regulator: Add TPS65185

Merge series from Andreas Kemnade <andreas@kemnade.info>:

Add a driver for the TPS65185 regulator which provides the
comparatively high voltages needed for electronic paper

regulator: Add TPS65185

Merge series from Andreas Kemnade <andreas@kemnade.info>:

Add a driver for the TPS65185 regulator which provides the
comparatively high voltages needed for electronic paper displays.

Datasheet for the TPS65185 is at https://www.ti.com/lit/gpn/tps65185

To simplify things, include the hwmon part directly which is only
one temperature sensor and there are no other functions besides regulators
in this chip.

show more ...

regulator: Add TPS65185 driver

Add a driver for the TPS65185 regulator. Implement handling of the various
gpio pins. Because the PWRUP (=enable) pin functionality can be achieved
by just using two b

regulator: Add TPS65185 driver

Add a driver for the TPS65185 regulator. Implement handling of the various
gpio pins. Because the PWRUP (=enable) pin functionality can be achieved
by just using two bits instead, just ensure that it is set to a stable
value.
Implement the pair of symmetric LDOs as a single regulator because they
share a single voltage set register. As the VCOM regulator sits behind that
machinery, just define that one as a supply.
For simplicity, just add the temperature sensor (depending on external NTC)
directly.

There is a mechanism to measure some kick-back voltage during a defined EPD
operation, to calibrate the VCOM voltage setting and store that
non-volatile in the chip to be the power up default setup. That is not
implemented yet in the driver, but that also means that there is a
non-factory default value in these registers after power-up.

Tested-by: Josua Mayer <josua.mayer@jm0.eu>
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Link: https://patch.msgid.link/20260102-tps65185-submit-v3-2-23bda35772f2@kemnade.info
Signed-off-by: Mark Brown <broonie@kernel.org>

show more ...

Add Richtek RT8092 support

Merge series from cy_huang@richtek.com:

This patch series add rt8092 regulator support.

regulator: Add rt8092 support

RT8092 is a 3MHz 4A efficiency step-down converter with I2C control
interface. It can support wide output range from 0.7 to 5.5V, based on
the voltage bank selection.

regulator: Add rt8092 support

RT8092 is a 3MHz 4A efficiency step-down converter with I2C control
interface. It can support wide output range from 0.7 to 5.5V, based on
the voltage bank selection.

Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Link: https://patch.msgid.link/d2293c513f396f86e54f9b806fd0195b57db7aae.1766125676.git.cy_huang@richtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>

show more ...

regulator: max77675: Add MAX77675 regulator driver

Add support for the Maxim Integrated MAX77675 PMIC regulator.

The MAX77675 is a compact, highly efficient SIMO (Single Inductor Multiple Output)
p

regulator: max77675: Add MAX77675 regulator driver

Add support for the Maxim Integrated MAX77675 PMIC regulator.

The MAX77675 is a compact, highly efficient SIMO (Single Inductor Multiple Output)
power management IC that provides four programmable buck-boost switching regulators
with only one inductor. It supports up to 700mA total output current and operates
from a single-cell Li-ion battery.

An integrated power-up sequencer and I2C interface allow flexible startup
configuration and runtime control.

Signed-off-by: Joan Na <joan.na@analog.com>
Link: https://patch.msgid.link/20251207032907.4850-3-joan.na@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>

show more ...

regulator: Use container_of_const() when all types are

Merge series from Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>:

Use container_of_const(), which is preferred over container_of()

regulator: Use container_of_const() when all types are

Merge series from Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>:

Use container_of_const(), which is preferred over container_of(), when
the argument 'ptr' and returned pointer are already const, for better
code safety and readability.

Some drivers already have const everywhere, so container_of_const can be
directly used. In few other drivers, the final pointer can be constified
that way.

show more ...

regulator: Add FP9931/JD9930

Merge series from Andreas Kemnade <andreas@kemnade.info>:

Add a driver for the FP9931/JD9930 regulator which provides the
comparatively high voltages needed for electro

regulator: Add FP9931/JD9930

Merge series from Andreas Kemnade <andreas@kemnade.info>:

Add a driver for the FP9931/JD9930 regulator which provides the
comparatively high voltages needed for electronic paper displays.

Datasheet for the FP9931 is at
https://www.fitipower.com/dl/file/flXa6hIchVeu0W3K

Although it is in English, it seems to be only downloadable
from the Chinese part of that website.
For the JD9930 there can be a datasheet found at
https://e2e.ti.com/cfs-file/__key/communityserver-discussions-components-files/196/JD9930_2D00_0.7_2D00_JUN_2D00_2019.pdf

To simplify things, include the hwmon part directly which is only
one register read and there are not other functions besides
regulators in this chip.

show more ...

regulator: Add FP9931/JD9930 driver

Add a driver for the FP9931/JD9930 regulator. Implement handling of the PG
(power good), TS_EN (temperature sensor enable), and EN (enable regulators)
pins. Imple

regulator: Add FP9931/JD9930 driver

Add a driver for the FP9931/JD9930 regulator. Implement handling of the PG
(power good), TS_EN (temperature sensor enable), and EN (enable regulators)
pins. Implement the pair of symmetric LDOs as a single regulator because
they share a single voltage set register. For simplicity, just add the
temperature sensor (depending on external NTC) directly.

Limitations:
- As these regulators are controlled together with the VCOM regulator via
the EN pin, some kind of management must be in place. As the enable op
is not called when the regulator is already enabled, simple refcounting
seems not to work to avoid clearing EN when one regulator is still
enabled. As these regulators are typically used together, this
limitation should not hurt hard, just provide the is_enabled op.
- As the VCOM step is quite odd (5V/255 steps), rounding is needed.
Due to some limitations in the regulator core, the max/min voltages in
the devicetree must match the idea of the driver how to round things
exactly.
- Night mode is not implemented, so only the FP9931 compatible is needed in
the driver, there is no REGULATOR_MODE_NIGHT and no clear definition in
the datasheet what it does, also the XON pin which seems to be an input
related to that night mode is not used.

Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Link: https://patch.msgid.link/20251115-fp9931-submit-v3-3-92f5d0772b68@kemnade.info
Signed-off-by: Mark Brown <broonie@kernel.org>

show more ...

regulator: Add support for MediaTek MT6363 SPMI PMIC Regulators

Add a driver for the regulators found on the MT6363 PMIC, fully
controlled by SPMI interface.
This PMIC regulates voltage with an inpu

regulator: Add support for MediaTek MT6363 SPMI PMIC Regulators

Add a driver for the regulators found on the MT6363 PMIC, fully
controlled by SPMI interface.
This PMIC regulates voltage with an input range of 2.6-5.0V, and
features 10 buck converters and 26 LDOs.

Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patch.msgid.link/20251027110527.21002-5-angelogioacchino.delregno@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>

show more ...

regulator: Add support for MediaTek MT6316 SPMI PMIC Regulators

Add a driver for the regulators found on all types of the MediaTek
MT6316 SPMI PMIC, fully controlled by SPMI interface and featuring

regulator: Add support for MediaTek MT6316 SPMI PMIC Regulators

Add a driver for the regulators found on all types of the MediaTek
MT6316 SPMI PMIC, fully controlled by SPMI interface and featuring
four step down DCDC (buck) converters.

In particular, this includes support for:
- MT6316(BP/VP): 2+2 Phase (Phase 1: buck1+2, Phase 2: buck3+4)
- MT6316(CP/HP/KP): 3+1 Phase (Phase 1: buck1+2+4, Phase 2: buck3)
- MT6316(DP/TP): 4+0 Phase (Single phase, buck1+2+3+4)

Please note that the set/clear registers for the enable bits are
not documented in the datasheet version that I used as reference,
but those are used in the downstream driver and I verified that
are actually working as expected.

Besides, it's also worth clearly mentioning that the MT6316 PMICs
voltage selector register uses a weird 9-bits Big Endian format,
for which a driver-private helper is provided.

Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patch.msgid.link/20251027110527.21002-3-angelogioacchino.delregno@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>

show more ...

regulator: pf1550: Add support for regulator

Add regulator support for the pf1550 PMIC.

Signed-off-by: Samuel Kayode <samuel.kayode@savoirfairelinux.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Re

regulator: pf1550: Add support for regulator

Add regulator support for the pf1550 PMIC.

Signed-off-by: Samuel Kayode <samuel.kayode@savoirfairelinux.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Link: https://patch.msgid.link/20251001-pf1550-v12-3-a3302aa41687@savoirfairelinux.com
Signed-off-by: Lee Jones <lee@kernel.org>

show more ...

Merge tag 'mfd-next-6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd

Pull MFD updates from Lee Jones:
"This round of updates contains a fair amount of new device support, a
couple o

Merge tag 'mfd-next-6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd

Pull MFD updates from Lee Jones:
"This round of updates contains a fair amount of new device support, a
couple of fixes and some refactoring. The most notable additions
include new drivers for Loongson's Security Engine, RNG and TPM, new
drivers for TI's TPS6594 Power Button and BQ257xx Charger ICs.

The rest of the set provides a return value check fix and a
refactoring to use a more modern GPIO API for the VEXPRESS sysreg
driver, the removal of a deprecated IRQ ACK function from the MC13xxx
RTC driver and a new DT binding for the aforementioned TI BQ257xx
charger.

New Support & Features:
- Add a suite of drivers for the Loongson Security Engine, including
the core controller, a Random Number Generator (RNG) and Trusted
Platform Module (TPM) support.
- Introduce support for the TI TPS6594 PMIC's power button, including
the input driver, MFD cell registration, and a system power-off
handler.
- Add comprehensive support for the TI BQ257xx series of charger ICs,
including the core MFD driver and a power supply driver for the
charger functionality.

Improvements & Fixes:
- Check the return value of devm_gpiochip_add_data() in the VEXPRESS
sysreg driver to prevent potential silent failures.

Cleanups & Refactoring:
- Add a MAINTAINERS entry for the new Loongson Security Engine
drivers.
- Convert the VEXPRESS sysreg driver to use the modern generic GPIO
chip API.

Removals:
- Remove the deprecated and unused mc13xxx_irq_ack() function from
the MC13xxx RTC, input and touchscreen drivers.

Device Tree Bindings Updates:
- Add device tree bindings for the TI BQ25703A charger"

* tag 'mfd-next-6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (69 commits)
mfd: simple-mfd-i2c: Add compatible string for LX2160ARDB
mfd: simple-mfd-i2c: Keep compatible strings in alphabetical order
dt-bindings: mfd: twl: Add missing sub-nodes for TWL4030 & TWL603x
dt-bindings: watchdog: Add SMARC-sAM67 support
dt-bindings: mfd: tps6594: Allow gpio-line-names
mfd: intel-lpss: Add Intel Wildcat Lake LPSS PCI IDs
mfd: 88pm886: Add GPADC cell
mfd: vexpress-sysreg: Use more common syntax for compound literals
mfd: rz-mtu3: Fix MTU5 NFCR register offset
mfd: max77705: Setup the core driver as an interrupt controller
mfd: cs42l43: Remove IRQ masking in suspend
mfd: cs42l43: Move IRQ enable/disable to encompass force suspend
mfd: ls2kbmc: Add Loongson-2K BMC reset function support
mfd: ls2kbmc: Introduce Loongson-2K BMC core driver
mfd: bd71828, bd71815: Prepare for power-supply support
dt-bindings: mfd: aspeed: Add AST2700 SCU compatibles
dt-bindings: mfd: Convert aspeed,ast2400-p2a-ctrl to DT schema
dt-bindings: mfd: fsl,mc13xxx: Add buttons node
dt-bindings: mfd: fsl,mc13xxx: Convert txt to DT schema
mfd: macsmc: Add "apple,t8103-smc" compatible
...

show more ...

regulator: spacemit: support SpacemiT P1 regulators

Add support for the regulators found in the SpacemiT P1 PMIC. This
PMIC provides 6 buck converters and 12 LDO regulators.

The PMIC is implemente

regulator: spacemit: support SpacemiT P1 regulators

Add support for the regulators found in the SpacemiT P1 PMIC. This
PMIC provides 6 buck converters and 12 LDO regulators.

The PMIC is implemented as a multi-function device. These regulators
are probed based on this driver being named in a MFD cell in the simple
MFD I2C driver.

Signed-off-by: Alex Elder <elder@riscstar.com>
Link: https://patch.msgid.link/20250825172057.163883-4-elder@riscstar.com
Signed-off-by: Mark Brown <broonie@kernel.org>

show more ...

regulator: max77838: add max77838 regulator driver

Merge series from Ivaylo Ivanov <ivo.ivanov.ivanov1@gmail.com>:

This patchset adds support for the max77838 PMIC. It's used on the Galaxy
S7 lineu

regulator: max77838: add max77838 regulator driver

Merge series from Ivaylo Ivanov <ivo.ivanov.ivanov1@gmail.com>:

This patchset adds support for the max77838 PMIC. It's used on the Galaxy
S7 lineup of phones, and provides regulators for the display.

show more ...

regulator: max77838: add max77838 regulator driver

The max77838 PMIC contains a BUCK regulator and 4 LDOs. It's primarily
used in the Samsung Galaxy S7 lineup and is accessed over I2C.

Signed-off-b

regulator: max77838: add max77838 regulator driver

The max77838 PMIC contains a BUCK regulator and 4 LDOs. It's primarily
used in the Samsung Galaxy S7 lineup and is accessed over I2C.

Signed-off-by: Ivaylo Ivanov <ivo.ivanov.ivanov1@gmail.com>
Link: https://patch.msgid.link/20250914130230.2622030-3-ivo.ivanov.ivanov1@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>

show more ...

regulator: bq257xx: Add bq257xx boost regulator driver

Add support for the boost regulator found in the Texas Instruments
BQ25703. The boost regulator is capable of outputting between 4.48
and 20.8

regulator: bq257xx: Add bq257xx boost regulator driver

Add support for the boost regulator found in the Texas Instruments
BQ25703. The boost regulator is capable of outputting between 4.48
and 20.8 volts and between 0 and 6.35 amps.

Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20250904160530.66178-5-macroalpha82@gmail.com
Signed-off-by: Lee Jones <lee@kernel.org>

show more ...

regulator: pf530x: NXP PF530x regulator driver

Merge series from Woodrow Douglass <wdouglass@carnegierobotics.com>:

I wrote this driver to read settings and state from the nxp pf530x
regulator. Ple

regulator: pf530x: NXP PF530x regulator driver

Merge series from Woodrow Douglass <wdouglass@carnegierobotics.com>:

I wrote this driver to read settings and state from the nxp pf530x
regulator. Please consider it for inclusion, any criticism is welcome.

show more ...

regulator: pf530x: Add a driver for the NXP PF5300 Regulator

This driver allows reading some regulator settings and adjusting
output voltage. It is based on information from the datasheet
at https:/

regulator: pf530x: Add a driver for the NXP PF5300 Regulator

This driver allows reading some regulator settings and adjusting
output voltage. It is based on information from the datasheet
at https://www.nxp.com/docs/en/data-sheet/PF5300.pdf

Signed-off-by: Woodrow Douglass <wdouglass@carnegierobotics.com>
Message-ID: <20250902-pf530x-v7-2-10eb2542f944@carnegierobotics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

show more ...

regulator: rt5133: Add RT5133 PMIC regulator Support

RT5133 is a highly-integrated chip. It includes 8 LDOs and 3 GPOs that can
be used to drive output high/low purpose. The dependency of the GPO bl

regulator: rt5133: Add RT5133 PMIC regulator Support

RT5133 is a highly-integrated chip. It includes 8 LDOs and 3 GPOs that can
be used to drive output high/low purpose. The dependency of the GPO block is
internally LDO1 Voltage.

Signed-off-by: Jeff Chang <jeff_chang@richtek.com>
Link: https://patch.msgid.link/20250813020910.2977555-2-jeff_chang@richtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>

show more ...

regulator: add new PMIC PF0900 support

Merge series from Joy Zou <joy.zou@nxp.com>:

Add binding document and driver.

Signed-off-by: Joy Zou <joy.zou@nxp.com>
---
Changes in v3:

binding part
- cha

regulator: add new PMIC PF0900 support

Merge series from Joy Zou <joy.zou@nxp.com>:

Add binding document and driver.

Signed-off-by: Joy Zou <joy.zou@nxp.com>
---
Changes in v3:

binding part
- change regulator node names into lowercase.
- add more description for nxp,i2c-crc-enable.
- remove the unnecessary nxp,dvs-run/standby-voltage property.
These changes come from review comments:
https://lore.kernel.org/imx/e9f38e38-7df7-4d19-b5c0-2f18aeebcc78@kernel.org/
- add regulator-state-mem property for example.

driver part
- convert to use maple tree register cache.
- change of_match_ptr() name to lowercase since dt-binding changed.
- add more nxp,i2c-crc-enable description for commit message.
- remove the of_parse_cb and dvs from pf0900_regulators since the
unnecessary property nxp,dvs-run/standby-voltage removed.
- add set_suspend_enable/disable/voltage for the SW regulator_ops.
the run/standby voltage can be adjusted via the API which regulator
driver provides is recommended.
These changes come from binding review comments:
https://lore.kernel.org/imx/e9f38e38-7df7-4d19-b5c0-2f18aeebcc78@kernel.org/
- add bitfield.h header due to build issue.
- correct the sw4 id.
- add PF0900 prefix for short macro define in order to avoid duplication.
- merge the same mask define in order to simplify code.
- Link to v2: https://lore.kernel.org/r/20250721-b4-pf09-v2-v2-0-e2c568548032@nxp.com

Changes in v2:

binding part
- modify the binding file name to match compatible string.
- add one space for dt_binding_check warning.
- remove unnecessary quotes from "VAON".
- remove the unnecessary empty line.
- move unevaluatedProperties after the $ref.
- move additionalProperties after regulator type.
- remove unnecessary regulator description

driver part
- modify the copyright comment block to C++ style.
- add reg_read/write for regmap_bus.
- remove original pf0900_pmic_read/write.
- remove many regulator operations.
- use regmap_read replace pf0900_pmic_read.
- use regmap_update_bits and regmap_write_bits replace pf0900_pmic_write.
- move the code from pf0900.h to pf0900-regulator.c and delete the header file.
- remove unmask status interrupts and add unmask regulator interrupts.
- remove many interrupts check warning print from irq_handler.
- add notifier for regulator event.
- remove unused macro define.
- add PF0900 prefix for IRQ macro define in order to avoid duplication.
- use GENMASK() and BIT() to replace mask marco define
- remove redundant enum pf0900_chip_type.
- remove redundant print info and comments.
- add dvs property present check because this property is optional.
- remove ret == -EINVAL check from sw_set_dvs() function.
- Link to v1: https://lore.kernel.org/imx/20250617102025.3455544-1-joy.zou@nxp.com/

---
Joy Zou (2):
dt-bindings: regulator: add PF0900 regulator yaml
regulator: pf0900: Add PMIC PF0900 support

.../devicetree/bindings/regulator/nxp,pf0900.yaml | 163 ++++
drivers/regulator/Kconfig | 8 +
drivers/regulator/Makefile | 1 +
drivers/regulator/pf0900-regulator.c | 975 +++++++++++++++++++++
4 files changed, 1147 insertions(+)
---
base-commit: 84b92a499e7eca54ba1df6f6c6e01766025943f1
change-id: 20250714-b4-pf09-v2-91cdee6d1272

Best regards,
--
Joy Zou <joy.zou@nxp.com>

show more ...

regulator: add s2dos05 regulator support

S2DOS05 has 1 buck and 4 LDO regulators, used for powering
panel/touchscreen.

Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Link: https://patch.ms

regulator: add s2dos05 regulator support

S2DOS05 has 1 buck and 4 LDO regulators, used for powering
panel/touchscreen.

Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Link: https://patch.msgid.link/20250805-starqltechn_integration_upstream-v8-1-09d8a321fafe@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>

show more ...

regulator: pf0900: Add PMIC PF0900 support

The PF0900 is a power management integrated circuit (PMIC) optimized
for high performance i.MX9x based applications. It features five high
efficiency buck

regulator: pf0900: Add PMIC PF0900 support

The PF0900 is a power management integrated circuit (PMIC) optimized
for high performance i.MX9x based applications. It features five high
efficiency buck converters, three linear and one vaon regulators. It
provides low quiescent current in Standby and low power off Modes.

Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202507221720.jxsGRfcE-lkp@intel.com/
Closes: https://lore.kernel.org/oe-kbuild-all/202506181134.0Hkvy7CK-lkp@intel.com/
Signed-off-by: Joy Zou <joy.zou@nxp.com>
Link: https://patch.msgid.link/20250731-b4-pf09-v2-v3-2-4c2659516582@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>

show more ...

regulator: rpi-panel-v2: Add regulator for 7" Raspberry Pi 720x1280

Add regulator for the 7" Raspberry Pi 720x1280 DSI panel based on ili9881.
This is the Raspberry Pi DSI Panel V2. The newer Raspbe

regulator: rpi-panel-v2: Add regulator for 7" Raspberry Pi 720x1280

Add regulator for the 7" Raspberry Pi 720x1280 DSI panel based on ili9881.
This is the Raspberry Pi DSI Panel V2. The newer Raspberry Pi 5" and 7"
panels have a slightly different register map to the original one. Add a
new driver for this "regulator" chip, this time by exposing two GPIOs and
one PWM controller, both of which can be consumed by panel driver and
pwm-backlight respectively.

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Link: https://patch.msgid.link/20250609000748.1665219-2-marek.vasut+renesas@mailbox.org
Signed-off-by: Mark Brown <broonie@kernel.org>

show more ...

regulator: adp5055: Add driver for adp5055

Add ADI ADP5055 driver support. The device consists
of 3 buck regulators able to connect to high input voltages of up to 18V
with no preregulators.

Signed

regulator: adp5055: Add driver for adp5055

Add ADI ADP5055 driver support. The device consists
of 3 buck regulators able to connect to high input voltages of up to 18V
with no preregulators.

Signed-off-by: Alexis Czezar Torreno <alexisczezar.torreno@analog.com>
Link: https://patch.msgid.link/20250409-upstream-adp5055-v6-2-faa6e810deb1@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>

show more ...

regulator: pf9453: add PMIC PF9453 support

Support new PMIC PF9453, which is totally difference with PCA9450. So
create new file for it.

The PF9453 is a single chip Power Management IC (PMIC) speci

regulator: pf9453: add PMIC PF9453 support

Support new PMIC PF9453, which is totally difference with PCA9450. So
create new file for it.

The PF9453 is a single chip Power Management IC (PMIC) specifically
designed for i.MX 91 processor. It provides power supply solutions for IoT
(Internet of Things), smart appliance, and portable applications where size
and efficiency are critical. The device provides four high efficiency
step-down regulators, three LDOs, one 400 mA load switch and 32.768 kHz
crystal oscillator driver.

Signed-off-by: Joy Zou <joy.zou@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20250314-pf9453-v5-2-ab0cf1f871b0@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>

show more ...