Merge tag 'leds-next-6.14' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds

Pull LED updates from Lee Jones:

- Allow struct bin_attribute instances to be placed in read-only memory
for

Merge tag 'leds-next-6.14' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds

Pull LED updates from Lee Jones:

- Allow struct bin_attribute instances to be placed in read-only memory
for enhanced protection

- Fix a memory leak in the cht-wcove driver by using
devm_led_classdev_register()

- Fix an OF node reference leak in the netxbig driver

- Ensure PWM is disabled properly in pwm-multicolor suspend

- Add support for Texas Instruments LP8864, LP8864S, LP8866
LED-backlight drivers

- Add support for STMicroelectronics's LED1202 12-channel LED driver

- Convert LP8860 bindings to YAML format

- Add bindings for the TI LP8864/LP8866 LED drivers

- Add LED1202 LED controller bindings

- Fix path to color definitions in leds-class-multicolor.yaml

- Add pm660l compatible to qcom,spmi-flash-led bindings

- Extend cznic,turris-omnia-leds binding with interrupts property

- Add documentation for the STMicroelectronics LED1202 driver

- Add entry for AAEON UP board FPGA drivers in MAINTAINERS

- Fix a wrong format specifier in the ledtrig-activity driver

- Fix a bug in the lp8860 driver where only half of the EEPROM was
written

* tag 'leds-next-6.14' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds: (28 commits)
leds: triggers: Constify 'struct bin_attribute'
leds: cht-wcove: Use devm_led_classdev_register() to avoid memory leak
leds: lp8864: Add support for Texas Instruments LP8864, LP8864S, LP8866 LED-backlights
dt-bindings: leds: Convert LP8860 into YAML format
leds: Add LED1202 I2C driver
dt-bindings: leds: Add LED1202 LED Controller
Documentation:leds: Add leds-st1202.rst
leds: pwm-multicolor: Disable PWM when going to suspend
leds: netxbig: Fix an OF node reference leak in netxbig_leds_get_of_pdata()
turris-omnia-mcu-interface.h: Move macro definitions outside of enums
MAINTAINERS: Add entry for AAEON UP board FPGA drivers
leds: Add AAEON UP board LED driver
leds: trigger: netdev: Check offload ability on interface up
leds: turris-omnia: Use uppercase first letter in all comments
leds: turris-omnia: Use dev_err_probe() where appropriate
leds: turris-omnia: Inform about missing LED gamma correction feature in the MCU driver
platform: cznic: turris-omnia-mcu: Inform about missing LED panel brightness change interrupt feature
leds: turris-omnia: Notify sysfs on MCU global LEDs brightness change
leds: turris-omnia: Document driver private structures
dt-bindings: leds: cznic,turris-omnia-leds: Allow interrupts property
...

show more ...

Merge tag 'mfd-next-6.14' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd

Pull mfd updates from Lee Jones:

- Fix race in device_node_get_regmap() using more extensive locking

- Remove u

Merge tag 'mfd-next-6.14' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd

Pull mfd updates from Lee Jones:

- Fix race in device_node_get_regmap() using more extensive locking

- Remove unused platform driver support for syscon

- Allow syscon nodes to be registered without a "syscon" compatible
string

- Make `platform_data` pointer const in struct mfd_cell

- Revert support for multiple AXP PMICs to avoid regressions

- Increase SoundWire attach timeout and use gpiod_set_raw() for GPIO
operation

- Store the result from fault_log() for use by other sub-components

- Fix an invalid regmap-config max_register value

- Add another Gemini Lake ISA bridge PCI device ID

- Use devm_register_power_off_handler() to simplify code

- Add support for QNAP microcontroller units, including LEDs, input,
and hwmon

- Use MFD_CELL macros and remove unused code

- Add support for AAEON UP board FPGA

- Remove unused includes

- Fix various typos and compatibility issues in multiple bindings

- Add new bindings for rk3562 QoS, LED1202, and qcom,tcsr-ipq5424

- Convert several bindings to YAML schema

- Update sprd,sc2731 bindings to reference sprd,sc2731-efuse bindings
directly

- Fix rohm,bd71815 bindings by correcting resistor values and typos

- Documentation improvements:
- Add documentation for LED1202 and qnap-mcu-hwmon
- Adjust the file entry for the qnap-mcu header in MAINTAINERS

* tag 'mfd-next-6.14' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (35 commits)
MAINTAINERS: Adjust the file entry for the qnap-mcu header
dt-bindings: mfd: syscon: Fix ti,j784s4-acspcie-proxy-ctrl compatible
dt-bindings: mfd: syscon: Fix al,alpine-sysfabric-service compatible
Revert "mfd: axp20x: Allow multiple regulators"
dt-bindings: mfd: syscon: Add rk3562 QoS register compatible
mfd: syscon: Allow syscon nodes without a "syscon" compatible
mfd: syscon: Remove the platform driver support
mfd: syscon: Fix race in device_node_get_regmap()
dt-bindings: mfd: atmel: Convert to YAML schema
dt-bindings: mfd: atmel,at91sam9260: Convert to YAML schema
dt-bindings: mfd: sprd,sc2731: Reference sprd,sc2731-efuse bindings
mfd: tps65219: Remove unused macros & add regmap.h
mfd: tps65219: Use MFD_CELL macros
leds: Add LED1202 I2C driver
dt-bindings: leds: Add LED1202 LED Controller
Documentation:leds: Add leds-st1202.rst
mfd: Add support for AAEON UP board FPGA
mfd: da9052: Store result from fault_log
mfd: intel_soc_pmic_chtdc_ti: Fix invalid regmap-config max_register value
mfd: cs42l43: Use devres for remove as well
...

show more ...

Merge branch 'next' into for-linus

Prepare input updates for 6.14 merge window.

leds: lp8864: Add support for Texas Instruments LP8864, LP8864S, LP8866 LED-backlights

Add driver for TI LP8864, LP8864S, LP8866 4/6 channel LED-backlight drivers
with I2C interface.

Link: https://

leds: lp8864: Add support for Texas Instruments LP8864, LP8864S, LP8866 LED-backlights

Add driver for TI LP8864, LP8864S, LP8866 4/6 channel LED-backlight drivers
with I2C interface.

Link: https://www.ti.com/lit/gpn/lp8864-q1
Link: https://www.ti.com/lit/gpn/lp8864s-q1
Link: https://www.ti.com/lit/gpn/lp8866-q1
Link: https://www.ti.com/lit/gpn/lp8866s-q1
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Link: https://lore.kernel.org/r/20241218210829.73191-3-alexander.sverdlin@siemens.com
Signed-off-by: Lee Jones <lee@kernel.org>

show more ...

leds: Add LED1202 I2C driver

The output current can be adjusted separately for each channel by 8-bit
analog (current sink input) and 12-bit digital (PWM) dimming control. The
LED1202 implements 12 l

leds: Add LED1202 I2C driver

The output current can be adjusted separately for each channel by 8-bit
analog (current sink input) and 12-bit digital (PWM) dimming control. The
LED1202 implements 12 low-side current generators with independent dimming
control.
Internal volatile memory allows the user to store up to 8 different patterns,
each pattern is a particular output configuration in terms of PWM
duty-cycle (on 4096 steps). Analog dimming (on 256 steps) is per channel but
common to all patterns. Each device tree LED node will have a corresponding
entry in /sys/class/leds with the label name. The brightness property
corresponds to the per channel analog dimming, while the patterns[1-8] to the
PWM dimming control.

Signed-off-by: Vicentiu Galanopulo <vicentiu.galanopulo@remote-tech.co.uk>
Link: https://lore.kernel.org/r/20241218183401.41687-4-vicentiu.galanopulo@remote-tech.co.uk
Signed-off-by: Lee Jones <lee@kernel.org>

show more ...

leds: Add LED1202 I2C driver

The output current can be adjusted separately for each channel by 8-bit
analog (current sink input) and 12-bit digital (PWM) dimming control. The
LED1202 implements 12 l

leds: Add LED1202 I2C driver

The output current can be adjusted separately for each channel by 8-bit
analog (current sink input) and 12-bit digital (PWM) dimming control. The
LED1202 implements 12 low-side current generators with independent dimming
control.
Internal volatile memory allows the user to store up to 8 different patterns,
each pattern is a particular output configuration in terms of PWM
duty-cycle (on 4096 steps). Analog dimming (on 256 steps) is per channel but
common to all patterns. Each device tree LED node will have a corresponding
entry in /sys/class/leds with the label name. The brightness property
corresponds to the per channel analog dimming, while the patterns[1-8] to the
PWM dimming control.

Signed-off-by: Vicentiu Galanopulo <vicentiu.galanopulo@remote-tech.co.uk>
Link: https://lore.kernel.org/r/20241218182001.41476-4-vicentiu.galanopulo@remote-tech.co.uk
Signed-off-by: Lee Jones <lee@kernel.org>

show more ...

Merge tag 'v6.13-rc3' into next

Sync up with the mainline.

leds: Add AAEON UP board LED driver

Add support for LEDs on AAEON UP boards. These leds are managed by the
onboard FPGA:
- UP boards: yellow, green, red
- UP Squared boards: blue, yellow, green, red

leds: Add AAEON UP board LED driver

Add support for LEDs on AAEON UP boards. These leds are managed by the
onboard FPGA:
- UP boards: yellow, green, red
- UP Squared boards: blue, yellow, green, red

Based on the work done by Gary Wang <garywang@aaeon.com.tw>, largely
rewritten.

Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://lore.kernel.org/r/20241211-aaeon-up-board-pinctrl-support-v1-2-24719be27631@bootlin.com
Signed-off-by: Lee Jones <lee@kernel.org>

show more ...

leds: Add driver for LEDs from qnap-mcu devices

This adds a driver that connects to the qnap-mcu mfd driver and provides
access to the LEDs on it.

Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Li

leds: Add driver for LEDs from qnap-mcu devices

This adds a driver that connects to the qnap-mcu mfd driver and provides
access to the LEDs on it.

Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20241107114712.538976-6-heiko@sntech.de
Signed-off-by: Lee Jones <lee@kernel.org>

show more ...

leds: turris-omnia: Notify sysfs on MCU global LEDs brightness change

Recall that on Turris Omnia, the LED controller has a global brightness
property, which allows the user to make the front LED pa

leds: turris-omnia: Notify sysfs on MCU global LEDs brightness change

Recall that on Turris Omnia, the LED controller has a global brightness
property, which allows the user to make the front LED panel dimmer.

There is also a button on the front panel, which by default is
configured so that pressing it changes the global brightness to a lower
value (unless it is at 0%, in which case pressing the button changes the
global brightness to 100%).

Newer versions of the MCU firmware support informing the SOC that the
brightness was changed by button press event via an interrupt.

Now that we have the turris-omnia-mcu driver, which adds support for MCU
interrupts, add the ability to inform the userspace (via a sysfs
notification) that the global brightness was changed.

Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://lore.kernel.org/r/20241111100355.6978-8-kabel@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>

show more ...

leds: turris-omnia: Use command execution functions from the MCU driver

Use the MCU command execution functions from the MCU driver instead of
the ad-hoc implementation in the LED driver. This allow

leds: turris-omnia: Use command execution functions from the MCU driver

Use the MCU command execution functions from the MCU driver instead of
the ad-hoc implementation in the LED driver. This allows as to drop the
LED driver implementation, which is a duplicate.

Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://lore.kernel.org/r/20241111100355.6978-3-kabel@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>

show more ...

Merge tag 'v6.12-rc3' into perf-tools-next

To get the fixes in the current perf-tools tree.

Signed-off-by: Namhyung Kim <namhyung@kernel.org>

Merge tag 'v6.12-rc1' into clk-meson-next

Linux 6.12-rc1

Merge net-next/main to resolve conflicts

The wireless-next tree was based on something older, and there
are now conflicts between -rc2 and work here. Merge net-next,
which has enough of -rc2 for the

Merge net-next/main to resolve conflicts

The wireless-next tree was based on something older, and there
are now conflicts between -rc2 and work here. Merge net-next,
which has enough of -rc2 for the conflicts to happen, resolving
them in the process.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

show more ...

Merge drm/drm-next into drm-xe-next

Backmerging to resolve a conflict with core locally.

Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>

Merge drm/drm-next into drm-misc-next

Get drm-misc-next to up v6.12-rc1.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>

Merge drm/drm-next into drm-intel-next

Sync to v6.12-rc1.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>

Merge branch 'for-6.13/wacom' into for-linus

- Sanitization of BTN_TOOL_RUBBER handling (Jason Gerecke)

Merge remote-tracking branch 'torvalds/master' into perf-tools

To pick up changes in other trees that may affect perf, such as libbpf
and in general the header files that perf has copies of, so that

Merge remote-tracking branch 'torvalds/master' into perf-tools

To pick up changes in other trees that may affect perf, such as libbpf
and in general the header files that perf has copies of, so that we can
do the sync with the kernel sources.

Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

show more ...

Merge tag 'kvmarm-fixes-6.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD

KVM/arm64 fixes for 6.12, take #1

- Fix pKVM error path on init, making sure we do not chang

Merge tag 'kvmarm-fixes-6.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD

KVM/arm64 fixes for 6.12, take #1

- Fix pKVM error path on init, making sure we do not change critical
system registers as we're about to fail

- Make sure that the host's vector length is at capped by a value
common to all CPUs

- Fix kvm_has_feat*() handling of "negative" features, as the current
code is pretty broken

- Promote Joey to the status of official reviewer, while James steps
down -- hopefully only temporarly

show more ...

Merge tag 'asoc-fix-v6.12-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus

ASoC: Fixes for v6.12

A bunch of fixes here that came in during the merge window and t

Merge tag 'asoc-fix-v6.12-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus

ASoC: Fixes for v6.12

A bunch of fixes here that came in during the merge window and the first
week of release, plus some new quirks and device IDs. There's nothing
major here, it's a bit bigger than it might've been due to there being
no fixes sent during the merge window due to your vacation.

show more ...

Merge remote-tracking branch 'drm/drm-fixes' into drm-misc-fixes

Required for a panthor fix that broke when
FOP_UNSIGNED_OFFSET was added in place of FMODE_UNSIGNED_OFFSET.

Signed-off-by: Maarten L

Merge remote-tracking branch 'drm/drm-fixes' into drm-misc-fixes

Required for a panthor fix that broke when
FOP_UNSIGNED_OFFSET was added in place of FMODE_UNSIGNED_OFFSET.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>

show more ...

Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net

Cross-merge networking fixes after downstream PR.

No conflicts and no adjacent changes.

Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Merge branch 'next' into for-linus

Prepare input updates for 6.12 merge window.

Merge branch 'ib/6.11-rc6-matrix-keypad-spitz' into next

Bring in changes removing support for platform data from matrix-keypad
driver.