Merge tag 'gpio-updates-for-v6.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux

Pull gpio updates from Bartosz Golaszewski:
"We have three new drivers, some refactoring in the GP

Merge tag 'gpio-updates-for-v6.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux

Pull gpio updates from Bartosz Golaszewski:
"We have three new drivers, some refactoring in the GPIO core, lots of
various changes across many drivers, new configfs interface for the
virtual gpio-aggregator module and DT-bindings updates.

The treewide conversion of GPIO drivers to using the new value setter
callbacks is ongoing with another round of GPIO drivers updated. You
will also see these commits coming in from other subsystems as with
the relevant changes merged into mainline last cycle, I've started
converting GPIO providers located elsewhere than drivers/gpio/.

GPIO core:
- use more lock guards where applicable
- refactor GPIO ACPI code and shrink it in the process by 8%
- move GPIO ACPI quirks into a separate file
- remove unneeded #ifdef
- convert GPIO devres helpers to using devm_add_action() where
applicable which shrinks and simplifies the code
- refactor GPIO descriptor validation in GPIO consumer interfaces
- don't allow setting values on input lines in the GPIO core which
will take off the burden from GPIO drivers of checking this down
the line
- provide gpiod_is_equal() as a way of safely comparing two GPIO
descriptors (the only current user is in regulator core)

New drivers:
- add the GPIO module for the max77759 multifunction device
- add the GPIO driver for the VeriSilicon BLZP1600 GPIO controller
- add the GPIO driver for the Spacemit K1 SoC

Driver improvements:
- convert more drivers to using the new GPIO line value setter
callbacks
- convert more drivers to making the irq_chip immutable as is
recommended by the interrupt subsystem
- extend build testing coverage by enabling more modules to be built
with COMPILE_TEST=y
- extend the gpio-aggregator module with a configfs interface that
makes the setup easier for user-space than the existing
driver-level sysfs attributes and also adds more advanced
configuration features (such as referring to aggregated lines by
their original names or modifying their names as exposed by the
aggregated chip)
- add a missing mutex_destroy() in gpio-imx-scu
- add an OF polarity quirk for s5m8767
- allow building gpio-vf610 as a loadable module
- make gpio-mxc not hardcode its GPIO base number with GPIO SYSFS
interface disabled (another small step towards getting rid of the
global GPIO numberspace)
- add support for level-triggered interrupts to gpio-pca953x
- don't double-check the ngpios property in gpio-ds4520 as GPIO core
already does it
- don't double-check the number of GPIOs in gpio-imx-scu as GPIO core
already does it
- remove unused callbacks from gpio-max3191x

DT bindings:
- add device-tree bindings for max77759, spacemit,k1 and blzp1600
(new drivers added this cycle)
- document more properties for gpio-vf610 and gpio-tegra186
- document a new pca95xx variant
- fix style of examples in several GPIO DT-binding documents

Misc:
- TODO list updates"

* tag 'gpio-updates-for-v6.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux: (123 commits)
gpio: timberdale: select GPIOLIB_IRQCHIP
gpio: lpc18xx: select GPIOLIB_IRQCHIP
gpio: grgpio: select GPIOLIB_IRQCHIP
gpio: bcm-kona: select GPIOLIB_IRQCHIP
dt-bindings: gpio: vf610: add ngpios and gpio-reserved-ranges
gpio: davinci: select GPIOLIB_IRQCHIP
gpiolib-acpi: Update file references in the Documentation and MAINTAINERS
gpiolib: acpi: Move quirks to a separate file
gpiolib: acpi: Add acpi_gpio_need_run_edge_events_on_boot() getter
gpiolib: acpi: Handle deferred list via new API
gpiolib: acpi: Make sure we fill struct acpi_gpio_info
gpiolib: acpi: Switch to use enum in acpi_gpio_in_ignore_list()
gpiolib: acpi: Use temporary variable for struct acpi_gpio_info
gpiolib: remove unneeded #ifdef
gpio: mpc8xxx: select GPIOLIB_IRQCHIP
gpio: pxa: select GPIOLIB_IRQCHIP
gpio: pxa: Make irq_chip immutable
gpio: timberdale: Make irq_chip immutable
gpio: xgene-sb: Make irq_chip immutable
gpio: davinci: Make irq_chip immutable
...

show more ...

dt-bindings: gpio: Correct indentation and style in DTS example

DTS example in the bindings should be indented with 2- or 4-spaces and
aligned with opening '- |', so correct any differences like 3-s

dt-bindings: gpio: Correct indentation and style in DTS example

DTS example in the bindings should be indented with 2- or 4-spaces and
aligned with opening '- |', so correct any differences like 3-spaces or
mixtures 2- and 4-spaces in one binding. While re-indenting, drop
unused labels.

No functional changes here, but saves some comments during reviews of
new patches built on existing code.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Sander Vanheule <sander@svanheule.net>
Reviewed-by: Manikandan Muralidharan <manikandan.m@microchip.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Link: https://lore.kernel.org/r/20250324125326.82270-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>

show more ...

Merge drm/drm-next into drm-intel-gt-next

We need
4ba4f1afb6a9 ("perf: Generic hotplug support for a PMU with a scope")
in order to land a i915 PMU simplification and a fix. That landed in 6.12
and

Merge drm/drm-next into drm-intel-gt-next

We need
4ba4f1afb6a9 ("perf: Generic hotplug support for a PMU with a scope")
in order to land a i915 PMU simplification and a fix. That landed in 6.12
and we are stuck at 6.9 so lets bump things forward.

Signed-off-by: Tvrtko Ursulin <tursulin@ursulin.net>

show more ...

Merge branch 'next' into for-linus

Prepare input updates for 6.12 merge window.

Merge branch 'ib/6.11-rc6-matrix-keypad-spitz' into next

Bring in changes removing support for platform data from matrix-keypad
driver.

Merge tag 'v6.11-rc1' into clk-meson-next

Linux 6.11-rc1

Merge tag 'v6.11-rc3' into trace/ring-buffer/core

The "reserve_mem" kernel command line parameter has been pulled into
v6.11. Merge the latest -rc3 to allow the persistent ring buffer memory to
be a

Merge tag 'v6.11-rc3' into trace/ring-buffer/core

The "reserve_mem" kernel command line parameter has been pulled into
v6.11. Merge the latest -rc3 to allow the persistent ring buffer memory to
be able to be mapped at the address specified by the "reserve_mem" command
line parameter.

Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>

show more ...

Merge tag 'v6.11-rc1' into for-6.12

Linux 6.11-rc1

Merge drm/drm-next into drm-xe-next

Get drm-xe-next on v6.11-rc2 and synchronized with drm-intel-next for
the display side. This resolves the current conflict for the
enable_display module parameter

Merge drm/drm-next into drm-xe-next

Get drm-xe-next on v6.11-rc2 and synchronized with drm-intel-next for
the display side. This resolves the current conflict for the
enable_display module parameter and allows further pending refactors.

Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>

show more ...

Merge drm/drm-next into drm-misc-next

Get drm-misc-next to the state of v6.11-rc2.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>

Merge drm/drm-next into drm-intel-next

Sync with v6.11-rc1 in general, and specifically get the new
BACKLIGHT_POWER_ constants for power states.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>

Merge branch 'linus' into x86/mm

Bring x86 and selftests up to date

Merge drm/drm-fixes into drm-misc-fixes

Let's start the new drm-misc-fixes cycle by bringing in 6.11-rc1.

Signed-off-by: Maxime Ripard <mripard@kernel.org>

Merge tag 'gpio-updates-for-v6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux

Pull gpio updates from Bartosz Golaszewski:
"The majority of added lines are two new modules: the

Merge tag 'gpio-updates-for-v6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux

Pull gpio updates from Bartosz Golaszewski:
"The majority of added lines are two new modules: the GPIO virtual
consumer module that improves our ability to add automated tests for
the kernel API and the "sloppy" logic analyzer module that uses the
GPIO API to implement a coarse-grained debugging tool for useful for
remote development.

Other than that we have the usual assortment of various driver
extensions, improvements to the core GPIO code, DT-bindings and other
documentation updates as well as an extension to the interrupt
simulator:

GPIOLIB core:
- rework kfifo handling rework in the character device code
- improve the labeling of GPIOs requested as interrupts and show more
info on interrupt-only GPIOs in debugfs
- remove unused APIs
- unexport interfaces that are only used from the core GPIO code
- drop the return value from gpiochip_set_desc_names() as it cannot
fail
- move a string array definition out of a header and into a specific
compilation unit
- convert the last user of gpiochip_get_desc() other than GPIO core
to using a safer alternative
- use array_index_nospec() where applicable

New drivers:
- add a "virtual GPIO consumer" module that allows requesting GPIOs
from actual hardware and driving tests of the in-kernel GPIO API
from user-space over debugfs
- add a GPIO-based "sloppy" logic analyzer module useful for "first
glance" debugging on remote boards

Driver improvements:
- add support for a new model to gpio-pca953x
- lock GPIOs as interrupts in gpio-sim when the lines are requested
as irqs via the simulator domain + some other minor improvements
- improve error reporting in gpio-syscon
- convert gpio-ath79 to using dynamic GPIO base and range
- use pcibios_err_to_errno() for converting PCIBIOS error codes to
errno vaues in gpio-amd8111 and gpio-rdc321x
- allow building gpio-brcmstb for the BCM2835 architecture

DT bindings:
- convert DT bindings for lsi,zevio, mpc8xxx, and atmel to DT schema
- document new properties for aspeed,gpio, fsl,qoriq-gpio and
gpio-vf610
- document new compatibles for pca953x and fsl,qoriq-gpio

Documentation:
- document stricter behavior of the GPIO character device uAPI with
regards to reconfiguring requested line without direction set
- clarify the effect of the active-low flag on line values and edges
- remove documentation for the legacy GPIO API in order to stop
tempting people to use it
- document the preference for using pread() for reading edge events
in the sysfs API

Other:
- add an extended initializer to the interrupt simulator allowing to
specify a number of callbacks callers can use to be notified about
irqs being requested and released"

* tag 'gpio-updates-for-v6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux: (41 commits)
gpio: mc33880: Convert comma to semicolon
gpio: virtuser: actually use the "trimmed" local variable
dt-bindings: gpio: convert Atmel GPIO to json-schema
gpio: virtuser: new virtual testing driver for the GPIO API
dt-bindings: gpio: vf610: Allow gpio-line-names to be set
gpio: sim: lock GPIOs as interrupts when they are requested
genirq/irq_sim: add an extended irq_sim initializer
dt-bindings: gpio: fsl,qoriq-gpio: Add compatible string fsl,ls1046a-gpio
gpiolib: unexport gpiochip_get_desc()
gpio: add sloppy logic analyzer using polling
Documentation: gpio: Reconfiguration with unset direction (uAPI v2)
Documentation: gpio: Reconfiguration with unset direction (uAPI v1)
dt-bindings: gpio: fsl,qoriq-gpio: add common property gpio-line-names
gpio: ath79: convert to dynamic GPIO base allocation
pinctrl: da9062: replace gpiochip_get_desc() with gpio_device_get_desc()
gpiolib: put gpio_suffixes in a single compilation unit
Documentation: gpio: Clarify effect of active low flag on line edges
Documentation: gpio: Clarify effect of active low flag on line values
gpiolib: Remove data-less gpiochip_add() function
gpio: sim: use devm_mutex_init()
...

show more ...

dt-bindings: gpio: convert Atmel GPIO to json-schema

Convert the Atmel GPIO controller binding document to DT schema format
using json-schema.
The at91 pinctrl driver uses "atmel,at91rm9200-gpio" co

dt-bindings: gpio: convert Atmel GPIO to json-schema

Convert the Atmel GPIO controller binding document to DT schema format
using json-schema.
The at91 pinctrl driver uses "atmel,at91rm9200-gpio" compatible string
to find the number of active GPIO banks and identify the pinmux nodes.
"atmel,at91sam9x5-gpio" and "microchip,sam9x60-gpio" have additional
registers to handle drive-strength, slew-rate, pull-down to drive the
pinmux configs.
The new compatible string "microchip,sam9x7-gpio" is added.

Signed-off-by: Manikandan Muralidharan <manikandan.m@microchip.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20240709092354.191643-5-manikandan.m@microchip.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>

show more ...