#
8be4d31c |
| 30-Jul-2025 |
Linus Torvalds <torvalds@linux-foundation.org> |
Merge tag 'net-next-6.17' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski: "Core & protocols:
- Wrap datapath globals into net_align
Merge tag 'net-next-6.17' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski: "Core & protocols:
- Wrap datapath globals into net_aligned_data, to avoid false sharing
- Preserve MSG_ZEROCOPY in forwarding (e.g. out of a container)
- Add SO_INQ and SCM_INQ support to AF_UNIX
- Add SIOCINQ support to AF_VSOCK
- Add TCP_MAXSEG sockopt to MPTCP
- Add IPv6 force_forwarding sysctl to enable forwarding per interface
- Make TCP validation of whether packet fully fits in the receive window and the rcv_buf more strict. With increased use of HW aggregation a single "packet" can be multiple 100s of kB
- Add MSG_MORE flag to optimize large TCP transmissions via sockmap, improves latency up to 33% for sockmap users
- Convert TCP send queue handling from tasklet to BH workque
- Improve BPF iteration over TCP sockets to see each socket exactly once
- Remove obsolete and unused TCP RFC3517/RFC6675 loss recovery code
- Support enabling kernel threads for NAPI processing on per-NAPI instance basis rather than a whole device. Fully stop the kernel NAPI thread when threaded NAPI gets disabled. Previously thread would stick around until ifdown due to tricky synchronization
- Allow multicast routing to take effect on locally-generated packets
- Add output interface argument for End.X in segment routing
- MCTP: add support for gateway routing, improve bind() handling
- Don't require rtnl_lock when fetching an IPv6 neighbor over Netlink
- Add a new neighbor flag ("extern_valid"), which cedes refresh responsibilities to userspace. This is needed for EVPN multi-homing where a neighbor entry for a multi-homed host needs to be synced across all the VTEPs among which the host is multi-homed
- Support NUD_PERMANENT for proxy neighbor entries
- Add a new queuing discipline for IETF RFC9332 DualQ Coupled AQM
- Add sequence numbers to netconsole messages. Unregister netconsole's console when all net targets are removed. Code refactoring. Add a number of selftests
- Align IPSec inbound SA lookup to RFC 4301. Only SPI and protocol should be used for an inbound SA lookup
- Support inspecting ref_tracker state via DebugFS
- Don't force bonding advertisement frames tx to ~333 ms boundaries. Add broadcast_neighbor option to send ARP/ND on all bonded links
- Allow providing upcall pid for the 'execute' command in openvswitch
- Remove DCCP support from Netfilter's conntrack
- Disallow multiple packet duplications in the queuing layer
- Prevent use of deprecated iptables code on PREEMPT_RT
Driver API:
- Support RSS and hashing configuration over ethtool Netlink
- Add dedicated ethtool callbacks for getting and setting hashing fields
- Add support for power budget evaluation strategy in PSE / Power-over-Ethernet. Generate Netlink events for overcurrent etc
- Support DPLL phase offset monitoring across all device inputs. Support providing clock reference and SYNC over separate DPLL inputs
- Support traffic classes in devlink rate API for bandwidth management
- Remove rtnl_lock dependency from UDP tunnel port configuration
Device drivers:
- Add a new Broadcom driver for 800G Ethernet (bnge)
- Add a standalone driver for Microchip ZL3073x DPLL
- Remove IBM's NETIUCV device driver
- Ethernet high-speed NICs: - Broadcom (bnxt): - support zero-copy Tx of DMABUF memory - take page size into account for page pool recycling rings - Intel (100G, ice, idpf): - idpf: XDP and AF_XDP support preparations - idpf: add flow steering - add link_down_events statistic - clean up the TSPLL code - preparations for live VM migration - nVidia/Mellanox: - support zero-copy Rx/Tx interfaces (DMABUF and io_uring) - optimize context memory usage for matchers - expose serial numbers in devlink info - support PCIe congestion metrics - Meta (fbnic): - add 25G, 50G, and 100G link modes to phylink - support dumping FW logs - Marvell/Cavium: - support for CN20K generation of the Octeon chips - Amazon: - add HW clock (without timestamping, just hypervisor time access)
- Ethernet virtual: - VirtIO net: - support segmentation of UDP-tunnel-encapsulated packets - Google (gve): - support packet timestamping and clock synchronization - Microsoft vNIC: - add handler for device-originated servicing events - allow dynamic MSI-X vector allocation - support Tx bandwidth clamping
- Ethernet NICs consumer, and embedded: - AMD: - amd-xgbe: hardware timestamping and PTP clock support - Broadcom integrated MACs (bcmgenet, bcmasp): - use napi_complete_done() return value to support NAPI polling - add support for re-starting auto-negotiation - Broadcom switches (b53): - support BCM5325 switches - add bcm63xx EPHY power control - Synopsys (stmmac): - lots of code refactoring and cleanups - TI: - icssg-prueth: read firmware-names from device tree - icssg: PRP offload support - Microchip: - lan78xx: convert to PHYLINK for improved PHY and MAC management - ksz: add KSZ8463 switch support - Intel: - support similar queue priority scheme in multi-queue and time-sensitive networking (taprio) - support packet pre-emption in both - RealTek (r8169): - enable EEE at 5Gbps on RTL8126 - Airoha: - add PPPoE offload support - MDIO bus controller for Airoha AN7583
- Ethernet PHYs: - support for the IPQ5018 internal GE PHY - micrel KSZ9477 switch-integrated PHYs: - add MDI/MDI-X control support - add RX error counters - add cable test support - add Signal Quality Indicator (SQI) reporting - dp83tg720: improve reset handling and reduce link recovery time - support bcm54811 (and its MII-Lite interface type) - air_en8811h: support resume/suspend - support PHY counters for QCA807x and QCA808x - support WoL for QCA807x
- CAN drivers: - rcar_canfd: support for Transceiver Delay Compensation - kvaser: report FW versions via devlink dev info
- WiFi: - extended regulatory info support (6 GHz) - add statistics and beacon monitor for Multi-Link Operation (MLO) - support S1G aggregation, improve S1G support - add Radio Measurement action fields - support per-radio RTS threshold - some work around how FIPS affects wifi, which was wrong (RC4 is used by TKIP, not only WEP) - improvements for unsolicited probe response handling
- WiFi drivers: - RealTek (rtw88): - IBSS mode for SDIO devices - RealTek (rtw89): - BT coexistence for MLO/WiFi7 - concurrent station + P2P support - support for USB devices RTL8851BU/RTL8852BU - Intel (iwlwifi): - use embedded PNVM in (to be released) FW images to fix compatibility issues - many cleanups (unused FW APIs, PCIe code, WoWLAN) - some FIPS interoperability - MediaTek (mt76): - firmware recovery improvements - more MLO work - Qualcomm/Atheros (ath12k): - fix scan on multi-radio devices - more EHT/Wi-Fi 7 features - encapsulation/decapsulation offload - Broadcom (brcm80211): - support SDIO 43751 device
- Bluetooth: - hci_event: add support for handling LE BIG Sync Lost event - ISO: add socket option to report packet seqnum via CMSG - ISO: support SCM_TIMESTAMPING for ISO TS
- Bluetooth drivers: - intel_pcie: support Function Level Reset - nxpuart: add support for 4M baudrate - nxpuart: implement powerup sequence, reset, FW dump, and FW loading"
* tag 'net-next-6.17' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1742 commits) dpll: zl3073x: Fix build failure selftests: bpf: fix legacy netfilter options ipv6: annotate data-races around rt->fib6_nsiblings ipv6: fix possible infinite loop in fib6_info_uses_dev() ipv6: prevent infinite loop in rt6_nlmsg_size() ipv6: add a retry logic in net6_rt_notify() vrf: Drop existing dst reference in vrf_ip6_input_dst net/sched: taprio: align entry index attr validation with mqprio net: fsl_pq_mdio: use dev_err_probe selftests: rtnetlink.sh: remove esp4_offload after test vsock: remove unnecessary null check in vsock_getname() igb: xsk: solve negative overflow of nb_pkts in zerocopy mode stmmac: xsk: fix negative overflow of budget in zerocopy mode dt-bindings: ieee802154: Convert at86rf230.txt yaml format net: dsa: microchip: Disable PTP function of KSZ8463 net: dsa: microchip: Setup fiber ports for KSZ8463 net: dsa: microchip: Write switch MAC address differently for KSZ8463 net: dsa: microchip: Use different registers for KSZ8463 net: dsa: microchip: Add KSZ8463 switch support to KSZ DSA driver dt-bindings: net: dsa: microchip: Add KSZ8463 switch support ...
show more ...
|
Revision tags: v6.16 |
|
#
e9e91870 |
| 26-Jul-2025 |
Jakub Kicinski <kuba@kernel.org> |
Merge branch '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue
Tony Nguyen says:
==================== libie: commonize adminq structure
Michal Swiatkowski says:
It is a p
Merge branch '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue
Tony Nguyen says:
==================== libie: commonize adminq structure
Michal Swiatkowski says:
It is a prework to allow reusing some specific Intel code (eq. fwlog).
Move common *_aq_desc structure to libie header and changing it in ice, ixgbe, i40e and iavf.
Only generic adminq commands can be easily moved to common header, as rest is slightly different. Format remains the same. It will be better to correctly move it when it will be needed to commonize other part of the code.
Move *_aq_str() to new libie module (libie_adminq) and use it across drivers. The functions are exactly the same in each driver. Some more adminq helpers/functions can be moved to libie_adminq when needed.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue: i40e: use libie_aq_str iavf: use libie_aq_str ice: use libie_aq_str libie: add adminq helper for converting err to str iavf: use libie adminq descriptors i40e: use libie adminq descriptors ixgbe: use libie adminq descriptors ice, libie: move generic adminq descriptors to lib ====================
Link: https://patch.msgid.link/20250724182826.3758850-1-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
show more ...
|
Revision tags: v6.16-rc7, v6.16-rc6, v6.16-rc5, v6.16-rc4, v6.16-rc3, v6.16-rc2, v6.16-rc1, v6.15, v6.15-rc7, v6.15-rc6, v6.15-rc5, v6.15-rc4 |
|
#
5feaa7a0 |
| 25-Apr-2025 |
Michal Swiatkowski <michal.swiatkowski@linux.intel.com> |
libie: add adminq helper for converting err to str
Add a new module for common handling of Admin Queue related logic. Start by a helper for error to string conversion. This lives inside libie/, but
libie: add adminq helper for converting err to str
Add a new module for common handling of Admin Queue related logic. Start by a helper for error to string conversion. This lives inside libie/, but is a separate module what follows our logic of splitting into topical modules, to avoid pulling in not needed stuff, and have better organization in general.
Olek suggested how to better solve the error to string conversion.
It will be used in follow-up patches in ice, i40e and iavf.
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Suggested-by: Alexander Lobakin <aleksander.lobakin@intel.com> Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
show more ...
|
Revision tags: v6.15-rc3, v6.15-rc2, v6.15-rc1, v6.14, v6.14-rc7, v6.14-rc6, v6.14-rc5, v6.14-rc4, v6.14-rc3, v6.14-rc2 |
|
#
c771600c |
| 05-Feb-2025 |
Tvrtko Ursulin <tursulin@ursulin.net> |
Merge drm/drm-next into drm-intel-gt-next
We need 4ba4f1afb6a9 ("perf: Generic hotplug support for a PMU with a scope") in order to land a i915 PMU simplification and a fix. That landed in 6.12 and
Merge drm/drm-next into drm-intel-gt-next
We need 4ba4f1afb6a9 ("perf: Generic hotplug support for a PMU with a scope") in order to land a i915 PMU simplification and a fix. That landed in 6.12 and we are stuck at 6.9 so lets bump things forward.
Signed-off-by: Tvrtko Ursulin <tursulin@ursulin.net>
show more ...
|
Revision tags: v6.14-rc1, v6.13, v6.13-rc7, v6.13-rc6, v6.13-rc5, v6.13-rc4, v6.13-rc3, v6.13-rc2, v6.13-rc1, v6.12, v6.12-rc7, v6.12-rc6, v6.12-rc5, v6.12-rc4, v6.12-rc3, v6.12-rc2, v6.12-rc1 |
|
#
36ec807b |
| 20-Sep-2024 |
Dmitry Torokhov <dmitry.torokhov@gmail.com> |
Merge branch 'next' into for-linus
Prepare input updates for 6.12 merge window.
|
Revision tags: v6.11, v6.11-rc7 |
|
#
f057b572 |
| 06-Sep-2024 |
Dmitry Torokhov <dmitry.torokhov@gmail.com> |
Merge branch 'ib/6.11-rc6-matrix-keypad-spitz' into next
Bring in changes removing support for platform data from matrix-keypad driver.
|
Revision tags: v6.11-rc6, v6.11-rc5, v6.11-rc4, v6.11-rc3, v6.11-rc2, v6.11-rc1 |
|
#
3daee2e4 |
| 16-Jul-2024 |
Dmitry Torokhov <dmitry.torokhov@gmail.com> |
Merge tag 'v6.10' into next
Sync up with mainline to bring in device_for_each_child_node_scoped() and other newer APIs.
|
#
66e72a01 |
| 29-Jul-2024 |
Jerome Brunet <jbrunet@baylibre.com> |
Merge tag 'v6.11-rc1' into clk-meson-next
Linux 6.11-rc1
|
#
ee057c8c |
| 14-Aug-2024 |
Steven Rostedt <rostedt@goodmis.org> |
Merge tag 'v6.11-rc3' into trace/ring-buffer/core
The "reserve_mem" kernel command line parameter has been pulled into v6.11. Merge the latest -rc3 to allow the persistent ring buffer memory to be a
Merge tag 'v6.11-rc3' into trace/ring-buffer/core
The "reserve_mem" kernel command line parameter has been pulled into v6.11. Merge the latest -rc3 to allow the persistent ring buffer memory to be able to be mapped at the address specified by the "reserve_mem" command line parameter.
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
show more ...
|
Revision tags: v6.10, v6.10-rc7, v6.10-rc6, v6.10-rc5 |
|
#
8cce4759 |
| 18-Jun-2024 |
Tejun Heo <tj@kernel.org> |
Merge branch 'bpf/for-next' into sched_ext-base
|
#
ed7171ff |
| 16-Aug-2024 |
Lucas De Marchi <lucas.demarchi@intel.com> |
Merge drm/drm-next into drm-xe-next
Get drm-xe-next on v6.11-rc2 and synchronized with drm-intel-next for the display side. This resolves the current conflict for the enable_display module parameter
Merge drm/drm-next into drm-xe-next
Get drm-xe-next on v6.11-rc2 and synchronized with drm-intel-next for the display side. This resolves the current conflict for the enable_display module parameter and allows further pending refactors.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
show more ...
|
#
5c61f598 |
| 12-Aug-2024 |
Thomas Zimmermann <tzimmermann@suse.de> |
Merge drm/drm-next into drm-misc-next
Get drm-misc-next to the state of v6.11-rc2.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
|
#
3663e2c4 |
| 01-Aug-2024 |
Jani Nikula <jani.nikula@intel.com> |
Merge drm/drm-next into drm-intel-next
Sync with v6.11-rc1 in general, and specifically get the new BACKLIGHT_POWER_ constants for power states.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
#
4436e6da |
| 02-Aug-2024 |
Thomas Gleixner <tglx@linutronix.de> |
Merge branch 'linus' into x86/mm
Bring x86 and selftests up to date
|
#
a1ff5a7d |
| 30-Jul-2024 |
Maxime Ripard <mripard@kernel.org> |
Merge drm/drm-fixes into drm-misc-fixes
Let's start the new drm-misc-fixes cycle by bringing in 6.11-rc1.
Signed-off-by: Maxime Ripard <mripard@kernel.org>
|
#
afeea275 |
| 04-Jul-2024 |
Maxime Ripard <mripard@kernel.org> |
Merge drm-misc-next-2024-07-04 into drm-misc-next-fixes
Let's start the drm-misc-next-fixes cycle.
Signed-off-by: Maxime Ripard <mripard@kernel.org>
|
#
d754ed28 |
| 19-Jun-2024 |
Jani Nikula <jani.nikula@intel.com> |
Merge drm/drm-next into drm-intel-next
Sync to v6.10-rc3.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
Revision tags: v6.10-rc4 |
|
#
89aa02ed |
| 12-Jun-2024 |
Rodrigo Vivi <rodrigo.vivi@intel.com> |
Merge drm/drm-next into drm-xe-next
Needed to get tracing cleanup and add mmio tracing series.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
#
92815da4 |
| 12-Jun-2024 |
Dmitry Baryshkov <dmitry.baryshkov@linaro.org> |
Merge remote-tracking branch 'drm-misc/drm-misc-next' into HEAD
Merge drm-misc-next tree into the msm-next tree in order to be able to use HDMI connector framework for the MSM HDMI driver.
|
Revision tags: v6.10-rc3, v6.10-rc2 |
|
#
375c4d15 |
| 27-May-2024 |
Maxime Ripard <mripard@kernel.org> |
Merge drm/drm-next into drm-misc-next
Let's start the new release cycle.
Signed-off-by: Maxime Ripard <mripard@kernel.org>
|
#
51835949 |
| 17-Jul-2024 |
Linus Torvalds <torvalds@linux-foundation.org> |
Merge tag 'net-next-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski: "Not much excitement - a handful of large patchsets (devmem a
Merge tag 'net-next-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski: "Not much excitement - a handful of large patchsets (devmem among them) did not make it in time.
Core & protocols:
- Use local_lock in addition to local_bh_disable() to protect per-CPU resources in networking, a step closer for local_bh_disable() not to act as a big lock on PREEMPT_RT
- Use flex array for netdevice priv area, ensure its cache alignment
- Add a sysctl knob to allow user to specify a default rto_min at socket init time. Bit of a big hammer but multiple companies were independently carrying such patch downstream so clearly it's useful
- Support scheduling transmission of packets based on CLOCK_TAI
- Un-pin TCP TIMEWAIT timer to avoid it firing on CPUs later cordoned off using cpusets
- Support multiple L2TPv3 UDP tunnels using the same 5-tuple address
- Allow configuration of multipath hash seed, to both allow synchronizing hashing of two routers, and preventing partial accidental sync
- Improve TCP compliance with RFC 9293 for simultaneous connect()
- Support sending NAT keepalives in IPsec ESP in UDP states. Userspace IKE daemon had to do this before, but the kernel can better keep track of it
- Support sending supervision HSR frames with MAC addresses stored in ProxyNodeTable when RedBox (i.e. HSR-SAN) is enabled
- Introduce IPPROTO_SMC for selecting SMC when socket is created
- Allow UDP GSO transmit from devices with no checksum offload
- openvswitch: add packet sampling via psample, separating the sampled traffic from "upcall" packets sent to user space for forwarding
- nf_tables: shrink memory consumption for transaction objects
Things we sprinkled into general kernel code:
- Power Sequencing subsystem (used by Qualcomm Bluetooth driver for QCA6390) [ Already merged separately - Linus ]
- Add IRQ information in sysfs for auxiliary bus
- Introduce guard definition for local_lock
- Add aligned flavor of __cacheline_group_{begin, end}() markings for grouping fields in structures
BPF:
- Notify user space (via epoll) when a struct_ops object is getting detached/unregistered
- Add new kfuncs for a generic, open-coded bits iterator
- Enable BPF programs to declare arrays of kptr, bpf_rb_root, and bpf_list_head
- Support resilient split BTF which cuts down on duplication and makes BTF as compact as possible WRT BTF from modules
- Add support for dumping kfunc prototypes from BTF which enables both detecting as well as dumping compilable prototypes for kfuncs
- riscv64 BPF JIT improvements in particular to add 12-argument support for BPF trampolines and to utilize bpf_prog_pack for the latter
- Add the capability to offload the netfilter flowtable in XDP layer through kfuncs
Driver API:
- Allow users to configure IRQ tresholds between which automatic IRQ moderation can choose
- Expand Power Sourcing (PoE) status with power, class and failure reason. Support setting power limits
- Track additional RSS contexts in the core, make sure configuration changes don't break them
- Support IPsec crypto offload for IPv6 ESP and IPv4 UDP-encapsulated ESP data paths
- Support updating firmware on SFP modules
Tests and tooling:
- mptcp: use net/lib.sh to manage netns
- TCP-AO and TCP-MD5: replace debug prints used by tests with tracepoints
- openvswitch: make test self-contained (don't depend on OvS CLI tools)
Drivers:
- Ethernet high-speed NICs: - Broadcom (bnxt): - increase the max total outstanding PTP TX packets to 4 - add timestamping statistics support - implement netdev_queue_mgmt_ops - support new RSS context API - Intel (100G, ice, idpf): - implement FEC statistics and dumping signal quality indicators - support E825C products (with 56Gbps PHYs) - nVidia/Mellanox: - support HW-GRO - mlx4/mlx5: support per-queue statistics via netlink - obey the max number of EQs setting in sub-functions - AMD/Solarflare: - support new RSS context API - AMD/Pensando: - ionic: rework fix for doorbell miss to lower overhead and skip it on new HW - Wangxun: - txgbe: support Flow Director perfect filters
- Ethernet NICs consumer, embedded and virtual: - Add driver for Tehuti Networks TN40xx chips - Add driver for Meta's internal NIC chips - Add driver for Ethernet MAC on Airoha EN7581 SoCs - Add driver for Renesas Ethernet-TSN devices - Google cloud vNIC: - flow steering support - Microsoft vNIC: - support page sizes other than 4KB on ARM64 - vmware vNIC: - support latency measurement (update to version 9) - VirtIO net: - support for Byte Queue Limits - support configuring thresholds for automatic IRQ moderation - support for AF_XDP Rx zero-copy - Synopsys (stmmac): - support for STM32MP13 SoC - let platforms select the right PCS implementation - TI: - icssg-prueth: add multicast filtering support - icssg-prueth: enable PTP timestamping and PPS - Renesas: - ravb: improve Rx performance 30-400% by using page pool, theaded NAPI and timer-based IRQ coalescing - ravb: add MII support for R-Car V4M - Cadence (macb): - macb: add ARP support to Wake-On-LAN - Cortina: - use phylib for RX and TX pause configuration
- Ethernet switches: - nVidia/Mellanox: - support configuration of multipath hash seed - report more accurate max MTU - use page_pool to improve Rx performance - MediaTek: - mt7530: add support for bridge port isolation - Qualcomm: - qca8k: add support for bridge port isolation - Microchip: - lan9371/2: add 100BaseTX PHY support - NXP: - vsc73xx: implement VLAN operations
- Ethernet PHYs: - aquantia: enable support for aqr115c - aquantia: add support for PHY LEDs - realtek: add support for rtl8224 2.5Gbps PHY - xpcs: add memory-mapped device support - add BroadR-Reach link mode and support in Broadcom's PHY driver
- CAN: - add document for ISO 15765-2 protocol support - mcp251xfd: workaround for erratum DS80000789E, use timestamps to catch when device returns incorrect FIFO status
- WiFi: - mac80211/cfg80211: - parse Transmit Power Envelope (TPE) data in mac80211 instead of in drivers - improvements for 6 GHz regulatory flexibility - multi-link improvements - support multiple radios per wiphy - remove DEAUTH_NEED_MGD_TX_PREP flag - Intel (iwlwifi): - bump FW API to 91 for BZ/SC devices - report 64-bit radiotap timestamp - enable P2P low latency by default - handle Transmit Power Envelope (TPE) advertised by AP - remove support for older FW for new devices - fast resume (keeping the device configured) - mvm: re-enable Multi-Link Operation (MLO) - aggregation (A-MSDU) optimizations - MediaTek (mt76): - mt7925 Multi-Link Operation (MLO) support - Qualcomm (ath10k): - LED support for various chipsets - Qualcomm (ath12k): - remove unsupported Tx monitor handling - support channel 2 in 6 GHz band - support Spatial Multiplexing Power Save (SMPS) in 6 GHz band - supprt multiple BSSID (MBSSID) and Enhanced Multi-BSSID Advertisements (EMA) - support dynamic VLAN - add panic handler for resetting the firmware state - DebugFS support for datapath statistics - WCN7850: support for Wake on WLAN - Microchip (wilc1000): - read MAC address during probe to make it visible to user space - suspend/resume improvements - TI (wl18xx): - support newer firmware versions - RealTek (rtw89): - preparation for RTL8852BE-VT support - Wake on WLAN support for WiFi 6 chips - 36-bit PCI DMA support - RealTek (rtlwifi): - RTL8192DU support - Broadcom (brcmfmac): - Management Frame Protection support (to enable WPA3)
- Bluetooth: - qualcomm: use the power sequencer for QCA6390 - btusb: mediatek: add ISO data transmission functions - hci_bcm4377: add BCM4388 support - btintel: add support for BlazarU core - btintel: add support for Whale Peak2 - btnxpuart: add support for AW693 A1 chipset - btnxpuart: add support for IW615 chipset - btusb: add Realtek RTL8852BE support ID 0x13d3:0x3591"
* tag 'net-next-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1589 commits) eth: fbnic: Fix spelling mistake "tiggerring" -> "triggering" tcp: Replace strncpy() with strscpy() wifi: ath12k: fix build vs old compiler tcp: Don't access uninit tcp_rsk(req)->ao_keyid in tcp_create_openreq_child(). eth: fbnic: Write the TCAM tables used for RSS control and Rx to host eth: fbnic: Add L2 address programming eth: fbnic: Add basic Rx handling eth: fbnic: Add basic Tx handling eth: fbnic: Add link detection eth: fbnic: Add initial messaging to notify FW of our presence eth: fbnic: Implement Rx queue alloc/start/stop/free eth: fbnic: Implement Tx queue alloc/start/stop/free eth: fbnic: Allocate a netdevice and napi vectors with queues eth: fbnic: Add FW communication mechanism eth: fbnic: Add message parsing for FW messages eth: fbnic: Add register init to set PCIe/Ethernet device config eth: fbnic: Allocate core device specific structures and devlink interface eth: fbnic: Add scaffolding for Meta's NIC driver PCI: Add Meta Platforms vendor ID net/sched: cls_flower: propagate tca[TCA_OPTIONS] to NL_REQ_ATTR_CHECK ...
show more ...
|
#
bb678f01 |
| 11-Jun-2024 |
Jakub Kicinski <kuba@kernel.org> |
Merge branch 'intel-wired-lan-driver-updates-2024-06-03'
Jacob Keller says:
==================== Intel Wired LAN Driver Updates 2024-06-03
This series includes miscellaneous improvements for the i
Merge branch 'intel-wired-lan-driver-updates-2024-06-03'
Jacob Keller says:
==================== Intel Wired LAN Driver Updates 2024-06-03
This series includes miscellaneous improvements for the ice as well as a cleanup to the Makefiles for all Intel net drivers.
Andy fixes all of the Intel net driver Makefiles to use the documented '*-y' syntax for specifying object files to link into kernel driver modules, rather than the '*-objs' syntax which works but is documented as reserved for user-space host programs.
Jacob has a cleanup to refactor rounding logic in the ice driver into a common roundup_u64 helper function.
Michal Schmidt replaces irq_set_affinity_hint() to use irq_update_affinity_hint() which behaves better with user-applied affinity settings.
v2: https://lore.kernel.org/r/20240605-next-2024-06-03-intel-next-batch-v2-0-39c23963fa78@intel.com v1: https://lore.kernel.org/r/20240603-next-2024-06-03-intel-next-batch-v1-0-e0523b28f325@intel.com ====================
Link: https://lore.kernel.org/r/20240607-next-2024-06-03-intel-next-batch-v3-0-d1470cee3347@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
show more ...
|
#
a2fe35df |
| 07-Jun-2024 |
Andy Shevchenko <andriy.shevchenko@linux.intel.com> |
net: intel: Use *-y instead of *-objs in Makefile
*-objs suffix is reserved rather for (user-space) host programs while usually *-y suffix is used for kernel drivers (although *-objs works for that
net: intel: Use *-y instead of *-objs in Makefile
*-objs suffix is reserved rather for (user-space) host programs while usually *-y suffix is used for kernel drivers (although *-objs works for that purpose for now).
Let's correct the old usages of *-objs in Makefiles.
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://lore.kernel.org/r/20240607-next-2024-06-03-intel-next-batch-v3-1-d1470cee3347@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
show more ...
|
#
0c8ea05e |
| 04-Jul-2024 |
Peter Zijlstra <peterz@infradead.org> |
Merge branch 'tip/x86/cpu'
The Lunarlake patches rely on the new VFM stuff.
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
|
#
594ce0b8 |
| 10-Jun-2024 |
Russell King (Oracle) <rmk+kernel@armlinux.org.uk> |
Merge topic branches 'clkdev' and 'fixes' into for-linus
|