| /freebsd/sys/contrib/device-tree/Bindings/iio/dac/ |
| H A D | adi,ltc2664.yaml | 57 pins (MSP2, MSP1 and MSP0) to GND and/or VCC, any output range can be
61 0 - MPS2=GND, MPS1=GND, MSP0=GND (+-10V, reset to 0V)
62 1 - MPS2=GND, MPS1=GND, MSP0=VCC (+-5V, reset to 0V)
63 2 - MPS2=GND, MPS1=VCC, MSP0=GND (+-2.5V, reset to 0V)
64 3 - MPS2=GND, MPS1=VCC, MSP0=VCC (0V to 10, reset to 0V)
65 4 - MPS2=VCC, MPS1=GND, MSP0=GND (0V to 10V, reset to 5V)
66 5 - MPS2=VCC, MPS1=GND, MSP0=VCC (0V to 5V, reset to 0V)
67 6 - MPS2=VCC, MPS1=VCC, MSP0=GND (0V to 5V, reset to 2.5V)
|
| /freebsd/sys/contrib/device-tree/Bindings/iio/adc/ |
| H A D | ads1015.txt | 12 4: Voltage over AIN0 and GND.
13 5: Voltage over AIN1 and GND.
14 6: Voltage over AIN2 and GND.
15 7: Voltage over AIN3 and GND.
|
| H A D | ti,ads1015.yaml | 61 4: Voltage over AIN0 and GND.
62 5: Voltage over AIN1 and GND.
63 6: Voltage over AIN2 and GND.
64 7: Voltage over AIN3 and GND.
|
| H A D | qcom,spmi-vadc.txt | 89 specified VADC will use the VDD reference (1.8V) and GND for
95 (1.875V) and GND for channel calibration. If property is not found,
|
| H A D | ti-adc12138.txt | 17 (Note that this must not go below GND or exceed vref-p)
|
| H A D | qcom,spmi-vadc.yaml | 112 specified VADC will use the VDD reference (1.8V) and GND for
118 the VDD reference (1.875V) and GND for channel calibration. If
|
| H A D | ti,adc12138.yaml | 40 (Note that this must not go below GND or exceed vref-p)
|
| /freebsd/sys/contrib/device-tree/Bindings/leds/ |
| H A D | leds-lp55xx.txt | 67 GND GND 32h
68 GND VEN 33h
69 VEN GND 34h
|
| /freebsd/sys/contrib/device-tree/Bindings/sound/ |
| H A D | qcom,msm8916-wcd-analog.txt | 46 - qcom,gnd-jack-type-normally-open: boolean, present if gnd pin on jack is
48 its assumed that gnd pin on jack is NC
|
| /freebsd/sys/contrib/device-tree/src/arm64/renesas/ |
| H A D | r8a779g0-white-hawk-ard-audio-da7212.dtso | 37 * | GND (v) pin3 / pin4 |<----->| pin12 / pin14 GND |
41 * (v) These are just sample pins. You can find many 3v3 / GND pins on
|
| H A D | r9a07g043-smarc-pmod.dtso | 15 * | Gnd pin11 |
|
| /freebsd/sys/contrib/device-tree/Bindings/iio/afe/ |
| H A D | temperature-transducer.yaml | 48 | GND
50 GND
|
| H A D | voltage-divider.txt | 21 GND
|
| /freebsd/sys/contrib/device-tree/src/arm/aspeed/ |
| H A D | aspeed-bmc-asrock-e3c256d4i.dts | 319 &pinctrl_adc13_default /* GND */
320 &pinctrl_adc14_default /* GND */
321 &pinctrl_adc15_default>; /* GND */
|
| /freebsd/share/man/man4/ |
| H A D | lpbb.4 | 49 | 12 o-+--+ | | 3|\\ 4 | | | (Gnd) | GND |
|
| /freebsd/sys/contrib/device-tree/Bindings/hwmon/ |
| H A D | ntc-thermistor.yaml | 45 + GND GND
|
| /freebsd/sys/contrib/device-tree/src/arm64/nvidia/ |
| H A D | tegra186-p3310.dtsi | 397 gnd: regulator-gnd { label
399 regulator-name = "GND";
|
| H A D | tegra186-p3509-0000+p3636-0001.dts | 621 vddio-hsic-supply = <&gnd>;
1080 gnd: regulator-gnd { label
1082 regulator-name = "GND";
|
| /freebsd/sys/contrib/device-tree/Bindings/mtd/ |
| H A D | jedec,spi-nor.yaml | 87 flash device is not connected or is wrongly tied to GND (that includes internal
90 the SRWD bit while writing the status register. WP# signal hard strapped to GND
|
| /freebsd/sys/contrib/device-tree/Bindings/iio/proximity/ |
| H A D | semtech,sx9324.yaml | 137 - gnd
201 semtech,cs-idle-sleep = "gnd";
|
| /freebsd/sys/contrib/device-tree/Bindings/mfd/ |
| H A D | rohm,bd71815-pmic.yaml | 76 The BD71815 has undocumented GPO at pin E5. Pin is marked as GND at the
77 data-sheet as its location in the middle of GND pins makes it hard to
|
| /freebsd/sys/contrib/device-tree/Bindings/mmc/ |
| H A D | sdhci-atmel.txt | 22 For instance on SAMA5D2, the pin is usually tied to the GND with a resistor
|
| H A D | atmel,sama5d2-sdhci.yaml | 53 SAMA5D2, the pin is usually tied to the GND with a resistor and a
|
| /freebsd/sys/contrib/device-tree/include/dt-bindings/sound/ |
| H A D | cs42l42.h | 19 /* HPOUT Clamp to GND Override */
|
| /freebsd/sys/contrib/device-tree/Bindings/gpio/ |
| H A D | gpio-delay.yaml | 30 GND
|