Lines Matching +full:system +full:- +full:on +full:- +full:a +full:- +full:chip
3 The chip name.
4 This should be a short, lowercase string, not containing
6 This attribute represents the chip name. It is the only
14 A descriptive label that allows to uniquely identify a
15 device within the system.
16 The contents of the label are free-form.
22 The interval at which the chip will update readings.
27 Some devices have a variable update rate or interval.
46 If voltage drops to or below this limit, the system may
48 least, it should report a fault.
66 If voltage reaches or exceeds this limit, the system may
68 least, it should report a fault.
78 Voltage measured on the chip pin.
80 Actual voltage depends on the scaling resistors on the
81 motherboard, as recommended in the chip datasheet.
83 This varies by chip and by motherboard.
85 by the chip driver, and must be done by the application.
87 do scale, because of internal resistors built into a chip.
90 "pins" of the chip.
135 this voltage channel is being used for, and user-space
137 user-space.
145 When disabled the sensor read will return -ENODATA.
147 - 1: Enable
148 - 0: Disable
154 Reports a voltage hard failure (eg: shorted component)
156 - 1: Failed
157 - 0: Ok
178 an arbitrary number, as not all standards have a version
245 This value is a characteristic of the fan connected to the
249 Should only be created if the chip has a register to configure
250 the number of pulses. In the absence of such a register (and
262 Only makes sense if the chip supports closed-loop fan speed
263 control based on the measured fan speed.
272 this fan channel is being used for, and user-space doesn't.
273 In all other cases, the label is provided by user-space.
281 When disabled the sensor read will return -ENODATA.
283 - 1: Enable
284 - 0: Disable
290 Reports if a fan has reported failure.
292 - 1: Failed
293 - 0: Ok
311 - 0: no fan speed control (i.e. fan at full speed)
312 - 1: manual fan speed control enabled (using `pwmY`)
313 - 2+: automatic fan speed control enabled
315 Check individual chip documentation files for automatic mode
322 - 0: DC mode (direct current)
323 - 1: PWM mode (pulse-width modulation)
342 Which values are possible depend on the chip used.
352 Number of trip points is chip-dependent. Use this for chips
363 Number of trip points is chip-dependent. Use this for chips
376 - 1: CPU embedded diode
377 - 2: 3904 transistor
378 - 3: thermal diode
379 - 4: thermistor
380 - 5: AMD AMDSI
381 - 6: Intel PECI
397 - 0: OK
398 - 1: temperature has reached tempY_max
414 - 0: OK
415 - 1: temperature has reached tempY_min
425 Must be reported as an absolute temperature, NOT a delta
435 Must be reported as an absolute temperature, NOT a delta
461 - 0: OK
462 - 1: temperature has reached tempY_crit
472 Must be reported as an absolute temperature, NOT a delta
491 - 0: OK
492 - 1: temperature has reached tempY_emergency
502 Must be reported as an absolute temperature, NOT a delta
522 Must be reported as an absolute temperature, NOT a delta
530 by the chip.
543 this temperature channel is being used for, and user-space
545 user-space.
581 When disabled the sensor read will return -ENODATA.
583 - 1: Enable
584 - 0: Disable
682 When disabled the sensor read will return -ENODATA.
684 - 1: Enable
685 - 0: Disable
715 Power use averaging interval. A poll
757 A poll notification is sent to
767 A poll notification is sent to
817 system should take action to reduce power use.
818 A poll notification is sent to this file if the
865 system is expected take drastic action to reduce
866 power consumption, such as a system shutdown or
867 a forced powerdown of some devices.
878 -ENODATA.
880 - 1: Enable
881 - 0: Disable
914 -ENODATA.
916 - 1: Enable
917 - 0: Disable
925 - 0: OK
926 - 1: Humidity limit has been reached
935 -ENODATA.
937 - 1: Enable
938 - 0: Disable
944 Reports a humidity sensor failure.
946 - 1: Failed
947 - 0: Ok
955 Unit: milli-percent (per cent mille, pcm)
966 this humidity channel is being used for, and user-space
968 user-space.
976 Unit: milli-percent (per cent mille, pcm)
984 - 0: OK
985 - 1: Maximum humidity detected
993 Unit: milli-percent (per cent mille, pcm)
995 Must be reported as an absolute humidity, NOT a delta
1004 Unit: milli-percent (per cent mille, pcm)
1012 - 0: OK
1013 - 1: Minimum humidity detected
1021 Unit: milli-percent (per cent mille, pcm)
1023 Must be reported as an absolute humidity, NOT a delta
1032 Unit: milli-percent (per cent mille, pcm)
1040 Unit: milli-percent (per cent mille, pcm)
1049 - 0: OK
1050 - 1: intrusion detected
1063 - 0: disable
1064 - 1: enable
1070 PEC support on I2C devices
1072 - 0, off, n: disable
1073 - 1, on, y: enable