1# 2# SPI driver configuration 3# 4# NOTE: the reason this doesn't show SPI slave support is mostly that 5# nobody's needed a slave side API yet. The master-role API is not 6# fully appropriate there, so it'd need some thought to do well. 7# 8menu "SPI support" 9 depends on HAS_IOMEM 10 11config SPI 12 bool "SPI support" 13 help 14 The "Serial Peripheral Interface" is a low level synchronous 15 protocol. Chips that support SPI can have data transfer rates 16 up to several tens of Mbit/sec. Chips are addressed with a 17 controller and a chipselect. Most SPI slaves don't support 18 dynamic device discovery; some are even write-only or read-only. 19 20 SPI is widely used by microcontrollers to talk with sensors, 21 eeprom and flash memory, codecs and various other controller 22 chips, analog to digital (and d-to-a) converters, and more. 23 MMC and SD cards can be accessed using SPI protocol; and for 24 DataFlash cards used in MMC sockets, SPI must always be used. 25 26 SPI is one of a family of similar protocols using a four wire 27 interface (select, clock, data in, data out) including Microwire 28 (half duplex), SSP, SSI, and PSP. This driver framework should 29 work with most such devices and controllers. 30 31config SPI_DEBUG 32 boolean "Debug support for SPI drivers" 33 depends on SPI && DEBUG_KERNEL 34 help 35 Say "yes" to enable debug messaging (like dev_dbg and pr_debug), 36 sysfs, and debugfs support in SPI controller and protocol drivers. 37 38# 39# MASTER side ... talking to discrete SPI slave chips including microcontrollers 40# 41 42config SPI_MASTER 43# boolean "SPI Master Support" 44 boolean 45 default SPI 46 help 47 If your system has an master-capable SPI controller (which 48 provides the clock and chipselect), you can enable that 49 controller and the protocol drivers for the SPI slave chips 50 that are connected. 51 52comment "SPI Master Controller Drivers" 53 depends on SPI_MASTER 54 55config SPI_ATMEL 56 tristate "Atmel SPI Controller" 57 depends on (ARCH_AT91 || AVR32) && SPI_MASTER 58 help 59 This selects a driver for the Atmel SPI Controller, present on 60 many AT32 (AVR32) and AT91 (ARM) chips. 61 62config SPI_BFIN 63 tristate "SPI controller driver for ADI Blackfin5xx" 64 depends on SPI_MASTER && BLACKFIN 65 help 66 This is the SPI controller master driver for Blackfin 5xx processor. 67 68config SPI_AU1550 69 tristate "Au1550/Au12x0 SPI Controller" 70 depends on SPI_MASTER && (SOC_AU1550 || SOC_AU1200) && EXPERIMENTAL 71 select SPI_BITBANG 72 help 73 If you say yes to this option, support will be included for the 74 Au1550 SPI controller (may also work with Au1200,Au1210,Au1250). 75 76 This driver can also be built as a module. If so, the module 77 will be called au1550_spi. 78 79config SPI_BITBANG 80 tristate "Bitbanging SPI master" 81 depends on SPI_MASTER && EXPERIMENTAL 82 help 83 With a few GPIO pins, your system can bitbang the SPI protocol. 84 Select this to get SPI support through I/O pins (GPIO, parallel 85 port, etc). Or, some systems' SPI master controller drivers use 86 this code to manage the per-word or per-transfer accesses to the 87 hardware shift registers. 88 89 This is library code, and is automatically selected by drivers that 90 need it. You only need to select this explicitly to support driver 91 modules that aren't part of this kernel tree. 92 93config SPI_BUTTERFLY 94 tristate "Parallel port adapter for AVR Butterfly (DEVELOPMENT)" 95 depends on SPI_MASTER && PARPORT && EXPERIMENTAL 96 select SPI_BITBANG 97 help 98 This uses a custom parallel port cable to connect to an AVR 99 Butterfly <http://www.atmel.com/products/avr/butterfly>, an 100 inexpensive battery powered microcontroller evaluation board. 101 This same cable can be used to flash new firmware. 102 103config SPI_IMX 104 tristate "Freescale iMX SPI controller" 105 depends on SPI_MASTER && ARCH_IMX && EXPERIMENTAL 106 help 107 This enables using the Freescale iMX SPI controller in master 108 mode. 109 110config SPI_LM70_LLP 111 tristate "Parallel port adapter for LM70 eval board (DEVELOPMENT)" 112 depends on SPI_MASTER && PARPORT && EXPERIMENTAL 113 select SPI_BITBANG 114 help 115 This driver supports the NS LM70 LLP Evaluation Board, 116 which interfaces to an LM70 temperature sensor using 117 a parallel port. 118 119config SPI_MPC52xx_PSC 120 tristate "Freescale MPC52xx PSC SPI controller" 121 depends on SPI_MASTER && PPC_MPC52xx && EXPERIMENTAL 122 help 123 This enables using the Freescale MPC52xx Programmable Serial 124 Controller in master SPI mode. 125 126config SPI_MPC83xx 127 tristate "Freescale MPC83xx/QUICC Engine SPI controller" 128 depends on SPI_MASTER && (PPC_83xx || QUICC_ENGINE) && EXPERIMENTAL 129 select SPI_BITBANG 130 help 131 This enables using the Freescale MPC83xx and QUICC Engine SPI 132 controllers in master mode. 133 134 Note, this driver uniquely supports the SPI controller on the MPC83xx 135 family of PowerPC processors, plus processors with QUICC Engine 136 technology. This driver uses a simple set of shift registers for data 137 (opposed to the CPM based descriptor model). 138 139config SPI_OMAP_UWIRE 140 tristate "OMAP1 MicroWire" 141 depends on SPI_MASTER && ARCH_OMAP1 142 select SPI_BITBANG 143 help 144 This hooks up to the MicroWire controller on OMAP1 chips. 145 146config SPI_OMAP24XX 147 tristate "McSPI driver for OMAP24xx/OMAP34xx" 148 depends on SPI_MASTER && (ARCH_OMAP24XX || ARCH_OMAP34XX) 149 help 150 SPI master controller for OMAP24xx/OMAP34xx Multichannel SPI 151 (McSPI) modules. 152 153config SPI_PXA2XX 154 tristate "PXA2xx SSP SPI master" 155 depends on SPI_MASTER && ARCH_PXA && EXPERIMENTAL 156 select PXA_SSP 157 help 158 This enables using a PXA2xx SSP port as a SPI master controller. 159 The driver can be configured to use any SSP port and additional 160 documentation can be found a Documentation/spi/pxa2xx. 161 162config SPI_S3C24XX 163 tristate "Samsung S3C24XX series SPI" 164 depends on SPI_MASTER && ARCH_S3C2410 && EXPERIMENTAL 165 select SPI_BITBANG 166 help 167 SPI driver for Samsung S3C24XX series ARM SoCs 168 169config SPI_S3C24XX_GPIO 170 tristate "Samsung S3C24XX series SPI by GPIO" 171 depends on SPI_MASTER && ARCH_S3C2410 && EXPERIMENTAL 172 select SPI_BITBANG 173 help 174 SPI driver for Samsung S3C24XX series ARM SoCs using 175 GPIO lines to provide the SPI bus. This can be used where 176 the inbuilt hardware cannot provide the transfer mode, or 177 where the board is using non hardware connected pins. 178 179config SPI_SH_SCI 180 tristate "SuperH SCI SPI controller" 181 depends on SPI_MASTER && SUPERH 182 select SPI_BITBANG 183 help 184 SPI driver for SuperH SCI blocks. 185 186config SPI_TXX9 187 tristate "Toshiba TXx9 SPI controller" 188 depends on SPI_MASTER && GENERIC_GPIO && CPU_TX49XX 189 help 190 SPI driver for Toshiba TXx9 MIPS SoCs 191 192config SPI_XILINX 193 tristate "Xilinx SPI controller" 194 depends on SPI_MASTER && XILINX_VIRTEX && EXPERIMENTAL 195 select SPI_BITBANG 196 help 197 This exposes the SPI controller IP from the Xilinx EDK. 198 199 See the "OPB Serial Peripheral Interface (SPI) (v1.00e)" 200 Product Specification document (DS464) for hardware details. 201 202# 203# Add new SPI master controllers in alphabetical order above this line 204# 205 206# 207# There are lots of SPI device types, with sensors and memory 208# being probably the most widely used ones. 209# 210comment "SPI Protocol Masters" 211 depends on SPI_MASTER 212 213config SPI_AT25 214 tristate "SPI EEPROMs from most vendors" 215 depends on SPI_MASTER && SYSFS 216 help 217 Enable this driver to get read/write support to most SPI EEPROMs, 218 after you configure the board init code to know about each eeprom 219 on your target board. 220 221 This driver can also be built as a module. If so, the module 222 will be called at25. 223 224config SPI_SPIDEV 225 tristate "User mode SPI device driver support" 226 depends on SPI_MASTER && EXPERIMENTAL 227 help 228 This supports user mode SPI protocol drivers. 229 230 Note that this application programming interface is EXPERIMENTAL 231 and hence SUBJECT TO CHANGE WITHOUT NOTICE while it stabilizes. 232 233config SPI_TLE62X0 234 tristate "Infineon TLE62X0 (for power switching)" 235 depends on SPI_MASTER && SYSFS 236 help 237 SPI driver for Infineon TLE62X0 series line driver chips, 238 such as the TLE6220, TLE6230 and TLE6240. This provides a 239 sysfs interface, with each line presented as a kind of GPIO 240 exposing both switch control and diagnostic feedback. 241 242# 243# Add new SPI protocol masters in alphabetical order above this line 244# 245 246# (slave support would go here) 247 248endmenu # "SPI support" 249 250