| /linux/arch/mips/boot/dts/brcm/ |
| H A D | bcm63268-comtrend-vr-3032u.dts | 31 /* GPHY0 Speed 0 */
37 /* GPHY0 Speed 1 */
87 /* EPHY0 Speed */
92 /* EPHY1 Speed */
97 /* EPHY2 Speed */
|
| /linux/drivers/platform/x86/intel/speed_select_if/ |
| H A D | Kconfig | 1 menu "Intel Speed Select Technology interface support"
9 tristate "Intel(R) Speed Select Technology interface drivers"
12 This config enables the Intel(R) Speed Select Technology interface
20 Intel(R) Speed Select Technology features from the user space.
|
| /linux/drivers/net/ethernet/altera/ |
| H A D | Kconfig | 3 tristate "Altera Triple-Speed Ethernet MAC support"
12 This driver supports the Altera Triple-Speed (TSE) Ethernet MAC.
|
| /linux/Documentation/networking/device_drivers/ethernet/intel/ |
| H A D | e1000.rst | 15 - Speed and Duplex Configuration
40 For more information about the AutoNeg, Duplex, and Speed
41 parameters, see the "Speed and Duplex Configuration" section in
58 advertised by the adapter. When this parameter is used, the Speed and
62 Refer to the Speed and Duplex section of this readme for more
243 Speed section in Command Line Parameters
251 Speed forces the line speed to the specified value in megabits per second
254 speed. Duplex should also be set when Speed is set to either 10 or 100.
335 Speed and Duplex Configuration
339 These keywords are Speed, Duplex, and AutoNeg.
[all …]
|
| /linux/Documentation/sound/cards/ |
| H A D | hdspm.rst | 29 * Single Speed -- 1..64 channels
37 * Double Speed -- 1..32 channels
46 * Quad Speed -- 1..16 channels
58 Single Speed -- 32000, 44100, 48000
60 Double Speed -- 64000, 88200, 96000 (untested)
62 Quad Speed -- 128000, 176400, 192000 (untested)
148 Speed-mode or Slave (Autosync). Also see "Preferred Sync Ref"
|
| /linux/drivers/dma/mediatek/ |
| H A D | Kconfig | 4 tristate "MediaTek High-Speed DMA controller support"
9 Enable support for High-Speed DMA controller on MediaTek
|
| /linux/drivers/net/ethernet/oki-semi/pch_gbe/ |
| H A D | pch_gbe_param.c | 43 static int Speed = OPTION_UNSET; variable
44 module_param(Speed, int, 0);
45 MODULE_PARM_DESC(Speed, "Speed setting");
285 speed = Speed; in pch_gbe_check_copper_options()
|
| /linux/drivers/phy/qualcomm/ |
| H A D | Kconfig | 198 tristate "Qualcomm 28nm High-Speed PHY"
204 High-Speed PHY driver. This driver supports the Hi-Speed PHY which
209 tristate "Qualcomm USB Super-Speed PHY driver"
214 Enable this to support the Super-Speed USB transceiver on various
|
| /linux/Documentation/driver-api/ |
| H A D | hsi.rst | 1 High Speed Synchronous Serial Interface (HSI)
7 High Speed Synchronous Interface (HSI) is a full duplex, low latency protocol,
|
| /linux/drivers/phy/xilinx/ |
| H A D | Kconfig | 12 Enable this to support ZynqMP High Speed Gigabit Transceiver
|
| /linux/Documentation/devicetree/bindings/usb/ |
| H A D | usb4604.txt | 1 SMSC USB4604 High-Speed Hub Controller
|
| /linux/drivers/phy/ |
| H A D | Kconfig | 111 schemes. It supports all three USB 2.0 data rates: Low Speed, Full
112 Speed and High Speed.
|
| /linux/Documentation/scsi/ |
| H A D | bnx2fc.rst | 62 Speed: 10 Gbit
63 Supported Speed: 10 Gbit
|
| /linux/Documentation/networking/device_drivers/ethernet/altera/ |
| H A D | altera_tse.rst | 6 Altera Triple-Speed Ethernet MAC driver
11 This is the driver for the Altera Triple-Speed Ethernet (TSE) controllers
24 The Triple-Speed Ethernet, SGDMA, and MSGDMA components are all soft IP
31 Triple-Speed Ethernet instance is using an SGDMA or MSGDMA component. The
61 Altera Triple-Speed Ethernet MAC support (ALTERA_TSE)
154 - Altera Triple Speed Ethernet User Guide, found at http://www.altera.com
|
| /linux/Documentation/ABI/testing/ |
| H A D | sysfs-bus-hsi | 6 High Speed Synchronous Serial Interface (HSI) is a
|
| /linux/arch/arm64/boot/dts/bitmain/ |
| H A D | bm1880-sophon-edge.dts | 16 * LSEC = Low Speed External Connector
17 * HSEC = High Speed External Connector
|
| /linux/Documentation/admin-guide/media/ |
| H A D | dvb-usb-dibusb-mc-cardlist.rst | 23 * - Humax/Coex DVB-T USB Stick 2.0 High Speed
|
| /linux/Documentation/usb/ |
| H A D | ehci.rst | 11 - "High Speed" 480 Mbit/sec (60 MByte/sec)
12 - "Full Speed" 12 Mbit/sec (1.5 MByte/sec)
13 - "Low Speed" 1.5 Mbit/sec
62 High Speed Isochronous (ISO) transfer support is also functional, but
65 Full Speed Isochronous transfer support, through transaction translators,
|
| /linux/Documentation/devicetree/bindings/powerpc/4xx/ |
| H A D | hsta.txt | 2 ppc476gtr High Speed Serial Assist (HSTA) node
|
| /linux/arch/m68k/fpsp040/ |
| H A D | sacos.S | 18 | Speed: The program sCOS takes approximately 310 cycles.
|
| /linux/Documentation/hwmon/ |
| H A D | g760a.rst | 19 The GMT G760A Fan Speed PWM Controller is connected directly to a fan
|
| /linux/Documentation/driver-api/firmware/ |
| H A D | built-in-fw.rst | 17 * Speed
|
| /linux/Documentation/pcmcia/ |
| H A D | devicetable.rst | 37 $ tools/pcmcia/crc32hash "Dual Speed"
|
| /linux/Documentation/watchdog/ |
| H A D | wdt.rst | 51 Fan Speed X o
|
| /linux/arch/arm64/boot/dts/actions/ |
| H A D | s900-bubblegum-96.dts | 72 * LSEC = Low Speed External Connector
73 * HSEC = High Speed External Connector
|