Merge tag 'asoc-fix-v6.18-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus

ASoC: Fixes for v6.18

A moderately large collection of driver specific fixes, plus a f

Merge tag 'asoc-fix-v6.18-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus

ASoC: Fixes for v6.18

A moderately large collection of driver specific fixes, plus a few new
quirks and device IDs. The NAU8821 changes are a little large but more
in mechanical ways than in ways that are complex.

show more ...

Merge drm/drm-fixes into drm-misc-fixes

Updating drm-misc-fixes to the state of v6.18-rc1.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>

Merge tag 'mtd/for-6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux

Pull MTD updates from Miquel Raynal:
"MTD core:
- Bad blocks increment is skipped if the block is already know

Merge tag 'mtd/for-6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux

Pull MTD updates from Miquel Raynal:
"MTD core:
- Bad blocks increment is skipped if the block is already known bad
(improves user statistics relevance)
- Expose the OOB layout via debugfs

Raw NAND:
- Add support for Loongson-2K1000 and Loongson-2K0500 NAND
controllers, including extra features, such as chip select
and 6-byte NAND ID reading support
- Drop the s3c2410 driver

SPI NAND:
- Important SPI NAND continuous read improvements and fixes
- Add support for FudanMicro FM25S01A
- Add support for continuous reads in Gigadevice vendor driver

ECC:
- Add support for the Realtek ECC engine

SPI NOR:

- Some flashes can't perform reads or writes with start or end being
an odd number in Octal DTR mode. File systems like UBIFS can
request such reads or writes, causing the transaction to error out.

Pad the read or write transactions with extra bytes to avoid this
problem.

And the usual amount of various miscellaneous fixes"

* tag 'mtd/for-6.18' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (46 commits)
mtd: rawnand: sunxi: drop unused module alias
mtd: rawnand: stm32_fmc2: drop unused module alias
mtd: rawnand: rockchip: drop unused module alias
mtd: rawnand: pl353: drop unused module alias
mtd: rawnand: omap2: drop unused module alias
mtd: rawnand: atmel: drop unused module alias
mtd: onenand: omap2: drop unused module alias
mtd: hyperbus: hbmc-am654: drop unused module alias
mtd: jedec_probe: use struct_size() helper for cfiq allocation
mtd: cfi: use struct_size() helper for cfiq allocation
mtd: nand: raw: gpmi: fix clocks when CONFIG_PM=N
mtd: rawnand: omap2: fix device leak on probe failure
mtd: rawnand: atmel: Fix error handling path in atmel_nand_controller_add_nands
mtd: nand: realtek-ecc: Add Realtek external ECC engine support
dt-bindings: mtd: Add realtek,rtl9301-ecc
mtd: spinand: repeat reading in regular mode if continuous reading fails
mtd: spinand: try a regular dirmap if creating a dirmap for continuous reading fails
mtd: spinand: fix direct mapping creation sizes
mtd: rawnand: fsmc: Default to autodetect buswidth
mtd: nand: move nand_check_erased_ecc_chunk() to nand/core
...

show more ...

Merge tag 'nand/for-6.18' into mtd/next

* Raw NAND:
- Add support for Loongson-2K1000 and Loongson-2K0500 NAND controllers,
including extra features, such as chip select and 6-byte NAND ID
readi

Merge tag 'nand/for-6.18' into mtd/next

* Raw NAND:
- Add support for Loongson-2K1000 and Loongson-2K0500 NAND controllers,
including extra features, such as chip select and 6-byte NAND ID
reading support.
- Drop the s3c2410 driver.

* SPI NAND:
- Important SPI NAND continuous read improvements and fixes.
- Add support for FudanMicro FM25S01A.
- Add support for continuous reads in Gigadevice vendor driver.

* ECC:
- Add support for the Realtek ECC engine.

This PR comes with the usual amount of various miscellaneous fixes.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>

show more ...

mtd: rawnand: loongson: Add Loongson-2K1000 NAND controller support

The Loongson-2K1000 NAND controller is also similar to the Loongson-1C.

It supports a maximum capacity of 16GB FLASH per chip wit

mtd: rawnand: loongson: Add Loongson-2K1000 NAND controller support

The Loongson-2K1000 NAND controller is also similar to the Loongson-1C.

It supports a maximum capacity of 16GB FLASH per chip with a maximum
page size of 8KB, and it supports up to 4 chip selects and 4 RDY
signals.

The key difference from the Loongson-2K0500 is that it requires explicit
configuration of the DMA control route. Typically, it is configured as
APBDMA0.

Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>

show more ...

mtd: rawnand: loongson: Add Loongson-2K0500 NAND controller support

The Loongson-2K0500 NAND controller is similar to the Loongson-1C.

It supports a maximum capacity of 16GB FLASH per chip with a m

mtd: rawnand: loongson: Add Loongson-2K0500 NAND controller support

The Loongson-2K0500 NAND controller is similar to the Loongson-1C.

It supports a maximum capacity of 16GB FLASH per chip with a maximum
page size of 8KB, and it supports up to 4 chip selects and 4 RDY
signals.

Its DMA controller is defaulted to APBDMA0.

Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>

show more ...

mtd: rawnand: loongson: Add nand chip select support

The page address register describes the page address of the starting
address for NAND read/write/erase operations.

According to the manual, it c

mtd: rawnand: loongson: Add nand chip select support

The page address register describes the page address of the starting
address for NAND read/write/erase operations.

According to the manual, it consists of two parts:
{chip select, page number}

The `chip select` is fixed at 2 bits, and the `page number` is
determined based on the actual capacity of the single-chip memory.
Therefore we need to determine the `chip select` bits base on the `page
number`.

For example, for a 1GB capacity chip (2K page size), it has 1M pages.
Thus, [19:0] is used to represent the page number, and [21:20]
represents the chip select.

Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>

show more ...

mtd: rawnand: loongson: Add 6-byte NAND ID reading support

Loongson-1C and Loongson-2K SoCs support NAND flash chips with 6-byte ID.
However, the current implementation only handles 5-byte ID which

mtd: rawnand: loongson: Add 6-byte NAND ID reading support

Loongson-1C and Loongson-2K SoCs support NAND flash chips with 6-byte ID.
However, the current implementation only handles 5-byte ID which can lead
to incorrect chip detection.

Extend loongson_nand_read_id_type_exec() to support 6-byte NAND ID.

Signed-off-by: Keguang Zhang <keguang.zhang@gmail.com>
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>

show more ...

mtd: rawnand: loongson1: Rename the prefix from ls1x to loongson

I am going to introduce the NAND controllers of the Loongson-2K series
CPUs, which are similar to Loongson-1.

As preparation, rename

mtd: rawnand: loongson1: Rename the prefix from ls1x to loongson

I am going to introduce the NAND controllers of the Loongson-2K series
CPUs, which are similar to Loongson-1.

As preparation, rename all prefixes from Loongson1-specific to
Loongson-generic.

No functional change intended.

Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>

show more ...