xref: /linux/arch/arm/boot/dts/ti/omap/am4372.dtsi (revision 0e2b2a76278153d1ac312b0691cb65dabb9aef3e)
1// SPDX-License-Identifier: GPL-2.0-only
2/*
3 * Device Tree Source for AM4372 SoC
4 *
5 * Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com/
6 */
7
8#include <dt-bindings/bus/ti-sysc.h>
9#include <dt-bindings/gpio/gpio.h>
10#include <dt-bindings/interrupt-controller/arm-gic.h>
11#include <dt-bindings/clock/am4.h>
12
13/ {
14	compatible = "ti,am4372", "ti,am43";
15	interrupt-parent = <&wakeupgen>;
16	#address-cells = <1>;
17	#size-cells = <1>;
18	chosen { };
19
20	memory@0 {
21		device_type = "memory";
22		reg = <0 0>;
23	};
24
25	aliases {
26		i2c0 = &i2c0;
27		i2c1 = &i2c1;
28		i2c2 = &i2c2;
29		serial0 = &uart0;
30		serial1 = &uart1;
31		serial2 = &uart2;
32		serial3 = &uart3;
33		serial4 = &uart4;
34		serial5 = &uart5;
35		ethernet0 = &cpsw_port1;
36		ethernet1 = &cpsw_port2;
37		spi0 = &qspi;
38	};
39
40	cpus {
41		#address-cells = <1>;
42		#size-cells = <0>;
43		cpu: cpu@0 {
44			compatible = "arm,cortex-a9";
45			enable-method = "ti,am4372";
46			device_type = "cpu";
47			reg = <0>;
48
49			clocks = <&dpll_mpu_ck>;
50			clock-names = "cpu";
51
52			operating-points-v2 = <&cpu0_opp_table>;
53
54			clock-latency = <300000>; /* From omap-cpufreq driver */
55			cpu-idle-states = <&mpu_gate>;
56		};
57
58		idle-states {
59			mpu_gate: mpu_gate {
60				compatible = "arm,idle-state";
61				entry-latency-us = <40>;
62				exit-latency-us = <100>;
63				min-residency-us = <300>;
64				local-timer-stop;
65			};
66		};
67	};
68
69	cpu0_opp_table: opp-table {
70		compatible = "operating-points-v2-ti-cpu";
71		syscon = <&scm_conf>;
72
73		opp50-300000000 {
74			opp-hz = /bits/ 64 <300000000>;
75			opp-microvolt = <950000 931000 969000>;
76			opp-supported-hw = <0xFF 0x01>;
77			opp-suspend;
78		};
79
80		opp100-600000000 {
81			opp-hz = /bits/ 64 <600000000>;
82			opp-microvolt = <1100000 1078000 1122000>;
83			opp-supported-hw = <0xFF 0x04>;
84		};
85
86		opp120-720000000 {
87			opp-hz = /bits/ 64 <720000000>;
88			opp-microvolt = <1200000 1176000 1224000>;
89			opp-supported-hw = <0xFF 0x08>;
90		};
91
92		oppturbo-800000000 {
93			opp-hz = /bits/ 64 <800000000>;
94			opp-microvolt = <1260000 1234800 1285200>;
95			opp-supported-hw = <0xFF 0x10>;
96		};
97
98		oppnitro-1000000000 {
99			opp-hz = /bits/ 64 <1000000000>;
100			opp-microvolt = <1325000 1298500 1351500>;
101			opp-supported-hw = <0xFF 0x20>;
102		};
103	};
104
105	soc {
106		compatible = "ti,omap-infra";
107	};
108
109	gic: interrupt-controller@48241000 {
110		compatible = "arm,cortex-a9-gic";
111		interrupt-controller;
112		#interrupt-cells = <3>;
113		reg = <0x48241000 0x1000>,
114		      <0x48240100 0x0100>;
115		interrupt-parent = <&gic>;
116	};
117
118	wakeupgen: interrupt-controller@48281000 {
119		compatible = "ti,omap4-wugen-mpu";
120		interrupt-controller;
121		#interrupt-cells = <3>;
122		reg = <0x48281000 0x1000>;
123		interrupt-parent = <&gic>;
124	};
125
126	scu: scu@48240000 {
127		compatible = "arm,cortex-a9-scu";
128		reg = <0x48240000 0x100>;
129	};
130
131	global_timer: timer@48240200 {
132		compatible = "arm,cortex-a9-global-timer";
133		reg = <0x48240200 0x100>;
134		interrupts = <GIC_PPI 11 IRQ_TYPE_EDGE_RISING>;
135		interrupt-parent = <&gic>;
136		clocks = <&mpu_periphclk>;
137	};
138
139	local_timer: timer@48240600 {
140		compatible = "arm,cortex-a9-twd-timer";
141		reg = <0x48240600 0x100>;
142		interrupts = <GIC_PPI 13 IRQ_TYPE_EDGE_RISING>;
143		interrupt-parent = <&gic>;
144		clocks = <&mpu_periphclk>;
145	};
146
147	cache-controller@48242000 {
148		compatible = "arm,pl310-cache";
149		reg = <0x48242000 0x1000>;
150		cache-unified;
151		cache-level = <2>;
152	};
153
154	ocp@44000000 {
155		compatible = "simple-pm-bus";
156		power-domains = <&prm_per>;
157		clocks = <&l3_clkctrl AM4_L3_L3_MAIN_CLKCTRL 0>;
158		clock-names = "fck";
159		#address-cells = <1>;
160		#size-cells = <1>;
161		ranges;
162		ti,no-idle;
163
164		l3-noc@44000000 {
165			compatible = "ti,am4372-l3-noc";
166			reg = <0x44000000 0x400000>,
167			      <0x44800000 0x400000>;
168			interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
169				     <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
170		};
171
172		l4_wkup: interconnect@44c00000 {
173		};
174		l4_per: interconnect@48000000 {
175		};
176		l4_fast: interconnect@4a000000 {
177		};
178
179		target-module@4c000000 {
180			compatible = "ti,sysc-omap4-simple", "ti,sysc";
181			reg = <0x4c000000 0x4>;
182			reg-names = "rev";
183			clocks = <&emif_clkctrl AM4_EMIF_EMIF_CLKCTRL 0>;
184			clock-names = "fck";
185			ti,no-idle;
186			#address-cells = <1>;
187			#size-cells = <1>;
188			ranges = <0x0 0x4c000000 0x1000000>;
189
190			emif: emif@0 {
191				compatible = "ti,emif-am4372";
192				reg = <0 0x1000000>;
193				interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
194				sram = <&pm_sram_code
195					&pm_sram_data>;
196			};
197		};
198
199		target-module@49000000 {
200			compatible = "ti,sysc-omap4", "ti,sysc";
201			reg = <0x49000000 0x4>;
202			reg-names = "rev";
203			clocks = <&l3_clkctrl AM4_L3_TPCC_CLKCTRL 0>;
204			clock-names = "fck";
205			#address-cells = <1>;
206			#size-cells = <1>;
207			ranges = <0x0 0x49000000 0x10000>;
208
209			edma: dma@0 {
210				compatible = "ti,edma3-tpcc";
211				reg = <0 0x10000>;
212				reg-names = "edma3_cc";
213				interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
214					     <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
215					     <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
216				interrupt-names = "edma3_ccint", "edma3_mperr",
217						  "edma3_ccerrint";
218				dma-requests = <64>;
219				#dma-cells = <2>;
220
221				ti,tptcs = <&edma_tptc0 7>, <&edma_tptc1 5>,
222					   <&edma_tptc2 0>;
223
224				ti,edma-memcpy-channels = <58 59>;
225			};
226		};
227
228		target-module@49800000 {
229			compatible = "ti,sysc-omap4", "ti,sysc";
230			reg = <0x49800000 0x4>,
231			      <0x49800010 0x4>;
232			reg-names = "rev", "sysc";
233			ti,sysc-mask = <SYSC_OMAP4_SOFTRESET>;
234			ti,sysc-midle = <SYSC_IDLE_FORCE>;
235			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
236					<SYSC_IDLE_SMART>;
237			clocks = <&l3_clkctrl AM4_L3_TPTC0_CLKCTRL 0>;
238			clock-names = "fck";
239			#address-cells = <1>;
240			#size-cells = <1>;
241			ranges = <0x0 0x49800000 0x100000>;
242
243			edma_tptc0: dma@0 {
244				compatible = "ti,edma3-tptc";
245				reg = <0 0x100000>;
246				interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>;
247				interrupt-names = "edma3_tcerrint";
248			};
249		};
250
251		target-module@49900000 {
252			compatible = "ti,sysc-omap4", "ti,sysc";
253			reg = <0x49900000 0x4>,
254			      <0x49900010 0x4>;
255			reg-names = "rev", "sysc";
256			ti,sysc-mask = <SYSC_OMAP4_SOFTRESET>;
257			ti,sysc-midle = <SYSC_IDLE_FORCE>;
258			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
259					<SYSC_IDLE_SMART>;
260			clocks = <&l3_clkctrl AM4_L3_TPTC1_CLKCTRL 0>;
261			clock-names = "fck";
262			#address-cells = <1>;
263			#size-cells = <1>;
264			ranges = <0x0 0x49900000 0x100000>;
265
266			edma_tptc1: dma@0 {
267				compatible = "ti,edma3-tptc";
268				reg = <0 0x100000>;
269				interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
270				interrupt-names = "edma3_tcerrint";
271			};
272		};
273
274		target-module@49a00000 {
275			compatible = "ti,sysc-omap4", "ti,sysc";
276			reg = <0x49a00000 0x4>,
277			      <0x49a00010 0x4>;
278			reg-names = "rev", "sysc";
279			ti,sysc-mask = <SYSC_OMAP4_SOFTRESET>;
280			ti,sysc-midle = <SYSC_IDLE_FORCE>;
281			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
282					<SYSC_IDLE_SMART>;
283			clocks = <&l3_clkctrl AM4_L3_TPTC2_CLKCTRL 0>;
284			clock-names = "fck";
285			#address-cells = <1>;
286			#size-cells = <1>;
287			ranges = <0x0 0x49a00000 0x100000>;
288
289			edma_tptc2: dma@0 {
290				compatible = "ti,edma3-tptc";
291				reg = <0 0x100000>;
292				interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>;
293				interrupt-names = "edma3_tcerrint";
294			};
295		};
296
297		target-module@47810000 {
298			compatible = "ti,sysc-omap2", "ti,sysc";
299			reg = <0x478102fc 0x4>,
300			      <0x47810110 0x4>,
301			      <0x47810114 0x4>;
302			reg-names = "rev", "sysc", "syss";
303			ti,sysc-mask = <(SYSC_OMAP2_CLOCKACTIVITY |
304					 SYSC_OMAP2_ENAWAKEUP |
305					 SYSC_OMAP2_SOFTRESET |
306					 SYSC_OMAP2_AUTOIDLE)>;
307			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
308					<SYSC_IDLE_NO>,
309					<SYSC_IDLE_SMART>;
310			ti,syss-mask = <1>;
311			clocks = <&l3s_clkctrl AM4_L3S_MMC3_CLKCTRL 0>;
312			clock-names = "fck";
313			#address-cells = <1>;
314			#size-cells = <1>;
315			ranges = <0x0 0x47810000 0x1000>;
316
317			mmc3: mmc@0 {
318				compatible = "ti,am437-sdhci";
319				ti,needs-special-reset;
320				interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
321				reg = <0x0 0x1000>;
322				status = "disabled";
323			};
324		};
325
326		sham_target: target-module@53100000 {
327			compatible = "ti,sysc-omap3-sham", "ti,sysc";
328			reg = <0x53100100 0x4>,
329			      <0x53100110 0x4>,
330			      <0x53100114 0x4>;
331			reg-names = "rev", "sysc", "syss";
332			ti,sysc-mask = <(SYSC_OMAP2_SOFTRESET |
333					 SYSC_OMAP2_AUTOIDLE)>;
334			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
335					<SYSC_IDLE_NO>,
336					<SYSC_IDLE_SMART>;
337			ti,syss-mask = <1>;
338			/* Domains (P, C): per_pwrdm, l3_clkdm */
339			clocks = <&l3_clkctrl AM4_L3_SHAM_CLKCTRL 0>;
340			clock-names = "fck";
341			#address-cells = <1>;
342			#size-cells = <1>;
343			ranges = <0x0 0x53100000 0x1000>;
344
345			sham: sham@0 {
346				compatible = "ti,omap5-sham";
347				reg = <0 0x300>;
348				dmas = <&edma 36 0>;
349				dma-names = "rx";
350				interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
351			};
352		};
353
354		aes_target: target-module@53501000 {
355			compatible = "ti,sysc-omap2", "ti,sysc";
356			reg = <0x53501080 0x4>,
357			      <0x53501084 0x4>,
358			      <0x53501088 0x4>;
359			reg-names = "rev", "sysc", "syss";
360			ti,sysc-mask = <(SYSC_OMAP2_SOFTRESET |
361					 SYSC_OMAP2_AUTOIDLE)>;
362			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
363					<SYSC_IDLE_NO>,
364					<SYSC_IDLE_SMART>,
365					<SYSC_IDLE_SMART_WKUP>;
366			ti,syss-mask = <1>;
367			/* Domains (P, C): per_pwrdm, l3_clkdm */
368			clocks = <&l3_clkctrl AM4_L3_AES_CLKCTRL 0>;
369			clock-names = "fck";
370			#address-cells = <1>;
371			#size-cells = <1>;
372			ranges = <0x0 0x53501000 0x1000>;
373
374			aes: aes@0 {
375				compatible = "ti,omap4-aes";
376				reg = <0 0xa0>;
377				interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
378				dmas = <&edma 6 0>,
379				      <&edma 5 0>;
380				dma-names = "tx", "rx";
381			};
382		};
383
384		des_target: target-module@53701000 {
385			compatible = "ti,sysc-omap2", "ti,sysc";
386			reg = <0x53701030 0x4>,
387			      <0x53701034 0x4>,
388			      <0x53701038 0x4>;
389			reg-names = "rev", "sysc", "syss";
390			ti,sysc-mask = <(SYSC_OMAP2_SOFTRESET |
391					 SYSC_OMAP2_AUTOIDLE)>;
392			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
393					<SYSC_IDLE_NO>,
394					<SYSC_IDLE_SMART>,
395					<SYSC_IDLE_SMART_WKUP>;
396			ti,syss-mask = <1>;
397			/* Domains (P, C): per_pwrdm, l3_clkdm */
398			clocks = <&l3_clkctrl AM4_L3_DES_CLKCTRL 0>;
399			clock-names = "fck";
400			#address-cells = <1>;
401			#size-cells = <1>;
402			ranges = <0 0x53701000 0x1000>;
403
404			des: des@0 {
405				compatible = "ti,omap4-des";
406				reg = <0 0xa0>;
407				interrupts = <GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>;
408				dmas = <&edma 34 0>,
409				       <&edma 33 0>;
410				dma-names = "tx", "rx";
411			};
412		};
413
414		pruss_tm: target-module@54400000 {
415			compatible = "ti,sysc-pruss", "ti,sysc";
416			reg = <0x54426000 0x4>,
417			      <0x54426004 0x4>;
418			reg-names = "rev", "sysc";
419			ti,sysc-mask = <(SYSC_PRUSS_STANDBY_INIT |
420					 SYSC_PRUSS_SUB_MWAIT)>;
421			ti,sysc-midle = <SYSC_IDLE_FORCE>,
422					<SYSC_IDLE_NO>,
423					<SYSC_IDLE_SMART>;
424			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
425					<SYSC_IDLE_NO>,
426					<SYSC_IDLE_SMART>;
427			clocks = <&pruss_ocp_clkctrl AM4_PRUSS_OCP_PRUSS_CLKCTRL 0>;
428			clock-names = "fck";
429			resets = <&prm_per 1>;
430			reset-names = "rstctrl";
431			#address-cells = <1>;
432			#size-cells = <1>;
433			ranges = <0x0 0x54400000 0x80000>;
434
435			pruss1: pruss@0 {
436				compatible = "ti,am4376-pruss1";
437				reg = <0x0 0x40000>;
438				#address-cells = <1>;
439				#size-cells = <1>;
440				ranges;
441
442				pruss1_mem: memories@0 {
443					reg = <0x0 0x2000>,
444					      <0x2000 0x2000>,
445					      <0x10000 0x8000>;
446					reg-names = "dram0", "dram1",
447						    "shrdram2";
448				};
449
450				pruss1_cfg: cfg@26000 {
451					compatible = "ti,pruss-cfg", "syscon";
452					reg = <0x26000 0x2000>;
453					#address-cells = <1>;
454					#size-cells = <1>;
455					ranges = <0x0 0x26000 0x2000>;
456
457					clocks {
458						#address-cells = <1>;
459						#size-cells = <0>;
460
461						pruss1_iepclk_mux: iepclk-mux@30 {
462							reg = <0x30>;
463							#clock-cells = <0>;
464							clocks = <&sysclk_div>,     /* icss_iep_gclk */
465								 <&pruss_ocp_gclk>; /* icss_ocp_gclk */
466						};
467					};
468				};
469
470				pruss1_mii_rt: mii-rt@32000 {
471					compatible = "ti,pruss-mii", "syscon";
472					reg = <0x32000 0x58>;
473				};
474
475				pruss1_intc: interrupt-controller@20000 {
476					compatible = "ti,pruss-intc";
477					reg = <0x20000 0x2000>;
478					interrupt-controller;
479					#interrupt-cells = <3>;
480					interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>,
481						     <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>,
482						     <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>,
483						     <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>,
484						     <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>,
485						     <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>,
486						     <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>;
487					interrupt-names = "host_intr0", "host_intr1",
488							  "host_intr2", "host_intr3",
489							  "host_intr4",
490							  "host_intr6", "host_intr7";
491					ti,irqs-reserved = /bits/ 8 <0x20>; /* BIT(5) */
492				};
493
494				pru1_0: pru@34000 {
495					compatible = "ti,am4376-pru";
496					reg = <0x34000 0x3000>,
497					      <0x22000 0x400>,
498					      <0x22400 0x100>;
499					reg-names = "iram", "control", "debug";
500					firmware-name = "am437x-pru1_0-fw";
501				};
502
503				pru1_1: pru@38000 {
504					compatible = "ti,am4376-pru";
505					reg = <0x38000 0x3000>,
506					      <0x24000 0x400>,
507					      <0x24400 0x100>;
508					reg-names = "iram", "control", "debug";
509					firmware-name = "am437x-pru1_1-fw";
510				};
511
512				pruss1_mdio: mdio@32400 {
513					compatible = "ti,davinci_mdio";
514					reg = <0x32400 0x90>;
515					clocks = <&dpll_core_m4_ck>;
516					clock-names = "fck";
517					bus_freq = <1000000>;
518					#address-cells = <1>;
519					#size-cells = <0>;
520				};
521			};
522
523			pruss0: pruss@40000 {
524				compatible = "ti,am4376-pruss0";
525				reg = <0x40000 0x40000>;
526				#address-cells = <1>;
527				#size-cells = <1>;
528				ranges;
529
530				pruss0_mem: memories@40000 {
531					reg = <0x40000 0x1000>,
532					      <0x42000 0x1000>;
533					reg-names = "dram0", "dram1";
534				};
535
536				pruss0_cfg: cfg@66000 {
537					compatible = "ti,pruss-cfg", "syscon";
538					reg = <0x66000 0x2000>;
539					#address-cells = <1>;
540					#size-cells = <1>;
541					ranges = <0x0 0x66000 0x2000>;
542
543					clocks {
544						#address-cells = <1>;
545						#size-cells = <0>;
546
547						pruss0_iepclk_mux: iepclk-mux@30 {
548							reg = <0x30>;
549							#clock-cells = <0>;
550							clocks = <&sysclk_div>,     /* icss_iep_gclk */
551								 <&pruss_ocp_gclk>; /* icss_ocp_gclk */
552						};
553					};
554				};
555
556				pruss0_mii_rt: mii-rt@72000 {
557					compatible = "ti,pruss-mii", "syscon";
558					reg = <0x72000 0x58>;
559					status = "disabled";
560				};
561
562				pruss0_intc: interrupt-controller@60000 {
563					compatible = "ti,pruss-intc";
564					reg = <0x60000 0x2000>;
565					interrupt-controller;
566					#interrupt-cells = <3>;
567					interrupts = <GIC_SPI 159 IRQ_TYPE_LEVEL_HIGH>,
568						     <GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>,
569						     <GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH>,
570						     <GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>,
571						     <GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>,
572						     <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>,
573						     <GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>;
574					interrupt-names = "host_intr0", "host_intr1",
575							  "host_intr2", "host_intr3",
576							  "host_intr4",
577							  "host_intr6", "host_intr7";
578					ti,irqs-reserved = /bits/ 8 <0x20>; /* BIT(5) */
579				};
580
581				pru0_0: pru@74000 {
582					compatible = "ti,am4376-pru";
583					reg = <0x74000 0x1000>,
584					      <0x62000 0x400>,
585					      <0x62400 0x100>;
586					reg-names = "iram", "control", "debug";
587					firmware-name = "am437x-pru0_0-fw";
588				};
589
590				pru0_1: pru@78000 {
591					compatible = "ti,am4376-pru";
592					reg = <0x78000 0x1000>,
593					      <0x64000 0x400>,
594					      <0x64400 0x100>;
595					reg-names = "iram", "control", "debug";
596					firmware-name = "am437x-pru0_1-fw";
597				};
598			};
599		};
600
601		target-module@50000000 {
602			compatible = "ti,sysc-omap2", "ti,sysc";
603			reg = <0x50000000 4>,
604			      <0x50000010 4>,
605			      <0x50000014 4>;
606			reg-names = "rev", "sysc", "syss";
607			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
608					<SYSC_IDLE_NO>,
609					<SYSC_IDLE_SMART>;
610			ti,syss-mask = <1>;
611			clocks = <&l3s_clkctrl AM4_L3S_GPMC_CLKCTRL 0>;
612			clock-names = "fck";
613			#address-cells = <1>;
614			#size-cells = <1>;
615			ranges = <0x50000000 0x50000000 0x00001000>, /* regs */
616				 <0x00000000 0x00000000 0x40000000>; /* data */
617
618			gpmc: gpmc@50000000 {
619				compatible = "ti,am3352-gpmc";
620				dmas = <&edma 52 0>;
621				dma-names = "rxtx";
622				clocks = <&l3s_gclk>;
623				clock-names = "fck";
624				reg = <0x50000000 0x2000>;
625				interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
626				gpmc,num-cs = <7>;
627				gpmc,num-waitpins = <2>;
628				#address-cells = <2>;
629				#size-cells = <1>;
630				interrupt-controller;
631				#interrupt-cells = <2>;
632				gpio-controller;
633				#gpio-cells = <2>;
634				status = "disabled";
635			};
636		};
637
638		target-module@47900000 {
639			compatible = "ti,sysc-omap4", "ti,sysc";
640			reg = <0x47900000 0x4>,
641			      <0x47900010 0x4>;
642			reg-names = "rev", "sysc";
643			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
644					<SYSC_IDLE_NO>,
645					<SYSC_IDLE_SMART>,
646					<SYSC_IDLE_SMART_WKUP>;
647			clocks = <&l3s_clkctrl AM4_L3S_QSPI_CLKCTRL 0>;
648			clock-names = "fck";
649			#address-cells = <1>;
650			#size-cells = <1>;
651			ranges = <0x0 0x47900000 0x1000>,
652				 <0x30000000 0x30000000 0x4000000>;
653
654			qspi: spi@0 {
655				compatible = "ti,am4372-qspi";
656				reg = <0 0x100>,
657				      <0x30000000 0x4000000>;
658				reg-names = "qspi_base", "qspi_mmap";
659				clocks = <&dpll_per_m2_div4_ck>;
660				clock-names = "fck";
661				#address-cells = <1>;
662				#size-cells = <0>;
663				interrupts = <0 138 0x4>;
664				num-cs = <4>;
665			};
666		};
667
668		target-module@40300000 {
669			compatible = "ti,sysc-omap4-simple", "ti,sysc";
670			clocks = <&l3_clkctrl AM4_L3_OCMCRAM_CLKCTRL 0>;
671			clock-names = "fck";
672			ti,no-idle;
673			#address-cells = <1>;
674			#size-cells = <1>;
675			ranges = <0 0x40300000 0x40000>;
676
677			ocmcram: sram@0 {
678				compatible = "mmio-sram";
679				reg = <0 0x40000>; /* 256k */
680				ranges = <0 0 0x40000>;
681				#address-cells = <1>;
682				#size-cells = <1>;
683
684				pm_sram_code: pm-code-sram@0 {
685					compatible = "ti,sram";
686					reg = <0x0 0x1000>;
687					protect-exec;
688				};
689
690				pm_sram_data: pm-data-sram@1000 {
691					compatible = "ti,sram";
692					reg = <0x1000 0x1000>;
693					pool;
694				};
695			};
696		};
697
698		target-module@56000000 {
699			compatible = "ti,sysc-omap4", "ti,sysc";
700			reg = <0x5600fe00 0x4>,
701			      <0x5600fe10 0x4>;
702			reg-names = "rev", "sysc";
703			ti,sysc-midle = <SYSC_IDLE_FORCE>,
704					<SYSC_IDLE_NO>,
705					<SYSC_IDLE_SMART>;
706			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
707					<SYSC_IDLE_NO>,
708					<SYSC_IDLE_SMART>;
709			clocks = <&gfx_l3_clkctrl AM4_GFX_L3_GFX_CLKCTRL 0>;
710			clock-names = "fck";
711			power-domains = <&prm_gfx>;
712			resets = <&prm_gfx 0>;
713			reset-names = "rstctrl";
714			#address-cells = <1>;
715			#size-cells = <1>;
716			ranges = <0 0x56000000 0x1000000>;
717		};
718	};
719};
720
721#include "am437x-l4.dtsi"
722#include "am43xx-clocks.dtsi"
723
724&prcm {
725	prm_mpu: prm@300 {
726		compatible = "ti,am4-prm-inst", "ti,omap-prm-inst";
727		reg = <0x300 0x100>;
728		#power-domain-cells = <0>;
729	};
730
731	prm_gfx: prm@400 {
732		compatible = "ti,am4-prm-inst", "ti,omap-prm-inst";
733		reg = <0x400 0x100>;
734		#power-domain-cells = <0>;
735		#reset-cells = <1>;
736	};
737
738	prm_rtc: prm@500 {
739		compatible = "ti,am4-prm-inst", "ti,omap-prm-inst";
740		reg = <0x500 0x100>;
741		#power-domain-cells = <0>;
742	};
743
744	prm_tamper: prm@600 {
745		compatible = "ti,am4-prm-inst", "ti,omap-prm-inst";
746		reg = <0x600 0x100>;
747		#power-domain-cells = <0>;
748	};
749
750	prm_cefuse: prm@700 {
751		compatible = "ti,am4-prm-inst", "ti,omap-prm-inst";
752		reg = <0x700 0x100>;
753		#power-domain-cells = <0>;
754	};
755
756	prm_per: prm@800 {
757		compatible = "ti,am4-prm-inst", "ti,omap-prm-inst";
758		reg = <0x800 0x100>;
759		#reset-cells = <1>;
760		#power-domain-cells = <0>;
761	};
762
763	prm_wkup: prm@2000 {
764		compatible = "ti,am4-prm-inst", "ti,omap-prm-inst";
765		reg = <0x2000 0x100>;
766		#reset-cells = <1>;
767		#power-domain-cells = <0>;
768	};
769
770	prm_device: prm@4000 {
771		compatible = "ti,am4-prm-inst", "ti,omap-prm-inst";
772		reg = <0x4000 0x100>;
773		#reset-cells = <1>;
774	};
775};
776
777/* Preferred always-on timer for clocksource */
778&timer1_target {
779	ti,no-reset-on-init;
780	ti,no-idle;
781	clocks = <&l4_wkup_clkctrl AM4_L4_WKUP_TIMER1_CLKCTRL 0>,
782		 <&l4_wkup_clkctrl AM4_L4_WKUP_L4_WKUP_CLKCTRL 0>;
783	clock-names = "fck", "ick";
784	timer@0 {
785		assigned-clocks = <&timer1_fck>;
786		assigned-clock-parents = <&sys_clkin_ck>;
787	};
788};
789
790/* Preferred timer for clockevent */
791&timer2_target {
792	ti,no-reset-on-init;
793	ti,no-idle;
794	clocks = <&l4ls_clkctrl AM4_L4LS_TIMER2_CLKCTRL 0>,
795		 <&l4ls_clkctrl AM4_L4LS_L4_LS_CLKCTRL 0>;
796	clock-names = "fck", "ick";
797	timer@0 {
798		assigned-clocks = <&timer2_fck>;
799		assigned-clock-parents = <&sys_clkin_ck>;
800	};
801};
802