1 // SPDX-License-Identifier: GPL-2.0 2 // 3 // Freescale SSI ALSA SoC Digital Audio Interface (DAI) driver 4 // 5 // Author: Timur Tabi <timur@freescale.com> 6 // 7 // Copyright 2007-2010 Freescale Semiconductor, Inc. 8 // 9 // Some notes why imx-pcm-fiq is used instead of DMA on some boards: 10 // 11 // The i.MX SSI core has some nasty limitations in AC97 mode. While most 12 // sane processor vendors have a FIFO per AC97 slot, the i.MX has only 13 // one FIFO which combines all valid receive slots. We cannot even select 14 // which slots we want to receive. The WM9712 with which this driver 15 // was developed with always sends GPIO status data in slot 12 which 16 // we receive in our (PCM-) data stream. The only chance we have is to 17 // manually skip this data in the FIQ handler. With sampling rates different 18 // from 48000Hz not every frame has valid receive data, so the ratio 19 // between pcm data and GPIO status data changes. Our FIQ handler is not 20 // able to handle this, hence this driver only works with 48000Hz sampling 21 // rate. 22 // Reading and writing AC97 registers is another challenge. The core 23 // provides us status bits when the read register is updated with *another* 24 // value. When we read the same register two times (and the register still 25 // contains the same value) these status bits are not set. We work 26 // around this by not polling these bits but only wait a fixed delay. 27 28 #include <linux/init.h> 29 #include <linux/io.h> 30 #include <linux/module.h> 31 #include <linux/interrupt.h> 32 #include <linux/clk.h> 33 #include <linux/ctype.h> 34 #include <linux/device.h> 35 #include <linux/delay.h> 36 #include <linux/mutex.h> 37 #include <linux/slab.h> 38 #include <linux/spinlock.h> 39 #include <linux/of.h> 40 #include <linux/of_address.h> 41 #include <linux/of_irq.h> 42 #include <linux/of_platform.h> 43 #include <linux/dma/imx-dma.h> 44 45 #include <sound/core.h> 46 #include <sound/pcm.h> 47 #include <sound/pcm_params.h> 48 #include <sound/initval.h> 49 #include <sound/soc.h> 50 #include <sound/dmaengine_pcm.h> 51 52 #include "fsl_ssi.h" 53 #include "imx-pcm.h" 54 55 /* Define RX and TX to index ssi->regvals array; Can be 0 or 1 only */ 56 #define RX 0 57 #define TX 1 58 59 /** 60 * FSLSSI_I2S_FORMATS: audio formats supported by the SSI 61 * 62 * The SSI has a limitation in that the samples must be in the same byte 63 * order as the host CPU. This is because when multiple bytes are written 64 * to the STX register, the bytes and bits must be written in the same 65 * order. The STX is a shift register, so all the bits need to be aligned 66 * (bit-endianness must match byte-endianness). Processors typically write 67 * the bits within a byte in the same order that the bytes of a word are 68 * written in. So if the host CPU is big-endian, then only big-endian 69 * samples will be written to STX properly. 70 */ 71 #ifdef __BIG_ENDIAN 72 #define FSLSSI_I2S_FORMATS \ 73 (SNDRV_PCM_FMTBIT_S8 | \ 74 SNDRV_PCM_FMTBIT_S16_BE | \ 75 SNDRV_PCM_FMTBIT_S18_3BE | \ 76 SNDRV_PCM_FMTBIT_S20_3BE | \ 77 SNDRV_PCM_FMTBIT_S24_3BE | \ 78 SNDRV_PCM_FMTBIT_S24_BE) 79 #else 80 #define FSLSSI_I2S_FORMATS \ 81 (SNDRV_PCM_FMTBIT_S8 | \ 82 SNDRV_PCM_FMTBIT_S16_LE | \ 83 SNDRV_PCM_FMTBIT_S18_3LE | \ 84 SNDRV_PCM_FMTBIT_S20_3LE | \ 85 SNDRV_PCM_FMTBIT_S24_3LE | \ 86 SNDRV_PCM_FMTBIT_S24_LE) 87 #endif 88 89 /* 90 * In AC97 mode, TXDIR bit is forced to 0 and TFDIR bit is forced to 1: 91 * - SSI inputs external bit clock and outputs frame sync clock -- CBM_CFS 92 * - Also have NB_NF to mark these two clocks will not be inverted 93 */ 94 #define FSLSSI_AC97_DAIFMT \ 95 (SND_SOC_DAIFMT_AC97 | \ 96 SND_SOC_DAIFMT_BC_FP | \ 97 SND_SOC_DAIFMT_NB_NF) 98 99 #define FSLSSI_SIER_DBG_RX_FLAGS \ 100 (SSI_SIER_RFF0_EN | \ 101 SSI_SIER_RLS_EN | \ 102 SSI_SIER_RFS_EN | \ 103 SSI_SIER_ROE0_EN | \ 104 SSI_SIER_RFRC_EN) 105 #define FSLSSI_SIER_DBG_TX_FLAGS \ 106 (SSI_SIER_TFE0_EN | \ 107 SSI_SIER_TLS_EN | \ 108 SSI_SIER_TFS_EN | \ 109 SSI_SIER_TUE0_EN | \ 110 SSI_SIER_TFRC_EN) 111 112 enum fsl_ssi_type { 113 FSL_SSI_MCP8610, 114 FSL_SSI_MX21, 115 FSL_SSI_MX35, 116 FSL_SSI_MX51, 117 }; 118 119 struct fsl_ssi_regvals { 120 u32 sier; 121 u32 srcr; 122 u32 stcr; 123 u32 scr; 124 }; 125 126 static bool fsl_ssi_readable_reg(struct device *dev, unsigned int reg) 127 { 128 switch (reg) { 129 case REG_SSI_SACCEN: 130 case REG_SSI_SACCDIS: 131 return false; 132 default: 133 return true; 134 } 135 } 136 137 static bool fsl_ssi_volatile_reg(struct device *dev, unsigned int reg) 138 { 139 switch (reg) { 140 case REG_SSI_STX0: 141 case REG_SSI_STX1: 142 case REG_SSI_SRX0: 143 case REG_SSI_SRX1: 144 case REG_SSI_SISR: 145 case REG_SSI_SFCSR: 146 case REG_SSI_SACNT: 147 case REG_SSI_SACADD: 148 case REG_SSI_SACDAT: 149 case REG_SSI_SATAG: 150 case REG_SSI_SACCST: 151 case REG_SSI_SOR: 152 return true; 153 default: 154 return false; 155 } 156 } 157 158 static bool fsl_ssi_precious_reg(struct device *dev, unsigned int reg) 159 { 160 switch (reg) { 161 case REG_SSI_SRX0: 162 case REG_SSI_SRX1: 163 case REG_SSI_SISR: 164 case REG_SSI_SACADD: 165 case REG_SSI_SACDAT: 166 case REG_SSI_SATAG: 167 return true; 168 default: 169 return false; 170 } 171 } 172 173 static bool fsl_ssi_writeable_reg(struct device *dev, unsigned int reg) 174 { 175 switch (reg) { 176 case REG_SSI_SRX0: 177 case REG_SSI_SRX1: 178 case REG_SSI_SACCST: 179 return false; 180 default: 181 return true; 182 } 183 } 184 185 static const struct regmap_config fsl_ssi_regconfig = { 186 .max_register = REG_SSI_SACCDIS, 187 .reg_bits = 32, 188 .val_bits = 32, 189 .reg_stride = 4, 190 .val_format_endian = REGMAP_ENDIAN_NATIVE, 191 .num_reg_defaults_raw = REG_SSI_SACCDIS / sizeof(uint32_t) + 1, 192 .readable_reg = fsl_ssi_readable_reg, 193 .volatile_reg = fsl_ssi_volatile_reg, 194 .precious_reg = fsl_ssi_precious_reg, 195 .writeable_reg = fsl_ssi_writeable_reg, 196 .cache_type = REGCACHE_FLAT, 197 }; 198 199 struct fsl_ssi_soc_data { 200 bool imx; 201 bool imx21regs; /* imx21-class SSI - no SACC{ST,EN,DIS} regs */ 202 bool offline_config; 203 u32 sisr_write_mask; 204 }; 205 206 /** 207 * struct fsl_ssi - per-SSI private data 208 * @regs: Pointer to the regmap registers 209 * @irq: IRQ of this SSI 210 * @cpu_dai_drv: CPU DAI driver for this device 211 * @dai_fmt: DAI configuration this device is currently used with 212 * @streams: Mask of current active streams: BIT(TX) and BIT(RX) 213 * @i2s_net: I2S and Network mode configurations of SCR register 214 * (this is the initial settings based on the DAI format) 215 * @synchronous: Use synchronous mode - both of TX and RX use STCK and SFCK 216 * @use_dma: DMA is used or FIQ with stream filter 217 * @use_dual_fifo: DMA with support for dual FIFO mode 218 * @use_dyna_fifo: DMA with support for multi FIFO script 219 * @has_ipg_clk_name: If "ipg" is in the clock name list of device tree 220 * @fifo_depth: Depth of the SSI FIFOs 221 * @slot_width: Width of each DAI slot 222 * @slots: Number of slots 223 * @regvals: Specific RX/TX register settings 224 * @clk: Clock source to access register 225 * @baudclk: Clock source to generate bit and frame-sync clocks 226 * @baudclk_streams: Active streams that are using baudclk 227 * @regcache_sfcsr: Cache sfcsr register value during suspend and resume 228 * @regcache_sacnt: Cache sacnt register value during suspend and resume 229 * @dma_params_tx: DMA transmit parameters 230 * @dma_params_rx: DMA receive parameters 231 * @ssi_phys: physical address of the SSI registers 232 * @fiq_params: FIQ stream filtering parameters 233 * @card_pdev: Platform_device pointer to register a sound card for PowerPC or 234 * to register a CODEC platform device for AC97 235 * @card_name: Platform_device name to register a sound card for PowerPC or 236 * to register a CODEC platform device for AC97 237 * @card_idx: The index of SSI to register a sound card for PowerPC or 238 * to register a CODEC platform device for AC97 239 * @dbg_stats: Debugging statistics 240 * @soc: SoC specific data 241 * @dev: Pointer to &pdev->dev 242 * @fifo_watermark: The FIFO watermark setting. Notifies DMA when there are 243 * @fifo_watermark or fewer words in TX fifo or 244 * @fifo_watermark or more empty words in RX fifo. 245 * @dma_maxburst: Max number of words to transfer in one go. So far, 246 * this is always the same as fifo_watermark. 247 * @ac97_reg_lock: Mutex lock to serialize AC97 register access operations 248 * @audio_config: configure for dma multi fifo script 249 */ 250 struct fsl_ssi { 251 struct regmap *regs; 252 int irq; 253 struct snd_soc_dai_driver cpu_dai_drv; 254 255 unsigned int dai_fmt; 256 u8 streams; 257 u8 i2s_net; 258 bool synchronous; 259 bool use_dma; 260 bool use_dual_fifo; 261 bool use_dyna_fifo; 262 bool has_ipg_clk_name; 263 unsigned int fifo_depth; 264 unsigned int slot_width; 265 unsigned int slots; 266 struct fsl_ssi_regvals regvals[2]; 267 268 struct clk *clk; 269 struct clk *baudclk; 270 unsigned int baudclk_streams; 271 272 u32 regcache_sfcsr; 273 u32 regcache_sacnt; 274 275 struct snd_dmaengine_dai_dma_data dma_params_tx; 276 struct snd_dmaengine_dai_dma_data dma_params_rx; 277 dma_addr_t ssi_phys; 278 279 struct imx_pcm_fiq_params fiq_params; 280 281 struct platform_device *card_pdev; 282 char card_name[32]; 283 u32 card_idx; 284 285 struct fsl_ssi_dbg dbg_stats; 286 287 const struct fsl_ssi_soc_data *soc; 288 struct device *dev; 289 290 u32 fifo_watermark; 291 u32 dma_maxburst; 292 293 struct mutex ac97_reg_lock; 294 struct sdma_peripheral_config audio_config[2]; 295 }; 296 297 /* 298 * SoC specific data 299 * 300 * Notes: 301 * 1) SSI in earlier SoCS has critical bits in control registers that 302 * cannot be changed after SSI starts running -- a software reset 303 * (set SSIEN to 0) is required to change their values. So adding 304 * an offline_config flag for these SoCs. 305 * 2) SDMA is available since imx35. However, imx35 does not support 306 * DMA bits changing when SSI is running, so set offline_config. 307 * 3) imx51 and later versions support register configurations when 308 * SSI is running (SSIEN); For these versions, DMA needs to be 309 * configured before SSI sends DMA request to avoid an undefined 310 * DMA request on the SDMA side. 311 */ 312 313 static struct fsl_ssi_soc_data fsl_ssi_mpc8610 = { 314 .imx = false, 315 .offline_config = true, 316 .sisr_write_mask = SSI_SISR_RFRC | SSI_SISR_TFRC | 317 SSI_SISR_ROE0 | SSI_SISR_ROE1 | 318 SSI_SISR_TUE0 | SSI_SISR_TUE1, 319 }; 320 321 static struct fsl_ssi_soc_data fsl_ssi_imx21 = { 322 .imx = true, 323 .imx21regs = true, 324 .offline_config = true, 325 .sisr_write_mask = 0, 326 }; 327 328 static struct fsl_ssi_soc_data fsl_ssi_imx35 = { 329 .imx = true, 330 .offline_config = true, 331 .sisr_write_mask = SSI_SISR_RFRC | SSI_SISR_TFRC | 332 SSI_SISR_ROE0 | SSI_SISR_ROE1 | 333 SSI_SISR_TUE0 | SSI_SISR_TUE1, 334 }; 335 336 static struct fsl_ssi_soc_data fsl_ssi_imx51 = { 337 .imx = true, 338 .offline_config = false, 339 .sisr_write_mask = SSI_SISR_ROE0 | SSI_SISR_ROE1 | 340 SSI_SISR_TUE0 | SSI_SISR_TUE1, 341 }; 342 343 static const struct of_device_id fsl_ssi_ids[] = { 344 { .compatible = "fsl,mpc8610-ssi", .data = &fsl_ssi_mpc8610 }, 345 { .compatible = "fsl,imx51-ssi", .data = &fsl_ssi_imx51 }, 346 { .compatible = "fsl,imx35-ssi", .data = &fsl_ssi_imx35 }, 347 { .compatible = "fsl,imx21-ssi", .data = &fsl_ssi_imx21 }, 348 {} 349 }; 350 MODULE_DEVICE_TABLE(of, fsl_ssi_ids); 351 352 static bool fsl_ssi_is_ac97(struct fsl_ssi *ssi) 353 { 354 return (ssi->dai_fmt & SND_SOC_DAIFMT_FORMAT_MASK) == 355 SND_SOC_DAIFMT_AC97; 356 } 357 358 static bool fsl_ssi_is_i2s_clock_provider(struct fsl_ssi *ssi) 359 { 360 return (ssi->dai_fmt & SND_SOC_DAIFMT_CLOCK_PROVIDER_MASK) == 361 SND_SOC_DAIFMT_BP_FP; 362 } 363 364 static bool fsl_ssi_is_i2s_bc_fp(struct fsl_ssi *ssi) 365 { 366 return (ssi->dai_fmt & SND_SOC_DAIFMT_CLOCK_PROVIDER_MASK) == 367 SND_SOC_DAIFMT_BC_FP; 368 } 369 370 /** 371 * fsl_ssi_isr - Interrupt handler to gather states 372 * @irq: irq number 373 * @dev_id: context 374 */ 375 static irqreturn_t fsl_ssi_isr(int irq, void *dev_id) 376 { 377 struct fsl_ssi *ssi = dev_id; 378 struct regmap *regs = ssi->regs; 379 u32 sisr, sisr2; 380 381 regmap_read(regs, REG_SSI_SISR, &sisr); 382 383 sisr2 = sisr & ssi->soc->sisr_write_mask; 384 /* Clear the bits that we set */ 385 if (sisr2) 386 regmap_write(regs, REG_SSI_SISR, sisr2); 387 388 fsl_ssi_dbg_isr(&ssi->dbg_stats, sisr); 389 390 return IRQ_HANDLED; 391 } 392 393 /** 394 * fsl_ssi_config_enable - Set SCR, SIER, STCR and SRCR registers with 395 * cached values in regvals 396 * @ssi: SSI context 397 * @tx: direction 398 * 399 * Notes: 400 * 1) For offline_config SoCs, enable all necessary bits of both streams 401 * when 1st stream starts, even if the opposite stream will not start 402 * 2) It also clears FIFO before setting regvals; SOR is safe to set online 403 */ 404 static void fsl_ssi_config_enable(struct fsl_ssi *ssi, bool tx) 405 { 406 struct fsl_ssi_regvals *vals = ssi->regvals; 407 int dir = tx ? TX : RX; 408 u32 sier, srcr, stcr; 409 410 /* Clear dirty data in the FIFO; It also prevents channel slipping */ 411 regmap_update_bits(ssi->regs, REG_SSI_SOR, 412 SSI_SOR_xX_CLR(tx), SSI_SOR_xX_CLR(tx)); 413 414 /* 415 * On offline_config SoCs, SxCR and SIER are already configured when 416 * the previous stream started. So skip all SxCR and SIER settings 417 * to prevent online reconfigurations, then jump to set SCR directly 418 */ 419 if (ssi->soc->offline_config && ssi->streams) 420 goto enable_scr; 421 422 if (ssi->soc->offline_config) { 423 /* 424 * Online reconfiguration not supported, so enable all bits for 425 * both streams at once to avoid necessity of reconfigurations 426 */ 427 srcr = vals[RX].srcr | vals[TX].srcr; 428 stcr = vals[RX].stcr | vals[TX].stcr; 429 sier = vals[RX].sier | vals[TX].sier; 430 } else { 431 /* Otherwise, only set bits for the current stream */ 432 srcr = vals[dir].srcr; 433 stcr = vals[dir].stcr; 434 sier = vals[dir].sier; 435 } 436 437 /* Configure SRCR, STCR and SIER at once */ 438 regmap_update_bits(ssi->regs, REG_SSI_SRCR, srcr, srcr); 439 regmap_update_bits(ssi->regs, REG_SSI_STCR, stcr, stcr); 440 regmap_update_bits(ssi->regs, REG_SSI_SIER, sier, sier); 441 442 enable_scr: 443 /* 444 * Start DMA before setting TE to avoid FIFO underrun 445 * which may cause a channel slip or a channel swap 446 * 447 * TODO: FIQ cases might also need this upon testing 448 */ 449 if (ssi->use_dma && tx) { 450 int try = 100; 451 u32 sfcsr; 452 453 /* Enable SSI first to send TX DMA request */ 454 regmap_update_bits(ssi->regs, REG_SSI_SCR, 455 SSI_SCR_SSIEN, SSI_SCR_SSIEN); 456 457 /* Busy wait until TX FIFO not empty -- DMA working */ 458 do { 459 regmap_read(ssi->regs, REG_SSI_SFCSR, &sfcsr); 460 if (SSI_SFCSR_TFCNT0(sfcsr)) 461 break; 462 } while (--try); 463 464 /* FIFO still empty -- something might be wrong */ 465 if (!SSI_SFCSR_TFCNT0(sfcsr)) 466 dev_warn(ssi->dev, "Timeout waiting TX FIFO filling\n"); 467 } 468 /* Enable all remaining bits in SCR */ 469 regmap_update_bits(ssi->regs, REG_SSI_SCR, 470 vals[dir].scr, vals[dir].scr); 471 472 /* Log the enabled stream to the mask */ 473 ssi->streams |= BIT(dir); 474 } 475 476 /* 477 * Exclude bits that are used by the opposite stream 478 * 479 * When both streams are active, disabling some bits for the current stream 480 * might break the other stream if these bits are used by it. 481 * 482 * @vals : regvals of the current stream 483 * @avals: regvals of the opposite stream 484 * @aactive: active state of the opposite stream 485 * 486 * 1) XOR vals and avals to get the differences if the other stream is active; 487 * Otherwise, return current vals if the other stream is not active 488 * 2) AND the result of 1) with the current vals 489 */ 490 #define _ssi_xor_shared_bits(vals, avals, aactive) \ 491 ((vals) ^ ((avals) * (aactive))) 492 493 #define ssi_excl_shared_bits(vals, avals, aactive) \ 494 ((vals) & _ssi_xor_shared_bits(vals, avals, aactive)) 495 496 /** 497 * fsl_ssi_config_disable - Unset SCR, SIER, STCR and SRCR registers 498 * with cached values in regvals 499 * @ssi: SSI context 500 * @tx: direction 501 * 502 * Notes: 503 * 1) For offline_config SoCs, to avoid online reconfigurations, disable all 504 * bits of both streams at once when the last stream is abort to end 505 * 2) It also clears FIFO after unsetting regvals; SOR is safe to set online 506 */ 507 static void fsl_ssi_config_disable(struct fsl_ssi *ssi, bool tx) 508 { 509 struct fsl_ssi_regvals *vals, *avals; 510 u32 sier, srcr, stcr, scr; 511 int adir = tx ? RX : TX; 512 int dir = tx ? TX : RX; 513 bool aactive; 514 515 /* Check if the opposite stream is active */ 516 aactive = ssi->streams & BIT(adir); 517 518 vals = &ssi->regvals[dir]; 519 520 /* Get regvals of the opposite stream to keep opposite stream safe */ 521 avals = &ssi->regvals[adir]; 522 523 /* 524 * To keep the other stream safe, exclude shared bits between 525 * both streams, and get safe bits to disable current stream 526 */ 527 scr = ssi_excl_shared_bits(vals->scr, avals->scr, aactive); 528 529 /* Disable safe bits of SCR register for the current stream */ 530 regmap_update_bits(ssi->regs, REG_SSI_SCR, scr, 0); 531 532 /* Log the disabled stream to the mask */ 533 ssi->streams &= ~BIT(dir); 534 535 /* 536 * On offline_config SoCs, if the other stream is active, skip 537 * SxCR and SIER settings to prevent online reconfigurations 538 */ 539 if (ssi->soc->offline_config && aactive) 540 goto fifo_clear; 541 542 if (ssi->soc->offline_config) { 543 /* Now there is only current stream active, disable all bits */ 544 srcr = vals->srcr | avals->srcr; 545 stcr = vals->stcr | avals->stcr; 546 sier = vals->sier | avals->sier; 547 } else { 548 /* 549 * To keep the other stream safe, exclude shared bits between 550 * both streams, and get safe bits to disable current stream 551 */ 552 sier = ssi_excl_shared_bits(vals->sier, avals->sier, aactive); 553 srcr = ssi_excl_shared_bits(vals->srcr, avals->srcr, aactive); 554 stcr = ssi_excl_shared_bits(vals->stcr, avals->stcr, aactive); 555 } 556 557 /* Clear configurations of SRCR, STCR and SIER at once */ 558 regmap_update_bits(ssi->regs, REG_SSI_SRCR, srcr, 0); 559 regmap_update_bits(ssi->regs, REG_SSI_STCR, stcr, 0); 560 regmap_update_bits(ssi->regs, REG_SSI_SIER, sier, 0); 561 562 fifo_clear: 563 /* Clear remaining data in the FIFO */ 564 regmap_update_bits(ssi->regs, REG_SSI_SOR, 565 SSI_SOR_xX_CLR(tx), SSI_SOR_xX_CLR(tx)); 566 } 567 568 static void fsl_ssi_tx_ac97_saccst_setup(struct fsl_ssi *ssi) 569 { 570 struct regmap *regs = ssi->regs; 571 572 /* no SACC{ST,EN,DIS} regs on imx21-class SSI */ 573 if (!ssi->soc->imx21regs) { 574 /* Disable all channel slots */ 575 regmap_write(regs, REG_SSI_SACCDIS, 0xff); 576 /* Enable slots 3 & 4 -- PCM Playback Left & Right channels */ 577 regmap_write(regs, REG_SSI_SACCEN, 0x300); 578 } 579 } 580 581 /** 582 * fsl_ssi_setup_regvals - Cache critical bits of SIER, SRCR, STCR and 583 * SCR to later set them safely 584 * @ssi: SSI context 585 */ 586 static void fsl_ssi_setup_regvals(struct fsl_ssi *ssi) 587 { 588 struct fsl_ssi_regvals *vals = ssi->regvals; 589 590 vals[RX].sier = SSI_SIER_RFF0_EN | FSLSSI_SIER_DBG_RX_FLAGS; 591 vals[RX].srcr = SSI_SRCR_RFEN0; 592 vals[RX].scr = SSI_SCR_SSIEN | SSI_SCR_RE; 593 vals[TX].sier = SSI_SIER_TFE0_EN | FSLSSI_SIER_DBG_TX_FLAGS; 594 vals[TX].stcr = SSI_STCR_TFEN0; 595 vals[TX].scr = SSI_SCR_SSIEN | SSI_SCR_TE; 596 597 /* AC97 has already enabled SSIEN, RE and TE, so ignore them */ 598 if (fsl_ssi_is_ac97(ssi)) 599 vals[RX].scr = vals[TX].scr = 0; 600 601 if (ssi->use_dual_fifo) { 602 vals[RX].srcr |= SSI_SRCR_RFEN1; 603 vals[TX].stcr |= SSI_STCR_TFEN1; 604 } 605 606 if (ssi->use_dma) { 607 vals[RX].sier |= SSI_SIER_RDMAE; 608 vals[TX].sier |= SSI_SIER_TDMAE; 609 } else { 610 vals[RX].sier |= SSI_SIER_RIE; 611 vals[TX].sier |= SSI_SIER_TIE; 612 } 613 } 614 615 static void fsl_ssi_setup_ac97(struct fsl_ssi *ssi) 616 { 617 struct regmap *regs = ssi->regs; 618 619 /* Setup the clock control register */ 620 regmap_write(regs, REG_SSI_STCCR, SSI_SxCCR_WL(17) | SSI_SxCCR_DC(13)); 621 regmap_write(regs, REG_SSI_SRCCR, SSI_SxCCR_WL(17) | SSI_SxCCR_DC(13)); 622 623 /* Enable AC97 mode and startup the SSI */ 624 regmap_write(regs, REG_SSI_SACNT, SSI_SACNT_AC97EN | SSI_SACNT_FV); 625 626 /* AC97 has to communicate with codec before starting a stream */ 627 regmap_update_bits(regs, REG_SSI_SCR, 628 SSI_SCR_SSIEN | SSI_SCR_TE | SSI_SCR_RE, 629 SSI_SCR_SSIEN | SSI_SCR_TE | SSI_SCR_RE); 630 631 regmap_write(regs, REG_SSI_SOR, SSI_SOR_WAIT(3)); 632 } 633 634 static int fsl_ssi_startup(struct snd_pcm_substream *substream, 635 struct snd_soc_dai *dai) 636 { 637 struct snd_soc_pcm_runtime *rtd = snd_soc_substream_to_rtd(substream); 638 struct fsl_ssi *ssi = snd_soc_dai_get_drvdata(snd_soc_rtd_to_cpu(rtd, 0)); 639 int ret; 640 641 ret = clk_prepare_enable(ssi->clk); 642 if (ret) 643 return ret; 644 645 /* 646 * When using dual fifo mode, it is safer to ensure an even period 647 * size. If appearing to an odd number while DMA always starts its 648 * task from fifo0, fifo1 would be neglected at the end of each 649 * period. But SSI would still access fifo1 with an invalid data. 650 */ 651 if (ssi->use_dual_fifo || ssi->use_dyna_fifo) 652 snd_pcm_hw_constraint_step(substream->runtime, 0, 653 SNDRV_PCM_HW_PARAM_PERIOD_SIZE, 2); 654 655 return 0; 656 } 657 658 static void fsl_ssi_shutdown(struct snd_pcm_substream *substream, 659 struct snd_soc_dai *dai) 660 { 661 struct snd_soc_pcm_runtime *rtd = snd_soc_substream_to_rtd(substream); 662 struct fsl_ssi *ssi = snd_soc_dai_get_drvdata(snd_soc_rtd_to_cpu(rtd, 0)); 663 664 clk_disable_unprepare(ssi->clk); 665 } 666 667 /** 668 * fsl_ssi_set_bclk - Configure Digital Audio Interface bit clock 669 * @substream: ASoC substream 670 * @dai: pointer to DAI 671 * @hw_params: pointers to hw_params 672 * 673 * Notes: This function can be only called when using SSI as DAI master 674 * 675 * Quick instruction for parameters: 676 * freq: Output BCLK frequency = samplerate * slots * slot_width 677 * (In 2-channel I2S Master mode, slot_width is fixed 32) 678 */ 679 static int fsl_ssi_set_bclk(struct snd_pcm_substream *substream, 680 struct snd_soc_dai *dai, 681 struct snd_pcm_hw_params *hw_params) 682 { 683 bool tx2, tx = substream->stream == SNDRV_PCM_STREAM_PLAYBACK; 684 struct fsl_ssi *ssi = snd_soc_dai_get_drvdata(dai); 685 struct regmap *regs = ssi->regs; 686 u32 pm = 999, div2, psr, stccr, mask, afreq, factor, i; 687 unsigned long clkrate, baudrate, tmprate; 688 unsigned int channels = params_channels(hw_params); 689 unsigned int slot_width = params_width(hw_params); 690 unsigned int slots = 2; 691 u64 sub, savesub = 100000; 692 unsigned int freq; 693 bool baudclk_is_used; 694 int ret; 695 696 /* Override slots and slot_width if being specifically set... */ 697 if (ssi->slots) 698 slots = ssi->slots; 699 if (ssi->slot_width) 700 slot_width = ssi->slot_width; 701 702 /* ...but force 32 bits for stereo audio using I2S Master Mode */ 703 if (channels == 2 && 704 (ssi->i2s_net & SSI_SCR_I2S_MODE_MASK) == SSI_SCR_I2S_MODE_MASTER) 705 slot_width = 32; 706 707 /* Generate bit clock based on the slot number and slot width */ 708 freq = slots * slot_width * params_rate(hw_params); 709 710 /* Don't apply it to any non-baudclk circumstance */ 711 if (IS_ERR(ssi->baudclk)) 712 return -EINVAL; 713 714 /* 715 * Hardware limitation: The bclk rate must be 716 * never greater than 1/5 IPG clock rate 717 */ 718 if (freq * 5 > clk_get_rate(ssi->clk)) { 719 dev_err(dai->dev, "bitclk > ipgclk / 5\n"); 720 return -EINVAL; 721 } 722 723 baudclk_is_used = ssi->baudclk_streams & ~(BIT(substream->stream)); 724 725 /* It should be already enough to divide clock by setting pm alone */ 726 psr = 0; 727 div2 = 0; 728 729 factor = (div2 + 1) * (7 * psr + 1) * 2; 730 731 for (i = 0; i < 255; i++) { 732 tmprate = freq * factor * (i + 1); 733 734 if (baudclk_is_used) 735 clkrate = clk_get_rate(ssi->baudclk); 736 else 737 clkrate = clk_round_rate(ssi->baudclk, tmprate); 738 739 clkrate /= factor; 740 afreq = clkrate / (i + 1); 741 742 if (freq == afreq) 743 sub = 0; 744 else if (freq / afreq == 1) 745 sub = freq - afreq; 746 else if (afreq / freq == 1) 747 sub = afreq - freq; 748 else 749 continue; 750 751 /* Calculate the fraction */ 752 sub *= 100000; 753 do_div(sub, freq); 754 755 if (sub < savesub && !(i == 0)) { 756 baudrate = tmprate; 757 savesub = sub; 758 pm = i; 759 } 760 761 /* We are lucky */ 762 if (savesub == 0) 763 break; 764 } 765 766 /* No proper pm found if it is still remaining the initial value */ 767 if (pm == 999) { 768 dev_err(dai->dev, "failed to handle the required sysclk\n"); 769 return -EINVAL; 770 } 771 772 stccr = SSI_SxCCR_PM(pm + 1); 773 mask = SSI_SxCCR_PM_MASK | SSI_SxCCR_DIV2 | SSI_SxCCR_PSR; 774 775 /* STCCR is used for RX in synchronous mode */ 776 tx2 = tx || ssi->synchronous; 777 regmap_update_bits(regs, REG_SSI_SxCCR(tx2), mask, stccr); 778 779 if (!baudclk_is_used) { 780 ret = clk_set_rate(ssi->baudclk, baudrate); 781 if (ret) { 782 dev_err(dai->dev, "failed to set baudclk rate\n"); 783 return -EINVAL; 784 } 785 } 786 787 return 0; 788 } 789 790 /** 791 * fsl_ssi_hw_params - Configure SSI based on PCM hardware parameters 792 * @substream: ASoC substream 793 * @hw_params: pointers to hw_params 794 * @dai: pointer to DAI 795 * 796 * Notes: 797 * 1) SxCCR.WL bits are critical bits that require SSI to be temporarily 798 * disabled on offline_config SoCs. Even for online configurable SoCs 799 * running in synchronous mode (both TX and RX use STCCR), it is not 800 * safe to re-configure them when both two streams start running. 801 * 2) SxCCR.PM, SxCCR.DIV2 and SxCCR.PSR bits will be configured in the 802 * fsl_ssi_set_bclk() if SSI is the DAI clock master. 803 */ 804 static int fsl_ssi_hw_params(struct snd_pcm_substream *substream, 805 struct snd_pcm_hw_params *hw_params, 806 struct snd_soc_dai *dai) 807 { 808 bool tx2, tx = substream->stream == SNDRV_PCM_STREAM_PLAYBACK; 809 struct fsl_ssi *ssi = snd_soc_dai_get_drvdata(dai); 810 struct fsl_ssi_regvals *vals = ssi->regvals; 811 struct regmap *regs = ssi->regs; 812 unsigned int channels = params_channels(hw_params); 813 unsigned int sample_size = params_width(hw_params); 814 u32 wl = SSI_SxCCR_WL(sample_size); 815 int ret; 816 817 if (fsl_ssi_is_i2s_clock_provider(ssi)) { 818 ret = fsl_ssi_set_bclk(substream, dai, hw_params); 819 if (ret) 820 return ret; 821 822 /* Do not enable the clock if it is already enabled */ 823 if (!(ssi->baudclk_streams & BIT(substream->stream))) { 824 ret = clk_prepare_enable(ssi->baudclk); 825 if (ret) 826 return ret; 827 828 ssi->baudclk_streams |= BIT(substream->stream); 829 } 830 } 831 832 /* 833 * SSI is properly configured if it is enabled and running in 834 * the synchronous mode; Note that AC97 mode is an exception 835 * that should set separate configurations for STCCR and SRCCR 836 * despite running in the synchronous mode. 837 */ 838 if (ssi->streams && ssi->synchronous) 839 return 0; 840 841 if (!fsl_ssi_is_ac97(ssi)) { 842 /* 843 * Keep the ssi->i2s_net intact while having a local variable 844 * to override settings for special use cases. Otherwise, the 845 * ssi->i2s_net will lose the settings for regular use cases. 846 */ 847 u8 i2s_net = ssi->i2s_net; 848 849 /* Normal + Network mode to send 16-bit data in 32-bit frames */ 850 if (fsl_ssi_is_i2s_bc_fp(ssi) && sample_size == 16) 851 i2s_net = SSI_SCR_I2S_MODE_NORMAL | SSI_SCR_NET; 852 853 /* Use Normal mode to send mono data at 1st slot of 2 slots */ 854 if (channels == 1) 855 i2s_net = SSI_SCR_I2S_MODE_NORMAL; 856 857 regmap_update_bits(regs, REG_SSI_SCR, 858 SSI_SCR_I2S_NET_MASK, i2s_net); 859 } 860 861 /* In synchronous mode, the SSI uses STCCR for capture */ 862 tx2 = tx || ssi->synchronous; 863 regmap_update_bits(regs, REG_SSI_SxCCR(tx2), SSI_SxCCR_WL_MASK, wl); 864 865 if (ssi->use_dyna_fifo) { 866 if (channels == 1) { 867 ssi->audio_config[0].n_fifos_dst = 1; 868 ssi->audio_config[1].n_fifos_src = 1; 869 vals[RX].srcr &= ~SSI_SRCR_RFEN1; 870 vals[TX].stcr &= ~SSI_STCR_TFEN1; 871 vals[RX].scr &= ~SSI_SCR_TCH_EN; 872 vals[TX].scr &= ~SSI_SCR_TCH_EN; 873 } else { 874 ssi->audio_config[0].n_fifos_dst = 2; 875 ssi->audio_config[1].n_fifos_src = 2; 876 vals[RX].srcr |= SSI_SRCR_RFEN1; 877 vals[TX].stcr |= SSI_STCR_TFEN1; 878 vals[RX].scr |= SSI_SCR_TCH_EN; 879 vals[TX].scr |= SSI_SCR_TCH_EN; 880 } 881 ssi->dma_params_tx.peripheral_config = &ssi->audio_config[0]; 882 ssi->dma_params_tx.peripheral_size = sizeof(ssi->audio_config[0]); 883 ssi->dma_params_rx.peripheral_config = &ssi->audio_config[1]; 884 ssi->dma_params_rx.peripheral_size = sizeof(ssi->audio_config[1]); 885 } 886 887 return 0; 888 } 889 890 static int fsl_ssi_hw_free(struct snd_pcm_substream *substream, 891 struct snd_soc_dai *dai) 892 { 893 struct snd_soc_pcm_runtime *rtd = snd_soc_substream_to_rtd(substream); 894 struct fsl_ssi *ssi = snd_soc_dai_get_drvdata(snd_soc_rtd_to_cpu(rtd, 0)); 895 896 if (fsl_ssi_is_i2s_clock_provider(ssi) && 897 ssi->baudclk_streams & BIT(substream->stream)) { 898 clk_disable_unprepare(ssi->baudclk); 899 ssi->baudclk_streams &= ~BIT(substream->stream); 900 } 901 902 return 0; 903 } 904 905 static int _fsl_ssi_set_dai_fmt(struct fsl_ssi *ssi, unsigned int fmt) 906 { 907 u32 strcr = 0, scr = 0, stcr, srcr, mask; 908 unsigned int slots; 909 910 ssi->dai_fmt = fmt; 911 912 /* Synchronize frame sync clock for TE to avoid data slipping */ 913 scr |= SSI_SCR_SYNC_TX_FS; 914 915 /* Set to default shifting settings: LSB_ALIGNED */ 916 strcr |= SSI_STCR_TXBIT0; 917 918 /* Use Network mode as default */ 919 ssi->i2s_net = SSI_SCR_NET; 920 switch (fmt & SND_SOC_DAIFMT_FORMAT_MASK) { 921 case SND_SOC_DAIFMT_I2S: 922 switch (fmt & SND_SOC_DAIFMT_CLOCK_PROVIDER_MASK) { 923 case SND_SOC_DAIFMT_BP_FP: 924 if (IS_ERR(ssi->baudclk)) { 925 dev_err(ssi->dev, 926 "missing baudclk for master mode\n"); 927 return -EINVAL; 928 } 929 fallthrough; 930 case SND_SOC_DAIFMT_BC_FP: 931 ssi->i2s_net |= SSI_SCR_I2S_MODE_MASTER; 932 break; 933 case SND_SOC_DAIFMT_BC_FC: 934 ssi->i2s_net |= SSI_SCR_I2S_MODE_SLAVE; 935 break; 936 default: 937 return -EINVAL; 938 } 939 940 slots = ssi->slots ? : 2; 941 regmap_update_bits(ssi->regs, REG_SSI_STCCR, 942 SSI_SxCCR_DC_MASK, SSI_SxCCR_DC(slots)); 943 regmap_update_bits(ssi->regs, REG_SSI_SRCCR, 944 SSI_SxCCR_DC_MASK, SSI_SxCCR_DC(slots)); 945 946 /* Data on rising edge of bclk, frame low, 1clk before data */ 947 strcr |= SSI_STCR_TFSI | SSI_STCR_TSCKP | SSI_STCR_TEFS; 948 break; 949 case SND_SOC_DAIFMT_LEFT_J: 950 /* Data on rising edge of bclk, frame high */ 951 strcr |= SSI_STCR_TSCKP; 952 break; 953 case SND_SOC_DAIFMT_DSP_A: 954 /* Data on rising edge of bclk, frame high, 1clk before data */ 955 strcr |= SSI_STCR_TFSL | SSI_STCR_TSCKP | SSI_STCR_TEFS; 956 break; 957 case SND_SOC_DAIFMT_DSP_B: 958 /* Data on rising edge of bclk, frame high */ 959 strcr |= SSI_STCR_TFSL | SSI_STCR_TSCKP; 960 break; 961 case SND_SOC_DAIFMT_AC97: 962 /* Data on falling edge of bclk, frame high, 1clk before data */ 963 strcr |= SSI_STCR_TEFS; 964 break; 965 default: 966 return -EINVAL; 967 } 968 969 scr |= ssi->i2s_net; 970 971 /* DAI clock inversion */ 972 switch (fmt & SND_SOC_DAIFMT_INV_MASK) { 973 case SND_SOC_DAIFMT_NB_NF: 974 /* Nothing to do for both normal cases */ 975 break; 976 case SND_SOC_DAIFMT_IB_NF: 977 /* Invert bit clock */ 978 strcr ^= SSI_STCR_TSCKP; 979 break; 980 case SND_SOC_DAIFMT_NB_IF: 981 /* Invert frame clock */ 982 strcr ^= SSI_STCR_TFSI; 983 break; 984 case SND_SOC_DAIFMT_IB_IF: 985 /* Invert both clocks */ 986 strcr ^= SSI_STCR_TSCKP; 987 strcr ^= SSI_STCR_TFSI; 988 break; 989 default: 990 return -EINVAL; 991 } 992 993 /* DAI clock provider masks */ 994 switch (fmt & SND_SOC_DAIFMT_CLOCK_PROVIDER_MASK) { 995 case SND_SOC_DAIFMT_BP_FP: 996 /* Output bit and frame sync clocks */ 997 strcr |= SSI_STCR_TFDIR | SSI_STCR_TXDIR; 998 scr |= SSI_SCR_SYS_CLK_EN; 999 break; 1000 case SND_SOC_DAIFMT_BC_FC: 1001 /* Input bit or frame sync clocks */ 1002 break; 1003 case SND_SOC_DAIFMT_BC_FP: 1004 /* Input bit clock but output frame sync clock */ 1005 strcr |= SSI_STCR_TFDIR; 1006 break; 1007 default: 1008 return -EINVAL; 1009 } 1010 1011 stcr = strcr; 1012 srcr = strcr; 1013 1014 /* Set SYN mode and clear RXDIR bit when using SYN or AC97 mode */ 1015 if (ssi->synchronous || fsl_ssi_is_ac97(ssi)) { 1016 srcr &= ~SSI_SRCR_RXDIR; 1017 scr |= SSI_SCR_SYN; 1018 } 1019 1020 mask = SSI_STCR_TFDIR | SSI_STCR_TXDIR | SSI_STCR_TSCKP | 1021 SSI_STCR_TFSL | SSI_STCR_TFSI | SSI_STCR_TEFS | SSI_STCR_TXBIT0; 1022 1023 regmap_update_bits(ssi->regs, REG_SSI_STCR, mask, stcr); 1024 regmap_update_bits(ssi->regs, REG_SSI_SRCR, mask, srcr); 1025 1026 mask = SSI_SCR_SYNC_TX_FS | SSI_SCR_I2S_MODE_MASK | 1027 SSI_SCR_SYS_CLK_EN | SSI_SCR_SYN; 1028 regmap_update_bits(ssi->regs, REG_SSI_SCR, mask, scr); 1029 1030 return 0; 1031 } 1032 1033 /** 1034 * fsl_ssi_set_dai_fmt - Configure Digital Audio Interface (DAI) Format 1035 * @dai: pointer to DAI 1036 * @fmt: format mask 1037 */ 1038 static int fsl_ssi_set_dai_fmt(struct snd_soc_dai *dai, unsigned int fmt) 1039 { 1040 struct fsl_ssi *ssi = snd_soc_dai_get_drvdata(dai); 1041 1042 /* AC97 configured DAIFMT earlier in the probe() */ 1043 if (fsl_ssi_is_ac97(ssi)) 1044 return 0; 1045 1046 return _fsl_ssi_set_dai_fmt(ssi, fmt); 1047 } 1048 1049 /** 1050 * fsl_ssi_set_dai_tdm_slot - Set TDM slot number and slot width 1051 * @dai: pointer to DAI 1052 * @tx_mask: mask for TX 1053 * @rx_mask: mask for RX 1054 * @slots: number of slots 1055 * @slot_width: number of bits per slot 1056 */ 1057 static int fsl_ssi_set_dai_tdm_slot(struct snd_soc_dai *dai, u32 tx_mask, 1058 u32 rx_mask, int slots, int slot_width) 1059 { 1060 struct fsl_ssi *ssi = snd_soc_dai_get_drvdata(dai); 1061 struct regmap *regs = ssi->regs; 1062 u32 val; 1063 1064 /* The word length should be 8, 10, 12, 16, 18, 20, 22 or 24 */ 1065 if (slot_width & 1 || slot_width < 8 || slot_width > 24) { 1066 dev_err(dai->dev, "invalid slot width: %d\n", slot_width); 1067 return -EINVAL; 1068 } 1069 1070 /* The slot number should be >= 2 if using Network mode or I2S mode */ 1071 if (ssi->i2s_net && slots < 2) { 1072 dev_err(dai->dev, "slot number should be >= 2 in I2S or NET\n"); 1073 return -EINVAL; 1074 } 1075 1076 regmap_update_bits(regs, REG_SSI_STCCR, 1077 SSI_SxCCR_DC_MASK, SSI_SxCCR_DC(slots)); 1078 regmap_update_bits(regs, REG_SSI_SRCCR, 1079 SSI_SxCCR_DC_MASK, SSI_SxCCR_DC(slots)); 1080 1081 /* Save the SCR register value */ 1082 regmap_read(regs, REG_SSI_SCR, &val); 1083 /* Temporarily enable SSI to allow SxMSKs to be configurable */ 1084 regmap_update_bits(regs, REG_SSI_SCR, SSI_SCR_SSIEN, SSI_SCR_SSIEN); 1085 1086 regmap_write(regs, REG_SSI_STMSK, ~tx_mask); 1087 regmap_write(regs, REG_SSI_SRMSK, ~rx_mask); 1088 1089 /* Restore the value of SSIEN bit */ 1090 regmap_update_bits(regs, REG_SSI_SCR, SSI_SCR_SSIEN, val); 1091 1092 ssi->slot_width = slot_width; 1093 ssi->slots = slots; 1094 1095 return 0; 1096 } 1097 1098 /** 1099 * fsl_ssi_trigger - Start or stop SSI and corresponding DMA transaction. 1100 * @substream: ASoC substream 1101 * @cmd: trigger command 1102 * @dai: pointer to DAI 1103 * 1104 * The DMA channel is in external master start and pause mode, which 1105 * means the SSI completely controls the flow of data. 1106 */ 1107 static int fsl_ssi_trigger(struct snd_pcm_substream *substream, int cmd, 1108 struct snd_soc_dai *dai) 1109 { 1110 struct snd_soc_pcm_runtime *rtd = snd_soc_substream_to_rtd(substream); 1111 struct fsl_ssi *ssi = snd_soc_dai_get_drvdata(snd_soc_rtd_to_cpu(rtd, 0)); 1112 bool tx = substream->stream == SNDRV_PCM_STREAM_PLAYBACK; 1113 1114 switch (cmd) { 1115 case SNDRV_PCM_TRIGGER_START: 1116 case SNDRV_PCM_TRIGGER_RESUME: 1117 case SNDRV_PCM_TRIGGER_PAUSE_RELEASE: 1118 /* 1119 * SACCST might be modified via AC Link by a CODEC if it sends 1120 * extra bits in their SLOTREQ requests, which'll accidentally 1121 * send valid data to slots other than normal playback slots. 1122 * 1123 * To be safe, configure SACCST right before TX starts. 1124 */ 1125 if (tx && fsl_ssi_is_ac97(ssi)) 1126 fsl_ssi_tx_ac97_saccst_setup(ssi); 1127 fsl_ssi_config_enable(ssi, tx); 1128 break; 1129 1130 case SNDRV_PCM_TRIGGER_STOP: 1131 case SNDRV_PCM_TRIGGER_SUSPEND: 1132 case SNDRV_PCM_TRIGGER_PAUSE_PUSH: 1133 fsl_ssi_config_disable(ssi, tx); 1134 break; 1135 1136 default: 1137 return -EINVAL; 1138 } 1139 1140 return 0; 1141 } 1142 1143 static int fsl_ssi_dai_probe(struct snd_soc_dai *dai) 1144 { 1145 struct fsl_ssi *ssi = snd_soc_dai_get_drvdata(dai); 1146 1147 if (ssi->soc->imx && ssi->use_dma) 1148 snd_soc_dai_init_dma_data(dai, &ssi->dma_params_tx, 1149 &ssi->dma_params_rx); 1150 1151 return 0; 1152 } 1153 1154 static const struct snd_soc_dai_ops fsl_ssi_dai_ops = { 1155 .probe = fsl_ssi_dai_probe, 1156 .startup = fsl_ssi_startup, 1157 .shutdown = fsl_ssi_shutdown, 1158 .hw_params = fsl_ssi_hw_params, 1159 .hw_free = fsl_ssi_hw_free, 1160 .set_fmt = fsl_ssi_set_dai_fmt, 1161 .set_tdm_slot = fsl_ssi_set_dai_tdm_slot, 1162 .trigger = fsl_ssi_trigger, 1163 }; 1164 1165 static struct snd_soc_dai_driver fsl_ssi_dai_template = { 1166 .playback = { 1167 .stream_name = "CPU-Playback", 1168 .channels_min = 1, 1169 .channels_max = 32, 1170 .rates = SNDRV_PCM_RATE_CONTINUOUS, 1171 .formats = FSLSSI_I2S_FORMATS, 1172 }, 1173 .capture = { 1174 .stream_name = "CPU-Capture", 1175 .channels_min = 1, 1176 .channels_max = 32, 1177 .rates = SNDRV_PCM_RATE_CONTINUOUS, 1178 .formats = FSLSSI_I2S_FORMATS, 1179 }, 1180 .ops = &fsl_ssi_dai_ops, 1181 }; 1182 1183 static const struct snd_soc_component_driver fsl_ssi_component = { 1184 .name = "fsl-ssi", 1185 .legacy_dai_naming = 1, 1186 }; 1187 1188 static struct snd_soc_dai_driver fsl_ssi_ac97_dai = { 1189 .symmetric_channels = 1, 1190 .playback = { 1191 .stream_name = "CPU AC97 Playback", 1192 .channels_min = 2, 1193 .channels_max = 2, 1194 .rates = SNDRV_PCM_RATE_8000_48000, 1195 .formats = SNDRV_PCM_FMTBIT_S16 | SNDRV_PCM_FMTBIT_S20, 1196 }, 1197 .capture = { 1198 .stream_name = "CPU AC97 Capture", 1199 .channels_min = 2, 1200 .channels_max = 2, 1201 .rates = SNDRV_PCM_RATE_48000, 1202 /* 16-bit capture is broken (errata ERR003778) */ 1203 .formats = SNDRV_PCM_FMTBIT_S20, 1204 }, 1205 .ops = &fsl_ssi_dai_ops, 1206 }; 1207 1208 static struct fsl_ssi *fsl_ac97_data; 1209 1210 static void fsl_ssi_ac97_write(struct snd_ac97 *ac97, unsigned short reg, 1211 unsigned short val) 1212 { 1213 struct regmap *regs = fsl_ac97_data->regs; 1214 unsigned int lreg; 1215 unsigned int lval; 1216 int ret; 1217 1218 if (reg > 0x7f) 1219 return; 1220 1221 mutex_lock(&fsl_ac97_data->ac97_reg_lock); 1222 1223 ret = clk_prepare_enable(fsl_ac97_data->clk); 1224 if (ret) { 1225 pr_err("ac97 write clk_prepare_enable failed: %d\n", 1226 ret); 1227 goto ret_unlock; 1228 } 1229 1230 lreg = reg << 12; 1231 regmap_write(regs, REG_SSI_SACADD, lreg); 1232 1233 lval = val << 4; 1234 regmap_write(regs, REG_SSI_SACDAT, lval); 1235 1236 regmap_update_bits(regs, REG_SSI_SACNT, 1237 SSI_SACNT_RDWR_MASK, SSI_SACNT_WR); 1238 udelay(100); 1239 1240 clk_disable_unprepare(fsl_ac97_data->clk); 1241 1242 ret_unlock: 1243 mutex_unlock(&fsl_ac97_data->ac97_reg_lock); 1244 } 1245 1246 static unsigned short fsl_ssi_ac97_read(struct snd_ac97 *ac97, 1247 unsigned short reg) 1248 { 1249 struct regmap *regs = fsl_ac97_data->regs; 1250 unsigned short val = 0; 1251 u32 reg_val; 1252 unsigned int lreg; 1253 int ret; 1254 1255 mutex_lock(&fsl_ac97_data->ac97_reg_lock); 1256 1257 ret = clk_prepare_enable(fsl_ac97_data->clk); 1258 if (ret) { 1259 pr_err("ac97 read clk_prepare_enable failed: %d\n", ret); 1260 goto ret_unlock; 1261 } 1262 1263 lreg = (reg & 0x7f) << 12; 1264 regmap_write(regs, REG_SSI_SACADD, lreg); 1265 regmap_update_bits(regs, REG_SSI_SACNT, 1266 SSI_SACNT_RDWR_MASK, SSI_SACNT_RD); 1267 1268 udelay(100); 1269 1270 regmap_read(regs, REG_SSI_SACDAT, ®_val); 1271 val = (reg_val >> 4) & 0xffff; 1272 1273 clk_disable_unprepare(fsl_ac97_data->clk); 1274 1275 ret_unlock: 1276 mutex_unlock(&fsl_ac97_data->ac97_reg_lock); 1277 return val; 1278 } 1279 1280 static struct snd_ac97_bus_ops fsl_ssi_ac97_ops = { 1281 .read = fsl_ssi_ac97_read, 1282 .write = fsl_ssi_ac97_write, 1283 }; 1284 1285 /** 1286 * fsl_ssi_hw_init - Initialize SSI registers 1287 * @ssi: SSI context 1288 */ 1289 static int fsl_ssi_hw_init(struct fsl_ssi *ssi) 1290 { 1291 u32 wm = ssi->fifo_watermark; 1292 1293 /* Initialize regvals */ 1294 fsl_ssi_setup_regvals(ssi); 1295 1296 /* Set watermarks */ 1297 regmap_write(ssi->regs, REG_SSI_SFCSR, 1298 SSI_SFCSR_TFWM0(wm) | SSI_SFCSR_RFWM0(wm) | 1299 SSI_SFCSR_TFWM1(wm) | SSI_SFCSR_RFWM1(wm)); 1300 1301 /* Enable Dual FIFO mode */ 1302 if (ssi->use_dual_fifo) 1303 regmap_update_bits(ssi->regs, REG_SSI_SCR, 1304 SSI_SCR_TCH_EN, SSI_SCR_TCH_EN); 1305 1306 /* AC97 should start earlier to communicate with CODECs */ 1307 if (fsl_ssi_is_ac97(ssi)) { 1308 _fsl_ssi_set_dai_fmt(ssi, ssi->dai_fmt); 1309 fsl_ssi_setup_ac97(ssi); 1310 } 1311 1312 return 0; 1313 } 1314 1315 /** 1316 * fsl_ssi_hw_clean - Clear SSI registers 1317 * @ssi: SSI context 1318 */ 1319 static void fsl_ssi_hw_clean(struct fsl_ssi *ssi) 1320 { 1321 /* Disable registers for AC97 */ 1322 if (fsl_ssi_is_ac97(ssi)) { 1323 /* Disable TE and RE bits first */ 1324 regmap_update_bits(ssi->regs, REG_SSI_SCR, 1325 SSI_SCR_TE | SSI_SCR_RE, 0); 1326 /* Disable AC97 mode */ 1327 regmap_write(ssi->regs, REG_SSI_SACNT, 0); 1328 /* Unset WAIT bits */ 1329 regmap_write(ssi->regs, REG_SSI_SOR, 0); 1330 /* Disable SSI -- software reset */ 1331 regmap_update_bits(ssi->regs, REG_SSI_SCR, SSI_SCR_SSIEN, 0); 1332 } 1333 } 1334 1335 /* 1336 * Make every character in a string lower-case 1337 */ 1338 static void make_lowercase(char *s) 1339 { 1340 if (!s) 1341 return; 1342 for (; *s; s++) 1343 *s = tolower(*s); 1344 } 1345 1346 static int fsl_ssi_imx_probe(struct platform_device *pdev, 1347 struct fsl_ssi *ssi, void __iomem *iomem) 1348 { 1349 struct device *dev = &pdev->dev; 1350 int ret; 1351 1352 /* Backward compatible for a DT without ipg clock name assigned */ 1353 if (ssi->has_ipg_clk_name) 1354 ssi->clk = devm_clk_get(dev, "ipg"); 1355 else 1356 ssi->clk = devm_clk_get(dev, NULL); 1357 if (IS_ERR(ssi->clk)) { 1358 ret = PTR_ERR(ssi->clk); 1359 dev_err(dev, "failed to get clock: %d\n", ret); 1360 return ret; 1361 } 1362 1363 /* Enable the clock since regmap will not handle it in this case */ 1364 if (!ssi->has_ipg_clk_name) { 1365 ret = clk_prepare_enable(ssi->clk); 1366 if (ret) { 1367 dev_err(dev, "clk_prepare_enable failed: %d\n", ret); 1368 return ret; 1369 } 1370 } 1371 1372 /* Do not error out for consumer cases that live without a baud clock */ 1373 ssi->baudclk = devm_clk_get(dev, "baud"); 1374 if (IS_ERR(ssi->baudclk)) 1375 dev_dbg(dev, "failed to get baud clock: %ld\n", 1376 PTR_ERR(ssi->baudclk)); 1377 1378 ssi->dma_params_tx.maxburst = ssi->dma_maxburst; 1379 ssi->dma_params_rx.maxburst = ssi->dma_maxburst; 1380 ssi->dma_params_tx.addr = ssi->ssi_phys + REG_SSI_STX0; 1381 ssi->dma_params_rx.addr = ssi->ssi_phys + REG_SSI_SRX0; 1382 1383 /* Use even numbers to avoid channel swap due to SDMA script design */ 1384 if (ssi->use_dual_fifo || ssi->use_dyna_fifo) { 1385 ssi->dma_params_tx.maxburst &= ~0x1; 1386 ssi->dma_params_rx.maxburst &= ~0x1; 1387 } 1388 1389 if (!ssi->use_dma) { 1390 /* 1391 * Some boards use an incompatible codec. Use imx-fiq-pcm-audio 1392 * to get it working, as DMA is not possible in this situation. 1393 */ 1394 ssi->fiq_params.irq = ssi->irq; 1395 ssi->fiq_params.base = iomem; 1396 ssi->fiq_params.dma_params_rx = &ssi->dma_params_rx; 1397 ssi->fiq_params.dma_params_tx = &ssi->dma_params_tx; 1398 1399 ret = imx_pcm_fiq_init(pdev, &ssi->fiq_params); 1400 if (ret) 1401 goto error_pcm; 1402 } else { 1403 ret = imx_pcm_dma_init(pdev); 1404 if (ret) { 1405 dev_err_probe(dev, ret, "Failed to init PCM DMA\n"); 1406 goto error_pcm; 1407 } 1408 } 1409 1410 return 0; 1411 1412 error_pcm: 1413 if (!ssi->has_ipg_clk_name) 1414 clk_disable_unprepare(ssi->clk); 1415 1416 return ret; 1417 } 1418 1419 static void fsl_ssi_imx_clean(struct platform_device *pdev, struct fsl_ssi *ssi) 1420 { 1421 if (!ssi->use_dma) 1422 imx_pcm_fiq_exit(pdev); 1423 if (!ssi->has_ipg_clk_name) 1424 clk_disable_unprepare(ssi->clk); 1425 } 1426 1427 static int fsl_ssi_probe_from_dt(struct fsl_ssi *ssi) 1428 { 1429 struct device *dev = ssi->dev; 1430 struct device_node *np = dev->of_node; 1431 const char *p, *sprop; 1432 const __be32 *iprop; 1433 u32 dmas[4]; 1434 int ret; 1435 1436 ret = of_property_match_string(np, "clock-names", "ipg"); 1437 /* Get error code if not found */ 1438 ssi->has_ipg_clk_name = ret >= 0; 1439 1440 /* Check if being used in AC97 mode */ 1441 sprop = of_get_property(np, "fsl,mode", NULL); 1442 if (sprop && !strcmp(sprop, "ac97-slave")) { 1443 ssi->dai_fmt = FSLSSI_AC97_DAIFMT; 1444 1445 ret = of_property_read_u32(np, "cell-index", &ssi->card_idx); 1446 if (ret) { 1447 dev_err(dev, "failed to get SSI index property\n"); 1448 return -EINVAL; 1449 } 1450 strcpy(ssi->card_name, "ac97-codec"); 1451 } else if (!of_property_read_bool(np, "fsl,ssi-asynchronous")) { 1452 /* 1453 * In synchronous mode, STCK and STFS ports are used by RX 1454 * as well. So the software should limit the sample rates, 1455 * sample bits and channels to be symmetric. 1456 * 1457 * This is exclusive with FSLSSI_AC97_FORMATS as AC97 runs 1458 * in the SSI synchronous mode however it does not have to 1459 * limit symmetric sample rates and sample bits. 1460 */ 1461 ssi->synchronous = true; 1462 } 1463 1464 /* Select DMA or FIQ */ 1465 ssi->use_dma = !of_property_read_bool(np, "fsl,fiq-stream-filter"); 1466 1467 /* Fetch FIFO depth; Set to 8 for older DT without this property */ 1468 iprop = of_get_property(np, "fsl,fifo-depth", NULL); 1469 if (iprop) 1470 ssi->fifo_depth = be32_to_cpup(iprop); 1471 else 1472 ssi->fifo_depth = 8; 1473 1474 /* Use dual FIFO mode depending on the support from SDMA script */ 1475 ret = of_property_read_u32_array(np, "dmas", dmas, 4); 1476 if (ssi->use_dma && !ret && dmas[2] == IMX_DMATYPE_SSI_DUAL) 1477 ssi->use_dual_fifo = true; 1478 1479 if (ssi->use_dma && !ret && dmas[2] == IMX_DMATYPE_MULTI_SAI) 1480 ssi->use_dyna_fifo = true; 1481 /* 1482 * Backward compatible for older bindings by manually triggering the 1483 * machine driver's probe(). Use /compatible property, including the 1484 * address of CPU DAI driver structure, as the name of machine driver 1485 * 1486 * If card_name is set by AC97 earlier, bypass here since it uses a 1487 * different name to register the device. 1488 */ 1489 if (!ssi->card_name[0] && of_get_property(np, "codec-handle", NULL)) { 1490 struct device_node *root = of_find_node_by_path("/"); 1491 1492 sprop = of_get_property(root, "compatible", NULL); 1493 of_node_put(root); 1494 /* Strip "fsl," in the compatible name if applicable */ 1495 p = strrchr(sprop, ','); 1496 if (p) 1497 sprop = p + 1; 1498 snprintf(ssi->card_name, sizeof(ssi->card_name), 1499 "snd-soc-%s", sprop); 1500 make_lowercase(ssi->card_name); 1501 ssi->card_idx = 0; 1502 } 1503 1504 return 0; 1505 } 1506 1507 static int fsl_ssi_probe(struct platform_device *pdev) 1508 { 1509 struct regmap_config regconfig = fsl_ssi_regconfig; 1510 struct device *dev = &pdev->dev; 1511 struct fsl_ssi *ssi; 1512 struct resource *res; 1513 void __iomem *iomem; 1514 int ret = 0; 1515 1516 ssi = devm_kzalloc(dev, sizeof(*ssi), GFP_KERNEL); 1517 if (!ssi) 1518 return -ENOMEM; 1519 1520 ssi->dev = dev; 1521 ssi->soc = of_device_get_match_data(&pdev->dev); 1522 1523 /* Probe from DT */ 1524 ret = fsl_ssi_probe_from_dt(ssi); 1525 if (ret) 1526 return ret; 1527 1528 if (fsl_ssi_is_ac97(ssi)) { 1529 memcpy(&ssi->cpu_dai_drv, &fsl_ssi_ac97_dai, 1530 sizeof(fsl_ssi_ac97_dai)); 1531 fsl_ac97_data = ssi; 1532 } else { 1533 memcpy(&ssi->cpu_dai_drv, &fsl_ssi_dai_template, 1534 sizeof(fsl_ssi_dai_template)); 1535 } 1536 ssi->cpu_dai_drv.name = dev_name(dev); 1537 1538 iomem = devm_platform_get_and_ioremap_resource(pdev, 0, &res); 1539 if (IS_ERR(iomem)) 1540 return PTR_ERR(iomem); 1541 ssi->ssi_phys = res->start; 1542 1543 if (ssi->soc->imx21regs) { 1544 /* No SACC{ST,EN,DIS} regs in imx21-class SSI */ 1545 regconfig.max_register = REG_SSI_SRMSK; 1546 regconfig.num_reg_defaults_raw = 1547 REG_SSI_SRMSK / sizeof(uint32_t) + 1; 1548 } 1549 1550 if (ssi->has_ipg_clk_name) 1551 ssi->regs = devm_regmap_init_mmio_clk(dev, "ipg", iomem, 1552 ®config); 1553 else 1554 ssi->regs = devm_regmap_init_mmio(dev, iomem, ®config); 1555 if (IS_ERR(ssi->regs)) { 1556 dev_err(dev, "failed to init register map\n"); 1557 return PTR_ERR(ssi->regs); 1558 } 1559 1560 ssi->irq = platform_get_irq(pdev, 0); 1561 if (ssi->irq < 0) 1562 return ssi->irq; 1563 1564 /* Set software limitations for synchronous mode except AC97 */ 1565 if (ssi->synchronous && !fsl_ssi_is_ac97(ssi)) { 1566 ssi->cpu_dai_drv.symmetric_rate = 1; 1567 ssi->cpu_dai_drv.symmetric_channels = 1; 1568 ssi->cpu_dai_drv.symmetric_sample_bits = 1; 1569 } 1570 1571 /* 1572 * Configure TX and RX DMA watermarks -- when to send a DMA request 1573 * 1574 * Values should be tested to avoid FIFO under/over run. Set maxburst 1575 * to fifo_watermark to maxiumize DMA transaction to reduce overhead. 1576 */ 1577 switch (ssi->fifo_depth) { 1578 case 15: 1579 /* 1580 * Set to 8 as a balanced configuration -- When TX FIFO has 8 1581 * empty slots, send a DMA request to fill these 8 slots. The 1582 * remaining 7 slots should be able to allow DMA to finish the 1583 * transaction before TX FIFO underruns; Same applies to RX. 1584 * 1585 * Tested with cases running at 48kHz @ 16 bits x 16 channels 1586 */ 1587 ssi->fifo_watermark = 8; 1588 ssi->dma_maxburst = 8; 1589 break; 1590 case 8: 1591 default: 1592 /* Safely use old watermark configurations for older chips */ 1593 ssi->fifo_watermark = ssi->fifo_depth - 2; 1594 ssi->dma_maxburst = ssi->fifo_depth - 2; 1595 break; 1596 } 1597 1598 dev_set_drvdata(dev, ssi); 1599 1600 if (ssi->soc->imx) { 1601 ret = fsl_ssi_imx_probe(pdev, ssi, iomem); 1602 if (ret) 1603 return ret; 1604 } 1605 1606 if (fsl_ssi_is_ac97(ssi)) { 1607 mutex_init(&ssi->ac97_reg_lock); 1608 ret = snd_soc_set_ac97_ops_of_reset(&fsl_ssi_ac97_ops, pdev); 1609 if (ret) { 1610 dev_err(dev, "failed to set AC'97 ops\n"); 1611 goto error_ac97_ops; 1612 } 1613 } 1614 1615 ret = devm_snd_soc_register_component(dev, &fsl_ssi_component, 1616 &ssi->cpu_dai_drv, 1); 1617 if (ret) { 1618 dev_err(dev, "failed to register DAI: %d\n", ret); 1619 goto error_asoc_register; 1620 } 1621 1622 if (ssi->use_dma) { 1623 ret = devm_request_irq(dev, ssi->irq, fsl_ssi_isr, 0, 1624 dev_name(dev), ssi); 1625 if (ret < 0) { 1626 dev_err(dev, "failed to claim irq %u\n", ssi->irq); 1627 goto error_asoc_register; 1628 } 1629 } 1630 1631 fsl_ssi_debugfs_create(&ssi->dbg_stats, dev); 1632 1633 /* Initially configures SSI registers */ 1634 fsl_ssi_hw_init(ssi); 1635 1636 /* Register a platform device for older bindings or AC97 */ 1637 if (ssi->card_name[0]) { 1638 struct device *parent = dev; 1639 /* 1640 * Do not set SSI dev as the parent of AC97 CODEC device since 1641 * it does not have a DT node. Otherwise ASoC core will assume 1642 * CODEC has the same DT node as the SSI, so it may bypass the 1643 * dai_probe() of SSI and then cause NULL DMA data pointers. 1644 */ 1645 if (fsl_ssi_is_ac97(ssi)) 1646 parent = NULL; 1647 1648 ssi->card_pdev = platform_device_register_data(parent, 1649 ssi->card_name, ssi->card_idx, NULL, 0); 1650 if (IS_ERR(ssi->card_pdev)) { 1651 ret = PTR_ERR(ssi->card_pdev); 1652 dev_err(dev, "failed to register %s: %d\n", 1653 ssi->card_name, ret); 1654 goto error_sound_card; 1655 } 1656 } 1657 1658 return 0; 1659 1660 error_sound_card: 1661 fsl_ssi_debugfs_remove(&ssi->dbg_stats); 1662 error_asoc_register: 1663 if (fsl_ssi_is_ac97(ssi)) 1664 snd_soc_set_ac97_ops(NULL); 1665 error_ac97_ops: 1666 if (fsl_ssi_is_ac97(ssi)) 1667 mutex_destroy(&ssi->ac97_reg_lock); 1668 1669 if (ssi->soc->imx) 1670 fsl_ssi_imx_clean(pdev, ssi); 1671 1672 return ret; 1673 } 1674 1675 static void fsl_ssi_remove(struct platform_device *pdev) 1676 { 1677 struct fsl_ssi *ssi = dev_get_drvdata(&pdev->dev); 1678 1679 fsl_ssi_debugfs_remove(&ssi->dbg_stats); 1680 1681 if (ssi->card_pdev) 1682 platform_device_unregister(ssi->card_pdev); 1683 1684 /* Clean up SSI registers */ 1685 fsl_ssi_hw_clean(ssi); 1686 1687 if (ssi->soc->imx) 1688 fsl_ssi_imx_clean(pdev, ssi); 1689 1690 if (fsl_ssi_is_ac97(ssi)) { 1691 snd_soc_set_ac97_ops(NULL); 1692 mutex_destroy(&ssi->ac97_reg_lock); 1693 } 1694 } 1695 1696 static int fsl_ssi_suspend(struct device *dev) 1697 { 1698 struct fsl_ssi *ssi = dev_get_drvdata(dev); 1699 struct regmap *regs = ssi->regs; 1700 1701 regmap_read(regs, REG_SSI_SFCSR, &ssi->regcache_sfcsr); 1702 regmap_read(regs, REG_SSI_SACNT, &ssi->regcache_sacnt); 1703 1704 regcache_cache_only(regs, true); 1705 regcache_mark_dirty(regs); 1706 1707 return 0; 1708 } 1709 1710 static int fsl_ssi_resume(struct device *dev) 1711 { 1712 struct fsl_ssi *ssi = dev_get_drvdata(dev); 1713 struct regmap *regs = ssi->regs; 1714 1715 regcache_cache_only(regs, false); 1716 1717 regmap_update_bits(regs, REG_SSI_SFCSR, 1718 SSI_SFCSR_RFWM1_MASK | SSI_SFCSR_TFWM1_MASK | 1719 SSI_SFCSR_RFWM0_MASK | SSI_SFCSR_TFWM0_MASK, 1720 ssi->regcache_sfcsr); 1721 regmap_write(regs, REG_SSI_SACNT, ssi->regcache_sacnt); 1722 1723 return regcache_sync(regs); 1724 } 1725 1726 static const struct dev_pm_ops fsl_ssi_pm = { 1727 SYSTEM_SLEEP_PM_OPS(fsl_ssi_suspend, fsl_ssi_resume) 1728 }; 1729 1730 static struct platform_driver fsl_ssi_driver = { 1731 .driver = { 1732 .name = "fsl-ssi-dai", 1733 .of_match_table = fsl_ssi_ids, 1734 .pm = pm_sleep_ptr(&fsl_ssi_pm), 1735 }, 1736 .probe = fsl_ssi_probe, 1737 .remove = fsl_ssi_remove, 1738 }; 1739 1740 module_platform_driver(fsl_ssi_driver); 1741 1742 MODULE_ALIAS("platform:fsl-ssi-dai"); 1743 MODULE_AUTHOR("Timur Tabi <timur@freescale.com>"); 1744 MODULE_DESCRIPTION("Freescale Synchronous Serial Interface (SSI) ASoC Driver"); 1745 MODULE_LICENSE("GPL v2"); 1746