xref: /linux/sound/soc/ux500/ux500_msp_i2s.c (revision 3d0fe49454652117522f60bfbefb978ba0e5300b)
1 // SPDX-License-Identifier: GPL-2.0-only
2 /*
3  * Copyright (C) ST-Ericsson SA 2012
4  *
5  * Author: Ola Lilja <ola.o.lilja@stericsson.com>,
6  *         Roger Nilsson <roger.xr.nilsson@stericsson.com>,
7  *         Sandeep Kaushik <sandeep.kaushik@st.com>
8  *         for ST-Ericsson.
9  */
10 
11 #include <linux/module.h>
12 #include <linux/platform_device.h>
13 #include <linux/delay.h>
14 #include <linux/slab.h>
15 #include <linux/io.h>
16 #include <linux/of.h>
17 
18 #include <sound/soc.h>
19 
20 #include "ux500_msp_i2s.h"
21 
22  /* Protocol desciptors */
23 static const struct msp_protdesc prot_descs[] = {
24 	{ /* I2S */
25 		MSP_SINGLE_PHASE,
26 		MSP_SINGLE_PHASE,
27 		MSP_PHASE2_START_MODE_IMEDIATE,
28 		MSP_PHASE2_START_MODE_IMEDIATE,
29 		MSP_BTF_MS_BIT_FIRST,
30 		MSP_BTF_MS_BIT_FIRST,
31 		MSP_FRAME_LEN_1,
32 		MSP_FRAME_LEN_1,
33 		MSP_FRAME_LEN_1,
34 		MSP_FRAME_LEN_1,
35 		MSP_ELEM_LEN_32,
36 		MSP_ELEM_LEN_32,
37 		MSP_ELEM_LEN_32,
38 		MSP_ELEM_LEN_32,
39 		MSP_DELAY_1,
40 		MSP_DELAY_1,
41 		MSP_RISING_EDGE,
42 		MSP_FALLING_EDGE,
43 		MSP_FSYNC_POL_ACT_LO,
44 		MSP_FSYNC_POL_ACT_LO,
45 		MSP_SWAP_NONE,
46 		MSP_SWAP_NONE,
47 		MSP_COMPRESS_MODE_LINEAR,
48 		MSP_EXPAND_MODE_LINEAR,
49 		MSP_FSYNC_IGNORE,
50 		31,
51 		15,
52 		32,
53 	}, { /* PCM */
54 		MSP_DUAL_PHASE,
55 		MSP_DUAL_PHASE,
56 		MSP_PHASE2_START_MODE_FSYNC,
57 		MSP_PHASE2_START_MODE_FSYNC,
58 		MSP_BTF_MS_BIT_FIRST,
59 		MSP_BTF_MS_BIT_FIRST,
60 		MSP_FRAME_LEN_1,
61 		MSP_FRAME_LEN_1,
62 		MSP_FRAME_LEN_1,
63 		MSP_FRAME_LEN_1,
64 		MSP_ELEM_LEN_16,
65 		MSP_ELEM_LEN_16,
66 		MSP_ELEM_LEN_16,
67 		MSP_ELEM_LEN_16,
68 		MSP_DELAY_0,
69 		MSP_DELAY_0,
70 		MSP_RISING_EDGE,
71 		MSP_FALLING_EDGE,
72 		MSP_FSYNC_POL_ACT_HI,
73 		MSP_FSYNC_POL_ACT_HI,
74 		MSP_SWAP_NONE,
75 		MSP_SWAP_NONE,
76 		MSP_COMPRESS_MODE_LINEAR,
77 		MSP_EXPAND_MODE_LINEAR,
78 		MSP_FSYNC_IGNORE,
79 		255,
80 		0,
81 		256,
82 	}, { /* Companded PCM */
83 		MSP_SINGLE_PHASE,
84 		MSP_SINGLE_PHASE,
85 		MSP_PHASE2_START_MODE_FSYNC,
86 		MSP_PHASE2_START_MODE_FSYNC,
87 		MSP_BTF_MS_BIT_FIRST,
88 		MSP_BTF_MS_BIT_FIRST,
89 		MSP_FRAME_LEN_1,
90 		MSP_FRAME_LEN_1,
91 		MSP_FRAME_LEN_1,
92 		MSP_FRAME_LEN_1,
93 		MSP_ELEM_LEN_8,
94 		MSP_ELEM_LEN_8,
95 		MSP_ELEM_LEN_8,
96 		MSP_ELEM_LEN_8,
97 		MSP_DELAY_0,
98 		MSP_DELAY_0,
99 		MSP_RISING_EDGE,
100 		MSP_RISING_EDGE,
101 		MSP_FSYNC_POL_ACT_HI,
102 		MSP_FSYNC_POL_ACT_HI,
103 		MSP_SWAP_NONE,
104 		MSP_SWAP_NONE,
105 		MSP_COMPRESS_MODE_LINEAR,
106 		MSP_EXPAND_MODE_LINEAR,
107 		MSP_FSYNC_IGNORE,
108 		255,
109 		0,
110 		256,
111 	},
112 };
113 
114 static void set_prot_desc_tx(struct ux500_msp *msp,
115 			struct msp_protdesc *protdesc,
116 			enum msp_data_size data_size)
117 {
118 	u32 temp_reg = 0;
119 
120 	temp_reg |= MSP_P2_ENABLE_BIT(protdesc->tx_phase_mode);
121 	temp_reg |= MSP_P2_START_MODE_BIT(protdesc->tx_phase2_start_mode);
122 	temp_reg |= MSP_P1_FRAME_LEN_BITS(protdesc->tx_frame_len_1);
123 	temp_reg |= MSP_P2_FRAME_LEN_BITS(protdesc->tx_frame_len_2);
124 	if (msp->def_elem_len) {
125 		temp_reg |= MSP_P1_ELEM_LEN_BITS(protdesc->tx_elem_len_1);
126 		temp_reg |= MSP_P2_ELEM_LEN_BITS(protdesc->tx_elem_len_2);
127 	} else {
128 		temp_reg |= MSP_P1_ELEM_LEN_BITS(data_size);
129 		temp_reg |= MSP_P2_ELEM_LEN_BITS(data_size);
130 	}
131 	temp_reg |= MSP_DATA_DELAY_BITS(protdesc->tx_data_delay);
132 	temp_reg |= MSP_SET_ENDIANNES_BIT(protdesc->tx_byte_order);
133 	temp_reg |= MSP_FSYNC_POL(protdesc->tx_fsync_pol);
134 	temp_reg |= MSP_DATA_WORD_SWAP(protdesc->tx_half_word_swap);
135 	temp_reg |= MSP_SET_COMPANDING_MODE(protdesc->compression_mode);
136 	temp_reg |= MSP_SET_FSYNC_IGNORE(protdesc->frame_sync_ignore);
137 
138 	writel(temp_reg, msp->registers + MSP_TCF);
139 }
140 
141 static void set_prot_desc_rx(struct ux500_msp *msp,
142 			struct msp_protdesc *protdesc,
143 			enum msp_data_size data_size)
144 {
145 	u32 temp_reg = 0;
146 
147 	temp_reg |= MSP_P2_ENABLE_BIT(protdesc->rx_phase_mode);
148 	temp_reg |= MSP_P2_START_MODE_BIT(protdesc->rx_phase2_start_mode);
149 	temp_reg |= MSP_P1_FRAME_LEN_BITS(protdesc->rx_frame_len_1);
150 	temp_reg |= MSP_P2_FRAME_LEN_BITS(protdesc->rx_frame_len_2);
151 	if (msp->def_elem_len) {
152 		temp_reg |= MSP_P1_ELEM_LEN_BITS(protdesc->rx_elem_len_1);
153 		temp_reg |= MSP_P2_ELEM_LEN_BITS(protdesc->rx_elem_len_2);
154 	} else {
155 		temp_reg |= MSP_P1_ELEM_LEN_BITS(data_size);
156 		temp_reg |= MSP_P2_ELEM_LEN_BITS(data_size);
157 	}
158 
159 	temp_reg |= MSP_DATA_DELAY_BITS(protdesc->rx_data_delay);
160 	temp_reg |= MSP_SET_ENDIANNES_BIT(protdesc->rx_byte_order);
161 	temp_reg |= MSP_FSYNC_POL(protdesc->rx_fsync_pol);
162 	temp_reg |= MSP_DATA_WORD_SWAP(protdesc->rx_half_word_swap);
163 	temp_reg |= MSP_SET_COMPANDING_MODE(protdesc->expansion_mode);
164 	temp_reg |= MSP_SET_FSYNC_IGNORE(protdesc->frame_sync_ignore);
165 
166 	writel(temp_reg, msp->registers + MSP_RCF);
167 }
168 
169 static int configure_protocol(struct ux500_msp *msp,
170 			struct ux500_msp_config *config)
171 {
172 	struct msp_protdesc *protdesc;
173 	enum msp_data_size data_size;
174 	u32 temp_reg = 0;
175 
176 	data_size = config->data_size;
177 	msp->def_elem_len = config->def_elem_len;
178 	if (config->default_protdesc == 1) {
179 		if (config->protocol >= MSP_INVALID_PROTOCOL) {
180 			dev_err(msp->dev, "%s: ERROR: Invalid protocol!\n",
181 				__func__);
182 			return -EINVAL;
183 		}
184 		protdesc =
185 		    (struct msp_protdesc *)&prot_descs[config->protocol];
186 	} else {
187 		protdesc = (struct msp_protdesc *)&config->protdesc;
188 	}
189 
190 	if (data_size < MSP_DATA_BITS_DEFAULT || data_size > MSP_DATA_BITS_32) {
191 		dev_err(msp->dev,
192 			"%s: ERROR: Invalid data-size requested (data_size = %d)!\n",
193 			__func__, data_size);
194 		return -EINVAL;
195 	}
196 
197 	if (config->direction & MSP_DIR_TX)
198 		set_prot_desc_tx(msp, protdesc, data_size);
199 	if (config->direction & MSP_DIR_RX)
200 		set_prot_desc_rx(msp, protdesc, data_size);
201 
202 	/* The code below should not be separated. */
203 	temp_reg = readl(msp->registers + MSP_GCR) & ~TX_CLK_POL_RISING;
204 	temp_reg |= MSP_TX_CLKPOL_BIT(~protdesc->tx_clk_pol);
205 	writel(temp_reg, msp->registers + MSP_GCR);
206 	temp_reg = readl(msp->registers + MSP_GCR) & ~RX_CLK_POL_RISING;
207 	temp_reg |= MSP_RX_CLKPOL_BIT(protdesc->rx_clk_pol);
208 	writel(temp_reg, msp->registers + MSP_GCR);
209 
210 	return 0;
211 }
212 
213 static int setup_bitclk(struct ux500_msp *msp, struct ux500_msp_config *config)
214 {
215 	u32 reg_val_GCR;
216 	u32 frame_per = 0;
217 	u32 sck_div = 0;
218 	u32 frame_width = 0;
219 	u32 temp_reg = 0;
220 	struct msp_protdesc *protdesc = NULL;
221 
222 	reg_val_GCR = readl(msp->registers + MSP_GCR);
223 	writel(reg_val_GCR & ~SRG_ENABLE, msp->registers + MSP_GCR);
224 
225 	if (config->default_protdesc)
226 		protdesc =
227 			(struct msp_protdesc *)&prot_descs[config->protocol];
228 	else
229 		protdesc = (struct msp_protdesc *)&config->protdesc;
230 
231 	switch (config->protocol) {
232 	case MSP_PCM_PROTOCOL:
233 	case MSP_PCM_COMPAND_PROTOCOL:
234 		frame_width = protdesc->frame_width;
235 		sck_div = config->f_inputclk / (config->frame_freq *
236 			(protdesc->clocks_per_frame));
237 		frame_per = protdesc->frame_period;
238 		break;
239 	case MSP_I2S_PROTOCOL:
240 		frame_width = protdesc->frame_width;
241 		sck_div = config->f_inputclk / (config->frame_freq *
242 			(protdesc->clocks_per_frame));
243 		frame_per = protdesc->frame_period;
244 		break;
245 	default:
246 		dev_err(msp->dev, "%s: ERROR: Unknown protocol (%d)!\n",
247 			__func__,
248 			config->protocol);
249 		return -EINVAL;
250 	}
251 
252 	temp_reg = (sck_div - 1) & SCK_DIV_MASK;
253 	temp_reg |= FRAME_WIDTH_BITS(frame_width);
254 	temp_reg |= FRAME_PERIOD_BITS(frame_per);
255 	writel(temp_reg, msp->registers + MSP_SRG);
256 
257 	msp->f_bitclk = (config->f_inputclk)/(sck_div + 1);
258 
259 	/* Enable bit-clock */
260 	udelay(100);
261 	reg_val_GCR = readl(msp->registers + MSP_GCR);
262 	writel(reg_val_GCR | SRG_ENABLE, msp->registers + MSP_GCR);
263 	udelay(100);
264 
265 	return 0;
266 }
267 
268 static int configure_multichannel(struct ux500_msp *msp,
269 				struct ux500_msp_config *config)
270 {
271 	struct msp_protdesc *protdesc;
272 	struct msp_multichannel_config *mcfg;
273 	u32 reg_val_MCR;
274 
275 	if (config->default_protdesc == 1) {
276 		if (config->protocol >= MSP_INVALID_PROTOCOL) {
277 			dev_err(msp->dev,
278 				"%s: ERROR: Invalid protocol (%d)!\n",
279 				__func__, config->protocol);
280 			return -EINVAL;
281 		}
282 		protdesc = (struct msp_protdesc *)
283 				&prot_descs[config->protocol];
284 	} else {
285 		protdesc = (struct msp_protdesc *)&config->protdesc;
286 	}
287 
288 	mcfg = &config->multichannel_config;
289 	if (mcfg->tx_multichannel_enable) {
290 		if (protdesc->tx_phase_mode == MSP_SINGLE_PHASE) {
291 			reg_val_MCR = readl(msp->registers + MSP_MCR);
292 			writel(reg_val_MCR | (mcfg->tx_multichannel_enable ?
293 						1 << TMCEN_BIT : 0),
294 				msp->registers + MSP_MCR);
295 			writel(mcfg->tx_channel_0_enable,
296 				msp->registers + MSP_TCE0);
297 			writel(mcfg->tx_channel_1_enable,
298 				msp->registers + MSP_TCE1);
299 			writel(mcfg->tx_channel_2_enable,
300 				msp->registers + MSP_TCE2);
301 			writel(mcfg->tx_channel_3_enable,
302 				msp->registers + MSP_TCE3);
303 		} else {
304 			dev_err(msp->dev,
305 				"%s: ERROR: Only single-phase supported (TX-mode: %d)!\n",
306 				__func__, protdesc->tx_phase_mode);
307 			return -EINVAL;
308 		}
309 	}
310 	if (mcfg->rx_multichannel_enable) {
311 		if (protdesc->rx_phase_mode == MSP_SINGLE_PHASE) {
312 			reg_val_MCR = readl(msp->registers + MSP_MCR);
313 			writel(reg_val_MCR | (mcfg->rx_multichannel_enable ?
314 						1 << RMCEN_BIT : 0),
315 				msp->registers + MSP_MCR);
316 			writel(mcfg->rx_channel_0_enable,
317 					msp->registers + MSP_RCE0);
318 			writel(mcfg->rx_channel_1_enable,
319 					msp->registers + MSP_RCE1);
320 			writel(mcfg->rx_channel_2_enable,
321 					msp->registers + MSP_RCE2);
322 			writel(mcfg->rx_channel_3_enable,
323 					msp->registers + MSP_RCE3);
324 		} else {
325 			dev_err(msp->dev,
326 				"%s: ERROR: Only single-phase supported (RX-mode: %d)!\n",
327 				__func__, protdesc->rx_phase_mode);
328 			return -EINVAL;
329 		}
330 		if (mcfg->rx_comparison_enable_mode) {
331 			reg_val_MCR = readl(msp->registers + MSP_MCR);
332 			writel(reg_val_MCR |
333 				(mcfg->rx_comparison_enable_mode << RCMPM_BIT),
334 				msp->registers + MSP_MCR);
335 
336 			writel(mcfg->comparison_mask,
337 					msp->registers + MSP_RCM);
338 			writel(mcfg->comparison_value,
339 					msp->registers + MSP_RCV);
340 
341 		}
342 	}
343 
344 	return 0;
345 }
346 
347 static int enable_msp(struct ux500_msp *msp, struct ux500_msp_config *config)
348 {
349 	int status = 0;
350 	u32 reg_val_DMACR, reg_val_GCR;
351 
352 	/* Configure msp with protocol dependent settings */
353 	configure_protocol(msp, config);
354 	setup_bitclk(msp, config);
355 	if (config->multichannel_configured == 1) {
356 		status = configure_multichannel(msp, config);
357 		if (status)
358 			dev_warn(msp->dev,
359 				"%s: WARN: configure_multichannel failed (%d)!\n",
360 				__func__, status);
361 	}
362 
363 	reg_val_DMACR = readl(msp->registers + MSP_DMACR);
364 	if (config->direction & MSP_DIR_RX)
365 		reg_val_DMACR |= RX_DMA_ENABLE;
366 	if (config->direction & MSP_DIR_TX)
367 		reg_val_DMACR |= TX_DMA_ENABLE;
368 	writel(reg_val_DMACR, msp->registers + MSP_DMACR);
369 
370 	writel(config->iodelay, msp->registers + MSP_IODLY);
371 
372 	/* Enable frame generation logic */
373 	reg_val_GCR = readl(msp->registers + MSP_GCR);
374 	writel(reg_val_GCR | FRAME_GEN_ENABLE, msp->registers + MSP_GCR);
375 
376 	return status;
377 }
378 
379 static void flush_fifo_rx(struct ux500_msp *msp)
380 {
381 	u32 reg_val_GCR, reg_val_FLR;
382 	u32 limit = 32;
383 
384 	reg_val_GCR = readl(msp->registers + MSP_GCR);
385 	writel(reg_val_GCR | RX_ENABLE, msp->registers + MSP_GCR);
386 
387 	reg_val_FLR = readl(msp->registers + MSP_FLR);
388 	while (!(reg_val_FLR & RX_FIFO_EMPTY) && limit--) {
389 		readl(msp->registers + MSP_DR);
390 		reg_val_FLR = readl(msp->registers + MSP_FLR);
391 	}
392 
393 	writel(reg_val_GCR, msp->registers + MSP_GCR);
394 }
395 
396 static void flush_fifo_tx(struct ux500_msp *msp)
397 {
398 	u32 reg_val_GCR, reg_val_FLR;
399 	u32 limit = 32;
400 
401 	reg_val_GCR = readl(msp->registers + MSP_GCR);
402 	writel(reg_val_GCR | TX_ENABLE, msp->registers + MSP_GCR);
403 	writel(MSP_ITCR_ITEN | MSP_ITCR_TESTFIFO, msp->registers + MSP_ITCR);
404 
405 	reg_val_FLR = readl(msp->registers + MSP_FLR);
406 	while (!(reg_val_FLR & TX_FIFO_EMPTY) && limit--) {
407 		readl(msp->registers + MSP_TSTDR);
408 		reg_val_FLR = readl(msp->registers + MSP_FLR);
409 	}
410 	writel(0x0, msp->registers + MSP_ITCR);
411 	writel(reg_val_GCR, msp->registers + MSP_GCR);
412 }
413 
414 int ux500_msp_i2s_open(struct ux500_msp *msp,
415 		struct ux500_msp_config *config)
416 {
417 	u32 old_reg, new_reg, mask;
418 	int res;
419 	unsigned int tx_sel, rx_sel, tx_busy, rx_busy;
420 
421 	if (in_interrupt()) {
422 		dev_err(msp->dev,
423 			"%s: ERROR: Open called in interrupt context!\n",
424 			__func__);
425 		return -1;
426 	}
427 
428 	tx_sel = (config->direction & MSP_DIR_TX) > 0;
429 	rx_sel = (config->direction & MSP_DIR_RX) > 0;
430 	if (!tx_sel && !rx_sel) {
431 		dev_err(msp->dev, "%s: Error: No direction selected!\n",
432 			__func__);
433 		return -EINVAL;
434 	}
435 
436 	tx_busy = (msp->dir_busy & MSP_DIR_TX) > 0;
437 	rx_busy = (msp->dir_busy & MSP_DIR_RX) > 0;
438 	if (tx_busy && tx_sel) {
439 		dev_err(msp->dev, "%s: Error: TX is in use!\n", __func__);
440 		return -EBUSY;
441 	}
442 	if (rx_busy && rx_sel) {
443 		dev_err(msp->dev, "%s: Error: RX is in use!\n", __func__);
444 		return -EBUSY;
445 	}
446 
447 	msp->dir_busy |= (tx_sel ? MSP_DIR_TX : 0) | (rx_sel ? MSP_DIR_RX : 0);
448 
449 	/* First do the global config register */
450 	mask = RX_CLK_SEL_MASK | TX_CLK_SEL_MASK | RX_FSYNC_MASK |
451 	    TX_FSYNC_MASK | RX_SYNC_SEL_MASK | TX_SYNC_SEL_MASK |
452 	    RX_FIFO_ENABLE_MASK | TX_FIFO_ENABLE_MASK | SRG_CLK_SEL_MASK |
453 	    LOOPBACK_MASK | TX_EXTRA_DELAY_MASK;
454 
455 	new_reg = (config->tx_clk_sel | config->rx_clk_sel |
456 		config->rx_fsync_pol | config->tx_fsync_pol |
457 		config->rx_fsync_sel | config->tx_fsync_sel |
458 		config->rx_fifo_config | config->tx_fifo_config |
459 		config->srg_clk_sel | config->loopback_enable |
460 		config->tx_data_enable);
461 
462 	old_reg = readl(msp->registers + MSP_GCR);
463 	old_reg &= ~mask;
464 	new_reg |= old_reg;
465 	writel(new_reg, msp->registers + MSP_GCR);
466 
467 	res = enable_msp(msp, config);
468 	if (res < 0) {
469 		dev_err(msp->dev, "%s: ERROR: enable_msp failed (%d)!\n",
470 			__func__, res);
471 		return -EBUSY;
472 	}
473 	if (config->loopback_enable & 0x80)
474 		msp->loopback_enable = 1;
475 
476 	/* Flush FIFOs */
477 	flush_fifo_tx(msp);
478 	flush_fifo_rx(msp);
479 
480 	msp->msp_state = MSP_STATE_CONFIGURED;
481 	return 0;
482 }
483 
484 static void disable_msp_rx(struct ux500_msp *msp)
485 {
486 	u32 reg_val_GCR, reg_val_DMACR, reg_val_IMSC;
487 
488 	reg_val_GCR = readl(msp->registers + MSP_GCR);
489 	writel(reg_val_GCR & ~RX_ENABLE, msp->registers + MSP_GCR);
490 	reg_val_DMACR = readl(msp->registers + MSP_DMACR);
491 	writel(reg_val_DMACR & ~RX_DMA_ENABLE, msp->registers + MSP_DMACR);
492 	reg_val_IMSC = readl(msp->registers + MSP_IMSC);
493 	writel(reg_val_IMSC &
494 			~(RX_SERVICE_INT | RX_OVERRUN_ERROR_INT),
495 			msp->registers + MSP_IMSC);
496 
497 	msp->dir_busy &= ~MSP_DIR_RX;
498 }
499 
500 static void disable_msp_tx(struct ux500_msp *msp)
501 {
502 	u32 reg_val_GCR, reg_val_DMACR, reg_val_IMSC;
503 
504 	reg_val_GCR = readl(msp->registers + MSP_GCR);
505 	writel(reg_val_GCR & ~TX_ENABLE, msp->registers + MSP_GCR);
506 	reg_val_DMACR = readl(msp->registers + MSP_DMACR);
507 	writel(reg_val_DMACR & ~TX_DMA_ENABLE, msp->registers + MSP_DMACR);
508 	reg_val_IMSC = readl(msp->registers + MSP_IMSC);
509 	writel(reg_val_IMSC &
510 			~(TX_SERVICE_INT | TX_UNDERRUN_ERR_INT),
511 			msp->registers + MSP_IMSC);
512 
513 	msp->dir_busy &= ~MSP_DIR_TX;
514 }
515 
516 static int disable_msp(struct ux500_msp *msp, unsigned int dir)
517 {
518 	u32 reg_val_GCR;
519 	unsigned int disable_tx, disable_rx;
520 
521 	reg_val_GCR = readl(msp->registers + MSP_GCR);
522 	disable_tx = dir & MSP_DIR_TX;
523 	disable_rx = dir & MSP_DIR_TX;
524 	if (disable_tx && disable_rx) {
525 		reg_val_GCR = readl(msp->registers + MSP_GCR);
526 		writel(reg_val_GCR | LOOPBACK_MASK,
527 				msp->registers + MSP_GCR);
528 
529 		/* Flush TX-FIFO */
530 		flush_fifo_tx(msp);
531 
532 		/* Disable TX-channel */
533 		writel((readl(msp->registers + MSP_GCR) &
534 			       (~TX_ENABLE)), msp->registers + MSP_GCR);
535 
536 		/* Flush RX-FIFO */
537 		flush_fifo_rx(msp);
538 
539 		/* Disable Loopback and Receive channel */
540 		writel((readl(msp->registers + MSP_GCR) &
541 				(~(RX_ENABLE | LOOPBACK_MASK))),
542 				msp->registers + MSP_GCR);
543 
544 		disable_msp_tx(msp);
545 		disable_msp_rx(msp);
546 	} else if (disable_tx)
547 		disable_msp_tx(msp);
548 	else if (disable_rx)
549 		disable_msp_rx(msp);
550 
551 	return 0;
552 }
553 
554 int ux500_msp_i2s_trigger(struct ux500_msp *msp, int cmd, int direction)
555 {
556 	u32 reg_val_GCR, enable_bit;
557 
558 	if (msp->msp_state == MSP_STATE_IDLE) {
559 		dev_err(msp->dev, "%s: ERROR: MSP is not configured!\n",
560 			__func__);
561 		return -EINVAL;
562 	}
563 
564 	switch (cmd) {
565 	case SNDRV_PCM_TRIGGER_START:
566 	case SNDRV_PCM_TRIGGER_RESUME:
567 	case SNDRV_PCM_TRIGGER_PAUSE_RELEASE:
568 		if (direction == SNDRV_PCM_STREAM_PLAYBACK)
569 			enable_bit = TX_ENABLE;
570 		else
571 			enable_bit = RX_ENABLE;
572 		reg_val_GCR = readl(msp->registers + MSP_GCR);
573 		writel(reg_val_GCR | enable_bit, msp->registers + MSP_GCR);
574 		break;
575 
576 	case SNDRV_PCM_TRIGGER_STOP:
577 	case SNDRV_PCM_TRIGGER_SUSPEND:
578 	case SNDRV_PCM_TRIGGER_PAUSE_PUSH:
579 		if (direction == SNDRV_PCM_STREAM_PLAYBACK)
580 			disable_msp_tx(msp);
581 		else
582 			disable_msp_rx(msp);
583 		break;
584 	default:
585 		return -EINVAL;
586 	}
587 
588 	return 0;
589 }
590 
591 int ux500_msp_i2s_close(struct ux500_msp *msp, unsigned int dir)
592 {
593 	int status = 0;
594 
595 	dev_dbg(msp->dev, "%s: Enter (dir = 0x%01x).\n", __func__, dir);
596 
597 	status = disable_msp(msp, dir);
598 	if (msp->dir_busy == 0) {
599 		/* disable sample rate and frame generators */
600 		msp->msp_state = MSP_STATE_IDLE;
601 		writel((readl(msp->registers + MSP_GCR) &
602 			       (~(FRAME_GEN_ENABLE | SRG_ENABLE))),
603 			      msp->registers + MSP_GCR);
604 
605 		writel(0, msp->registers + MSP_GCR);
606 		writel(0, msp->registers + MSP_TCF);
607 		writel(0, msp->registers + MSP_RCF);
608 		writel(0, msp->registers + MSP_DMACR);
609 		writel(0, msp->registers + MSP_SRG);
610 		writel(0, msp->registers + MSP_MCR);
611 		writel(0, msp->registers + MSP_RCM);
612 		writel(0, msp->registers + MSP_RCV);
613 		writel(0, msp->registers + MSP_TCE0);
614 		writel(0, msp->registers + MSP_TCE1);
615 		writel(0, msp->registers + MSP_TCE2);
616 		writel(0, msp->registers + MSP_TCE3);
617 		writel(0, msp->registers + MSP_RCE0);
618 		writel(0, msp->registers + MSP_RCE1);
619 		writel(0, msp->registers + MSP_RCE2);
620 		writel(0, msp->registers + MSP_RCE3);
621 	}
622 
623 	return status;
624 
625 }
626 
627 int ux500_msp_i2s_init_msp(struct platform_device *pdev,
628 			struct ux500_msp **msp_p)
629 {
630 	struct resource *res = NULL;
631 	struct ux500_msp *msp;
632 
633 	*msp_p = devm_kzalloc(&pdev->dev, sizeof(struct ux500_msp), GFP_KERNEL);
634 	msp = *msp_p;
635 	if (!msp)
636 		return -ENOMEM;
637 
638 	msp->dev = &pdev->dev;
639 
640 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
641 	if (res == NULL) {
642 		dev_err(&pdev->dev, "%s: ERROR: Unable to get resource!\n",
643 			__func__);
644 		return -ENOMEM;
645 	}
646 
647 	msp->tx_rx_addr = res->start + MSP_DR;
648 	msp->registers = devm_ioremap(&pdev->dev, res->start,
649 				      resource_size(res));
650 	if (msp->registers == NULL) {
651 		dev_err(&pdev->dev, "%s: ERROR: ioremap failed!\n", __func__);
652 		return -ENOMEM;
653 	}
654 
655 	msp->msp_state = MSP_STATE_IDLE;
656 	msp->loopback_enable = 0;
657 
658 	return 0;
659 }
660 
661 void ux500_msp_i2s_cleanup_msp(struct platform_device *pdev,
662 			struct ux500_msp *msp)
663 {
664 	dev_dbg(msp->dev, "%s: Enter (id = %d).\n", __func__, msp->id);
665 }
666 
667 MODULE_LICENSE("GPL v2");
668