xref: /linux/arch/arm64/boot/dts/ti/k3-am62p5-var-som.dtsi (revision 4f38da1f027ea2c9f01bb71daa7a299c191b6940)

// SPDX-License-Identifier: GPL-2.0
/*
 * Common dtsi for Variscite VAR-SOM-AM62P
 *
 * Link: https://www.variscite.com/product/system-on-module-som/cortex-a53-krait/var-som-am62p-ti-sitara-am62px/
 *
 * Copyright (C) 2025 Variscite Ltd. - https://www.variscite.com/
 *
 */

/dts-v1/;

#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/leds/common.h>
#include <dt-bindings/pwm/pwm.h>
#include "k3-am62p5.dtsi"

/ {
	compatible = "variscite,var-som-am62p", "ti,am62p5";

	wifi_pwrseq: wifi-pwrseq {
		compatible = "mmc-pwrseq-simple";
		post-power-on-delay-ms = <100>;
		power-off-delay-us = <10000>;
		reset-gpios = <&main_gpio0 54 GPIO_ACTIVE_LOW>,	/* WIFI_PWR_EN */
			      <&main_gpio0 59 GPIO_ACTIVE_LOW>;	/* WIFI_EN */
	};

	mmc_pwrseq: mmc-pwrseq {
		compatible = "mmc-pwrseq-emmc";
		pinctrl-names = "default";
		pinctrl-0 = <&pinctrl_mmc_pwrseq>;
		reset-gpios = <&main_gpio0 49 GPIO_ACTIVE_LOW>;
	};

	memory@80000000 {
		/* 8G RAM */
		reg = <0x00000000 0x80000000 0x00000000 0x80000000>,
		      <0x00000008 0x80000000 0x00000001 0x80000000>;
		device_type = "memory";
		bootph-pre-ram;
	};

	opp-table {
		/* Add 1.4GHz OPP for am62p5-sk board. Requires VDD_CORE at 0v85 */
		opp-1400000000 {
			opp-hz = /bits/ 64 <1400000000>;
			opp-supported-hw = <0x01 0x0004>;
			clock-latency-ns = <6000000>;
		};
	};

	reserved_memory: reserved-memory {
		#address-cells = <2>;
		#size-cells = <2>;
		ranges;

		rtos_ipc_memory_region: rtos-ipc-memory@9b500000 {
			compatible = "shared-dma-pool";
			reg = <0x00 0x9b500000 0x00 0x00300000>;
			no-map;
		};

		mcu_r5fss0_core0_dma_memory_region: mcu-r5fss-dma-memory-region@9b800000 {
			compatible = "shared-dma-pool";
			reg = <0x00 0x9b800000 0x00 0x00100000>;
			no-map;
		};

		mcu_r5fss0_core0_memory_region: mcu-r5fss-memory-region@9b900000 {
			compatible = "shared-dma-pool";
			reg = <0x00 0x9b900000 0x00 0x00f00000>;
			no-map;
		};

		wkup_r5fss0_core0_dma_memory_region: r5f-dma-memory@9c800000 {
			compatible = "shared-dma-pool";
			reg = <0x00 0x9c800000 0x00 0x00100000>;
			no-map;
		};

		wkup_r5fss0_core0_memory_region: r5f-memory@9c900000 {
			compatible = "shared-dma-pool";
			reg = <0x00 0x9c900000 0x00 0x01e00000>;
			no-map;
		};

		secure_tfa_ddr: tfa@9e780000 {
			reg = <0x00 0x9e780000 0x00 0x80000>;
			no-map;
		};

		secure_ddr: optee@9e800000 {
			reg = <0x00 0x9e800000 0x00 0x01800000>; /* for OP-TEE */
			no-map;
		};
	};

	reg_3v3: regulator-3v3 {
		compatible = "regulator-fixed";
		regulator-name = "On-module +V3.3";
		regulator-min-microvolt = <3300000>;
		regulator-max-microvolt = <3300000>;
		regulator-always-on;
		regulator-boot-on;
	};

	reg_1v8: regulator-1v8 {
		compatible = "regulator-fixed";
		regulator-name = "On-module +V1.8";
		regulator-min-microvolt = <1800000>;
		regulator-max-microvolt = <1800000>;
		vin-supply = <&reg_3v3>;
		regulator-always-on;
		regulator-boot-on;
	};

	reg_3v3_phy: regulator-3v3-phy {
		compatible = "regulator-fixed";
		regulator-name = "On-module +V3.3_PHY";
		gpios = <&main_gpio0 45 GPIO_ACTIVE_HIGH>;
		enable-active-high;
		regulator-always-on;
	};
};

&cpsw3g {
	pinctrl-names = "default";
	pinctrl-0 = <&pinctrl_rgmii1>;
};

&cpsw3g_mdio {
	pinctrl-names = "default";
	pinctrl-0 = <&pinctrl_mdio1>;
	status = "okay";

	cpsw3g_phy0: ethernet-phy@4 {
		compatible = "ethernet-phy-id0283.bc30";
		reg = <4>;
		reset-gpios = <&main_gpio0 46 GPIO_ACTIVE_LOW>;
		reset-assert-us = <10000>;
		reset-deassert-us = <100000>;
	};
};

&cpsw_port1 {
	/*
	 * The required RGMII TX and RX 2ns delays are implemented directly
	 * in hardware via passive delay elements on the SOM PCB.
	 * No delay configuration is needed in software via PHY driver.
	 */
	phy-mode = "rgmii";
	phy-handle = <&cpsw3g_phy0>;
	status = "okay";
};

&main_i2c2 {
	pinctrl-names = "default";
	pinctrl-0 = <&pinctrl_i2c2>;
	clock-frequency = <400000>;
	status = "okay";
};

&main_i2c3 {
	pinctrl-names = "default";
	pinctrl-0 = <&pinctrl_i2c3>;
	clock-frequency = <400000>;
	status = "okay";
};

&main_pmx0 {
	pinctrl_mmc_pwrseq: main-emmc-pwrseq-pins {
		pinctrl-single,pins = <
			AM62PX_IOPAD(0x00c8, PIN_OUTPUT, 7) /* (AB23) VOUT0_DATA4.GPIO0_49 */
		>;
	};

	pinctrl_i2c2: main-i2c2-default-pins {
		pinctrl-single,pins = <
			AM62PX_IOPAD(0x00b0, PIN_INPUT_PULLUP, 1) /* (T22) GPMC0_CSn2.I2C2_SCL */
			AM62PX_IOPAD(0x00b4, PIN_INPUT_PULLUP, 1) /* (U25) GPMC0_CSn3.I2C2_SDA */
		>;
	};

	pinctrl_i2c3: main-i2c3-default-pins {
		pinctrl-single,pins = <
			AM62PX_IOPAD(0x01d0, PIN_INPUT_PULLUP, 2) /* (A23) UART0_CTSn.I2C3_SCL */
			AM62PX_IOPAD(0x01d4, PIN_INPUT_PULLUP, 2) /* (C22) UART0_RTSn.I2C3_SDA */
		>;
	};

	pinctrl_mdio1: main-mdio1-default-pins {
		pinctrl-single,pins = <
			AM62PX_IOPAD(0x0160, PIN_OUTPUT, 0) /* (F17) MDIO0_MDC */
			AM62PX_IOPAD(0x015c, PIN_INPUT, 0) /* (F16) MDIO0_MDIO */
		>;
	};

	pinctrl_mmc2: main-mmc2-default-pins {
		pinctrl-single,pins = <
			AM62PX_IOPAD(0x0120, PIN_INPUT_PULLUP, 0) /* (K24) MMC2_CMD */
			AM62PX_IOPAD(0x0118, PIN_INPUT_PULLDOWN, 0) /* (K21) MMC2_CLK */
			AM62PX_IOPAD(0x011c, PIN_INPUT_PULLUP, 0) /* () MMC2_CLKLB */
			AM62PX_IOPAD(0x0114, PIN_INPUT_PULLUP, 0) /* (K23) MMC2_DAT0 */
			AM62PX_IOPAD(0x0110, PIN_INPUT_PULLUP, 0) /* (K22) MMC2_DAT1 */
			AM62PX_IOPAD(0x010c, PIN_INPUT_PULLUP, 0) /* (L20) MMC2_DAT2 */
			AM62PX_IOPAD(0x0108, PIN_INPUT_PULLUP, 0) /* (L21) MMC2_DAT3 */
		>;
	};

	pinctrl_rgmii1: main-rgmii1-default-pins {
		pinctrl-single,pins = <
			AM62PX_IOPAD(0x014c, PIN_INPUT, 0) /* (B15) RGMII1_RD0 */
			AM62PX_IOPAD(0x0150, PIN_INPUT, 0) /* (B16) RGMII1_RD1 */
			AM62PX_IOPAD(0x0154, PIN_INPUT, 0) /* (A14) RGMII1_RD2 */
			AM62PX_IOPAD(0x0158, PIN_INPUT, 0) /* (B14) RGMII1_RD3 */
			AM62PX_IOPAD(0x0148, PIN_INPUT, 0) /* (A16) RGMII1_RXC */
			AM62PX_IOPAD(0x0144, PIN_INPUT, 0) /* (A15) RGMII1_RX_CTL */
			AM62PX_IOPAD(0x0134, PIN_INPUT, 0) /* (A18) RGMII1_TD0 */
			AM62PX_IOPAD(0x0138, PIN_INPUT, 0) /* (C17) RGMII1_TD1 */
			AM62PX_IOPAD(0x013c, PIN_INPUT, 0) /* (A17) RGMII1_TD2 */
			AM62PX_IOPAD(0x0140, PIN_INPUT, 0) /* (C16) RGMII1_TD3 */
			AM62PX_IOPAD(0x0130, PIN_INPUT, 0) /* (B17) RGMII1_TXC */
			AM62PX_IOPAD(0x012c, PIN_INPUT, 0) /* (B18) RGMII1_TX_CTL */
		>;
		bootph-all;
	};

	pinctrl_spi0: main-spi0-default-pins {
		pinctrl-single,pins = <
			AM62PX_IOPAD(0x01bc, PIN_OUTPUT, 0) /* (B21) SPI0_CLK */
			AM62PX_IOPAD(0x01b4, PIN_OUTPUT, 0) /* (D20) SPI0_CS0 */
			AM62PX_IOPAD(0x01c0, PIN_OUTPUT, 0) /* (B20) SPI0_D0 */
			AM62PX_IOPAD(0x01c4, PIN_INPUT, 0) /* (C21) SPI0_D1 */
		>;
	};

	pinctrl_uart5: main-uart5-default-pins {
		pinctrl-single,pins = <
			AM62PX_IOPAD(0x00ec, PIN_INPUT, 4) /* (AC21) VOUT0_DATA13.UART5_CTSn */
			AM62PX_IOPAD(0x00e8, PIN_OUTPUT, 4) /* (AD21) VOUT0_DATA12.UART5_RTSn */
			AM62PX_IOPAD(0x00d0, PIN_INPUT, 4) /* (AC23) VOUT0_DATA6.UART5_RXD */
			AM62PX_IOPAD(0x00d4, PIN_OUTPUT, 4) /* (AE23) VOUT0_DATA7.UART5_TXD */
		>;
	};

	pinctrl_bt: main-btgrp-pins {
		pinctrl-single,pins = <
			AM62PX_IOPAD(0x00f4, PIN_OUTPUT, 7) /* (Y20) VOUT0_DATA15.GPIO0_60 (BT_EN) */
		>;
	};

	pinctrl_restouch: main-restouch-pins {
		pinctrl-single,pins = <
			AM62PX_IOPAD(0x00c4, PIN_INPUT_PULLUP, 7) /* (Y23) VOUT0_DATA3.GPIO0_48 */
		>;
	};

	pinctrl_wifi: main-wifi-default-pins {
		pinctrl-single,pins = <
			AM62PX_IOPAD(0x00dc, PIN_OUTPUT, 7) /* (AC22) VOUT0_DATA9.GPIO0_54 - WIFI_PWR_EN - */
			AM62PX_IOPAD(0x00f0, PIN_OUTPUT, 7) /* (AA20) VOUT0_DATA14.GPIO0_59 - WIFI_EN - */
		>;
	};
};

&mcu_pmx0 {
	pinctrl_wkup_clkout0: wkup-clkout0-default-pins {
		pinctrl-single,pins = <
			AM62PX_MCU_IOPAD(0x0084, PIN_OUTPUT, 0) /* (F13) WKUP_CLKOUT0 */
		>;
	};
};

&main_spi0 {
	pinctrl-names = "default";
	pinctrl-0 = <&pinctrl_spi0>;
	ti,pindir-d0-out-d1-in;
	status = "okay";
};

&main_uart5 {
	pinctrl-names = "default";
	pinctrl-0 = <&pinctrl_uart5>, <&pinctrl_bt>;
	uart-has-rtscts;
	status = "okay";

	bluetooth {
		compatible = "nxp,88w8987-bt";
	};
};

&sdhci0 {
	/* On-module eMMC */
	ti,driver-strength-ohm = <50>;
	mmc-pwrseq = <&mmc_pwrseq>;
	bootph-all;
	status = "okay";
};

&sdhci2 {
	/* On-module WiFi */
	pinctrl-names = "default";
	pinctrl-0 = <&pinctrl_mmc2>, <&pinctrl_wifi>;
	bus-width = <4>;
	non-removable;
	keep-power-in-suspend;
	mmc-pwrseq = <&wifi_pwrseq>;
	ti,fails-without-test-cd;
	status = "okay";
};

&usbss0 {
	ti,vbus-divider;
};

&usbss1 {
	ti,vbus-divider;
};

&mailbox0_cluster0 {
	status = "okay";

	mbox_r5_0: mbox-r5-0 {
		ti,mbox-rx = <0 0 0>;
		ti,mbox-tx = <1 0 0>;
	};
};

&mailbox0_cluster1 {
	status = "okay";

	mbox_mcu_r5_0: mbox-mcu-r5-0 {
		ti,mbox-rx = <0 0 0>;
		ti,mbox-tx = <1 0 0>;
	};
};

&mcu_r5fss0 {
	status = "okay";
};

&mcu_r5fss0_core0 {
	mboxes = <&mailbox0_cluster1 &mbox_mcu_r5_0>;
	memory-region = <&mcu_r5fss0_core0_dma_memory_region>,
			<&mcu_r5fss0_core0_memory_region>;
};

&wkup_r5fss0 {
	status = "okay";
};

&wkup_r5fss0_core0 {
	mboxes = <&mailbox0_cluster0 &mbox_r5_0>;
	memory-region = <&wkup_r5fss0_core0_dma_memory_region>,
			<&wkup_r5fss0_core0_memory_region>;
};

/* mcu_gpio0 and mcu_gpio_intr are reserved for mcu firmware usage */
&mcu_gpio0 {
	status = "reserved";
};

&mcu_gpio_intr {
	status = "reserved";
};

&wkup_rtc0 {
	status = "disabled";
};

&wkup_rti0 {
	/* WKUP RTI0 is used by DM firmware */
	status = "reserved";
};

&wkup_uart0 {
	/* WKUP UART0 is used by DM firmware */
	status = "reserved";
};

&main_uart1 {
	/* Main UART1 is used by TIFS firmware */
	status = "reserved";
};