1 // SPDX-License-Identifier: GPL-2.0-or-later 2 /* 3 * Copyright (c) 2014-2015 Hisilicon Limited. 4 */ 5 6 #include <linux/acpi.h> 7 #include <linux/errno.h> 8 #include <linux/etherdevice.h> 9 #include <linux/init.h> 10 #include <linux/kernel.h> 11 #include <linux/mfd/syscon.h> 12 #include <linux/module.h> 13 #include <linux/mutex.h> 14 #include <linux/netdevice.h> 15 #include <linux/of_address.h> 16 #include <linux/of.h> 17 #include <linux/of_mdio.h> 18 #include <linux/of_platform.h> 19 #include <linux/phy.h> 20 #include <linux/platform_device.h> 21 #include <linux/regmap.h> 22 23 #define MDIO_DRV_NAME "Hi-HNS_MDIO" 24 #define MDIO_BUS_NAME "Hisilicon MII Bus" 25 26 #define MDIO_TIMEOUT 1000000 27 28 struct hns_mdio_sc_reg { 29 u16 mdio_clk_en; 30 u16 mdio_clk_dis; 31 u16 mdio_reset_req; 32 u16 mdio_reset_dreq; 33 u16 mdio_clk_st; 34 u16 mdio_reset_st; 35 }; 36 37 struct hns_mdio_device { 38 u8 __iomem *vbase; /* mdio reg base address */ 39 struct regmap *subctrl_vbase; 40 struct hns_mdio_sc_reg sc_reg; 41 }; 42 43 /* mdio reg */ 44 #define MDIO_COMMAND_REG 0x0 45 #define MDIO_ADDR_REG 0x4 46 #define MDIO_WDATA_REG 0x8 47 #define MDIO_RDATA_REG 0xc 48 #define MDIO_STA_REG 0x10 49 50 /* cfg phy bit map */ 51 #define MDIO_CMD_DEVAD_M 0x1f 52 #define MDIO_CMD_DEVAD_S 0 53 #define MDIO_CMD_PRTAD_M 0x1f 54 #define MDIO_CMD_PRTAD_S 5 55 #define MDIO_CMD_OP_S 10 56 #define MDIO_CMD_ST_S 12 57 #define MDIO_CMD_START_B 14 58 59 #define MDIO_ADDR_DATA_M 0xffff 60 #define MDIO_ADDR_DATA_S 0 61 62 #define MDIO_WDATA_DATA_M 0xffff 63 #define MDIO_WDATA_DATA_S 0 64 65 #define MDIO_RDATA_DATA_M 0xffff 66 #define MDIO_RDATA_DATA_S 0 67 68 #define MDIO_STATE_STA_B 0 69 70 enum mdio_st_clause { 71 MDIO_ST_CLAUSE_45 = 0, 72 MDIO_ST_CLAUSE_22 73 }; 74 75 enum mdio_c22_op_seq { 76 MDIO_C22_WRITE = 1, 77 MDIO_C22_READ = 2 78 }; 79 80 enum mdio_c45_op_seq { 81 MDIO_C45_WRITE_ADDR = 0, 82 MDIO_C45_WRITE_DATA, 83 MDIO_C45_READ_INCREMENT, 84 MDIO_C45_READ 85 }; 86 87 /* peri subctrl reg */ 88 #define MDIO_SC_CLK_EN 0x338 89 #define MDIO_SC_CLK_DIS 0x33C 90 #define MDIO_SC_RESET_REQ 0xA38 91 #define MDIO_SC_RESET_DREQ 0xA3C 92 #define MDIO_SC_CLK_ST 0x531C 93 #define MDIO_SC_RESET_ST 0x5A1C 94 95 static void mdio_write_reg(u8 __iomem *base, u32 reg, u32 value) 96 { 97 writel_relaxed(value, base + reg); 98 } 99 100 #define MDIO_WRITE_REG(a, reg, value) \ 101 mdio_write_reg((a)->vbase, (reg), (value)) 102 103 static u32 mdio_read_reg(u8 __iomem *base, u32 reg) 104 { 105 return readl_relaxed(base + reg); 106 } 107 108 #define mdio_set_field(origin, mask, shift, val) \ 109 do { \ 110 (origin) &= (~((mask) << (shift))); \ 111 (origin) |= (((val) & (mask)) << (shift)); \ 112 } while (0) 113 114 #define mdio_get_field(origin, mask, shift) (((origin) >> (shift)) & (mask)) 115 116 static void mdio_set_reg_field(u8 __iomem *base, u32 reg, u32 mask, u32 shift, 117 u32 val) 118 { 119 u32 origin = mdio_read_reg(base, reg); 120 121 mdio_set_field(origin, mask, shift, val); 122 mdio_write_reg(base, reg, origin); 123 } 124 125 #define MDIO_SET_REG_FIELD(dev, reg, mask, shift, val) \ 126 mdio_set_reg_field((dev)->vbase, (reg), (mask), (shift), (val)) 127 128 static u32 mdio_get_reg_field(u8 __iomem *base, u32 reg, u32 mask, u32 shift) 129 { 130 u32 origin; 131 132 origin = mdio_read_reg(base, reg); 133 return mdio_get_field(origin, mask, shift); 134 } 135 136 #define MDIO_GET_REG_FIELD(dev, reg, mask, shift) \ 137 mdio_get_reg_field((dev)->vbase, (reg), (mask), (shift)) 138 139 #define MDIO_GET_REG_BIT(dev, reg, bit) \ 140 mdio_get_reg_field((dev)->vbase, (reg), 0x1ull, (bit)) 141 142 #define MDIO_CHECK_SET_ST 1 143 #define MDIO_CHECK_CLR_ST 0 144 145 static int mdio_sc_cfg_reg_write(struct hns_mdio_device *mdio_dev, 146 u32 cfg_reg, u32 set_val, 147 u32 st_reg, u32 st_msk, u8 check_st) 148 { 149 u32 time_cnt; 150 u32 reg_value; 151 int ret; 152 153 regmap_write(mdio_dev->subctrl_vbase, cfg_reg, set_val); 154 155 for (time_cnt = MDIO_TIMEOUT; time_cnt; time_cnt--) { 156 ret = regmap_read(mdio_dev->subctrl_vbase, st_reg, ®_value); 157 if (ret) 158 return ret; 159 160 reg_value &= st_msk; 161 if ((!!check_st) == (!!reg_value)) 162 break; 163 } 164 165 if ((!!check_st) != (!!reg_value)) 166 return -EBUSY; 167 168 return 0; 169 } 170 171 static int hns_mdio_wait_ready(struct mii_bus *bus) 172 { 173 struct hns_mdio_device *mdio_dev = bus->priv; 174 u32 cmd_reg_value; 175 int i; 176 177 /* waiting for MDIO_COMMAND_REG's mdio_start==0 */ 178 /* after that can do read or write*/ 179 for (i = 0; i < MDIO_TIMEOUT; i++) { 180 cmd_reg_value = MDIO_GET_REG_BIT(mdio_dev, 181 MDIO_COMMAND_REG, 182 MDIO_CMD_START_B); 183 if (!cmd_reg_value) 184 break; 185 } 186 if ((i == MDIO_TIMEOUT) && cmd_reg_value) 187 return -ETIMEDOUT; 188 189 return 0; 190 } 191 192 static void hns_mdio_cmd_write(struct hns_mdio_device *mdio_dev, 193 u8 is_c45, u8 op, u8 phy_id, u16 cmd) 194 { 195 u32 cmd_reg_value; 196 u8 st = is_c45 ? MDIO_ST_CLAUSE_45 : MDIO_ST_CLAUSE_22; 197 198 cmd_reg_value = st << MDIO_CMD_ST_S; 199 cmd_reg_value |= op << MDIO_CMD_OP_S; 200 cmd_reg_value |= 201 (phy_id & MDIO_CMD_PRTAD_M) << MDIO_CMD_PRTAD_S; 202 cmd_reg_value |= (cmd & MDIO_CMD_DEVAD_M) << MDIO_CMD_DEVAD_S; 203 cmd_reg_value |= 1 << MDIO_CMD_START_B; 204 205 MDIO_WRITE_REG(mdio_dev, MDIO_COMMAND_REG, cmd_reg_value); 206 } 207 208 /** 209 * hns_mdio_write_c22 - access phy register 210 * @bus: mdio bus 211 * @phy_id: phy id 212 * @regnum: register num 213 * @data: register value 214 * 215 * Return 0 on success, negative on failure 216 */ 217 static int hns_mdio_write_c22(struct mii_bus *bus, 218 int phy_id, int regnum, u16 data) 219 { 220 struct hns_mdio_device *mdio_dev = bus->priv; 221 u16 reg = (u16)(regnum & 0xffff); 222 u16 cmd_reg_cfg; 223 int ret; 224 u8 op; 225 226 dev_dbg(&bus->dev, "mdio write %s,base is %p\n", 227 bus->id, mdio_dev->vbase); 228 dev_dbg(&bus->dev, "phy id=%d, reg=%#x, write data=%d\n", 229 phy_id, reg, data); 230 231 /* wait for ready */ 232 ret = hns_mdio_wait_ready(bus); 233 if (ret) { 234 dev_err(&bus->dev, "MDIO bus is busy\n"); 235 return ret; 236 } 237 238 cmd_reg_cfg = reg; 239 op = MDIO_C22_WRITE; 240 241 MDIO_SET_REG_FIELD(mdio_dev, MDIO_WDATA_REG, MDIO_WDATA_DATA_M, 242 MDIO_WDATA_DATA_S, data); 243 244 hns_mdio_cmd_write(mdio_dev, false, op, phy_id, cmd_reg_cfg); 245 246 return 0; 247 } 248 249 /** 250 * hns_mdio_write_c45 - access phy register 251 * @bus: mdio bus 252 * @phy_id: phy id 253 * @devad: device address to read 254 * @regnum: register num 255 * @data: register value 256 * 257 * Return 0 on success, negative on failure 258 */ 259 static int hns_mdio_write_c45(struct mii_bus *bus, int phy_id, int devad, 260 int regnum, u16 data) 261 { 262 struct hns_mdio_device *mdio_dev = bus->priv; 263 u16 reg = (u16)(regnum & 0xffff); 264 u16 cmd_reg_cfg; 265 int ret; 266 u8 op; 267 268 dev_dbg(&bus->dev, "mdio write %s,base is %p\n", 269 bus->id, mdio_dev->vbase); 270 dev_dbg(&bus->dev, "phy id=%d, devad=%d, reg=%#x, write data=%d\n", 271 phy_id, devad, reg, data); 272 273 /* wait for ready */ 274 ret = hns_mdio_wait_ready(bus); 275 if (ret) { 276 dev_err(&bus->dev, "MDIO bus is busy\n"); 277 return ret; 278 } 279 280 /* config the cmd-reg to write addr*/ 281 MDIO_SET_REG_FIELD(mdio_dev, MDIO_ADDR_REG, MDIO_ADDR_DATA_M, 282 MDIO_ADDR_DATA_S, reg); 283 284 hns_mdio_cmd_write(mdio_dev, true, MDIO_C45_WRITE_ADDR, phy_id, devad); 285 286 /* check for read or write opt is finished */ 287 ret = hns_mdio_wait_ready(bus); 288 if (ret) { 289 dev_err(&bus->dev, "MDIO bus is busy\n"); 290 return ret; 291 } 292 293 /* config the data needed writing */ 294 cmd_reg_cfg = devad; 295 op = MDIO_C45_WRITE_DATA; 296 297 MDIO_SET_REG_FIELD(mdio_dev, MDIO_WDATA_REG, MDIO_WDATA_DATA_M, 298 MDIO_WDATA_DATA_S, data); 299 300 hns_mdio_cmd_write(mdio_dev, true, op, phy_id, cmd_reg_cfg); 301 302 return 0; 303 } 304 305 /** 306 * hns_mdio_read_c22 - access phy register 307 * @bus: mdio bus 308 * @phy_id: phy id 309 * @regnum: register num 310 * 311 * Return phy register value 312 */ 313 static int hns_mdio_read_c22(struct mii_bus *bus, int phy_id, int regnum) 314 { 315 struct hns_mdio_device *mdio_dev = bus->priv; 316 u16 reg = (u16)(regnum & 0xffff); 317 u16 reg_val; 318 int ret; 319 320 dev_dbg(&bus->dev, "mdio read %s,base is %p\n", 321 bus->id, mdio_dev->vbase); 322 dev_dbg(&bus->dev, "phy id=%d, reg=%#x!\n", phy_id, reg); 323 324 /* Step 1: wait for ready */ 325 ret = hns_mdio_wait_ready(bus); 326 if (ret) { 327 dev_err(&bus->dev, "MDIO bus is busy\n"); 328 return ret; 329 } 330 331 hns_mdio_cmd_write(mdio_dev, false, MDIO_C22_READ, phy_id, reg); 332 333 /* Step 2: waiting for MDIO_COMMAND_REG 's mdio_start==0,*/ 334 /* check for read or write opt is finished */ 335 ret = hns_mdio_wait_ready(bus); 336 if (ret) { 337 dev_err(&bus->dev, "MDIO bus is busy\n"); 338 return ret; 339 } 340 341 reg_val = MDIO_GET_REG_BIT(mdio_dev, MDIO_STA_REG, MDIO_STATE_STA_B); 342 if (reg_val) { 343 dev_err(&bus->dev, " ERROR! MDIO Read failed!\n"); 344 return -EBUSY; 345 } 346 347 /* Step 3; get out data*/ 348 reg_val = (u16)MDIO_GET_REG_FIELD(mdio_dev, MDIO_RDATA_REG, 349 MDIO_RDATA_DATA_M, MDIO_RDATA_DATA_S); 350 351 return reg_val; 352 } 353 354 /** 355 * hns_mdio_read_c45 - access phy register 356 * @bus: mdio bus 357 * @phy_id: phy id 358 * @devad: device address to read 359 * @regnum: register num 360 * 361 * Return phy register value 362 */ 363 static int hns_mdio_read_c45(struct mii_bus *bus, int phy_id, int devad, 364 int regnum) 365 { 366 struct hns_mdio_device *mdio_dev = bus->priv; 367 u16 reg = (u16)(regnum & 0xffff); 368 u16 reg_val; 369 int ret; 370 371 dev_dbg(&bus->dev, "mdio read %s,base is %p\n", 372 bus->id, mdio_dev->vbase); 373 dev_dbg(&bus->dev, "phy id=%d, devad=%d, reg=%#x!\n", 374 phy_id, devad, reg); 375 376 /* Step 1: wait for ready */ 377 ret = hns_mdio_wait_ready(bus); 378 if (ret) { 379 dev_err(&bus->dev, "MDIO bus is busy\n"); 380 return ret; 381 } 382 383 MDIO_SET_REG_FIELD(mdio_dev, MDIO_ADDR_REG, MDIO_ADDR_DATA_M, 384 MDIO_ADDR_DATA_S, reg); 385 386 /* Step 2; config the cmd-reg to write addr*/ 387 hns_mdio_cmd_write(mdio_dev, true, MDIO_C45_WRITE_ADDR, phy_id, devad); 388 389 /* Step 3: check for read or write opt is finished */ 390 ret = hns_mdio_wait_ready(bus); 391 if (ret) { 392 dev_err(&bus->dev, "MDIO bus is busy\n"); 393 return ret; 394 } 395 396 hns_mdio_cmd_write(mdio_dev, true, MDIO_C45_READ, phy_id, devad); 397 398 /* Step 5: waiting for MDIO_COMMAND_REG 's mdio_start==0,*/ 399 /* check for read or write opt is finished */ 400 ret = hns_mdio_wait_ready(bus); 401 if (ret) { 402 dev_err(&bus->dev, "MDIO bus is busy\n"); 403 return ret; 404 } 405 406 reg_val = MDIO_GET_REG_BIT(mdio_dev, MDIO_STA_REG, MDIO_STATE_STA_B); 407 if (reg_val) { 408 dev_err(&bus->dev, " ERROR! MDIO Read failed!\n"); 409 return -EBUSY; 410 } 411 412 /* Step 6; get out data*/ 413 reg_val = (u16)MDIO_GET_REG_FIELD(mdio_dev, MDIO_RDATA_REG, 414 MDIO_RDATA_DATA_M, MDIO_RDATA_DATA_S); 415 416 return reg_val; 417 } 418 419 /** 420 * hns_mdio_reset - reset mdio bus 421 * @bus: mdio bus 422 * 423 * Return 0 on success, negative on failure 424 */ 425 static int hns_mdio_reset(struct mii_bus *bus) 426 { 427 struct hns_mdio_device *mdio_dev = bus->priv; 428 const struct hns_mdio_sc_reg *sc_reg; 429 int ret; 430 431 if (dev_of_node(bus->parent)) { 432 if (!mdio_dev->subctrl_vbase) { 433 dev_err(&bus->dev, "mdio sys ctl reg has not mapped\n"); 434 return -ENODEV; 435 } 436 437 sc_reg = &mdio_dev->sc_reg; 438 /* 1. reset req, and read reset st check */ 439 ret = mdio_sc_cfg_reg_write(mdio_dev, sc_reg->mdio_reset_req, 440 0x1, sc_reg->mdio_reset_st, 0x1, 441 MDIO_CHECK_SET_ST); 442 if (ret) { 443 dev_err(&bus->dev, "MDIO reset fail\n"); 444 return ret; 445 } 446 447 /* 2. dis clk, and read clk st check */ 448 ret = mdio_sc_cfg_reg_write(mdio_dev, sc_reg->mdio_clk_dis, 449 0x1, sc_reg->mdio_clk_st, 0x1, 450 MDIO_CHECK_CLR_ST); 451 if (ret) { 452 dev_err(&bus->dev, "MDIO dis clk fail\n"); 453 return ret; 454 } 455 456 /* 3. reset dreq, and read reset st check */ 457 ret = mdio_sc_cfg_reg_write(mdio_dev, sc_reg->mdio_reset_dreq, 458 0x1, sc_reg->mdio_reset_st, 0x1, 459 MDIO_CHECK_CLR_ST); 460 if (ret) { 461 dev_err(&bus->dev, "MDIO dis clk fail\n"); 462 return ret; 463 } 464 465 /* 4. en clk, and read clk st check */ 466 ret = mdio_sc_cfg_reg_write(mdio_dev, sc_reg->mdio_clk_en, 467 0x1, sc_reg->mdio_clk_st, 0x1, 468 MDIO_CHECK_SET_ST); 469 if (ret) 470 dev_err(&bus->dev, "MDIO en clk fail\n"); 471 } else if (is_acpi_node(bus->parent->fwnode)) { 472 acpi_status s; 473 474 s = acpi_evaluate_object(ACPI_HANDLE(bus->parent), 475 "_RST", NULL, NULL); 476 if (ACPI_FAILURE(s)) { 477 dev_err(&bus->dev, "Reset failed, return:%#x\n", s); 478 ret = -EBUSY; 479 } else { 480 ret = 0; 481 } 482 } else { 483 dev_err(&bus->dev, "Can not get cfg data from DT or ACPI\n"); 484 ret = -ENXIO; 485 } 486 return ret; 487 } 488 489 /** 490 * hns_mdio_probe - probe mdio device 491 * @pdev: mdio platform device 492 * 493 * Return 0 on success, negative on failure 494 */ 495 static int hns_mdio_probe(struct platform_device *pdev) 496 { 497 struct hns_mdio_device *mdio_dev; 498 struct mii_bus *new_bus; 499 int ret; 500 501 if (!pdev) { 502 dev_err(NULL, "pdev is NULL!\r\n"); 503 return -ENODEV; 504 } 505 506 mdio_dev = devm_kzalloc(&pdev->dev, sizeof(*mdio_dev), GFP_KERNEL); 507 if (!mdio_dev) 508 return -ENOMEM; 509 510 new_bus = devm_mdiobus_alloc(&pdev->dev); 511 if (!new_bus) { 512 dev_err(&pdev->dev, "mdiobus_alloc fail!\n"); 513 return -ENOMEM; 514 } 515 516 new_bus->name = MDIO_BUS_NAME; 517 new_bus->read = hns_mdio_read_c22; 518 new_bus->write = hns_mdio_write_c22; 519 new_bus->read_c45 = hns_mdio_read_c45; 520 new_bus->write_c45 = hns_mdio_write_c45; 521 new_bus->reset = hns_mdio_reset; 522 new_bus->priv = mdio_dev; 523 new_bus->parent = &pdev->dev; 524 525 mdio_dev->vbase = devm_platform_ioremap_resource(pdev, 0); 526 if (IS_ERR(mdio_dev->vbase)) { 527 ret = PTR_ERR(mdio_dev->vbase); 528 return ret; 529 } 530 531 platform_set_drvdata(pdev, new_bus); 532 snprintf(new_bus->id, MII_BUS_ID_SIZE, "%s-%s", "Mii", 533 dev_name(&pdev->dev)); 534 if (dev_of_node(&pdev->dev)) { 535 struct of_phandle_args reg_args; 536 537 ret = of_parse_phandle_with_fixed_args(pdev->dev.of_node, 538 "subctrl-vbase", 539 4, 540 0, 541 ®_args); 542 if (!ret) { 543 mdio_dev->subctrl_vbase = 544 syscon_node_to_regmap(reg_args.np); 545 if (IS_ERR(mdio_dev->subctrl_vbase)) { 546 dev_warn(&pdev->dev, "syscon_node_to_regmap error\n"); 547 mdio_dev->subctrl_vbase = NULL; 548 } else { 549 if (reg_args.args_count == 4) { 550 mdio_dev->sc_reg.mdio_clk_en = 551 (u16)reg_args.args[0]; 552 mdio_dev->sc_reg.mdio_clk_dis = 553 (u16)reg_args.args[0] + 4; 554 mdio_dev->sc_reg.mdio_reset_req = 555 (u16)reg_args.args[1]; 556 mdio_dev->sc_reg.mdio_reset_dreq = 557 (u16)reg_args.args[1] + 4; 558 mdio_dev->sc_reg.mdio_clk_st = 559 (u16)reg_args.args[2]; 560 mdio_dev->sc_reg.mdio_reset_st = 561 (u16)reg_args.args[3]; 562 } else { 563 /* for compatible */ 564 mdio_dev->sc_reg.mdio_clk_en = 565 MDIO_SC_CLK_EN; 566 mdio_dev->sc_reg.mdio_clk_dis = 567 MDIO_SC_CLK_DIS; 568 mdio_dev->sc_reg.mdio_reset_req = 569 MDIO_SC_RESET_REQ; 570 mdio_dev->sc_reg.mdio_reset_dreq = 571 MDIO_SC_RESET_DREQ; 572 mdio_dev->sc_reg.mdio_clk_st = 573 MDIO_SC_CLK_ST; 574 mdio_dev->sc_reg.mdio_reset_st = 575 MDIO_SC_RESET_ST; 576 } 577 } 578 of_node_put(reg_args.np); 579 } else { 580 dev_warn(&pdev->dev, "find syscon ret = %#x\n", ret); 581 mdio_dev->subctrl_vbase = NULL; 582 } 583 584 ret = of_mdiobus_register(new_bus, pdev->dev.of_node); 585 } else if (is_acpi_node(pdev->dev.fwnode)) { 586 /* Clear all the IRQ properties */ 587 memset(new_bus->irq, PHY_POLL, 4 * PHY_MAX_ADDR); 588 589 /* Mask out all PHYs from auto probing. */ 590 new_bus->phy_mask = ~0; 591 592 /* Register the MDIO bus */ 593 ret = mdiobus_register(new_bus); 594 } else { 595 dev_err(&pdev->dev, "Can not get cfg data from DT or ACPI\n"); 596 ret = -ENXIO; 597 } 598 599 if (ret) { 600 dev_err(&pdev->dev, "Cannot register as MDIO bus!\n"); 601 platform_set_drvdata(pdev, NULL); 602 return ret; 603 } 604 605 return 0; 606 } 607 608 /** 609 * hns_mdio_remove - remove mdio device 610 * @pdev: mdio platform device 611 * 612 * Return 0 on success, negative on failure 613 */ 614 static void hns_mdio_remove(struct platform_device *pdev) 615 { 616 struct mii_bus *bus; 617 618 bus = platform_get_drvdata(pdev); 619 620 mdiobus_unregister(bus); 621 platform_set_drvdata(pdev, NULL); 622 } 623 624 static const struct of_device_id hns_mdio_match[] = { 625 {.compatible = "hisilicon,mdio"}, 626 {.compatible = "hisilicon,hns-mdio"}, 627 {} 628 }; 629 MODULE_DEVICE_TABLE(of, hns_mdio_match); 630 631 static const struct acpi_device_id hns_mdio_acpi_match[] = { 632 { "HISI0141", 0 }, 633 { }, 634 }; 635 MODULE_DEVICE_TABLE(acpi, hns_mdio_acpi_match); 636 637 static struct platform_driver hns_mdio_driver = { 638 .probe = hns_mdio_probe, 639 .remove_new = hns_mdio_remove, 640 .driver = { 641 .name = MDIO_DRV_NAME, 642 .of_match_table = hns_mdio_match, 643 .acpi_match_table = ACPI_PTR(hns_mdio_acpi_match), 644 }, 645 }; 646 647 module_platform_driver(hns_mdio_driver); 648 649 MODULE_LICENSE("GPL"); 650 MODULE_AUTHOR("Huawei Tech. Co., Ltd."); 651 MODULE_DESCRIPTION("Hisilicon HNS MDIO driver"); 652 MODULE_ALIAS("platform:" MDIO_DRV_NAME); 653