Lines Matching +full:r9a07g044 +full:- +full:mtu3
1 // SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
9 /dts-v1/;
11 #include <dt-bindings/gpio/gpio.h>
12 #include <dt-bindings/pinctrl/rzg2l-pinctrl.h>
17 model = "MYIR Tech Limited Remi Pi MYB-YG2LX-REMI";
18 compatible = "myir,remi-pi", "renesas,r9a07g044l2", "renesas,r9a07g044";
36 stdout-path = "serial0:115200n8";
39 hdmi-out {
40 compatible = "hdmi-connector";
42 ddc-i2c-bus = <&i2c1>;
46 remote-endpoint = <<8912_out>;
57 reg_1p8v: regulator-1p8v {
58 compatible = "regulator-fixed";
59 regulator-name = "fixed-1.8V";
60 vin-supply = <®_5p0v>;
61 regulator-min-microvolt = <1800000>;
62 regulator-max-microvolt = <1800000>;
63 regulator-always-on;
66 reg_3p3v: regulator-3p3v {
67 compatible = "regulator-fixed";
68 regulator-name = "fixed-3.3V";
69 vin-supply = <®_5p0v>;
70 regulator-min-microvolt = <3300000>;
71 regulator-max-microvolt = <3300000>;
72 regulator-always-on;
75 reg_5p0v: regulator-5p0v {
76 compatible = "regulator-fixed";
77 regulator-name = "fixed-5.0V";
78 regulator-min-microvolt = <5000000>;
79 regulator-max-microvolt = <5000000>;
82 reg_1p1v: regulator-vdd-core {
83 compatible = "regulator-fixed";
84 regulator-name = "fixed-1.1V";
85 regulator-min-microvolt = <1100000>;
86 regulator-max-microvolt = <1100000>;
87 regulator-always-on;
97 remote-endpoint = <<8912_in>;
98 data-lanes = <1 2 3 4>;
113 pinctrl-0 = <ð0_pins>;
114 pinctrl-names = "default";
115 phy-handle = <&phy0>;
116 phy-mode = "rgmii-id";
119 phy0: ethernet-phy@4 {
120 compatible = "ethernet-phy-ieee802.3-c22";
122 interrupts-extended = <&pinctrl RZG2L_GPIO(44, 2) IRQ_TYPE_LEVEL_LOW>;
123 reset-gpios = <&pinctrl RZG2L_GPIO(44, 3) GPIO_ACTIVE_LOW>;
128 pinctrl-0 = <ð1_pins>;
129 pinctrl-names = "default";
130 phy-handle = <&phy1>;
131 phy-mode = "rgmii-id";
134 phy1: ethernet-phy@6 {
135 compatible = "ethernet-phy-ieee802.3-c22";
137 interrupts-extended = <&pinctrl RZG2L_GPIO(43, 2) IRQ_TYPE_LEVEL_LOW>;
138 reset-gpios = <&pinctrl RZG2L_GPIO(43, 3) GPIO_ACTIVE_LOW>;
143 clock-frequency = <24000000>;
147 mali-supply = <®_1p1v>;
151 pinctrl-0 = <&i2c0_pins>;
152 pinctrl-names = "default";
154 clock-frequency = <400000>;
157 hdmi-bridge@48 {
160 reset-gpios = <&pinctrl RZG2L_GPIO(42, 2) GPIO_ACTIVE_LOW>;
163 #address-cells = <1>;
164 #size-cells = <0>;
170 data-lanes = <1 2 3 4>;
171 remote-endpoint = <&dsi_out>;
179 remote-endpoint = <&hdmi_con>;
187 pinctrl-0 = <&i2c1_pins>;
188 pinctrl-names = "default";
189 clock-frequency = <100000>;
194 pinctrl-0 = <&i2c2_pins>;
195 pinctrl-names = "default";
196 clock-frequency = <100000>;
201 pinctrl-0 = <&i2c3_pins>;
202 pinctrl-names = "default";
203 clock-frequency = <100000>;
207 &mtu3 {
264 input-enable;
269 input-enable;
293 sd0-ctrl {
295 power-source = <1800>;
298 sd0-data {
301 power-source = <1800>;
304 sd0-rst {
306 power-source = <1800>;
312 pinctrl-0 = <&scif0_pins>;
313 pinctrl-names = "default";
318 pinctrl-0 = <&scif4_pins>;
319 pinctrl-names = "default";
324 pinctrl-0 = <&sdhi0_pins>;
325 pinctrl-1 = <&sdhi0_pins>;
326 pinctrl-names = "default", "state_uhs";
328 vmmc-supply = <®_3p3v>;
329 vqmmc-supply = <®_1p8v>;
330 bus-width = <8>;
331 mmc-hs200-1_8v;
332 non-removable;
333 fixed-emmc-driver-type = <1>;