History log of /linux/drivers/iio/adc/Makefile (Results 1 – 25 of 199)
Revision Date Author Comments
# 508bdb49 16-Sep-2026 Janani Sunil <janani.sunil@analog.com>

iio: adc: Add AD7768 and AD7768-4 core support

Add core support for the AD7768 and AD7768-4 simultaneous sampling ADCs.
Configure supplies, clock and reset, use a custom regmap bus for the SPI
proto

iio: adc: Add AD7768 and AD7768-4 core support

Add core support for the AD7768 and AD7768-4 simultaneous sampling ADCs.
Configure supplies, clock and reset, use a custom regmap bus for the SPI
protocol, and parse the enabled channels and input buffer settings from
devicetree.

Connect the converter to an IIO backend for buffered capture with CRC,
provide a fixed safe wideband sampling configuration and add runtime
power management.

Signed-off-by: Janani Sunil <janani.sunil@analog.com>
Signed-off-by: Jonathan Cameron <jonathan.cameron@oss.qualcomm.com>

show more ...


# 309bd010 31-Aug-2026 Stefan Popa <stefan.popa@analog.com>

iio: adc: add MAX40080 current-sense amplifier driver

The MAX40080 is a bidirectional current-sense amplifier with an
integrated 12-bit ADC and an I2C/SMBus interface. It measures the
voltage across

iio: adc: add MAX40080 current-sense amplifier driver

The MAX40080 is a bidirectional current-sense amplifier with an
integrated 12-bit ADC and an I2C/SMBus interface. It measures the
voltage across an external shunt resistor and the input bus voltage,
storing the results in an internal FIFO.

Add a direct-mode IIO driver exposing the current and voltage channels
with raw, scale and oversampling ratio attributes, a configurable
oversampling (digital averaging) ratio, and PEC-protected register
access. The current scale is derived from the shunt resistor value
described in the device tree.

The driver operates in single-measurement mode: each raw read triggers
an on-demand conversion via SMBus Quick Command and returns a matched
current/voltage pair. This avoids the latency and complexity of the
continuous FIFO mode while ensuring each read reflects the current
state. The two selectable current-sense ranges are exposed through
scale/scale_available.

Continuous FIFO buffering, threshold events and the alert interrupt are
intentionally left out of this initial submission and may be added
later.

Co-developed-by: Ciprian Hegbeli <ciprian.hegbeli@analog.com>
Signed-off-by: Ciprian Hegbeli <ciprian.hegbeli@analog.com>
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Reviewed-by: Siratul Islam <siratul.islam@linux.dev>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Jonathan Cameron <jonathan.cameron@oss.qualcomm.com>

show more ...


# 4a85662a 24-Aug-2026 Kyle Hsieh <kylehsieh1995@gmail.com>

iio: adc: ti-ads112c04: Add support for TI ADS112C04

Add IIO driver support for the Texas Instruments ADS112C04 (16-bit)
delta-sigma ADCs.

The driver implements:
- Single-shot conversions using the

iio: adc: ti-ads112c04: Add support for TI ADS112C04

Add IIO driver support for the Texas Instruments ADS112C04 (16-bit)
delta-sigma ADCs.

The driver implements:
- Single-shot conversions using the IIO raw read interface.
- Dynamic parsing of single-ended and differential channels from
device tree child nodes.
- Hardware interrupt support via the DRDY pin, falling back to
software polling if no IRQ is provided.
- Per-channel reference source selection (internal 2.048V, external
REFP/REFN, or AVDD) via the reference-sources device tree property.
refn-supply is not yet supported.
- Hardware reset via the reset controller framework, falling back to
the RESET command when no reset controller is present.

Signed-off-by: Kyle Hsieh <kylehsieh1995@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Jonathan Cameron <jonathan.cameron@oss.qualcomm.com>

show more ...


# 02f4bd27 10-Aug-2026 Petar Stepanovic <pstepanovic@axiado.com>

iio: adc: add Axiado SARADC driver

Add support for the SARADC controller found on Axiado AX3000 and
AX3005 SoCs.

The driver supports single-shot voltage reads through the IIO
subsystem. The number

iio: adc: add Axiado SARADC driver

Add support for the SARADC controller found on Axiado AX3000 and
AX3005 SoCs.

The driver supports single-shot voltage reads through the IIO
subsystem. The number of available input channels is selected from
the SoC match data, allowing AX3000 and AX3005 variants to use the
same driver.

Signed-off-by: Petar Stepanovic <pstepanovic@axiado.com>
Reviewed-by: Joshua Crofts <joshua.crofts1@gmail.com>
Signed-off-by: Jonathan Cameron <jonathan.cameron@oss.qualcomm.com>

show more ...


# 469eafdc 27-Jul-2026 Marcelo Schmitt <marcelo.schmitt@analog.com>

iio: adc: ltc2378: Add support for LTC2378-20 and similar ADCs

Support for LTC2378-20 and similar analog-to-digital converters.

Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Reviewed-b

iio: adc: ltc2378: Add support for LTC2378-20 and similar ADCs

Support for LTC2378-20 and similar analog-to-digital converters.

Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Marcelo Schmitt <marcelo.schmitt@analog.com>
Signed-off-by: Jonathan Cameron <jonathan.cameron@oss.qualcomm.com>

show more ...


# b7fa84f6 15-Jul-2026 David Lechner (TI) <dlechner@baylibre.com>

iio: adc: add ti-ads112c14 driver

Add a new driver for the TI ADS112C14/ADS122C14 ADC chips.

This first step is adding a very basic driver that only supports power
on/reset and reading the system m

iio: adc: add ti-ads112c14 driver

Add a new driver for the TI ADS112C14/ADS122C14 ADC chips.

This first step is adding a very basic driver that only supports power
on/reset and reading the system monitor channels.

ADS112C14_SYS_MON_CHANNEL_SHORT is the last channel rather than being in
logical order by address to keep the voltage channels together and in
case we find we need to add variants of this channel with different
voltage reference later.

Signed-off-by: David Lechner (TI) <dlechner@baylibre.com>
Signed-off-by: Jonathan Cameron <jonathan.cameron@oss.qualcomm.com>

show more ...


# 2dd8c526 24-Jun-2026 Salih Erim <salih.erim@amd.com>

iio: adc: versal-sysmon: add I2C driver

Add an I2C transport driver for the Versal SysMon block. The SysMon
provides an I2C slave interface that allows an external master to
read voltage and tempera

iio: adc: versal-sysmon: add I2C driver

Add an I2C transport driver for the Versal SysMon block. The SysMon
provides an I2C slave interface that allows an external master to
read voltage and temperature measurements through the same register
map used by the MMIO path.

The I2C command frame is an 8-byte structure containing a 4-byte data
payload, a 2-byte register offset, and a 1-byte instruction field.
Read operations send the frame with a read instruction, then receive
a 4-byte response containing the register value.

Events are not supported on the I2C path because there is no
interrupt line and the I2C regmap backend cannot be called from
atomic context.

Co-developed-by: Conall O'Griofa <conall.ogriofa@amd.com>
Signed-off-by: Conall O'Griofa <conall.ogriofa@amd.com>
Signed-off-by: Salih Erim <salih.erim@amd.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

show more ...


# 50bf4fd8 24-Jun-2026 Salih Erim <salih.erim@amd.com>

iio: adc: add Versal SysMon driver

Add the core driver and MMIO platform driver for the AMD/Xilinx Versal
System Monitor (SysMon) block.

The SysMon block resides in the platform management controll

iio: adc: add Versal SysMon driver

Add the core driver and MMIO platform driver for the AMD/Xilinx Versal
System Monitor (SysMon) block.

The SysMon block resides in the platform management controller (PMC) and
provides on-chip voltage and temperature monitoring through a 10-bit,
200 kSPS ADC. It can monitor up to 160 voltage channels and 64
temperature satellites distributed across the SoC, with a consistent
sample rate of 8 kSPS per channel regardless of how many channels are
enabled.

The hardware also provides four aggregate temperature registers that
are always present regardless of the device tree configuration: the
current max and min across all active satellites, and the peak and
trough values recorded since the last hardware reset.

The driver is split into two compilation units:
- versal-sysmon-core: Channel parsing, IIO registration, read_raw
- versal-sysmon: MMIO platform driver with custom regmap accessors

Voltage results are stored in a 19-bit modified floating-point format
and converted to millivolts. Temperature results are stored in Q8.7
signed fixed-point Celsius format and converted to millicelsius.

The MMIO regmap backend uses a custom reg_write accessor that
automatically unlocks the NPI (NoC programming interface) lock
register before each write, as required by the hardware. The regmap
is configured with fast_io since the underlying MMIO accessors are
safe to call from atomic context.

Co-developed-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Salih Erim <salih.erim@amd.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

show more ...


# d6c384c3 23-Jun-2026 Roman Vivchar <rva333@protonmail.com>

iio: adc: mt6323-auxadc: add mt6323 PMIC AUXADC driver

The mt6323 AUXADC is a 15-bit ADC used for system monitoring. This driver
provides support for reading various channels including battery and
c

iio: adc: mt6323-auxadc: add mt6323 PMIC AUXADC driver

The mt6323 AUXADC is a 15-bit ADC used for system monitoring. This driver
provides support for reading various channels including battery and
charger voltages, battery and chip temperature, current sensing and
accessory detection.

Add a driver for the AUXADC found in the MediaTek mt6323 PMIC.

Tested-by: Ben Grisdale <bengris32@protonmail.ch> # Amazon Echo Dot (2nd Generation)
Signed-off-by: Roman Vivchar <rva333@protonmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

show more ...


# 40850443 29-May-2026 Radu Sabau <radu.sabau@analog.com>

iio: adc: ad4691: add initial driver for AD4691 family

Add support for the Analog Devices AD4691 family of high-speed,
low-power multichannel SAR ADCs: AD4691 (16-ch, 500 kSPS),
AD4692 (16-ch, 1 MSP

iio: adc: ad4691: add initial driver for AD4691 family

Add support for the Analog Devices AD4691 family of high-speed,
low-power multichannel SAR ADCs: AD4691 (16-ch, 500 kSPS),
AD4692 (16-ch, 1 MSPS), AD4693 (8-ch, 500 kSPS) and
AD4694 (8-ch, 1 MSPS).

The driver implements a custom regmap layer over raw SPI to handle the
device's mixed 1/2/3/4-byte register widths and uses the standard IIO
read_raw/write_raw interface for single-channel reads.

The chip idles in Autonomous Mode so that single-shot read_raw can use
the internal oscillator without disturbing the hardware configuration.

Three voltage supply domains are managed: avdd (required), vio, and a
reference supply on either the REF pin (ref-supply, external buffer)
or the REFIN pin (refin-supply, uses the on-chip reference buffer;
REFBUF_EN is set accordingly). Hardware reset is performed by asserting
then deasserting the reset-gpios GPIO line (tRESETL minimum pulse width
is 10 ns, satisfied by function-call overhead); the driver then waits
300 µs for the chip to complete its internal reset sequence. A software
reset via SPI_CONFIG_A is used as fallback when no reset GPIO is
provided.

Accumulator channel masking for single-shot reads uses ACC_MASK_REG via
an ADDR_DESCENDING SPI write, which covers both mask bytes in a single
16-bit transfer.

Reviewed-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Radu Sabau <radu.sabau@analog.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

show more ...


# baff4517 30-Jan-2026 Jishnu Prakash <jishnu.prakash@oss.qualcomm.com>

iio: adc: Add support for QCOM PMIC5 Gen3 ADC

The ADC architecture on PMIC5 Gen3 is similar to that on PMIC5 Gen2,
with all SW communication to ADC going through PMK8550 which
communicates with othe

iio: adc: Add support for QCOM PMIC5 Gen3 ADC

The ADC architecture on PMIC5 Gen3 is similar to that on PMIC5 Gen2,
with all SW communication to ADC going through PMK8550 which
communicates with other PMICs through PBS.

One major difference is that the register interface used here is that
of an SDAM (Shared Direct Access Memory) peripheral present on PMK8550.
There may be more than one SDAM used for ADC5 Gen3 and each has eight
channels, which may be used for either immediate reads (same functionality
as previous PMIC5 and PMIC5 Gen2 ADC peripherals) or recurring measurements
(same as ADC_TM functionality).

By convention, we reserve the first channel of the first SDAM for all
immediate reads and use the remaining channels across all SDAMs for
ADC_TM monitoring functionality.

Add support for PMIC5 Gen3 ADC driver for immediate read functionality.
ADC_TM is implemented as an auxiliary thermal driver under this ADC
driver.

Signed-off-by: Jishnu Prakash <jishnu.prakash@oss.qualcomm.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

show more ...


# e0bc6d7e 07-Jan-2026 Marcelo Schmitt <marcelo.schmitt@analog.com>

iio: adc: Initial support for AD4134

AD4134 is a 24-bit, 4-channel, simultaneous sampling, precision
analog-to-digital converter (ADC). The device can be managed through SPI or
direct control of pin

iio: adc: Initial support for AD4134

AD4134 is a 24-bit, 4-channel, simultaneous sampling, precision
analog-to-digital converter (ADC). The device can be managed through SPI or
direct control of pin logical levels (pin control mode). The AD4134 design
also features a dedicated bus for ADC sample data output. Though, this
initial driver for AD4134 only supports usual SPI connections.

Add basic support for AD4134 that enables single-shot ADC sample read.

Signed-off-by: Marcelo Schmitt <marcelo.schmitt@analog.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

show more ...


# d5284402 17-Dec-2025 Jorge Marques <jorge.marques@analog.com>

iio: adc: Add support for ad4062

The AD4060/AD4062 are versatile, 16-bit/12-bit, successive approximation
register (SAR) analog-to-digital converter (ADC) with low-power and
threshold monitoring mod

iio: adc: Add support for ad4062

The AD4060/AD4062 are versatile, 16-bit/12-bit, successive approximation
register (SAR) analog-to-digital converter (ADC) with low-power and
threshold monitoring modes.

Signed-off-by: Jorge Marques <jorge.marques@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

show more ...


# bf0bba48 12-Dec-2025 Kurt Borja <kuurtb@gmail.com>

iio: adc: Add ti-ads1018 driver

Add ti-ads1018 driver for Texas Instruments ADS1018 and ADS1118 SPI
analog-to-digital converters.

This chips' MOSI pin is shared with a data-ready interrupt. Definin

iio: adc: Add ti-ads1018 driver

Add ti-ads1018 driver for Texas Instruments ADS1018 and ADS1118 SPI
analog-to-digital converters.

This chips' MOSI pin is shared with a data-ready interrupt. Defining
this interrupt in devicetree is optional, therefore we only create an
IIO trigger if one is found.

Handling this interrupt requires some considerations. When enabling the
trigger the CS line is tied low (active), thus we need to hold
spi_bus_lock() too, to avoid state corruption. This is done inside the
set_trigger_state() callback, to let users use other triggers without
wasting a bus lock.

Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Kurt Borja <kuurtb@gmail.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

show more ...


# 4434072a 08-Dec-2025 Daniel Lezcano <daniel.lezcano@linaro.org>

iio: adc: Add the NXP SAR ADC support for the s32g2/3 platforms

The NXP S32G2 and S32G3 platforms integrate a successive approximation
register (SAR) ADC. Two instances are available, each providing

iio: adc: Add the NXP SAR ADC support for the s32g2/3 platforms

The NXP S32G2 and S32G3 platforms integrate a successive approximation
register (SAR) ADC. Two instances are available, each providing 8
multiplexed input channels with 12-bit resolution. The conversion rate
is up to 1 Msps depending on the configuration and sampling window.

The SAR ADC supports raw, buffer, and trigger modes. It can operate
in both single-shot and continuous conversion modes, with optional
hardware triggering through the cross-trigger unit (CTU) or external
events. An internal prescaler allows adjusting the sampling clock,
while per-channel programmable sampling times provide fine-grained
trade-offs between accuracy and latency. Automatic calibration is
performed at probe time to minimize offset and gain errors.

All modes have been validated on the S32G274-RDB2 platform using an
externally generated square wave captured by the ADC. Tests covered
buffered streaming via IIO, trigger synchronization, and accuracy
verification against a precision laboratory signal source.

One potential scenario, not detected during testing, is that in some
corner cases the DMA may already have been armed for the next
transfer, which can lead dmaengine_tx_status() to return an incorrect
residue. The callback_result() operation—intended to supply the
residue directly and eliminate the need to call
dmaengine_tx_status()—also does not work. Attempting to use
dmaengine_pause() and dmaengine_resume() to prevent the residue from
being updated does not work either.

This potential scenario should apply to any driver using cyclic DMA.
However, no current driver actually handles this case, and they all rely
on the same acquisition routine (e.g., the STM32 implementation).
The NXP SAR acquisition routine has been used in production for several
years, which is a good indication of its robustness.

As the IIO is implementing the cyclic DMA support API, it is not worth
to do more spins to the current routine as it will go away when the
new API will be available.

The driver is derived from the BSP implementation and has been partly
rewritten to comply with upstream requirements. For this reason, all
contributors to the original code are listed as co-developers.

Originally-by: Stefan-Gabriel Mirea <stefan-gabriel.mirea@nxp.com>
Co-developed-by: Alexandru-Catalin Ionita <alexandru-catalin.ionita@nxp.com>
Signed-off-by: Alexandru-Catalin Ionita <alexandru-catalin.ionita@nxp.com>
Co-developed-by: Ciprian Costea <ciprianmarian.costea@nxp.com>
Signed-off-by: Ciprian Costea <ciprianmarian.costea@nxp.com>
Co-developed-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

show more ...


# 4aa91223 18-Nov-2025 David Jander <david@protonic.nl>

iio: adc: Add TI ADS131M0x ADC driver

Add a new IIO ADC driver for Texas Instruments ADS131M0x devices
(ADS131M02/03/04/06/08). These are 24-bit, up to 64 kSPS, simultaneous-
sampling delta-sigma AD

iio: adc: Add TI ADS131M0x ADC driver

Add a new IIO ADC driver for Texas Instruments ADS131M0x devices
(ADS131M02/03/04/06/08). These are 24-bit, up to 64 kSPS, simultaneous-
sampling delta-sigma ADCs accessed via SPI.

Highlights:
- Supports 2/3/4/6/8-channel variants with per-channel RAW and SCALE.
- Implements device-required full-duplex fixed-frame transfers.
- Handles both input and output CRC

Note: Despite the almost identical name, this hardware is not
compatible with the ADS131E0x series handled by
drivers/iio/adc/ti-ads131e08.c.

Signed-off-by: David Jander <david@protonic.nl>
Co-developed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

show more ...


# 2387a7d6 03-Nov-2025 Herve Codina (Schneider Electric) <herve.codina@bootlin.com>

iio: adc: Add support for the Renesas RZ/N1 ADC

The Renesas RZ/N1 ADC controller is the ADC controller available in the
Renesas RZ/N1 SoCs family. It can use up to two internal ADC cores (ADC1
and A

iio: adc: Add support for the Renesas RZ/N1 ADC

The Renesas RZ/N1 ADC controller is the ADC controller available in the
Renesas RZ/N1 SoCs family. It can use up to two internal ADC cores (ADC1
and ADC2) those internal cores are not directly accessed but are handled
through ADC controller virtual channels.

Signed-off-by: Herve Codina (Schneider Electric) <herve.codina@bootlin.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

show more ...


# 59795109 15-Oct-2025 Marilene Andrade Garcia <marilene.agarcia@gmail.com>

iio: adc: max14001: New driver

The MAX14001/MAX14002 is configurable, isolated 10-bit ADCs for multi-range
binary inputs. In addition to ADC readings, the MAX14001/MAX14002 offers
more features, lik

iio: adc: max14001: New driver

The MAX14001/MAX14002 is configurable, isolated 10-bit ADCs for multi-range
binary inputs. In addition to ADC readings, the MAX14001/MAX14002 offers
more features, like a binary comparator, a filtered reading that can
provide the average of the last 2, 4, or 8 ADC readings, and an inrush
comparator that triggers the inrush current. There is also a fault feature
that can diagnose seven possible fault conditions. And an option to select
an external or internal ADC voltage reference.

MAX14001/MAX14002 features implemented so far:
- Raw ADC reading.
- MV fault disable.
- Selection of external or internal ADC voltage reference, depending on
whether it is declared in the device tree.

Co-developed-by: Kim Seer Paller <kimseer.paller@analog.com>
Signed-off-by: Kim Seer Paller <kimseer.paller@analog.com>
Signed-off-by: Marilene Andrade Garcia <marilene.agarcia@gmail.com>
Tested-by: Marcelo Schmitt <marcelo.schmitt1@gmail.com>
Reviewed-by: Marcelo Schmitt <marcelo.schmitt1@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

show more ...


# fc3b97dd 05-Oct-2025 Cosmin Tanislav <cosmin-gabriel.tanislav.xa@renesas.com>

iio: adc: add RZ/T2H / RZ/N2H ADC driver

Add support for the A/D 12-Bit successive approximation converters found
in the Renesas RZ/T2H (R9A09G077) and RZ/N2H (R9A09G087) SoCs.

RZ/T2H has two ADCs

iio: adc: add RZ/T2H / RZ/N2H ADC driver

Add support for the A/D 12-Bit successive approximation converters found
in the Renesas RZ/T2H (R9A09G077) and RZ/N2H (R9A09G087) SoCs.

RZ/T2H has two ADCs with 4 channels and one with 6.
RZ/N2H has two ADCs with 4 channels and one with 15.

Conversions can be performed in single or continuous mode. Result of the
conversion is stored in a 16-bit data register corresponding to each
channel.

The conversions can be started by a software trigger, a synchronous
trigger (from MTU or from ELC) or an asynchronous external trigger (from
ADTRGn# pin).

Only single mode with software trigger is supported for now.

Signed-off-by: Cosmin Tanislav <cosmin-gabriel.tanislav.xa@renesas.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

show more ...


# edf2fc7b 15-Sep-2025 Matti Vaittinen <mazziesaccount@gmail.com>

iio: adc: Support ROHM BD79112 ADC/GPIO

The ROHM BD79112 is an ADC/GPIO with 32 channels. The channel inputs can
be used as ADC or GPIO. Using the GPIOs as IRQ sources isn't supported.

The ADC is 1

iio: adc: Support ROHM BD79112 ADC/GPIO

The ROHM BD79112 is an ADC/GPIO with 32 channels. The channel inputs can
be used as ADC or GPIO. Using the GPIOs as IRQ sources isn't supported.

The ADC is 12-bit, supporting input voltages up to 5.7V, and separate I/O
voltage supply. Maximum SPI clock rate is 20 MHz (10 MHz with
daisy-chain configuration) and maximum sampling rate is 1MSPS.

The IC does also support CRC but it is not implemented in the driver.

Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

show more ...


# 3422b4bc 11-Sep-2025 Duje Mihanović <duje@dujemihanovic.xyz>

iio: adc: Add driver for Marvell 88PM886 PMIC ADC

Marvell's 88PM886 PMIC has a so-called General Purpose ADC used for
monitoring various system voltages and temperatures. Add the relevant
register d

iio: adc: Add driver for Marvell 88PM886 PMIC ADC

Marvell's 88PM886 PMIC has a so-called General Purpose ADC used for
monitoring various system voltages and temperatures. Add the relevant
register definitions to the MFD header and a driver for the ADC.

Acked-by: Karel Balej <balejk@matfyz.cz> # for the PMIC
Signed-off-by: Duje Mihanović <duje@dujemihanovic.xyz>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

show more ...


# 81de7b46 08-Sep-2025 Antoniu Miclaus <antoniu.miclaus@analog.com>

iio: adc: add ade9000 support

Add driver support for the ade9000. highly accurate,
fully integrated, multiphase energy and power quality
monitoring device.

Signed-off-by: Antoniu Miclaus <antoniu.m

iio: adc: add ade9000 support

Add driver support for the ade9000. highly accurate,
fully integrated, multiphase energy and power quality
monitoring device.

Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

show more ...


# 28e4b859 31-Aug-2025 Hans de Goede <hansg@kernel.org>

iio: adc: Add Intel Dollar Cove TI PMIC ADC driver

Intel has 2 completely different "Dollar Cove" PMICs for its Bay Trail /
Cherry Trail SoCs. One is made by X-Powers and is called the AXP288.
The A

iio: adc: Add Intel Dollar Cove TI PMIC ADC driver

Intel has 2 completely different "Dollar Cove" PMICs for its Bay Trail /
Cherry Trail SoCs. One is made by X-Powers and is called the AXP288.
The AXP288's GPADC is already supported by the X-Powers AXP288 ADC driver.

The other "Dollar Cove" PMIC is made by TI and does not have any clear TI
denomination, its MFD driver calls it the "Intel Dollar Cove TI PMIC".

Add a driver for the Intel Dollar Cove TI PMIC's general purpose ADC,
binding to the "chtdc_ti_adc" MFD cell of the MFD driver.

The "cht" in the cell name comes from Cherry Trail, but it turns out that
just like the AXP288 the Intel Dollar Cove TI PMIC is also used with both
Intel Bay Trail and Intel Cherry Trail SoCs, so this new ADC driver does
not include the cht part in its name.

This is loosely based on kernel/drivers/iio/adc/iio_dc_ti_gpadc.c
from the Acer A1-840 Android kernel source-code archive named:
"App. Guide_Acer_20151221_A_A.zip"
which is distributed by Acer from the Acer A1-840 support page:
https://www.acer.com/us-en/support/product-support/A1-840/downloads

Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Hans de Goede <hansg@kernel.org>
Link: https://patch.msgid.link/20250831104825.15097-7-hansg@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

show more ...


# 5731f2a0 07-Jul-2025 Ana-Maria Cusco <ana-maria.cusco@analog.com>

iio: adc: Add basic support for AD4170-4

The AD4170-4 is a multichannel, low noise, 24-bit precision sigma-delta
analog to digital converter. The AD4170-4 design offers a flexible data
acquisition s

iio: adc: Add basic support for AD4170-4

The AD4170-4 is a multichannel, low noise, 24-bit precision sigma-delta
analog to digital converter. The AD4170-4 design offers a flexible data
acquisition solution with crosspoint multiplexed analog inputs,
configurable ADC voltage reference inputs, ultra-low noise integrated PGA,
digital filtering, wide range of configurable output data rates, internal
oscillator and temperature sensor, four GPIOs, and integrated features for
interfacing with load cell weigh scales, RTD, and thermocouple sensors.

Add basic support for the AD4170-4 ADC with the following features:
- Single-shot read.
- Analog front end PGA configuration.
- Differential and pseudo-differential input configuration.

Signed-off-by: Ana-Maria Cusco <ana-maria.cusco@analog.com>
Co-developed-by: Marcelo Schmitt <marcelo.schmitt@analog.com>
Signed-off-by: Marcelo Schmitt <marcelo.schmitt@analog.com>
Link: https://patch.msgid.link/ce3fd150bd63a2aed6eb6fe59aad6d60c0f9fb67.1751895245.git.marcelo.schmitt@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

show more ...


# 6a533f56 05-Jun-2025 Pop Ioan Daniel <pop.ioan-daniel@analog.com>

iio: adc: ad7405: add ad7405 driver

Add support for the AD7405/ADUM770x, a high performance isolated ADC,
1-channel, 16-bit with a second-order Σ-Δ modulator that converts an
analog input signal int

iio: adc: ad7405: add ad7405 driver

Add support for the AD7405/ADUM770x, a high performance isolated ADC,
1-channel, 16-bit with a second-order Σ-Δ modulator that converts an
analog input signal into a high speed, single-bit data stream.

Signed-off-by: Pop Ioan Daniel <pop.ioan-daniel@analog.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250605150948.3091827-6-pop.ioan-daniel@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

show more ...


12345678