1 // SPDX-License-Identifier: GPL-2.0-only
2 /*
3 * Copyright (c) 2016-2017, 2019, The Linux Foundation. All rights reserved.
4 * Copyright (c) 2022 Linaro Limited.
5 * Author: Caleb Connolly <caleb.connolly@linaro.org>
6 *
7 * This driver is for the Round Robin ADC found in the pmi8998 and pm660 PMICs.
8 */
9
10 #include <linux/bitfield.h>
11 #include <linux/delay.h>
12 #include <linux/kernel.h>
13 #include <linux/math64.h>
14 #include <linux/module.h>
15 #include <linux/mod_devicetable.h>
16 #include <linux/platform_device.h>
17 #include <linux/property.h>
18 #include <linux/regmap.h>
19 #include <linux/spmi.h>
20 #include <linux/types.h>
21 #include <linux/units.h>
22
23 #include <linux/unaligned.h>
24
25 #include <linux/iio/iio.h>
26 #include <linux/iio/types.h>
27
28 #include <soc/qcom/qcom-spmi-pmic.h>
29
30 #define DRIVER_NAME "qcom-spmi-rradc"
31
32 #define RR_ADC_EN_CTL 0x46
33 #define RR_ADC_SKIN_TEMP_LSB 0x50
34 #define RR_ADC_SKIN_TEMP_MSB 0x51
35 #define RR_ADC_CTL 0x52
36 #define RR_ADC_CTL_CONTINUOUS_SEL BIT(3)
37 #define RR_ADC_LOG 0x53
38 #define RR_ADC_LOG_CLR_CTRL BIT(0)
39
40 #define RR_ADC_FAKE_BATT_LOW_LSB 0x58
41 #define RR_ADC_FAKE_BATT_LOW_MSB 0x59
42 #define RR_ADC_FAKE_BATT_HIGH_LSB 0x5A
43 #define RR_ADC_FAKE_BATT_HIGH_MSB 0x5B
44
45 #define RR_ADC_BATT_ID_CTRL 0x60
46 #define RR_ADC_BATT_ID_CTRL_CHANNEL_CONV BIT(0)
47 #define RR_ADC_BATT_ID_TRIGGER 0x61
48 #define RR_ADC_BATT_ID_STS 0x62
49 #define RR_ADC_BATT_ID_CFG 0x63
50 #define BATT_ID_SETTLE_MASK GENMASK(7, 5)
51 #define RR_ADC_BATT_ID_5_LSB 0x66
52 #define RR_ADC_BATT_ID_5_MSB 0x67
53 #define RR_ADC_BATT_ID_15_LSB 0x68
54 #define RR_ADC_BATT_ID_15_MSB 0x69
55 #define RR_ADC_BATT_ID_150_LSB 0x6A
56 #define RR_ADC_BATT_ID_150_MSB 0x6B
57
58 #define RR_ADC_BATT_THERM_CTRL 0x70
59 #define RR_ADC_BATT_THERM_TRIGGER 0x71
60 #define RR_ADC_BATT_THERM_STS 0x72
61 #define RR_ADC_BATT_THERM_CFG 0x73
62 #define RR_ADC_BATT_THERM_LSB 0x74
63 #define RR_ADC_BATT_THERM_MSB 0x75
64 #define RR_ADC_BATT_THERM_FREQ 0x76
65
66 #define RR_ADC_AUX_THERM_CTRL 0x80
67 #define RR_ADC_AUX_THERM_TRIGGER 0x81
68 #define RR_ADC_AUX_THERM_STS 0x82
69 #define RR_ADC_AUX_THERM_CFG 0x83
70 #define RR_ADC_AUX_THERM_LSB 0x84
71 #define RR_ADC_AUX_THERM_MSB 0x85
72
73 #define RR_ADC_SKIN_HOT 0x86
74 #define RR_ADC_SKIN_TOO_HOT 0x87
75
76 #define RR_ADC_AUX_THERM_C1 0x88
77 #define RR_ADC_AUX_THERM_C2 0x89
78 #define RR_ADC_AUX_THERM_C3 0x8A
79 #define RR_ADC_AUX_THERM_HALF_RANGE 0x8B
80
81 #define RR_ADC_USB_IN_V_CTRL 0x90
82 #define RR_ADC_USB_IN_V_TRIGGER 0x91
83 #define RR_ADC_USB_IN_V_STS 0x92
84 #define RR_ADC_USB_IN_V_LSB 0x94
85 #define RR_ADC_USB_IN_V_MSB 0x95
86 #define RR_ADC_USB_IN_I_CTRL 0x98
87 #define RR_ADC_USB_IN_I_TRIGGER 0x99
88 #define RR_ADC_USB_IN_I_STS 0x9A
89 #define RR_ADC_USB_IN_I_LSB 0x9C
90 #define RR_ADC_USB_IN_I_MSB 0x9D
91
92 #define RR_ADC_DC_IN_V_CTRL 0xA0
93 #define RR_ADC_DC_IN_V_TRIGGER 0xA1
94 #define RR_ADC_DC_IN_V_STS 0xA2
95 #define RR_ADC_DC_IN_V_LSB 0xA4
96 #define RR_ADC_DC_IN_V_MSB 0xA5
97 #define RR_ADC_DC_IN_I_CTRL 0xA8
98 #define RR_ADC_DC_IN_I_TRIGGER 0xA9
99 #define RR_ADC_DC_IN_I_STS 0xAA
100 #define RR_ADC_DC_IN_I_LSB 0xAC
101 #define RR_ADC_DC_IN_I_MSB 0xAD
102
103 #define RR_ADC_PMI_DIE_TEMP_CTRL 0xB0
104 #define RR_ADC_PMI_DIE_TEMP_TRIGGER 0xB1
105 #define RR_ADC_PMI_DIE_TEMP_STS 0xB2
106 #define RR_ADC_PMI_DIE_TEMP_CFG 0xB3
107 #define RR_ADC_PMI_DIE_TEMP_LSB 0xB4
108 #define RR_ADC_PMI_DIE_TEMP_MSB 0xB5
109
110 #define RR_ADC_CHARGER_TEMP_CTRL 0xB8
111 #define RR_ADC_CHARGER_TEMP_TRIGGER 0xB9
112 #define RR_ADC_CHARGER_TEMP_STS 0xBA
113 #define RR_ADC_CHARGER_TEMP_CFG 0xBB
114 #define RR_ADC_CHARGER_TEMP_LSB 0xBC
115 #define RR_ADC_CHARGER_TEMP_MSB 0xBD
116 #define RR_ADC_CHARGER_HOT 0xBE
117 #define RR_ADC_CHARGER_TOO_HOT 0xBF
118
119 #define RR_ADC_GPIO_CTRL 0xC0
120 #define RR_ADC_GPIO_TRIGGER 0xC1
121 #define RR_ADC_GPIO_STS 0xC2
122 #define RR_ADC_GPIO_LSB 0xC4
123 #define RR_ADC_GPIO_MSB 0xC5
124
125 #define RR_ADC_ATEST_CTRL 0xC8
126 #define RR_ADC_ATEST_TRIGGER 0xC9
127 #define RR_ADC_ATEST_STS 0xCA
128 #define RR_ADC_ATEST_LSB 0xCC
129 #define RR_ADC_ATEST_MSB 0xCD
130 #define RR_ADC_SEC_ACCESS 0xD0
131
132 #define RR_ADC_PERPH_RESET_CTL2 0xD9
133 #define RR_ADC_PERPH_RESET_CTL3 0xDA
134 #define RR_ADC_PERPH_RESET_CTL4 0xDB
135 #define RR_ADC_INT_TEST1 0xE0
136 #define RR_ADC_INT_TEST_VAL 0xE1
137
138 #define RR_ADC_TM_TRIGGER_CTRLS 0xE2
139 #define RR_ADC_TM_ADC_CTRLS 0xE3
140 #define RR_ADC_TM_CNL_CTRL 0xE4
141 #define RR_ADC_TM_BATT_ID_CTRL 0xE5
142 #define RR_ADC_TM_THERM_CTRL 0xE6
143 #define RR_ADC_TM_CONV_STS 0xE7
144 #define RR_ADC_TM_ADC_READ_LSB 0xE8
145 #define RR_ADC_TM_ADC_READ_MSB 0xE9
146 #define RR_ADC_TM_ATEST_MUX_1 0xEA
147 #define RR_ADC_TM_ATEST_MUX_2 0xEB
148 #define RR_ADC_TM_REFERENCES 0xED
149 #define RR_ADC_TM_MISC_CTL 0xEE
150 #define RR_ADC_TM_RR_CTRL 0xEF
151
152 #define RR_ADC_TRIGGER_EVERY_CYCLE BIT(7)
153 #define RR_ADC_TRIGGER_CTL BIT(0)
154
155 #define RR_ADC_BATT_ID_RANGE 820
156
157 #define RR_ADC_BITS 10
158 #define RR_ADC_CHAN_MSB (1 << RR_ADC_BITS)
159 #define RR_ADC_FS_VOLTAGE_MV 2500
160
161 /* BATT_THERM 0.25K/LSB */
162 #define RR_ADC_BATT_THERM_LSB_K 4
163
164 #define RR_ADC_TEMP_FS_VOLTAGE_NUM 5000000
165 #define RR_ADC_TEMP_FS_VOLTAGE_DEN 3
166 #define RR_ADC_DIE_TEMP_OFFSET 601400
167 #define RR_ADC_DIE_TEMP_SLOPE 2
168 #define RR_ADC_DIE_TEMP_OFFSET_MILLI_DEGC 25000
169
170 #define RR_ADC_CHG_TEMP_GF_OFFSET_UV 1303168
171 #define RR_ADC_CHG_TEMP_GF_SLOPE_UV_PER_C 3784
172 #define RR_ADC_CHG_TEMP_SMIC_OFFSET_UV 1338433
173 #define RR_ADC_CHG_TEMP_SMIC_SLOPE_UV_PER_C 3655
174 #define RR_ADC_CHG_TEMP_660_GF_OFFSET_UV 1309001
175 #define RR_ADC_CHG_TEMP_660_GF_SLOPE_UV_PER_C 3403
176 #define RR_ADC_CHG_TEMP_660_SMIC_OFFSET_UV 1295898
177 #define RR_ADC_CHG_TEMP_660_SMIC_SLOPE_UV_PER_C 3596
178 #define RR_ADC_CHG_TEMP_660_MGNA_OFFSET_UV 1314779
179 #define RR_ADC_CHG_TEMP_660_MGNA_SLOPE_UV_PER_C 3496
180 #define RR_ADC_CHG_TEMP_OFFSET_MILLI_DEGC 25000
181 #define RR_ADC_CHG_THRESHOLD_SCALE 4
182
183 #define RR_ADC_VOLT_INPUT_FACTOR 8
184 #define RR_ADC_CURR_INPUT_FACTOR 2000
185 #define RR_ADC_CURR_USBIN_INPUT_FACTOR_MIL 1886
186 #define RR_ADC_CURR_USBIN_660_FACTOR_MIL 9
187 #define RR_ADC_CURR_USBIN_660_UV_VAL 579500
188
189 #define RR_ADC_GPIO_FS_RANGE 5000
190 #define RR_ADC_COHERENT_CHECK_RETRY 5
191 #define RR_ADC_CHAN_MAX_CONTINUOUS_BUFFER_LEN 16
192
193 #define RR_ADC_STS_CHANNEL_READING_MASK GENMASK(1, 0)
194 #define RR_ADC_STS_CHANNEL_STS BIT(1)
195
196 #define RR_ADC_TP_REV_VERSION1 21
197 #define RR_ADC_TP_REV_VERSION2 29
198 #define RR_ADC_TP_REV_VERSION3 32
199
200 #define RRADC_BATT_ID_DELAY_MAX 8
201
202 enum rradc_channel_id {
203 RR_ADC_BATT_ID = 0,
204 RR_ADC_BATT_THERM,
205 RR_ADC_SKIN_TEMP,
206 RR_ADC_USBIN_I,
207 RR_ADC_USBIN_V,
208 RR_ADC_DCIN_I,
209 RR_ADC_DCIN_V,
210 RR_ADC_DIE_TEMP,
211 RR_ADC_CHG_TEMP,
212 RR_ADC_GPIO,
213 RR_ADC_CHAN_MAX
214 };
215
216 struct rradc_chip;
217
218 /**
219 * struct rradc_channel - rradc channel data
220 * @label: channel label
221 * @lsb: Channel least significant byte
222 * @status: Channel status address
223 * @size: number of bytes to read
224 * @trigger_addr: Trigger address, trigger is only used on some channels
225 * @trigger_mask: Trigger mask
226 * @scale_fn: Post process callback for channels which can't be exposed
227 * as offset + scale.
228 */
229 struct rradc_channel {
230 const char *label;
231 u8 lsb;
232 u8 status;
233 int size;
234 int trigger_addr;
235 int trigger_mask;
236 int (*scale_fn)(struct rradc_chip *chip, u16 adc_code, int *result);
237 };
238
239 struct rradc_chip {
240 struct device *dev;
241 const struct qcom_spmi_pmic *pmic;
242 /*
243 * Lock held while doing channel conversion
244 * involving multiple register read/writes
245 */
246 struct mutex conversion_lock;
247 struct regmap *regmap;
248 u32 base;
249 int batt_id_delay;
250 u16 batt_id_data;
251 };
252
253 static const int batt_id_delays[] = { 0, 1, 4, 12, 20, 40, 60, 80 };
254 static const struct rradc_channel rradc_chans[RR_ADC_CHAN_MAX];
255 static const struct iio_chan_spec rradc_iio_chans[RR_ADC_CHAN_MAX];
256
rradc_read(struct rradc_chip * chip,u16 addr,__le16 * buf,int len)257 static int rradc_read(struct rradc_chip *chip, u16 addr, __le16 *buf, int len)
258 {
259 int ret, retry_cnt = 0;
260 __le16 data_check[RR_ADC_CHAN_MAX_CONTINUOUS_BUFFER_LEN / 2];
261
262 if (len > RR_ADC_CHAN_MAX_CONTINUOUS_BUFFER_LEN) {
263 dev_err(chip->dev,
264 "Can't read more than %d bytes, but asked to read %d bytes.\n",
265 RR_ADC_CHAN_MAX_CONTINUOUS_BUFFER_LEN, len);
266 return -EINVAL;
267 }
268
269 while (retry_cnt < RR_ADC_COHERENT_CHECK_RETRY) {
270 ret = regmap_bulk_read(chip->regmap, chip->base + addr, buf,
271 len);
272 if (ret < 0) {
273 dev_err(chip->dev, "rr_adc reg 0x%x failed :%d\n", addr,
274 ret);
275 return ret;
276 }
277
278 ret = regmap_bulk_read(chip->regmap, chip->base + addr,
279 data_check, len);
280 if (ret < 0) {
281 dev_err(chip->dev, "rr_adc reg 0x%x failed :%d\n", addr,
282 ret);
283 return ret;
284 }
285
286 if (memcmp(buf, data_check, len) != 0) {
287 retry_cnt++;
288 dev_dbg(chip->dev,
289 "coherent read error, retry_cnt:%d\n",
290 retry_cnt);
291 continue;
292 }
293
294 break;
295 }
296
297 if (retry_cnt == RR_ADC_COHERENT_CHECK_RETRY)
298 dev_err(chip->dev, "Retry exceeded for coherency check\n");
299
300 return ret;
301 }
302
rradc_get_fab_coeff(struct rradc_chip * chip,int64_t * offset,int64_t * slope)303 static int rradc_get_fab_coeff(struct rradc_chip *chip, int64_t *offset,
304 int64_t *slope)
305 {
306 if (chip->pmic->subtype == PM660_SUBTYPE) {
307 switch (chip->pmic->fab_id) {
308 case PM660_FAB_ID_GF:
309 *offset = RR_ADC_CHG_TEMP_660_GF_OFFSET_UV;
310 *slope = RR_ADC_CHG_TEMP_660_GF_SLOPE_UV_PER_C;
311 return 0;
312 case PM660_FAB_ID_TSMC:
313 *offset = RR_ADC_CHG_TEMP_660_SMIC_OFFSET_UV;
314 *slope = RR_ADC_CHG_TEMP_660_SMIC_SLOPE_UV_PER_C;
315 return 0;
316 default:
317 *offset = RR_ADC_CHG_TEMP_660_MGNA_OFFSET_UV;
318 *slope = RR_ADC_CHG_TEMP_660_MGNA_SLOPE_UV_PER_C;
319 }
320 } else if (chip->pmic->subtype == PMI8998_SUBTYPE) {
321 switch (chip->pmic->fab_id) {
322 case PMI8998_FAB_ID_GF:
323 *offset = RR_ADC_CHG_TEMP_GF_OFFSET_UV;
324 *slope = RR_ADC_CHG_TEMP_GF_SLOPE_UV_PER_C;
325 return 0;
326 case PMI8998_FAB_ID_SMIC:
327 *offset = RR_ADC_CHG_TEMP_SMIC_OFFSET_UV;
328 *slope = RR_ADC_CHG_TEMP_SMIC_SLOPE_UV_PER_C;
329 return 0;
330 default:
331 return -EINVAL;
332 }
333 }
334
335 return -EINVAL;
336 }
337
338 /*
339 * These functions explicitly cast int64_t to int.
340 * They will never overflow, as the values are small enough.
341 */
rradc_post_process_batt_id(struct rradc_chip * chip,u16 adc_code,int * result_ohms)342 static int rradc_post_process_batt_id(struct rradc_chip *chip, u16 adc_code,
343 int *result_ohms)
344 {
345 uint32_t current_value;
346 int64_t r_id;
347
348 current_value = chip->batt_id_data;
349 r_id = ((int64_t)adc_code * RR_ADC_FS_VOLTAGE_MV);
350 r_id = div64_s64(r_id, (RR_ADC_CHAN_MSB * current_value));
351 *result_ohms = (int)(r_id * MILLI);
352
353 return 0;
354 }
355
rradc_enable_continuous_mode(struct rradc_chip * chip)356 static int rradc_enable_continuous_mode(struct rradc_chip *chip)
357 {
358 int ret;
359
360 /* Clear channel log */
361 ret = regmap_set_bits(chip->regmap, chip->base + RR_ADC_LOG,
362 RR_ADC_LOG_CLR_CTRL);
363 if (ret < 0) {
364 dev_err(chip->dev, "log ctrl update to clear failed:%d\n", ret);
365 return ret;
366 }
367
368 ret = regmap_clear_bits(chip->regmap, chip->base + RR_ADC_LOG,
369 RR_ADC_LOG_CLR_CTRL);
370 if (ret < 0) {
371 dev_err(chip->dev, "log ctrl update to not clear failed:%d\n",
372 ret);
373 return ret;
374 }
375
376 /* Switch to continuous mode */
377 ret = regmap_set_bits(chip->regmap, chip->base + RR_ADC_CTL,
378 RR_ADC_CTL_CONTINUOUS_SEL);
379 if (ret < 0)
380 dev_err(chip->dev, "Update to continuous mode failed:%d\n",
381 ret);
382
383 return ret;
384 }
385
rradc_disable_continuous_mode(struct rradc_chip * chip)386 static int rradc_disable_continuous_mode(struct rradc_chip *chip)
387 {
388 int ret;
389
390 /* Switch to non continuous mode */
391 ret = regmap_clear_bits(chip->regmap, chip->base + RR_ADC_CTL,
392 RR_ADC_CTL_CONTINUOUS_SEL);
393 if (ret < 0)
394 dev_err(chip->dev, "Update to non-continuous mode failed:%d\n",
395 ret);
396
397 return ret;
398 }
399
rradc_is_ready(struct rradc_chip * chip,enum rradc_channel_id chan_address)400 static bool rradc_is_ready(struct rradc_chip *chip,
401 enum rradc_channel_id chan_address)
402 {
403 const struct rradc_channel *chan = &rradc_chans[chan_address];
404 int ret;
405 unsigned int status, mask;
406
407 /* BATT_ID STS bit does not get set initially */
408 switch (chan_address) {
409 case RR_ADC_BATT_ID:
410 mask = RR_ADC_STS_CHANNEL_STS;
411 break;
412 default:
413 mask = RR_ADC_STS_CHANNEL_READING_MASK;
414 break;
415 }
416
417 ret = regmap_read(chip->regmap, chip->base + chan->status, &status);
418 if (ret < 0 || !(status & mask))
419 return false;
420
421 return true;
422 }
423
rradc_read_status_in_cont_mode(struct rradc_chip * chip,enum rradc_channel_id chan_address)424 static int rradc_read_status_in_cont_mode(struct rradc_chip *chip,
425 enum rradc_channel_id chan_address)
426 {
427 const struct rradc_channel *chan = &rradc_chans[chan_address];
428 const struct iio_chan_spec *iio_chan = &rradc_iio_chans[chan_address];
429 int ret, i;
430
431 if (chan->trigger_mask == 0) {
432 dev_err(chip->dev, "Channel doesn't have a trigger mask\n");
433 return -EINVAL;
434 }
435
436 ret = regmap_set_bits(chip->regmap, chip->base + chan->trigger_addr,
437 chan->trigger_mask);
438 if (ret < 0) {
439 dev_err(chip->dev,
440 "Failed to apply trigger for channel '%s' ret=%d\n",
441 iio_chan->extend_name, ret);
442 return ret;
443 }
444
445 ret = rradc_enable_continuous_mode(chip);
446 if (ret < 0) {
447 dev_err(chip->dev, "Failed to switch to continuous mode\n");
448 goto disable_trigger;
449 }
450
451 /*
452 * The wait/sleep values were found through trial and error,
453 * this is mostly for the battery ID channel which takes some
454 * time to settle.
455 */
456 for (i = 0; i < 5; i++) {
457 if (rradc_is_ready(chip, chan_address))
458 break;
459 usleep_range(50000, 50000 + 500);
460 }
461
462 if (i == 5) {
463 dev_err(chip->dev, "Channel '%s' is not ready\n",
464 iio_chan->extend_name);
465 ret = -ETIMEDOUT;
466 }
467
468 rradc_disable_continuous_mode(chip);
469
470 disable_trigger:
471 regmap_clear_bits(chip->regmap, chip->base + chan->trigger_addr,
472 chan->trigger_mask);
473
474 return ret;
475 }
476
rradc_prepare_batt_id_conversion(struct rradc_chip * chip,enum rradc_channel_id chan_address,u16 * data)477 static int rradc_prepare_batt_id_conversion(struct rradc_chip *chip,
478 enum rradc_channel_id chan_address,
479 u16 *data)
480 {
481 int ret;
482
483 ret = regmap_set_bits(chip->regmap, chip->base + RR_ADC_BATT_ID_CTRL,
484 RR_ADC_BATT_ID_CTRL_CHANNEL_CONV);
485 if (ret < 0) {
486 dev_err(chip->dev, "Enabling BATT ID channel failed:%d\n", ret);
487 return ret;
488 }
489
490 ret = regmap_set_bits(chip->regmap,
491 chip->base + RR_ADC_BATT_ID_TRIGGER,
492 RR_ADC_TRIGGER_CTL);
493 if (ret < 0) {
494 dev_err(chip->dev, "BATT_ID trigger set failed:%d\n", ret);
495 goto out_disable_batt_id;
496 }
497
498 ret = rradc_read_status_in_cont_mode(chip, chan_address);
499
500 /* Reset registers back to default values */
501 regmap_clear_bits(chip->regmap, chip->base + RR_ADC_BATT_ID_TRIGGER,
502 RR_ADC_TRIGGER_CTL);
503
504 out_disable_batt_id:
505 regmap_clear_bits(chip->regmap, chip->base + RR_ADC_BATT_ID_CTRL,
506 RR_ADC_BATT_ID_CTRL_CHANNEL_CONV);
507
508 return ret;
509 }
510
rradc_do_conversion(struct rradc_chip * chip,enum rradc_channel_id chan_address,u16 * data)511 static int rradc_do_conversion(struct rradc_chip *chip,
512 enum rradc_channel_id chan_address, u16 *data)
513 {
514 const struct rradc_channel *chan = &rradc_chans[chan_address];
515 const struct iio_chan_spec *iio_chan = &rradc_iio_chans[chan_address];
516 int ret;
517 __le16 buf[3];
518
519 mutex_lock(&chip->conversion_lock);
520
521 switch (chan_address) {
522 case RR_ADC_BATT_ID:
523 ret = rradc_prepare_batt_id_conversion(chip, chan_address, data);
524 if (ret < 0) {
525 dev_err(chip->dev, "Battery ID conversion failed:%d\n",
526 ret);
527 goto unlock_out;
528 }
529 break;
530
531 case RR_ADC_USBIN_V:
532 case RR_ADC_DIE_TEMP:
533 ret = rradc_read_status_in_cont_mode(chip, chan_address);
534 if (ret < 0) {
535 dev_err(chip->dev,
536 "Error reading in continuous mode:%d\n", ret);
537 goto unlock_out;
538 }
539 break;
540 default:
541 if (!rradc_is_ready(chip, chan_address)) {
542 /*
543 * Usually this means the channel isn't attached, for example
544 * the in_voltage_usbin_v_input channel will not be ready if
545 * no USB cable is attached
546 */
547 dev_dbg(chip->dev, "channel '%s' is not ready\n",
548 iio_chan->extend_name);
549 ret = -ENODATA;
550 goto unlock_out;
551 }
552 break;
553 }
554
555 ret = rradc_read(chip, chan->lsb, buf, chan->size);
556 if (ret) {
557 dev_err(chip->dev, "read data failed\n");
558 goto unlock_out;
559 }
560
561 /*
562 * For the battery ID we read the register for every ID ADC and then
563 * see which one is actually connected.
564 */
565 if (chan_address == RR_ADC_BATT_ID) {
566 u16 batt_id_150 = le16_to_cpu(buf[2]);
567 u16 batt_id_15 = le16_to_cpu(buf[1]);
568 u16 batt_id_5 = le16_to_cpu(buf[0]);
569
570 if (!batt_id_150 && !batt_id_15 && !batt_id_5) {
571 dev_err(chip->dev,
572 "Invalid batt_id values with all zeros\n");
573 ret = -EINVAL;
574 goto unlock_out;
575 }
576
577 if (batt_id_150 <= RR_ADC_BATT_ID_RANGE) {
578 *data = batt_id_150;
579 chip->batt_id_data = 150;
580 } else if (batt_id_15 <= RR_ADC_BATT_ID_RANGE) {
581 *data = batt_id_15;
582 chip->batt_id_data = 15;
583 } else {
584 *data = batt_id_5;
585 chip->batt_id_data = 5;
586 }
587 } else {
588 /*
589 * All of the other channels are either 1 or 2 bytes.
590 * We can rely on the second byte being 0 for 1-byte channels.
591 */
592 *data = le16_to_cpu(buf[0]);
593 }
594
595 unlock_out:
596 mutex_unlock(&chip->conversion_lock);
597
598 return ret;
599 }
600
rradc_read_scale(struct rradc_chip * chip,int chan_address,int * val,int * val2)601 static int rradc_read_scale(struct rradc_chip *chip, int chan_address, int *val,
602 int *val2)
603 {
604 int64_t fab_offset, fab_slope;
605 int ret;
606
607 ret = rradc_get_fab_coeff(chip, &fab_offset, &fab_slope);
608 if (ret < 0) {
609 dev_err(chip->dev, "Unable to get fab id coefficients\n");
610 return -EINVAL;
611 }
612
613 switch (chan_address) {
614 case RR_ADC_SKIN_TEMP:
615 *val = MILLI;
616 *val2 = RR_ADC_BATT_THERM_LSB_K;
617 return IIO_VAL_FRACTIONAL;
618 case RR_ADC_USBIN_I:
619 *val = RR_ADC_CURR_USBIN_INPUT_FACTOR_MIL *
620 RR_ADC_FS_VOLTAGE_MV;
621 *val2 = RR_ADC_CHAN_MSB;
622 return IIO_VAL_FRACTIONAL;
623 case RR_ADC_DCIN_I:
624 *val = RR_ADC_CURR_INPUT_FACTOR * RR_ADC_FS_VOLTAGE_MV;
625 *val2 = RR_ADC_CHAN_MSB;
626 return IIO_VAL_FRACTIONAL;
627 case RR_ADC_USBIN_V:
628 case RR_ADC_DCIN_V:
629 *val = RR_ADC_VOLT_INPUT_FACTOR * RR_ADC_FS_VOLTAGE_MV * MILLI;
630 *val2 = RR_ADC_CHAN_MSB;
631 return IIO_VAL_FRACTIONAL;
632 case RR_ADC_GPIO:
633 *val = RR_ADC_GPIO_FS_RANGE;
634 *val2 = RR_ADC_CHAN_MSB;
635 return IIO_VAL_FRACTIONAL;
636 case RR_ADC_CHG_TEMP:
637 /*
638 * We divide val2 by MILLI instead of multiplying val
639 * to avoid an integer overflow.
640 */
641 *val = -RR_ADC_TEMP_FS_VOLTAGE_NUM;
642 *val2 = div64_s64(RR_ADC_TEMP_FS_VOLTAGE_DEN * RR_ADC_CHAN_MSB *
643 fab_slope,
644 MILLI);
645
646 return IIO_VAL_FRACTIONAL;
647 case RR_ADC_DIE_TEMP:
648 *val = RR_ADC_TEMP_FS_VOLTAGE_NUM;
649 *val2 = RR_ADC_TEMP_FS_VOLTAGE_DEN * RR_ADC_CHAN_MSB *
650 RR_ADC_DIE_TEMP_SLOPE;
651
652 return IIO_VAL_FRACTIONAL;
653 default:
654 return -EINVAL;
655 }
656 }
657
rradc_read_offset(struct rradc_chip * chip,int chan_address,int * val)658 static int rradc_read_offset(struct rradc_chip *chip, int chan_address, int *val)
659 {
660 int64_t fab_offset, fab_slope;
661 int64_t offset1, offset2;
662 int ret;
663
664 switch (chan_address) {
665 case RR_ADC_SKIN_TEMP:
666 /*
667 * Offset from kelvin to degC, divided by the
668 * scale factor (250). We lose some precision here.
669 * 273150 / 250 = 1092.6
670 */
671 *val = div64_s64(ABSOLUTE_ZERO_MILLICELSIUS,
672 (MILLI / RR_ADC_BATT_THERM_LSB_K));
673 return IIO_VAL_INT;
674 case RR_ADC_CHG_TEMP:
675 ret = rradc_get_fab_coeff(chip, &fab_offset, &fab_slope);
676 if (ret < 0) {
677 dev_err(chip->dev,
678 "Unable to get fab id coefficients\n");
679 return -EINVAL;
680 }
681 offset1 = -(fab_offset * RR_ADC_TEMP_FS_VOLTAGE_DEN *
682 RR_ADC_CHAN_MSB);
683 offset1 += (int64_t)RR_ADC_TEMP_FS_VOLTAGE_NUM / 2ULL;
684 offset1 = div64_s64(offset1,
685 (int64_t)(RR_ADC_TEMP_FS_VOLTAGE_NUM));
686
687 offset2 = (int64_t)RR_ADC_CHG_TEMP_OFFSET_MILLI_DEGC *
688 RR_ADC_TEMP_FS_VOLTAGE_DEN * RR_ADC_CHAN_MSB *
689 (int64_t)fab_slope;
690 offset2 += ((int64_t)MILLI * RR_ADC_TEMP_FS_VOLTAGE_NUM) / 2;
691 offset2 = div64_s64(
692 offset2, ((int64_t)MILLI * RR_ADC_TEMP_FS_VOLTAGE_NUM));
693
694 /*
695 * The -1 is to compensate for lost precision.
696 * It should actually be -0.7906976744186046.
697 * This works out to every value being off
698 * by about +0.091 degrees C after applying offset and scale.
699 */
700 *val = (int)(offset1 - offset2 - 1);
701 return IIO_VAL_INT;
702 case RR_ADC_DIE_TEMP:
703 offset1 = -RR_ADC_DIE_TEMP_OFFSET *
704 (int64_t)RR_ADC_TEMP_FS_VOLTAGE_DEN *
705 (int64_t)RR_ADC_CHAN_MSB;
706 offset1 = div64_s64(offset1, RR_ADC_TEMP_FS_VOLTAGE_NUM);
707
708 offset2 = -(int64_t)RR_ADC_CHG_TEMP_OFFSET_MILLI_DEGC *
709 RR_ADC_TEMP_FS_VOLTAGE_DEN * RR_ADC_CHAN_MSB *
710 RR_ADC_DIE_TEMP_SLOPE;
711 offset2 = div64_s64(offset2,
712 ((int64_t)RR_ADC_TEMP_FS_VOLTAGE_NUM));
713
714 /*
715 * The result is -339, it should be -338.69789, this results
716 * in the calculated die temp being off by
717 * -0.004 - -0.0175 degrees C
718 */
719 *val = (int)(offset1 - offset2);
720 return IIO_VAL_INT;
721 default:
722 break;
723 }
724 return -EINVAL;
725 }
726
rradc_read_raw(struct iio_dev * indio_dev,struct iio_chan_spec const * chan_spec,int * val,int * val2,long mask)727 static int rradc_read_raw(struct iio_dev *indio_dev,
728 struct iio_chan_spec const *chan_spec, int *val,
729 int *val2, long mask)
730 {
731 struct rradc_chip *chip = iio_priv(indio_dev);
732 const struct rradc_channel *chan;
733 int ret;
734 u16 adc_code;
735
736 if (chan_spec->address >= RR_ADC_CHAN_MAX) {
737 dev_err(chip->dev, "Invalid channel index:%lu\n",
738 chan_spec->address);
739 return -EINVAL;
740 }
741
742 switch (mask) {
743 case IIO_CHAN_INFO_SCALE:
744 return rradc_read_scale(chip, chan_spec->address, val, val2);
745 case IIO_CHAN_INFO_OFFSET:
746 return rradc_read_offset(chip, chan_spec->address, val);
747 case IIO_CHAN_INFO_RAW:
748 ret = rradc_do_conversion(chip, chan_spec->address, &adc_code);
749 if (ret < 0)
750 return ret;
751
752 *val = adc_code;
753 return IIO_VAL_INT;
754 case IIO_CHAN_INFO_PROCESSED:
755 chan = &rradc_chans[chan_spec->address];
756 if (!chan->scale_fn)
757 return -EINVAL;
758 ret = rradc_do_conversion(chip, chan_spec->address, &adc_code);
759 if (ret < 0)
760 return ret;
761
762 *val = chan->scale_fn(chip, adc_code, val);
763 return IIO_VAL_INT;
764 default:
765 return -EINVAL;
766 }
767 }
768
rradc_read_label(struct iio_dev * indio_dev,struct iio_chan_spec const * chan,char * label)769 static int rradc_read_label(struct iio_dev *indio_dev,
770 struct iio_chan_spec const *chan, char *label)
771 {
772 return snprintf(label, PAGE_SIZE, "%s\n",
773 rradc_chans[chan->address].label);
774 }
775
776 static const struct iio_info rradc_info = {
777 .read_raw = rradc_read_raw,
778 .read_label = rradc_read_label,
779 };
780
781 static const struct rradc_channel rradc_chans[RR_ADC_CHAN_MAX] = {
782 {
783 .label = "batt_id",
784 .scale_fn = rradc_post_process_batt_id,
785 .lsb = RR_ADC_BATT_ID_5_LSB,
786 .status = RR_ADC_BATT_ID_STS,
787 .size = 6,
788 .trigger_addr = RR_ADC_BATT_ID_TRIGGER,
789 .trigger_mask = BIT(0),
790 }, {
791 .label = "batt",
792 .lsb = RR_ADC_BATT_THERM_LSB,
793 .status = RR_ADC_BATT_THERM_STS,
794 .size = 2,
795 .trigger_addr = RR_ADC_BATT_THERM_TRIGGER,
796 }, {
797 .label = "pmi8998_skin",
798 .lsb = RR_ADC_SKIN_TEMP_LSB,
799 .status = RR_ADC_AUX_THERM_STS,
800 .size = 2,
801 .trigger_addr = RR_ADC_AUX_THERM_TRIGGER,
802 }, {
803 .label = "usbin_i",
804 .lsb = RR_ADC_USB_IN_I_LSB,
805 .status = RR_ADC_USB_IN_I_STS,
806 .size = 2,
807 .trigger_addr = RR_ADC_USB_IN_I_TRIGGER,
808 }, {
809 .label = "usbin_v",
810 .lsb = RR_ADC_USB_IN_V_LSB,
811 .status = RR_ADC_USB_IN_V_STS,
812 .size = 2,
813 .trigger_addr = RR_ADC_USB_IN_V_TRIGGER,
814 .trigger_mask = BIT(7),
815 }, {
816 .label = "dcin_i",
817 .lsb = RR_ADC_DC_IN_I_LSB,
818 .status = RR_ADC_DC_IN_I_STS,
819 .size = 2,
820 .trigger_addr = RR_ADC_DC_IN_I_TRIGGER,
821 }, {
822 .label = "dcin_v",
823 .lsb = RR_ADC_DC_IN_V_LSB,
824 .status = RR_ADC_DC_IN_V_STS,
825 .size = 2,
826 .trigger_addr = RR_ADC_DC_IN_V_TRIGGER,
827 }, {
828 .label = "pmi8998_die",
829 .lsb = RR_ADC_PMI_DIE_TEMP_LSB,
830 .status = RR_ADC_PMI_DIE_TEMP_STS,
831 .size = 2,
832 .trigger_addr = RR_ADC_PMI_DIE_TEMP_TRIGGER,
833 .trigger_mask = RR_ADC_TRIGGER_EVERY_CYCLE,
834 }, {
835 .label = "chg",
836 .lsb = RR_ADC_CHARGER_TEMP_LSB,
837 .status = RR_ADC_CHARGER_TEMP_STS,
838 .size = 2,
839 .trigger_addr = RR_ADC_CHARGER_TEMP_TRIGGER,
840 }, {
841 .label = "gpio",
842 .lsb = RR_ADC_GPIO_LSB,
843 .status = RR_ADC_GPIO_STS,
844 .size = 2,
845 .trigger_addr = RR_ADC_GPIO_TRIGGER,
846 },
847 };
848
849 static const struct iio_chan_spec rradc_iio_chans[RR_ADC_CHAN_MAX] = {
850 {
851 .type = IIO_RESISTANCE,
852 .info_mask_separate = BIT(IIO_CHAN_INFO_RAW),
853 .address = RR_ADC_BATT_ID,
854 .channel = 0,
855 .indexed = 1,
856 }, {
857 .type = IIO_TEMP,
858 .info_mask_separate = BIT(IIO_CHAN_INFO_RAW),
859 .address = RR_ADC_BATT_THERM,
860 .channel = 0,
861 .indexed = 1,
862 }, {
863 .type = IIO_TEMP,
864 .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
865 BIT(IIO_CHAN_INFO_SCALE) |
866 BIT(IIO_CHAN_INFO_OFFSET),
867 .address = RR_ADC_SKIN_TEMP,
868 .channel = 1,
869 .indexed = 1,
870 }, {
871 .type = IIO_CURRENT,
872 .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
873 BIT(IIO_CHAN_INFO_SCALE),
874 .address = RR_ADC_USBIN_I,
875 .channel = 0,
876 .indexed = 1,
877 }, {
878 .type = IIO_VOLTAGE,
879 .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
880 BIT(IIO_CHAN_INFO_SCALE),
881 .address = RR_ADC_USBIN_V,
882 .channel = 0,
883 .indexed = 1,
884 }, {
885 .type = IIO_CURRENT,
886 .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
887 BIT(IIO_CHAN_INFO_SCALE),
888 .address = RR_ADC_DCIN_I,
889 .channel = 1,
890 .indexed = 1,
891 }, {
892 .type = IIO_VOLTAGE,
893 .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
894 BIT(IIO_CHAN_INFO_SCALE),
895 .address = RR_ADC_DCIN_V,
896 .channel = 1,
897 .indexed = 1,
898 }, {
899 .type = IIO_TEMP,
900 .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
901 BIT(IIO_CHAN_INFO_SCALE) |
902 BIT(IIO_CHAN_INFO_OFFSET),
903 .address = RR_ADC_DIE_TEMP,
904 .channel = 2,
905 .indexed = 1,
906 }, {
907 .type = IIO_TEMP,
908 .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
909 BIT(IIO_CHAN_INFO_OFFSET) |
910 BIT(IIO_CHAN_INFO_SCALE),
911 .address = RR_ADC_CHG_TEMP,
912 .channel = 3,
913 .indexed = 1,
914 }, {
915 .type = IIO_VOLTAGE,
916 .info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED) |
917 BIT(IIO_CHAN_INFO_SCALE),
918 .address = RR_ADC_GPIO,
919 .channel = 2,
920 .indexed = 1,
921 },
922 };
923
rradc_probe(struct platform_device * pdev)924 static int rradc_probe(struct platform_device *pdev)
925 {
926 struct device *dev = &pdev->dev;
927 struct iio_dev *indio_dev;
928 struct rradc_chip *chip;
929 int ret, i, batt_id_delay;
930
931 indio_dev = devm_iio_device_alloc(dev, sizeof(*chip));
932 if (!indio_dev)
933 return -ENOMEM;
934
935 chip = iio_priv(indio_dev);
936 chip->regmap = dev_get_regmap(pdev->dev.parent, NULL);
937 if (!chip->regmap) {
938 dev_err(dev, "Couldn't get parent's regmap\n");
939 return -EINVAL;
940 }
941
942 chip->dev = dev;
943 mutex_init(&chip->conversion_lock);
944
945 ret = device_property_read_u32(dev, "reg", &chip->base);
946 if (ret < 0) {
947 dev_err(chip->dev, "Couldn't find reg address, ret = %d\n",
948 ret);
949 return ret;
950 }
951
952 batt_id_delay = -1;
953 ret = device_property_read_u32(dev, "qcom,batt-id-delay-ms",
954 &batt_id_delay);
955 if (!ret) {
956 for (i = 0; i < RRADC_BATT_ID_DELAY_MAX; i++) {
957 if (batt_id_delay == batt_id_delays[i])
958 break;
959 }
960 if (i == RRADC_BATT_ID_DELAY_MAX)
961 batt_id_delay = -1;
962 }
963
964 if (batt_id_delay >= 0) {
965 batt_id_delay = FIELD_PREP(BATT_ID_SETTLE_MASK, batt_id_delay);
966 ret = regmap_set_bits(chip->regmap,
967 chip->base + RR_ADC_BATT_ID_CFG,
968 batt_id_delay);
969 if (ret < 0) {
970 dev_err(chip->dev,
971 "BATT_ID settling time config failed:%d\n",
972 ret);
973 }
974 }
975
976 /* Get the PMIC revision, we need it to handle some varying coefficients */
977 chip->pmic = qcom_pmic_get(chip->dev);
978 if (IS_ERR(chip->pmic)) {
979 dev_err(chip->dev, "Unable to get reference to PMIC device\n");
980 return PTR_ERR(chip->pmic);
981 }
982
983 switch (chip->pmic->subtype) {
984 case PMI8998_SUBTYPE:
985 indio_dev->name = "pmi8998-rradc";
986 break;
987 case PM660_SUBTYPE:
988 indio_dev->name = "pm660-rradc";
989 break;
990 default:
991 indio_dev->name = DRIVER_NAME;
992 break;
993 }
994 indio_dev->modes = INDIO_DIRECT_MODE;
995 indio_dev->info = &rradc_info;
996 indio_dev->channels = rradc_iio_chans;
997 indio_dev->num_channels = ARRAY_SIZE(rradc_iio_chans);
998
999 return devm_iio_device_register(dev, indio_dev);
1000 }
1001
1002 static const struct of_device_id rradc_match_table[] = {
1003 { .compatible = "qcom,pm660-rradc" },
1004 { .compatible = "qcom,pmi8998-rradc" },
1005 { }
1006 };
1007 MODULE_DEVICE_TABLE(of, rradc_match_table);
1008
1009 static struct platform_driver rradc_driver = {
1010 .driver = {
1011 .name = DRIVER_NAME,
1012 .of_match_table = rradc_match_table,
1013 },
1014 .probe = rradc_probe,
1015 };
1016 module_platform_driver(rradc_driver);
1017
1018 MODULE_DESCRIPTION("QCOM SPMI PMIC RR ADC driver");
1019 MODULE_AUTHOR("Caleb Connolly <caleb.connolly@linaro.org>");
1020 MODULE_LICENSE("GPL");
1021