| /linux/drivers/usb/chipidea/ |
| H A D | otg_fsm.h | 21 * Table 4-1: Electrical Characteristics
22 * ->DC Electrical Timing
|
| /linux/Documentation/devicetree/bindings/display/panel/ |
| H A D | tpo,tpg110.yaml | 27 If some electrical strap or alternate resolution is desired,
31 certain electrical driving levels.
|
| H A D | panel-mipi-dbi-spi.yaml | 16 The MIPI Alliance Standard for Display Bus Interface defines the electrical
|
| /linux/Documentation/driver-api/soundwire/ |
| H A D | error_handling.rst | 23 slots) or electrical issues during the transmit/receive transition cannot
35 Slave or to a non-implemented register) or electrical issue, no response
|
| /linux/Documentation/networking/pse-pd/ |
| H A D | introduction.rst | 58 Clause 33 of the IEEE 802.3 standard defines the functional and electrical
67 Clause 104 of the IEEE 802.3 standard delineates the functional and electrical
|
| /linux/Documentation/driver-api/ |
| H A D | miscellaneous.rst | 28 control power supplied to electrical devices.
|
| H A D | i2c.rst | 30 systems are also I2C conformant. The electrical constraints are tighter
|
| H A D | wbrf.rst | 7 Due to electrical and mechanical constraints in certain platform designs
|
| H A D | pin-control.rst | 397 is a way for chip vendors producing some kind of electrical packages to use
702 that your datasheet calls "GPIO mode", but actually is just an electrical
757 software-control a few electrical properties of the pin that you would
777 Here some electrical properties of the pin can be configured no matter
823 - Registers (or fields within registers) that control electrical
844 Electrical properties of the pin such as biasing and drive strength
926 GPIO subsystem. It is just an electrical configuration used by that device
|
| /linux/include/linux/mtd/ |
| H A D | jedec.h | 58 /* electrical parameter block */
|
| H A D | onfi.h | 101 /* electrical parameter block */
|
| /linux/drivers/net/ethernet/intel/e1000e/ |
| H A D | 80003es2lan.h | 64 /* 1=Enable SERDES Electrical Idle */
|
| /linux/Documentation/devicetree/bindings/phy/ |
| H A D | mixel,mipi-dsi-phy.yaml | 15 electrical signals for DSI.
|
| /linux/drivers/net/can/ctucanfd/ |
| H A D | ctucanfd_kframe.h | 16 * Faculty of Electrical Engineering (http://www.fel.cvut.cz)
|
| H A D | ctucanfd.h | 16 * Faculty of Electrical Engineering (http://www.fel.cvut.cz)
|
| H A D | ctucanfd_platform.c | 16 * Faculty of Electrical Engineering (http://www.fel.cvut.cz)
|
| H A D | ctucanfd_kregs.h | 16 * Faculty of Electrical Engineering (http://www.fel.cvut.cz)
|
| /linux/Documentation/i2c/ |
| H A D | summary.rst | 27 meet both SMBus and I2C electrical constraints; and others which can't
|
| /linux/Documentation/i2c/busses/ |
| H A D | i2c-ali15x3.rst | 119 There may be electrical problems on this board.
|
| /linux/Documentation/userspace-api/gpio/ |
| H A D | gpio-get-linehandle-ioctl.rst | 66 the electrical configuration.
|
| H A D | gpio-v2-get-line-ioctl.rst | 64 without altering the electrical configuration.
|
| /linux/Documentation/driver-api/serial/ |
| H A D | serial-rs485.rst | 9 electrical characteristics of drivers and receivers for use in balanced
|
| /linux/drivers/pmdomain/bcm/ |
| H A D | bcm2835-power.c | 205 /* Enable electrical isolation */ in bcm2835_power_power_off()
252 /* Disable electrical isolation */ in bcm2835_power_power_on()
|
| /linux/arch/mips/alchemy/ |
| H A D | board-gpr.c | 210 * The open drain mode is hardwired somewhere or an electrical
|
| /linux/Documentation/networking/device_drivers/can/ctu/ |
| H A D | ctucanfd-driver.rst | 545 `Faculty of Electrical Engineering <http://www.fel.cvut.cz/en/>`_,
558 `Faculty of Electrical Engineering <http://www.fel.cvut.cz/en/>`_,
|