| /linux/Documentation/networking/device_drivers/ethernet/intel/ |
| H A D | e1000.rst | 441 Enabling Wake on LAN (WoL)
|
| /linux/kernel/module/ |
| H A D | stats.c | 23 * Enabling CONFIG_MODULE_STATS enables module debugging statistics which
|
| /linux/Documentation/driver-api/surface_aggregator/ |
| H A D | ssh.rst | 281 the EC when setting up and enabling an event source (via the
|
| /linux/arch/arm/boot/dts/ti/omap/ |
| H A D | dra7-evm.dts | 442 * support NAND on dra7-evm. Keep it disabled. Enabling it
|
| /linux/sound/pcmcia/vx/ |
| H A D | vxp_ops.c | 208 /* Reset the Xilinx's signal enabling IO access */ in vxp_load_xilinx_binary()
|
| /linux/drivers/power/supply/ |
| H A D | rn5t618_power.c | 756 dev_info(&pdev->dev, "Fuel gauge not enabled, enabling now\n"); in rn5t618_power_probe()
|
| /linux/drivers/fsi/ |
| H A D | fsi-master-aspeed.c | 597 * Will need to be reworked when enabling DMA or anything that uses in fsi_master_aspeed_probe()
|
| /linux/drivers/net/ethernet/netronome/nfp/bpf/ |
| H A D | offload.c | 562 "FW command error while enabling BPF"); in nfp_net_bpf_start()
|
| /linux/drivers/gpu/drm/kmb/ |
| H A D | kmb_drv.c | 217 /* When disabling/enabling LCD layers, the change takes effect in handle_lcd_irq()
|
| /linux/drivers/acpi/acpica/ |
| H A D | exutils.c | 14 * by enabling a single header file to embody all knowledge of the names
|
| /linux/drivers/pmdomain/bcm/ |
| H A D | bcm2835-power.c | 61 /* The power gates must be enabled with this bit before enabling the LDO in the
|
| /linux/arch/powerpc/platforms/52xx/ |
| H A D | mpc52xx_pic.c | 62 * For actually manipulating IRQs (masking, enabling, clearing, etc) this
|
| /linux/drivers/iio/common/ssp_sensors/ |
| H A D | ssp_dev.c | 237 dev_err(&data->spi->dev, "Enabling sensor failed\n"); in ssp_enable_sensor()
|
| /linux/arch/mips/kernel/ |
| H A D | smp.c | 407 * irq will be enabled in ->smp_finish(), enabling it too early in start_secondary()
|
| /linux/arch/powerpc/perf/ |
| H A D | vpa-dtl.c | 578 pr_debug("not a shared virtualized system, not enabling\n"); in vpa_dtl_init()
|
| /linux/drivers/pinctrl/aspeed/ |
| H A D | pinctrl-aspeed.c | 80 pr_debug("Enabling signal %s for %s\n", expr->signal, in aspeed_sig_expr_enable()
|
| /linux/Documentation/userspace-api/ |
| H A D | iommufd.rst | 60 the user space (e.g. in a guest VM enabling the IOMMU nested translation
|
| /linux/sound/soc/sof/ |
| H A D | ipc3-dtrace.c | 171 dev_err(sdev->dev, "enabling device failed: %d\n", ret); in ipc3_trace_update_filter()
|
| /linux/drivers/base/ |
| H A D | cpu.c | 79 * When hot adding memory to memoryless node and enabling a cpu in cpu_subsys_online()
|
| /linux/drivers/net/ipa/ |
| H A D | ipa_endpoint.c | 564 * generate a SUSPEND IPA interrupt. If enabling suspend, have in ipa_endpoint_program_suspend()
1140 /* When enabling, the register must be written twice for IPA v4.5+ */ in ipa_endpoint_init_hol_block_en()
1733 /* Finally, reset and reconfigure the channel again (re-enabling in ipa_endpoint_reset_rx_aggr()
|
| /linux/sound/soc/codecs/ |
| H A D | wm8903.c | 395 dev_dbg(component->dev, "Enabling Class W\n"); in wm8903_class_w_put()
1171 dev_dbg(component->dev, "Enabling Class W\n"); in wm8903_set_bias_level()
1606 dev_dbg(component->dev, "Enabling microphone detection: %x %x\n", in wm8903_mic_detect()
|
| /linux/drivers/gpu/drm/i915/ |
| H A D | i915_perf.c | 1537 * We are enabling perf query here. If we don't find the context in oa_get_render_ctx_id()
1544 "Enabling perf query failed for %s\n", in oa_get_render_ctx_id()
1733 * when re-enabling a stream or in error/reset paths. in gen7_init_oa_buffer()
1786 * when re-enabling a stream or in error/reset paths. in gen8_init_oa_buffer()
1839 * when re-enabling a stream or in error/reset paths. in gen12_init_oa_buffer()
3588 * The intention is that disabling an re-enabling a stream will ideally be
3591 * must be retained between disabling and re-enabling a stream.
|
| /linux/drivers/tty/serial/ |
| H A D | imx.c | 1538 * configure tx polarity before enabling tx in imx_uart_startup()
1963 * Be careful about the order of enabling bits here. First enable the in imx_uart_poll_init()
2184 * actions (such as re-enabling the interrupts). in imx_uart_console_write_thread()
2524 "low-active RTS not possible when receiver is off, enabling receiver\n"); in imx_uart_probe()
|
| /linux/drivers/net/wireless/ath/ |
| H A D | regd.c | 371 * channel first before enabling active scan. The passive scan
|
| /linux/sound/soc/intel/atom/sst/ |
| H A D | sst.c | 387 * enabling the pm in sst_configure_runtime_pm()
|