| /linux/drivers/tty/serial/8250/ |
| H A D | 8250_em.c | 44 case UART_MCR: /* MCR @ 0x14 (+1) */ in serial8250_em_serial_out_helper()
68 case UART_MCR: /* MCR @ 0x14 (+1) */ in serial8250_em_serial_in()
92 mcr = serial8250_em_serial_in(p, UART_MCR); in serial8250_em_reg_update()
110 case UART_MCR: in serial8250_em_reg_update()
117 serial8250_em_serial_out_helper(p, UART_MCR, mcr); in serial8250_em_reg_update()
136 case UART_MCR: in serial8250_em_serial_out()
|
| H A D | 8250_rt288x.c | 23 [UART_MCR] = 6,
33 [UART_MCR] = 6,
|
| H A D | 8250_ingenic.c | 116 early_out(port, UART_MCR, UART_MCR_RTS | UART_MCR_DTR); in ingenic_earlycon_setup_tail()
189 case UART_MCR: in ingenic_uart_serial_out()
221 case UART_MCR: in ingenic_uart_serial_in()
|
| H A D | 8250_uniphier.c | 79 case UART_MCR: in uniphier_serial_in()
113 case UART_MCR: in uniphier_serial_out()
|
| H A D | 8250.h | 287 serial_out(up, UART_MCR, value); in serial8250_out_MCR()
297 mctrl = serial_in(up, UART_MCR); in serial8250_in_MCR()
|
| H A D | 8250_early.c | 141 serial8250_early_out(port, UART_MCR, UART_MCR_DTR | UART_MCR_RTS); in init_port()
|
| H A D | 8250_loongson.c | 59 case UART_MCR: in serial_fixup()
|
| H A D | 8250_exar.c | 1219 writeb(UART_MCR_OUT1, p + UART_MCR); in sealevel_rs485_config()
|
| /linux/drivers/accessibility/speakup/ |
| H A D | serialio.c | 96 outb(UART_MCR_DTR | UART_MCR_RTS, ser->port + UART_MCR); in spk_serial_init()
142 speakup_info.port_tts + UART_MCR); in start_serial_interrupt()
167 int old = inb(speakup_info.port_tts + UART_MCR); in spk_serial_tiocmset()
169 outb((old & ~clear) | set, speakup_info.port_tts + UART_MCR); in spk_serial_tiocmset()
|
| /linux/drivers/ssb/ |
| H A D | driver_extif.c | 46 save_mcr = regs[UART_MCR]; in serial_exists()
47 regs[UART_MCR] = (UART_MCR_LOOP | UART_MCR_OUT2 | UART_MCR_RTS); in serial_exists()
50 regs[UART_MCR] = save_mcr; in serial_exists()
|
| /linux/arch/powerpc/boot/ |
| H A D | ns16550.c | 24 #define UART_MCR 4 /* Out: Modem Control Register */ macro
|
| /linux/drivers/media/rc/ |
| H A D | serial_ir.c | 164 soutp(UART_MCR, hardware[type].off); in on()
166 soutp(UART_MCR, hardware[type].on); in on()
172 soutp(UART_MCR, hardware[type].on); in off()
174 soutp(UART_MCR, hardware[type].off); in off()
|
| /linux/arch/sh/include/asm/ |
| H A D | smc37c93x.h | 63 #define UART_MCR 0x8 /* MODEM Control Register */ macro
|
| /linux/arch/powerpc/platforms/embedded6xx/ |
| H A D | ls_uart.c | 68 out_8(avr_addr + UART_MCR, 0); in avr_uart_configure()
|
| /linux/drivers/tty/serial/ |
| H A D | serial-tegra.c | 201 tegra_uart_write(tup, mcr, UART_MCR); in set_rts()
216 tegra_uart_write(tup, mcr, UART_MCR); in set_dtr()
231 tegra_uart_write(tup, mcr, UART_MCR); in set_loopbk()
955 mcr = tegra_uart_read(tup, UART_MCR); in tegra_uart_hw_deinit()
967 mcr = tegra_uart_read(tup, UART_MCR); in tegra_uart_hw_deinit()
1363 tegra_uart_write(tup, tup->mcr_shadow, UART_MCR); in tegra_uart_set_termios()
1370 tegra_uart_write(tup, tup->mcr_shadow, UART_MCR); in tegra_uart_set_termios()
|
| /linux/include/uapi/linux/ |
| H A D | serial_reg.h | 128 #define UART_MCR 4 /* Out: Modem Control Register */ macro
|
| /linux/samples/vfio-mdev/ |
| H A D | mtty.c | 501 case UART_MCR: in handle_bar_write()
606 (mdev_state->s[index].uart_reg[UART_MCR] & in handle_bar_read()
621 case UART_MCR: in handle_bar_read()
653 if (mdev_state->s[index].uart_reg[UART_MCR] & in handle_bar_read()
|
| /linux/drivers/mmc/core/ |
| H A D | sdio_uart.c | 228 sdio_out(port, UART_MCR, mcr); in sdio_uart_write_mctrl()
|