ata: libata: Document when host->eh_mutex should be held

Annotate the following functions with __must_hold(&host->eh_mutex):
* All ata_port_operations.error_handler() implementations.
* ata_eh_res

ata: libata: Document when host->eh_mutex should be held

Annotate the following functions with __must_hold(&host->eh_mutex):
* All ata_port_operations.error_handler() implementations.
* ata_eh_reset() and ata_eh_recover() because these functions call
ata_eh_release() and ata_eh_acquire().
* All callers of ata_eh_reset() and ata_eh_recover().

Enable Clang's context analysis. This will cause the build to fail if
e.g. a locking bug would be introduced in an error path. This patch
should not affect the generated assembler code.

Signed-off-by: Bart Van Assche <bvanassche@acm.org>
[cassel: drop note about clang 23 from commit log]
Signed-off-by: Niklas Cassel <cassel@kernel.org>

show more ...

Merge tag 'ata-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata

Pull ATA updates from Damien Le Moal:

- Small cleanup of the pata_octeon driver to drop a useless platform

Merge tag 'ata-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata

Pull ATA updates from Damien Le Moal:

- Small cleanup of the pata_octeon driver to drop a useless platform
callback (Uwe)

- Simplify ata_scsi_cmd_error_handler() code using the fact that
ap->ops->error_handler is NULL most of the time (Wenchao)

- Several patches improving libata error handling. This is in
preparation for supporting the command duration limits (CDL) feature.
The changes allow handling corner cases of ATA NCQ errors which do
not happen with regular drives but will be triggered with CDL drives
(Niklas)

- Simplify the qc_fill_rtf operation (me)

- Improve SCSI command translation for REPORT_SUPPORTED_OPERATION_CODES
command (me)

- Cleanup of libata FUA handling.

This falls short of enabling FUA for ATA drives that support it by
default as there were concerns that old drives would break. The
series however fixes several issues with the FUA support to ensure
that FUA is reported as being supported only for drives that can
handle all possible write cases (NCQ and non-NCQ). A check in the
block layer is also added to ensure that we never see read FUA
commands (current behavior) (me)

- Several patches to move the old PARIDE (parallel port IDE) driver to
libata as pata_parport. Given that this driver also needs protocol
modules, the driver code resides in its own pata_parport directoy
under drivers/ata (Ondrej)

* tag 'ata-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata:
ata: pata_parport: Fix ida_alloc return value error check
drivers/block: Move PARIDE protocol modules to drivers/ata/pata_parport
drivers/block: Remove PARIDE core and high-level protocols
ata: pata_parport: add driver (PARIDE replacement)
ata: libata: exclude FUA support for known buggy drives
ata: libata: Fix FUA handling in ata_build_rw_tf()
ata: libata: cleanup fua support detection
ata: libata: Rename and cleanup ata_rwcmd_protocol()
ata: libata: Introduce ata_ncq_supported()
block: add a sanity check for non-write flush/fua bios
ata: libata-scsi: improve ata_scsiop_maint_in()
ata: libata-scsi: do not overwrite SCSI ML and status bytes
ata: libata: move NCQ related ATA_DFLAGs
ata: libata: respect successfully completed commands during errors
ata: libata: read the shared status for successful NCQ commands once
ata: libata: simplify qc_fill_rtf port operation interface
ata: scsi: rename flag ATA_QCFLAG_FAILED to ATA_QCFLAG_EH
ata: libata-eh: Cleanup ata_scsi_cmd_error_handler()
ata: octeon: Drop empty platform remove function

show more ...

drivers/block: Move PARIDE protocol modules to drivers/ata/pata_parport

Move PARIDE protocol modules out of drivers/block into
drivers/ata/pata_parport and update the CONFIG_ symbol names to
PATA_PA

drivers/block: Move PARIDE protocol modules to drivers/ata/pata_parport

Move PARIDE protocol modules out of drivers/block into
drivers/ata/pata_parport and update the CONFIG_ symbol names to
PATA_PARPORT.

[Damien]
The pata_parport driver file itsef is also moved together with the
protocol modules in drivers/ata/pata_parport.

Signed-off-by: Ondrej Zary <linux@zary.sk>
Acked-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>

show more ...

ata: pata_parport: add driver (PARIDE replacement)

The pata_parport is a libata-based replacement of the old PARIDE
subsystem - driver for parallel port IDE devices.
It uses the original paride low-

ata: pata_parport: add driver (PARIDE replacement)

The pata_parport is a libata-based replacement of the old PARIDE
subsystem - driver for parallel port IDE devices.
It uses the original paride low-level protocol drivers but does not
need the high-level drivers (pd, pcd, pf, pt, pg). The IDE devices
behind parallel port adapters are handled by the ATA layer.

This will allow paride and its high-level drivers to be removed.

Unfortunately, libata drivers cannot sleep so pata_parport claims
parport before activating the ata host and keeps it claimed (and
protocol connected) until the ata host is removed. This means that
no devices can be chained (neither other pata_parport devices nor
a printer).

paride and pata_parport are mutually exclusive because the compiled
protocol drivers are incompatible.

Tested with:
- Imation SuperDisk LS-120 and HP C4381A (EPAT)
- Freecom Parallel CD (FRPW)
- Toshiba Mobile CD-RW 2793008 w/Freecom Parallel Cable rev.903 (FRIQ)
- Backpack CD-RW 222011 and CD-RW 19350 (BPCK6)

The following bugs in low-level protocol drivers were found and will
be fixed later:

Note: EPP-32 mode is buggy in EPAT - and also in all other protocol
drivers - they don't handle non-multiple-of-4 block transfers
correctly. This causes problems with LS-120 drive.
There is also another bug in EPAT: EPP modes don't work unless a 4-bit
or 8-bit mode is used first (probably some initialization missing?).
Once the device is initialized, EPP works until power cycle.

So after device power on, you have to:
echo "parport0 epat 0" >/sys/bus/pata_parport/new_device
echo pata_parport.0 >/sys/bus/pata_parport/delete_device
echo "parport0 epat 4" >/sys/bus/pata_parport/new_device
(autoprobe will initialize correctly as it tries the slowest modes
first but you'll get the broken EPP-32 mode)

Note: EPP modes are buggy in FRPW, only modes 0 and 1 work.

Signed-off-by: Ondrej Zary <linux@zary.sk>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Acked-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>

show more ...

ata: remove palmld pata driver

The PXA palmld machine was removed, so the pata driver is no
longer used and can be removed. There is a chance that some of
this code might be useful for turning some

ata: remove palmld pata driver

The PXA palmld machine was removed, so the pata driver is no
longer used and can be removed. There is a chance that some of
this code might be useful for turning some of the other PXA
PCMCIA host drivers into PATA drivers, but it's clear that
it would not work unmodified, and it seems unlikely that
someone would do this work.

Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-ide@vger.kernel.org
Acked-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

show more ...

pata: remove samsung_cf driver

This device was only used by the smdk6410 board file that is now
gone, so the driver can be removed as well.

Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Acked-by

pata: remove samsung_cf driver

This device was only used by the smdk6410 board file that is now
gone, so the driver can be removed as well.

Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Acked-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

show more ...

ata: remove palmchip pata_bk3710 driver

This device was used only on the davinci dm644x platform that
is now gone, and no references to the device remain in the
kernel.

Signed-off-by: Arnd Bergmann

ata: remove palmchip pata_bk3710 driver

This device was used only on the davinci dm644x platform that
is now gone, and no references to the device remain in the
kernel.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Marc Zyngier <maz@kernel.org>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>

show more ...

ata: ahci: Add DWC AHCI SATA controller support

Synopsys AHCI SATA controller can work pretty under with the generic
AHCI-platform driver control. But there are vendor-specific peculiarities
which c

ata: ahci: Add DWC AHCI SATA controller support

Synopsys AHCI SATA controller can work pretty under with the generic
AHCI-platform driver control. But there are vendor-specific peculiarities
which can tune the device performance up and which may need to be fixed up
for proper device functioning. In addition some DWC AHCI-based controllers
may require small platform-specific fixups, so adding them in the generic
AHCI driver would have ruined the code simplicity. Shortly speaking in
order to keep the generic AHCI-platform code clean and have DWC AHCI
SATA-specific features supported we suggest to add a dedicated DWC AHCI
SATA device driver. Aside with the standard AHCI-platform resources
getting, enabling/disabling and the controller registration the new driver
performs the next actions.

First of all there is a way to verify whether the HBA/ports capabilities
activated in OF are correct. Almost all features availability is reflected
in the vendor-specific parameters registers. So the DWC AHCI driver does
the capabilities sanity check based on the corresponding fields state.

Secondly if either the Command Completion Coalescing or the Device Sleep
feature is enabled the DWC AHCI-specific internal 1ms timer must be fixed
in accordance with the application clock signal frequency. In particular
the timer value must be set to be Fapp * 1000. Normally the SoC designers
pre-configure the TIMER1MS register to contain a correct value by default.
But the platforms can support the application clock rate change. If that
happens the 1ms timer value must be accordingly updated otherwise the
dependent features won't work as expected. In the DWC AHCI driver we
suggest to rely on the "aclk" reference clock rate to set the timer
interval up. That clock source is supposed to be the AHCI SATA application
clock in accordance with the DT bindings.

Finally DWC AHCI SATA controller AXI/AHB bus DMA-engine can be tuned up to
transfer up to 1024 * FIFO words at a time by setting the Tx/Rx
transaction size in the DMA control register. The maximum value depends on
the DMA data bus and AXI/AHB bus maximum burst length. In most of the
cases it's better to set the maximum possible value to reach the best AHCI
SATA controller performance. But sometimes in order to improve the system
interconnect responsiveness, transferring in smaller data chunks may be
more preferable. For such cases and for the case when the default value
doesn't provide the best DMA bus performance we suggest to use the new
HBA-port specific DT-properties "snps,{tx,rx}-ts-max" to tune the DMA
transactions size up.

After all the settings denoted above are handled the DWC AHCI SATA driver
proceeds further with the standard AHCI-platform host initializations.

Note since DWC AHCI controller is now have a dedicated driver we can
discard the corresponding compatible string from the ahci-platform.c
module. The same concerns "snps,spear-ahci" compatible string, which is
also based on the DWC AHCI IP-core.

Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>

show more ...

ata: start separating SATA specific code from libata-core.c

Start separating SATA specific code from libata-core.c:

* move following functions to libata-sata.c:
- ata_tf_to_fis()
- ata_tf_from_

ata: start separating SATA specific code from libata-core.c

Start separating SATA specific code from libata-core.c:

* move following functions to libata-sata.c:
- ata_tf_to_fis()
- ata_tf_from_fis()
- sata_link_scr_lpm()
- ata_slave_link_init()
- sata_lpm_ignore_phy_events()

* group above functions together in <linux/libata.h>

* include libata-sata.c in the build when CONFIG_SATA_HOST=y

Code size savings on m68k arch using (modified) atari_defconfig:

text data bss dec hex filename
before:
37582 572 40 38194 9532 drivers/ata/libata-core.o
after:
36762 572 40 37374 91fe drivers/ata/libata-core.o

Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

show more ...

ata: separate PATA timings code from libata-core.c

Separate PATA timings code from libata-core.c:

* add PATA_TIMINGS config option and make corresponding PATA
host drivers (and ATA ACPI code) sel

ata: separate PATA timings code from libata-core.c

Separate PATA timings code from libata-core.c:

* add PATA_TIMINGS config option and make corresponding PATA
host drivers (and ATA ACPI code) select it

* move following PATA timings code to libata-pata-timings.c:
- ata_timing_quantize()
- ata_timing_merge()
- ata_timing_find_mode()
- ata_timing_compute()

* group above functions together in <linux/libata.h>

* include libata-pata-timings.c in the build when PATA_TIMINGS
config option is enabled

* cover ata_timing_cycle2mode() with CONFIG_ATA_ACPI ifdef (it
depends on code from libata-core.c and libata-pata-timings.c
while its only user is ATA ACPI)

Code size savings on m68k arch using (modified) atari_defconfig:

text data bss dec hex filename
before:
39688 573 40 40301 9d6d drivers/ata/libata-core.o
after:
37820 572 40 38432 9620 drivers/ata/libata-core.o

Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

show more ...

ata: add Buddha PATA controller driver

Add Buddha PATA controller driver. It enables libata support for
the Buddha, Catweasel and X-Surf expansion boards on the Zorro
expansion bus.

Module removal

ata: add Buddha PATA controller driver

Add Buddha PATA controller driver. It enables libata support for
the Buddha, Catweasel and X-Surf expansion boards on the Zorro
expansion bus.

Module removal is currently unsupported (the old IDE's buddha
driver also doesn't support it).

Tested-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Cc: Michael Schmitz <schmitzmic@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

show more ...

Merge branch 'for-4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata

Pull libata updates from Tejun Heo:
"Nothing too interesting.

The biggest change is refcnting fix for ata_host

Merge branch 'for-4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata

Pull libata updates from Tejun Heo:
"Nothing too interesting.

The biggest change is refcnting fix for ata_host - the bug is recent
and can only be triggered on controller hotplug, so very few are
hitting it.

There also are a number of trivial license / error message changes and
some hardware specific changes"

* 'for-4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: (23 commits)
ahci: imx: add the imx8qm ahci sata support
libata: ensure host is free'd on error exit paths
ata: ahci-platform: add reset control support
ahci: imx: fix the build warning
ata: add Amiga Gayle PATA controller driver
ahci: imx: add the imx6qp ahci sata support
ata: change Tegra124 to Tegra
ata: ahci_tegra: Add AHCI support for Tegra210
ata: ahci_tegra: disable DIPM
ata: ahci_tegra: disable devslp for Tegra124
ata: ahci_tegra: initialize regulators from soc struct
ata: ahci_tegra: Update initialization sequence
dt-bindings: Tegra210: add binding documentation
libata: add refcounting to ata_host
pata_bk3710: clarify license version and use SPDX header
pata_falcon: clarify license version and use SPDX header
pata_it821x: Delete an error message for a failed memory allocation in it821x_firmware_command()
pata_macio: Delete an error message for a failed memory allocation in two functions
pata_mpc52xx: Delete an error message for a failed memory allocation in mpc52xx_ata_probe()
sata_dwc_460ex: Delete an error message for a failed memory allocation in sata_dwc_port_start()
...

show more ...

ata: remove bf54x driver

The blackfin architecture is getting removed, so this driver
is obsolete as well.

Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

ata: add Amiga Gayle PATA controller driver

Add Amiga Gayle PATA controller driver. It enables libata support
for the on-board IDE interfaces on some Amiga models (A600, A1200,
A4000 and A4000T) and

ata: add Amiga Gayle PATA controller driver

Add Amiga Gayle PATA controller driver. It enables libata support
for the on-board IDE interfaces on some Amiga models (A600, A1200,
A4000 and A4000T) and also for IDE interfaces on the Zorro expansion
bus (M-Tech E-Matrix 530 expansion card).

Thanks to John Paul Adrian Glaubitz and Michael Schmitz for help
with testing the driver.

Tested-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Cc: Michael Schmitz <schmitzmic@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>

show more ...

ata: remove pata_at32

Since AVR32 was removed, pata_at32 is unselectable/uncompilable.
Remove this driver.

Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Tejun Heo <tj@ker

ata: remove pata_at32

Since AVR32 was removed, pata_at32 is unselectable/uncompilable.
Remove this driver.

Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>

show more ...

License cleanup: add SPDX GPL-2.0 license identifier to files with no license

Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine

License cleanup: add SPDX GPL-2.0 license identifier to files with no license

Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.

By default all files without license information are under the default
license of the kernel, which is GPL version 2.

Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.

This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.

How this work was done:

Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,

Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.

The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.

The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.

Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).

All documentation files were explicitly excluded.

The following heuristics were used to determine which SPDX license
identifiers to apply.

- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.

For non */uapi/* files that summary was:

SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139

and resulted in the first patch in this series.

If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:

SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930

and resulted in the second patch in this series.

- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:

SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1

and that resulted in the third patch in this series.

- when the two scanners agreed on the detected license(s), that became
the concluded license(s).

- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.

- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).

- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.

- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.

In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.

Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.

Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.

In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.

Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct

This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.

These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.

Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

ata: mediatek: add support for MediaTek SATA controller

This adds support the AHCI-compliant Serial ATA controller present
on MediaTek SoCs.

Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Acked-

ata: mediatek: add support for MediaTek SATA controller

This adds support the AHCI-compliant Serial ATA controller present
on MediaTek SoCs.

Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Tejun Heo <tj@kernel.org>

show more ...

ata: Add driver for Faraday Technology FTIDE010

This adds a driver for the Faraday Technology FTIDE010
PATA IP block.

When used with the Storlink/Storm/Cortina Systems Gemini
SoC, the PATA interfac

ata: Add driver for Faraday Technology FTIDE010

This adds a driver for the Faraday Technology FTIDE010
PATA IP block.

When used with the Storlink/Storm/Cortina Systems Gemini
SoC, the PATA interface is accompanied by a PATA<->SATA
bridge, so while the device appear as a PATA controller,
it attaches physically to SATA disks, and also has a
designated memory area with registers to set up the bridge.

The Gemini SATA bridge is separated into its own driver
file to make things modular and make it possible to reuse
the PATA driver as stand-alone on other systems than the
Gemini.

dmesg excerpt from the D-Link DIR-685 storage router:
gemini-sata-bridge 46000000.sata: SATA ID 00000e00, PHY ID: 01000100
gemini-sata-bridge 46000000.sata: set up the Gemini IDE/SATA nexus
ftide010 63000000.ata: set up Gemini PATA0
ftide010 63000000.ata: device ID 00000500, irq 26, io base 0x63000000
ftide010 63000000.ata: SATA0 (master) start
gemini-sata-bridge 46000000.sata: SATA0 PHY ready
scsi host0: pata-ftide010
ata1: PATA max UDMA/133 irq 26
ata1.00: ATA-8: INTEL SSDSA2CW120G3, 4PC10302, max UDMA/133
ata1.00: 234441648 sectors, multi 1: LBA48 NCQ (depth 0/32)
ata1.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access ATA INTEL SSDSA2CW12 0302 PQ: 0 ANSI: 5
ata1.00: Enabling discard_zeroes_data
sd 0:0:0:0: [sda] 234441648 512-byte logical blocks: (120 GB/112 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
ata1.00: Enabling discard_zeroes_data
ata1.00: Enabling discard_zeroes_data
sd 0:0:0:0: [sda] Attached SCSI disk

After this I can flawlessly mount and read/write copy etc files
from /dev/sda[n].

Cc: John Feng-Hsin Chiang <john453@faraday-tech.com>
Cc: Greentime Hu <green.hu@gmail.com>
Acked-by: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>

show more ...

Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC driver updates from Olof Johansson:
"Driver updates for ARM SoCs:

Reset subsystem, merged thr

Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC driver updates from Olof Johansson:
"Driver updates for ARM SoCs:

Reset subsystem, merged through arm-soc by tradition:
- Make bool drivers explicitly non-modular
- New support for i.MX7 and Arria10 reset controllers

PATA driver for Palmchip BK371 (acked by Tejun)

Power domain drivers for i.MX (GPC, GPCv2)
- Moved out of mach-imx for GPC
- Bunch of tweaks, fixes, etc

PMC support for Tegra186

SoC detection support for Renesas RZ/G1H and RZ/G1N

Move Tegra flow controller driver from mach directory to drivers/soc
- (Power management / CPU power driver)

Misc smaller tweaks for other platforms"

* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (60 commits)
soc: pm-domain: Fix the mangled urls
soc: renesas: rcar-sysc: Add support for R-Car H3 ES2.0
soc: renesas: rcar-sysc: Add support for fixing up power area tables
soc: renesas: Register SoC device early
soc: imx: gpc: add workaround for i.MX6QP to the GPC PD driver
dt-bindings: imx-gpc: add i.MX6 QuadPlus compatible
soc: imx: gpc: add defines for domain index
soc: imx: Add GPCv2 power gating driver
dt-bindings: Add GPCv2 power gating driver
ARM/clk: move the ICST library to drivers/clk
ARM: plat-versatile: remove stale clock header
ARM: keystone: Drop PM domain support for k2g
soc: ti: Add ti_sci_pm_domains driver
dt-bindings: Add TI SCI PM Domains
PM / Domains: Do not check if simple providers have phandle cells
PM / Domains: Add generic data pointer to genpd data struct
soc/tegra: Add initial flowctrl support for Tegra132/210
soc/tegra: flowctrl: Add basic platform driver
soc/tegra: Move Tegra flowctrl driver
ARM: tegra: Remove unnecessary inclusion of flowctrl header
...

show more ...

ata: add Palmchip BK3710 PATA controller driver

Add Palmchip BK3710 PATA controller driver.

Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed

ata: add Palmchip BK3710 PATA controller driver

Add Palmchip BK3710 PATA controller driver.

Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>

show more ...

ata: ahci: add support for DaVinci DM816 SATA controller

This SATA controller is quite similar to the one present on the DA850
SoC, but the PHY configuration is different and it supports two HBA
por

ata: ahci: add support for DaVinci DM816 SATA controller

This SATA controller is quite similar to the one present on the DA850
SoC, but the PHY configuration is different and it supports two HBA
ports.

The IP suffers from the same PMP issue the DA850 does - if we enable
PMP but don't use it - softreset fails. Appropriate workaround was
implemented in this driver as well.

Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Tejun Heo <tj@kernel.org>

show more ...

pata: remove the at91 driver

This driver is orphan since commit b2026f708e09 ("ARM: at91: remove
at91sam9260/at91sam9g20 legacy board support"). Given that nobody cared
adding DT support to it, it p

pata: remove the at91 driver

This driver is orphan since commit b2026f708e09 ("ARM: at91: remove
at91sam9260/at91sam9g20 legacy board support"). Given that nobody cared
adding DT support to it, it probably means it's no longer used and is
thus a good candidate for removal.

Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Tejun Heo <tj@kernel.org>

show more ...

ata: add Atari Falcon PATA controller driver

Add Atari Falcon PATA controller driver. The major difference
when compared to legacy IDE's falconide host driver is that we
are using polled PIO mode a

ata: add Atari Falcon PATA controller driver

Add Atari Falcon PATA controller driver. The major difference
when compared to legacy IDE's falconide host driver is that we
are using polled PIO mode and thus avoiding the need for STDMA
locking magic altogether.

Tested under ARAnyM emulator.

Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>

show more ...

ata: ahci_brcmstb: rename to support across Broadcom SoC's

Rename the existing Broadcom STB ahci driver to common
Broadcom SATA3 driver to share this across Broadcom SoCs.

Signed-off-by: Yendapally

ata: ahci_brcmstb: rename to support across Broadcom SoC's

Rename the existing Broadcom STB ahci driver to common
Broadcom SATA3 driver to share this across Broadcom SoCs.

Signed-off-by: Yendapally Reddy Dhananjaya Reddy <yendapally.reddy@broadcom.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>

show more ...

ata: add AMD Seattle platform driver

AMD Seattle SATA controller mostly conforms to AHCI interface with some
special register to control SGPIO interface. In the case of an AHCI
controller, the SGPIO

ata: add AMD Seattle platform driver

AMD Seattle SATA controller mostly conforms to AHCI interface with some
special register to control SGPIO interface. In the case of an AHCI
controller, the SGPIO feature is ideally implemented using the
"Enclosure Management" register of the AHCI controller, but those
registeres are not implemented in the Seattle SoC. Instead SoC
(Rev B0 onwards) provides a 32-bit SGPIO control register which should
be programmed to control the activity, locate and fault LEDs.

The driver is based on ahci_platform driver.

Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
CC: tj@kernel.org
CC: linux-ide@vger.kernel.org
Signed-off-by: Tejun Heo <tj@kernel.org>

show more ...