_dldo4 {
365	/*
366	 * The PHY requires 20ms after all voltages are applied until core
367	 * logic is ready and 30ms after the reset pin is de-asserted.
368	 * Set a 100ms delay to account for PMIC ramp time and board traces.
369	 */
370	regulator-enable-ramp-delay = <100000>;
371	regulator-min-microvolt = <3300000>;
372	regulator-max-microvolt = <3300000>;
373	regulator-name = "ephy";
374};
375
376&reg_drivevbus {
377	regulator-name = "usb0-vbus";
378	status = "okay";
379};
380
381&reg_eldo1 {
382	regulator-min-microvolt = <1200000>;
383	regulator-max-microvolt = <1200000>;
384	regulator-name = "dp-bridge-1";
385};
386
387&reg_eldo2 {
388	regulator-min-microvolt = <1200000>;
389	regulator-max-microvolt = <1200000>;
390	regulator-name = "dp-bridge-2";
391};
392
393&reg_fldo1 {
394	/* TODO should be handled by USB PHY */
395	regulator-always-on;
396	regulator-min-microvolt = <1080000>;
397	regulator-max-microvolt = <1320000>;
398	regulator-name = "vdd12-hsic";
399};
400
401&reg_fldo2 {
402	/*
403	 * Despite the embedded CPUs core not being used in any way,
404	 * this must remain on or the system will hang.
405	 */
406	regulator-always-on;
407	regulator-min-microvolt = <700000>;
408	regulator-max-microvolt = <1100000>;
409	regulator-name = "vdd-cpus";
410};
411
412&reg_rtc_ldo {
413	regulator-name = "vcc-rtc";
414};
415
416&reg_sw {
417	regulator-name = "vcc-wifi-io";
418};
419
420&spdif {
421	status = "okay";
422};
423
424&uart0 {
425	pinctrl-names = "default";
426	pinctrl-0 = <&uart0_pb_pins>;
427	status = "okay";
428};
429
430&uart1 {
431	pinctrl-names = "default";
432	pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
433	uart-has-rtscts;
434	status = "okay";
435
436	bluetooth {
437		compatible = "brcm,bcm4330-bt";
438		clocks = <&ac100_rtc 1>;
439		clock-names = "lpo";
440		vbat-supply = <&reg_dcdc1>;
441		vddio-supply = <&reg_sw>;
442		device-wakeup-gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PL10 */
443		host-wakeup-gpios = <&r_pio 0 8 GPIO_ACTIVE_HIGH>; /* PL8 */
444		shutdown-gpios = <&r_pio 0 4 GPIO_ACTIVE_HIGH>; /* PL4 */
445	};
446};
447
448&usb_otg {
449	dr_mode = "otg";
450	status = "okay";
451};
452
453&usb_power_supply {
454	status = "okay";
455};
456
457&usbphy {
458	usb0_id_det-gpios = <&pio 7 11 GPIO_ACTIVE_HIGH>; /* PH11 */
459	usb0_vbus_power-supply = <&usb_power_supply>;
460	usb0_vbus-supply = <&reg_drivevbus>;
461	usb1_vbus-supply = <&reg_usb1_vbus>;
462	usb2_vbus-supply = <&reg_usb2_vbus>;
463	status = "okay";
464};
465