Lines Matching +full:in +full:- +full:built
1 # SPDX-License-Identifier: GPL-2.0-only
50 this symbol, but new drivers should use the generic gpio-regmap
60 non-sleeping contexts. They can make bitbanged serial protocols
81 numberspace-based functionalities of the sysfs interface.
125 # put drivers in the right section, in alphabetical order
137 Enables support for the idio-16 library functions. The idio-16 library
139 ACCES IDIO-16 family such as the 104-IDIO-16 and the PCI-IDIO-16.
141 If built as a module its name will be gpio-idio-16.
147 tristate "GPIO driver for 74xx-ICs with MMIO access"
151 Say yes here to support GPIO functionality for 74xx-compatible ICs
166 If driver is built as a module it will be called gpio-altera.
327 and write pin state) for GPIO implemented in a number of GE single
337 Support for common GPIOs from the Faraday FTGPIO010 IP core, found in
341 tristate "Generic memory-mapped GPIO controller support (MMIO platform device)"
344 Say yes here to support basic platform_device memory-mapped GPIO controllers.
347 tristate "Intel Granite Rapids-D vGPIO support"
354 - Intel Granite Rapids-D
362 be called gpio-graniterapids.
381 This GPIO controller supports double-edge interrupt and multi-core
399 ICH-based chipsets. Currently supported devices: ICH6, ICH7, ICH8
429 bool "Loongson-2/3 GPIO support"
432 Driver for GPIO functionality on Loongson-2F/3A/3B processors.
443 up to 60 GPIOS in total, 4 of which are dedicated GPIO pins, and
467 Say yes here to support the GPIO controller in Fujitsu MB86S70 SoCs.
483 created by attaching a 16-bit latch to the bus.
553 Say yes here to support the on-chip GPIO lines on the OCTEON
587 tristate "Renesas R-Car and RZ/G GPIO support"
591 Say yes here to support GPIO on Renesas R-Car or RZ/G SoCs.
611 are grouped in four 8-bit wide ports.
613 When built as a module, the module will be called realtek_otto_gpio.
618 A 32-bit single register GPIO fixed in/out implementation. This
654 maintain their value during backup/self-refresh.
672 via a SIOX bus and have a number of fixed-direction I/O lines.
680 This is a single-register MMIO GPIO driver for complex cases
681 where only several fields in register belong to GPIO lines and
731 - Elkhart Lake
732 - Merrifield
734 If built as a module its name will be gpio-tangier.
764 tristate "TS-4800 DIO blocks and compatibles"
769 This driver support TS-4800 FPGA GPIO controllers.
772 tristate "Cavium ThunderX/OCTEON-TX GPIO"
779 Say yes here to support the on-chip GPIO lines on the ThunderX
780 and OCTEON-TX families of SoCs.
817 bool "APM X-Gene GPIO controller support"
820 This driver is to support the GPIO block within the APM X-Gene SoC
826 tristate "APM X-Gene GPIO standby controller support"
832 This driver supports the GPIO block within the APM X-Gene
864 Say yes here to support the GPIO controller in LSI ZEVIO SoCs.
874 tristate "ZynqMP ps-mode pin GPIO configuration driver"
878 Say yes here to support the ZynqMP ps-mode pin GPIO configuration
881 This ps-mode pin GPIO driver is based on GPIO framework. PS_MODE
882 is 4-bits boot mode pins. It sets and gets the status of
883 the ps-mode pin. Every pin can be configured as input/output.
893 tristate "GPIO support for AMD Fusion Controller Hub (G-series SOCs)"
896 as found on G-series SOCs (e.g. GX-412TC).
899 needs to be provided with platform-specific configuration.
910 ARMv7-based SoCs.
919 IDT 79RC3243X-based devices like Mikrotik RB532.
922 be called gpio-idt3243x.
926 menu "Port-mapped I/O GPIO drivers"
938 Additional drivers must be enabled in order to use the
949 in the early 1970s but compatible interfaces are nowadays typically
950 found embedded in larger VLSI processing chips and FPGA components.
952 If built as a module its name will be gpio-i8255.
955 tristate "ACCES 104-DIO-48E GPIO support"
964 Enables GPIO support for the ACCES 104-DIO-48E series (104-DIO-48E,
965 104-DIO-24E). The base port addresses for the devices may be
970 tristate "ACCES 104-IDIO-16 GPIO support"
976 Enables GPIO support for the ACCES 104-IDIO-16 family (104-IDIO-16,
977 104-IDIO-16E, 104-IDO-16, 104-IDIO-8, 104-IDIO-8E, 104-IDO-8). The
983 tristate "ACCES 104-IDI-48 GPIO support"
991 Enables GPIO support for the ACCES 104-IDI-48 family (104-IDI-48A,
992 104-IDI-48AC, 104-IDI-48B, 104-IDI-48BC). The base port addresses for
998 tristate "Fintek and Nuvoton Super-I/O GPIO support"
1000 This option enables support for GPIOs found on Fintek Super-I/O
1002 As well as Nuvoton Super-I/O chip NCT6126D.
1005 be called f7188x-gpio.
1008 tristate "Diamond Systems GPIO-MM GPIO support"
1014 Enables GPIO support for the Diamond Systems GPIO-MM and GPIO-MM-12.
1016 The Diamond Systems GPIO-MM device features 48 lines of digital I/O
1049 active during S3. The suspend-powered GPIOs can be used to wake the
1050 system from the Suspend-to-RAM state.
1056 Twenty-one are powered by the core power rail and 9 from the
1069 be called gpio-sch311x.
1072 tristate "TS-5500 DIO blocks and compatibles"
1077 blocks of the TS-5500: DIO1, DIO2 and the LCD port, and the TS-5600
1090 boot-time parameter "gpio_winbond.gpios" with a bitmask of GPIO
1094 be called gpio-winbond.
1115 tristate "Avionic Design N-bit GPIO expander"
1134 be called gpio-fxl6408.
1141 GPIO driver for ADI DS4520 I2C-based GPIO expander.
1145 be called gpio-ds4520.
1152 Expander. This is used at least on the Cambria GW2358-4.
1158 GPIO driver for Maxim MAX7300 I2C-based GPIO expander.
1161 tristate "MAX7319, MAX7320-7327 I2C Port Expanders"
1163 Say yes here to support the MAX7319, MAX7320-7327 series of I2C
1165 Input (designated by 'I'), Push-Pull Output ('O'), or Open-Drain
1184 controller. It requires the driver to be built in the kernel.
1190 Say yes here to provide access to several register-oriented
1219 tristate "PCA9570 4-Bit I2C GPO expander"
1224 be called gpio-pca9570.
1231 Say yes here to provide access to most "quasi-bidirectional" I2C
1243 Your board setup code will need to declare the expanders in
1248 This driver provides an in-kernel interface to those GPIOs using
1249 platform-neutral GPIO calls.
1252 tristate "TPIC2810 8-Bit I2C GPO expander"
1257 be called gpio-tpic2810.
1265 Series supported include TS-4100, TS-4900, TS-7970 and TS-7990.
1275 This option enables support for on-chip GPIO found
1283 This option enables support for the GPIO function found in the Analog
1307 This driver can also be built as a module. If so, the module
1308 will be called gpio-bd71815.
1315 available on the ROHM PMIC in total. The GPIOs are limited to
1319 This driver can also be built as a module. If so, the module
1320 will be called gpio-bd71828.
1327 available on the ROHM PMIC in total, both of which can also
1330 This driver can also be built as a module. If so, the module
1331 will be called gpio-bd9571mwv.
1340 This driver can also be built as a module. If so, the module will be
1341 called gpio-cgbc.
1350 This driver can also be built as a module. If so, the module
1351 will be called gpio-cros-ec.
1360 Say Yes if you have a Intel SoC-based tablet with Crystal Cove PMIC
1363 This driver can also be built as a module. If so, the module will be
1364 called gpio-crystalcove.
1392 If driver is built as a module it will be called gpio-da9055.
1403 This driver can also be built as a module. If so, the module
1404 will be called gpio-dln2.
1423 be called gpio-elkhartlake.
1426 tristate "Janz VMOD-TTL Digital IO Module"
1429 This enables support for the Janz VMOD-TTL Digital IO module.
1430 This driver provides support for driving the pins in output
1440 This driver can also be built as a module. If so, the module will be
1441 called gpio-kempld.
1452 This driver can also be built as a module. If so, the module
1453 will be called gpio-ljca.
1470 This driver can also be built as a module. If so, the module will be
1471 called gpio-lp873x.
1480 This driver can also be built as a module. If so, the module will be
1481 called gpio-lp87565.
1490 This driver can also be built as a module. If so, the module will be
1491 called gpio-macsmc.
1508 This driver can also be built as a module. If so, the module will be
1509 called gpio-max7360.
1535 There are two GPIOs available on these chips in total, both of
1538 This driver can also be built as a module. If so, the module will be
1539 called gpio-max77759.
1550 This driver can also be built as a module. If so, the module will be
1551 called gpio-nct6694.
1586 This driver can also be built as a module. If so, the module will be
1587 called gpio-sl28cpld.
1612 Add support for the GPIO IP in the timberdale FPGA.
1620 Networks TN48M switch Lattice CPLD. It provides 12 pins in total,
1621 they are input-only or output-only type.
1623 This driver can also be built as a module. If so, the
1624 module will be called gpio-tn48m.
1652 This driver can also be built as a module. If so, the module will be
1681 There are 7 GPIOs and few sensor-related GPIOs supported
1687 tristate "TQ-Systems TQMx86 GPIO"
1698 Say yes here to access the GPIO signals of various multi-function
1715 Say Yes if you have an Intel SoC-based tablet with Whiskey Cove PMIC
1718 This driver can also be built as a module. If so, the module will be
1719 called gpio-wcove.
1767 This chip can be found on Miro, Hauppauge and STB TV-cards.
1772 Documentation/driver-api/gpio/bt8xxgpio.rst
1807 This controller should be used in parallel with pinctrl-mlxbf3 to
1809 This driver can also be built as a module called mlxbf3-gpio.
1818 Hub) which is for IVI (In-Vehicle Infotainment) use.
1838 tristate "ACCES PCI-IDIO-16 GPIO support"
1842 Enables GPIO support for the ACCES PCI-IDIO-16. An interrupt is
1848 tristate "ACCES PCIe-IDIO-24 GPIO support"
1854 Enables GPIO support for the ACCES PCIe-IDIO-24 family (PCIe-IDIO-24,
1855 PCIe-IDI-24, PCIe-IDO-24, PCIe-IDIO-12). An interrupt is generated
1861 tristate "RDC R-321x GPIO support"
1882 tristate "74x164 serial-in/parallel-out 8-bits shift register"
1884 Driver for 74x164 compatible serial-in/parallel-out 8-outputs
1893 MAX31953 and MAX31963 industrial serializer, a daisy-chainable
1902 GPIO driver for Maxim MAX7301 SPI-based GPIO expander.
1905 tristate "Freescale MC33880 high-side/low-side switch"
1907 SPI driver for Freescale MC33880 high-side/low-side switch.
1911 tristate "Generic parallel-in/serial-out shift register"
1913 GPIO driver for SPI compatible parallel-in/serial-out shift
1917 tristate "EXAR XRA1403 16-bit GPIO expander"
1920 GPIO driver for EXAR XRA1403 16-bit SPI-based GPIO expander.
1962 This driver can also be built as a module. If so, the module
1977 - Assign permissions for a collection of GPIO lines to a user,
1978 - Export a collection of GPIO lines to a virtual machine,
1979 - Provide a generic driver for a GPIO-operated device in an
1993 This module is DEPRECATED. Please consider using gpio-sim instead.
1997 User could use it through the script in
1998 tools/testing/selftests/gpio/gpio-mockup.sh. Reference the usage in
2006 Say Y here to enable guest support for virtio-based GPIO controllers.
2017 This enables the GPIO simulator - a configfs-based GPIO testing
2029 GPIOs. Use the 'tools/gpio/gpio-sloppy-logic-analyzer' script with
2032 analyzer which can be affected by latencies, non-deterministic code
2036 If this driver is built as a module it will be called
2037 'gpio-sloppy-logic-analyzer'.
2046 Say Y here to enable the configurable, configfs-based virtual GPIO
2049 This driver is aimed as a helper in spotting any regressions in
2050 hot-unplug handling in GPIOLIB.