1 // SPDX-License-Identifier: GPL-2.0-only 2 /* 3 * wm8960.c -- WM8960 ALSA SoC Audio driver 4 * 5 * Copyright 2007-11 Wolfson Microelectronics, plc 6 * 7 * Author: Liam Girdwood 8 */ 9 10 #include <linux/module.h> 11 #include <linux/moduleparam.h> 12 #include <linux/init.h> 13 #include <linux/delay.h> 14 #include <linux/pm.h> 15 #include <linux/clk.h> 16 #include <linux/i2c.h> 17 #include <linux/slab.h> 18 #include <sound/core.h> 19 #include <sound/pcm.h> 20 #include <sound/pcm_params.h> 21 #include <sound/soc.h> 22 #include <sound/initval.h> 23 #include <sound/tlv.h> 24 #include <sound/wm8960.h> 25 26 #include "wm8960.h" 27 28 /* R25 - Power 1 */ 29 #define WM8960_VMID_MASK 0x180 30 #define WM8960_VREF 0x40 31 32 /* R26 - Power 2 */ 33 #define WM8960_PWR2_LOUT1 0x40 34 #define WM8960_PWR2_ROUT1 0x20 35 #define WM8960_PWR2_OUT3 0x02 36 37 /* R28 - Anti-pop 1 */ 38 #define WM8960_POBCTRL 0x80 39 #define WM8960_BUFDCOPEN 0x10 40 #define WM8960_BUFIOEN 0x08 41 #define WM8960_SOFT_ST 0x04 42 #define WM8960_HPSTBY 0x01 43 44 /* R29 - Anti-pop 2 */ 45 #define WM8960_DISOP 0x40 46 #define WM8960_DRES_MASK 0x30 47 48 static bool is_pll_freq_available(unsigned int source, unsigned int target); 49 static int wm8960_set_pll(struct snd_soc_component *component, 50 unsigned int freq_in, unsigned int freq_out); 51 /* 52 * wm8960 register cache 53 * We can't read the WM8960 register space when we are 54 * using 2 wire for device control, so we cache them instead. 55 */ 56 static const struct reg_default wm8960_reg_defaults[] = { 57 { 0x0, 0x00a7 }, 58 { 0x1, 0x00a7 }, 59 { 0x2, 0x0000 }, 60 { 0x3, 0x0000 }, 61 { 0x4, 0x0000 }, 62 { 0x5, 0x0008 }, 63 { 0x6, 0x0000 }, 64 { 0x7, 0x000a }, 65 { 0x8, 0x01c0 }, 66 { 0x9, 0x0000 }, 67 { 0xa, 0x00ff }, 68 { 0xb, 0x00ff }, 69 70 { 0x10, 0x0000 }, 71 { 0x11, 0x007b }, 72 { 0x12, 0x0100 }, 73 { 0x13, 0x0032 }, 74 { 0x14, 0x0000 }, 75 { 0x15, 0x00c3 }, 76 { 0x16, 0x00c3 }, 77 { 0x17, 0x01c0 }, 78 { 0x18, 0x0000 }, 79 { 0x19, 0x0000 }, 80 { 0x1a, 0x0000 }, 81 { 0x1b, 0x0000 }, 82 { 0x1c, 0x0000 }, 83 { 0x1d, 0x0000 }, 84 85 { 0x20, 0x0100 }, 86 { 0x21, 0x0100 }, 87 { 0x22, 0x0050 }, 88 89 { 0x25, 0x0050 }, 90 { 0x26, 0x0000 }, 91 { 0x27, 0x0000 }, 92 { 0x28, 0x0000 }, 93 { 0x29, 0x0000 }, 94 { 0x2a, 0x0040 }, 95 { 0x2b, 0x0000 }, 96 { 0x2c, 0x0000 }, 97 { 0x2d, 0x0050 }, 98 { 0x2e, 0x0050 }, 99 { 0x2f, 0x0000 }, 100 { 0x30, 0x0002 }, 101 { 0x31, 0x0037 }, 102 103 { 0x33, 0x0080 }, 104 { 0x34, 0x0008 }, 105 { 0x35, 0x0031 }, 106 { 0x36, 0x0026 }, 107 { 0x37, 0x00e9 }, 108 }; 109 110 static bool wm8960_volatile(struct device *dev, unsigned int reg) 111 { 112 switch (reg) { 113 case WM8960_RESET: 114 return true; 115 default: 116 return false; 117 } 118 } 119 120 struct wm8960_priv { 121 struct clk *mclk; 122 struct regmap *regmap; 123 int (*set_bias_level)(struct snd_soc_component *, 124 enum snd_soc_bias_level level); 125 struct snd_soc_dapm_widget *lout1; 126 struct snd_soc_dapm_widget *rout1; 127 struct snd_soc_dapm_widget *out3; 128 bool deemph; 129 int lrclk; 130 int bclk; 131 int sysclk; 132 int clk_id; 133 int freq_in; 134 bool is_stream_in_use[2]; 135 struct wm8960_data pdata; 136 }; 137 138 #define wm8960_reset(c) regmap_write(c, WM8960_RESET, 0) 139 140 /* enumerated controls */ 141 static const char *wm8960_polarity[] = {"No Inversion", "Left Inverted", 142 "Right Inverted", "Stereo Inversion"}; 143 static const char *wm8960_3d_upper_cutoff[] = {"High", "Low"}; 144 static const char *wm8960_3d_lower_cutoff[] = {"Low", "High"}; 145 static const char *wm8960_alcfunc[] = {"Off", "Right", "Left", "Stereo"}; 146 static const char *wm8960_alcmode[] = {"ALC", "Limiter"}; 147 static const char *wm8960_adc_data_output_sel[] = { 148 "Left Data = Left ADC; Right Data = Right ADC", 149 "Left Data = Left ADC; Right Data = Left ADC", 150 "Left Data = Right ADC; Right Data = Right ADC", 151 "Left Data = Right ADC; Right Data = Left ADC", 152 }; 153 static const char *wm8960_dmonomix[] = {"Stereo", "Mono"}; 154 155 static const struct soc_enum wm8960_enum[] = { 156 SOC_ENUM_SINGLE(WM8960_DACCTL1, 5, 4, wm8960_polarity), 157 SOC_ENUM_SINGLE(WM8960_DACCTL2, 5, 4, wm8960_polarity), 158 SOC_ENUM_SINGLE(WM8960_3D, 6, 2, wm8960_3d_upper_cutoff), 159 SOC_ENUM_SINGLE(WM8960_3D, 5, 2, wm8960_3d_lower_cutoff), 160 SOC_ENUM_SINGLE(WM8960_ALC1, 7, 4, wm8960_alcfunc), 161 SOC_ENUM_SINGLE(WM8960_ALC3, 8, 2, wm8960_alcmode), 162 SOC_ENUM_SINGLE(WM8960_ADDCTL1, 2, 4, wm8960_adc_data_output_sel), 163 SOC_ENUM_SINGLE(WM8960_ADDCTL1, 4, 2, wm8960_dmonomix), 164 }; 165 166 static const int deemph_settings[] = { 0, 32000, 44100, 48000 }; 167 168 static int wm8960_set_deemph(struct snd_soc_component *component) 169 { 170 struct wm8960_priv *wm8960 = snd_soc_component_get_drvdata(component); 171 int val, i, best; 172 173 /* If we're using deemphasis select the nearest available sample 174 * rate. 175 */ 176 if (wm8960->deemph) { 177 best = 1; 178 for (i = 2; i < ARRAY_SIZE(deemph_settings); i++) { 179 if (abs(deemph_settings[i] - wm8960->lrclk) < 180 abs(deemph_settings[best] - wm8960->lrclk)) 181 best = i; 182 } 183 184 val = best << 1; 185 } else { 186 val = 0; 187 } 188 189 dev_dbg(component->dev, "Set deemphasis %d\n", val); 190 191 return snd_soc_component_update_bits(component, WM8960_DACCTL1, 192 0x6, val); 193 } 194 195 static int wm8960_get_deemph(struct snd_kcontrol *kcontrol, 196 struct snd_ctl_elem_value *ucontrol) 197 { 198 struct snd_soc_component *component = snd_soc_kcontrol_component(kcontrol); 199 struct wm8960_priv *wm8960 = snd_soc_component_get_drvdata(component); 200 201 ucontrol->value.integer.value[0] = wm8960->deemph; 202 return 0; 203 } 204 205 static int wm8960_put_deemph(struct snd_kcontrol *kcontrol, 206 struct snd_ctl_elem_value *ucontrol) 207 { 208 struct snd_soc_component *component = snd_soc_kcontrol_component(kcontrol); 209 struct wm8960_priv *wm8960 = snd_soc_component_get_drvdata(component); 210 unsigned int deemph = ucontrol->value.integer.value[0]; 211 212 if (deemph > 1) 213 return -EINVAL; 214 215 wm8960->deemph = deemph; 216 217 return wm8960_set_deemph(component); 218 } 219 220 static const DECLARE_TLV_DB_SCALE(adc_tlv, -9750, 50, 1); 221 static const DECLARE_TLV_DB_SCALE(inpga_tlv, -1725, 75, 0); 222 static const DECLARE_TLV_DB_SCALE(dac_tlv, -12750, 50, 1); 223 static const DECLARE_TLV_DB_SCALE(bypass_tlv, -2100, 300, 0); 224 static const DECLARE_TLV_DB_SCALE(out_tlv, -12100, 100, 1); 225 static const DECLARE_TLV_DB_SCALE(lineinboost_tlv, -1500, 300, 1); 226 static const SNDRV_CTL_TLVD_DECLARE_DB_RANGE(micboost_tlv, 227 0, 1, TLV_DB_SCALE_ITEM(0, 1300, 0), 228 2, 3, TLV_DB_SCALE_ITEM(2000, 900, 0), 229 ); 230 231 static const struct snd_kcontrol_new wm8960_snd_controls[] = { 232 SOC_DOUBLE_R_TLV("Capture Volume", WM8960_LINVOL, WM8960_RINVOL, 233 0, 63, 0, inpga_tlv), 234 SOC_DOUBLE_R("Capture Volume ZC Switch", WM8960_LINVOL, WM8960_RINVOL, 235 6, 1, 0), 236 SOC_DOUBLE_R("Capture Switch", WM8960_LINVOL, WM8960_RINVOL, 237 7, 1, 1), 238 239 SOC_SINGLE_TLV("Left Input Boost Mixer LINPUT3 Volume", 240 WM8960_INBMIX1, 4, 7, 0, lineinboost_tlv), 241 SOC_SINGLE_TLV("Left Input Boost Mixer LINPUT2 Volume", 242 WM8960_INBMIX1, 1, 7, 0, lineinboost_tlv), 243 SOC_SINGLE_TLV("Right Input Boost Mixer RINPUT3 Volume", 244 WM8960_INBMIX2, 4, 7, 0, lineinboost_tlv), 245 SOC_SINGLE_TLV("Right Input Boost Mixer RINPUT2 Volume", 246 WM8960_INBMIX2, 1, 7, 0, lineinboost_tlv), 247 SOC_SINGLE_TLV("Right Input Boost Mixer RINPUT1 Volume", 248 WM8960_RINPATH, 4, 3, 0, micboost_tlv), 249 SOC_SINGLE_TLV("Left Input Boost Mixer LINPUT1 Volume", 250 WM8960_LINPATH, 4, 3, 0, micboost_tlv), 251 252 SOC_DOUBLE_R_TLV("Playback Volume", WM8960_LDAC, WM8960_RDAC, 253 0, 255, 0, dac_tlv), 254 255 SOC_DOUBLE_R_TLV("Headphone Playback Volume", WM8960_LOUT1, WM8960_ROUT1, 256 0, 127, 0, out_tlv), 257 SOC_DOUBLE_R("Headphone Playback ZC Switch", WM8960_LOUT1, WM8960_ROUT1, 258 7, 1, 0), 259 260 SOC_DOUBLE_R_TLV("Speaker Playback Volume", WM8960_LOUT2, WM8960_ROUT2, 261 0, 127, 0, out_tlv), 262 SOC_DOUBLE_R("Speaker Playback ZC Switch", WM8960_LOUT2, WM8960_ROUT2, 263 7, 1, 0), 264 SOC_SINGLE("Speaker DC Volume", WM8960_CLASSD3, 3, 5, 0), 265 SOC_SINGLE("Speaker AC Volume", WM8960_CLASSD3, 0, 5, 0), 266 267 SOC_SINGLE("PCM Playback -6dB Switch", WM8960_DACCTL1, 7, 1, 0), 268 SOC_ENUM("ADC Polarity", wm8960_enum[0]), 269 SOC_SINGLE("ADC High Pass Filter Switch", WM8960_DACCTL1, 0, 1, 0), 270 271 SOC_ENUM("DAC Polarity", wm8960_enum[1]), 272 SOC_SINGLE_BOOL_EXT("DAC Deemphasis Switch", 0, 273 wm8960_get_deemph, wm8960_put_deemph), 274 275 SOC_ENUM("3D Filter Upper Cut-Off", wm8960_enum[2]), 276 SOC_ENUM("3D Filter Lower Cut-Off", wm8960_enum[3]), 277 SOC_SINGLE("3D Volume", WM8960_3D, 1, 15, 0), 278 SOC_SINGLE("3D Switch", WM8960_3D, 0, 1, 0), 279 280 SOC_ENUM("ALC Function", wm8960_enum[4]), 281 SOC_SINGLE("ALC Max Gain", WM8960_ALC1, 4, 7, 0), 282 SOC_SINGLE("ALC Target", WM8960_ALC1, 0, 15, 1), 283 SOC_SINGLE("ALC Min Gain", WM8960_ALC2, 4, 7, 0), 284 SOC_SINGLE("ALC Hold Time", WM8960_ALC2, 0, 15, 0), 285 SOC_ENUM("ALC Mode", wm8960_enum[5]), 286 SOC_SINGLE("ALC Decay", WM8960_ALC3, 4, 15, 0), 287 SOC_SINGLE("ALC Attack", WM8960_ALC3, 0, 15, 0), 288 289 SOC_SINGLE("Noise Gate Threshold", WM8960_NOISEG, 3, 31, 0), 290 SOC_SINGLE("Noise Gate Switch", WM8960_NOISEG, 0, 1, 0), 291 292 SOC_DOUBLE_R_TLV("ADC PCM Capture Volume", WM8960_LADC, WM8960_RADC, 293 0, 255, 0, adc_tlv), 294 295 SOC_SINGLE_TLV("Left Output Mixer Boost Bypass Volume", 296 WM8960_BYPASS1, 4, 7, 1, bypass_tlv), 297 SOC_SINGLE_TLV("Left Output Mixer LINPUT3 Volume", 298 WM8960_LOUTMIX, 4, 7, 1, bypass_tlv), 299 SOC_SINGLE_TLV("Right Output Mixer Boost Bypass Volume", 300 WM8960_BYPASS2, 4, 7, 1, bypass_tlv), 301 SOC_SINGLE_TLV("Right Output Mixer RINPUT3 Volume", 302 WM8960_ROUTMIX, 4, 7, 1, bypass_tlv), 303 304 SOC_ENUM("ADC Data Output Select", wm8960_enum[6]), 305 SOC_ENUM("DAC Mono Mix", wm8960_enum[7]), 306 }; 307 308 static const struct snd_kcontrol_new wm8960_lin_boost[] = { 309 SOC_DAPM_SINGLE("LINPUT2 Switch", WM8960_LINPATH, 6, 1, 0), 310 SOC_DAPM_SINGLE("LINPUT3 Switch", WM8960_LINPATH, 7, 1, 0), 311 SOC_DAPM_SINGLE("LINPUT1 Switch", WM8960_LINPATH, 8, 1, 0), 312 }; 313 314 static const struct snd_kcontrol_new wm8960_lin[] = { 315 SOC_DAPM_SINGLE("Boost Switch", WM8960_LINPATH, 3, 1, 0), 316 }; 317 318 static const struct snd_kcontrol_new wm8960_rin_boost[] = { 319 SOC_DAPM_SINGLE("RINPUT2 Switch", WM8960_RINPATH, 6, 1, 0), 320 SOC_DAPM_SINGLE("RINPUT3 Switch", WM8960_RINPATH, 7, 1, 0), 321 SOC_DAPM_SINGLE("RINPUT1 Switch", WM8960_RINPATH, 8, 1, 0), 322 }; 323 324 static const struct snd_kcontrol_new wm8960_rin[] = { 325 SOC_DAPM_SINGLE("Boost Switch", WM8960_RINPATH, 3, 1, 0), 326 }; 327 328 static const struct snd_kcontrol_new wm8960_loutput_mixer[] = { 329 SOC_DAPM_SINGLE("PCM Playback Switch", WM8960_LOUTMIX, 8, 1, 0), 330 SOC_DAPM_SINGLE("LINPUT3 Switch", WM8960_LOUTMIX, 7, 1, 0), 331 SOC_DAPM_SINGLE("Boost Bypass Switch", WM8960_BYPASS1, 7, 1, 0), 332 }; 333 334 static const struct snd_kcontrol_new wm8960_routput_mixer[] = { 335 SOC_DAPM_SINGLE("PCM Playback Switch", WM8960_ROUTMIX, 8, 1, 0), 336 SOC_DAPM_SINGLE("RINPUT3 Switch", WM8960_ROUTMIX, 7, 1, 0), 337 SOC_DAPM_SINGLE("Boost Bypass Switch", WM8960_BYPASS2, 7, 1, 0), 338 }; 339 340 static const struct snd_kcontrol_new wm8960_mono_out[] = { 341 SOC_DAPM_SINGLE("Left Switch", WM8960_MONOMIX1, 7, 1, 0), 342 SOC_DAPM_SINGLE("Right Switch", WM8960_MONOMIX2, 7, 1, 0), 343 }; 344 345 static const struct snd_soc_dapm_widget wm8960_dapm_widgets[] = { 346 SND_SOC_DAPM_INPUT("LINPUT1"), 347 SND_SOC_DAPM_INPUT("RINPUT1"), 348 SND_SOC_DAPM_INPUT("LINPUT2"), 349 SND_SOC_DAPM_INPUT("RINPUT2"), 350 SND_SOC_DAPM_INPUT("LINPUT3"), 351 SND_SOC_DAPM_INPUT("RINPUT3"), 352 353 SND_SOC_DAPM_SUPPLY("MICB", WM8960_POWER1, 1, 0, NULL, 0), 354 355 SND_SOC_DAPM_MIXER("Left Boost Mixer", WM8960_POWER1, 5, 0, 356 wm8960_lin_boost, ARRAY_SIZE(wm8960_lin_boost)), 357 SND_SOC_DAPM_MIXER("Right Boost Mixer", WM8960_POWER1, 4, 0, 358 wm8960_rin_boost, ARRAY_SIZE(wm8960_rin_boost)), 359 360 SND_SOC_DAPM_MIXER("Left Input Mixer", WM8960_POWER3, 5, 0, 361 wm8960_lin, ARRAY_SIZE(wm8960_lin)), 362 SND_SOC_DAPM_MIXER("Right Input Mixer", WM8960_POWER3, 4, 0, 363 wm8960_rin, ARRAY_SIZE(wm8960_rin)), 364 365 SND_SOC_DAPM_ADC("Left ADC", "Capture", WM8960_POWER1, 3, 0), 366 SND_SOC_DAPM_ADC("Right ADC", "Capture", WM8960_POWER1, 2, 0), 367 368 SND_SOC_DAPM_DAC("Left DAC", "Playback", WM8960_POWER2, 8, 0), 369 SND_SOC_DAPM_DAC("Right DAC", "Playback", WM8960_POWER2, 7, 0), 370 371 SND_SOC_DAPM_MIXER("Left Output Mixer", WM8960_POWER3, 3, 0, 372 &wm8960_loutput_mixer[0], 373 ARRAY_SIZE(wm8960_loutput_mixer)), 374 SND_SOC_DAPM_MIXER("Right Output Mixer", WM8960_POWER3, 2, 0, 375 &wm8960_routput_mixer[0], 376 ARRAY_SIZE(wm8960_routput_mixer)), 377 378 SND_SOC_DAPM_PGA("LOUT1 PGA", WM8960_POWER2, 6, 0, NULL, 0), 379 SND_SOC_DAPM_PGA("ROUT1 PGA", WM8960_POWER2, 5, 0, NULL, 0), 380 381 SND_SOC_DAPM_PGA("Left Speaker PGA", WM8960_POWER2, 4, 0, NULL, 0), 382 SND_SOC_DAPM_PGA("Right Speaker PGA", WM8960_POWER2, 3, 0, NULL, 0), 383 384 SND_SOC_DAPM_PGA("Right Speaker Output", WM8960_CLASSD1, 7, 0, NULL, 0), 385 SND_SOC_DAPM_PGA("Left Speaker Output", WM8960_CLASSD1, 6, 0, NULL, 0), 386 387 SND_SOC_DAPM_OUTPUT("SPK_LP"), 388 SND_SOC_DAPM_OUTPUT("SPK_LN"), 389 SND_SOC_DAPM_OUTPUT("HP_L"), 390 SND_SOC_DAPM_OUTPUT("HP_R"), 391 SND_SOC_DAPM_OUTPUT("SPK_RP"), 392 SND_SOC_DAPM_OUTPUT("SPK_RN"), 393 SND_SOC_DAPM_OUTPUT("OUT3"), 394 }; 395 396 static const struct snd_soc_dapm_widget wm8960_dapm_widgets_out3[] = { 397 SND_SOC_DAPM_MIXER("Mono Output Mixer", WM8960_POWER2, 1, 0, 398 &wm8960_mono_out[0], 399 ARRAY_SIZE(wm8960_mono_out)), 400 }; 401 402 /* Represent OUT3 as a PGA so that it gets turned on with LOUT1/ROUT1 */ 403 static const struct snd_soc_dapm_widget wm8960_dapm_widgets_capless[] = { 404 SND_SOC_DAPM_PGA("OUT3 VMID", WM8960_POWER2, 1, 0, NULL, 0), 405 }; 406 407 static const struct snd_soc_dapm_route audio_paths[] = { 408 { "Left Boost Mixer", "LINPUT1 Switch", "LINPUT1" }, 409 { "Left Boost Mixer", "LINPUT2 Switch", "LINPUT2" }, 410 { "Left Boost Mixer", "LINPUT3 Switch", "LINPUT3" }, 411 412 { "Left Input Mixer", "Boost Switch", "Left Boost Mixer" }, 413 { "Left Input Mixer", "Boost Switch", "LINPUT1" }, /* Really Boost Switch */ 414 { "Left Input Mixer", NULL, "LINPUT2" }, 415 { "Left Input Mixer", NULL, "LINPUT3" }, 416 417 { "Right Boost Mixer", "RINPUT1 Switch", "RINPUT1" }, 418 { "Right Boost Mixer", "RINPUT2 Switch", "RINPUT2" }, 419 { "Right Boost Mixer", "RINPUT3 Switch", "RINPUT3" }, 420 421 { "Right Input Mixer", "Boost Switch", "Right Boost Mixer" }, 422 { "Right Input Mixer", "Boost Switch", "RINPUT1" }, /* Really Boost Switch */ 423 { "Right Input Mixer", NULL, "RINPUT2" }, 424 { "Right Input Mixer", NULL, "RINPUT3" }, 425 426 { "Left ADC", NULL, "Left Input Mixer" }, 427 { "Right ADC", NULL, "Right Input Mixer" }, 428 429 { "Left Output Mixer", "LINPUT3 Switch", "LINPUT3" }, 430 { "Left Output Mixer", "Boost Bypass Switch", "Left Boost Mixer" }, 431 { "Left Output Mixer", "PCM Playback Switch", "Left DAC" }, 432 433 { "Right Output Mixer", "RINPUT3 Switch", "RINPUT3" }, 434 { "Right Output Mixer", "Boost Bypass Switch", "Right Boost Mixer" }, 435 { "Right Output Mixer", "PCM Playback Switch", "Right DAC" }, 436 437 { "LOUT1 PGA", NULL, "Left Output Mixer" }, 438 { "ROUT1 PGA", NULL, "Right Output Mixer" }, 439 440 { "HP_L", NULL, "LOUT1 PGA" }, 441 { "HP_R", NULL, "ROUT1 PGA" }, 442 443 { "Left Speaker PGA", NULL, "Left Output Mixer" }, 444 { "Right Speaker PGA", NULL, "Right Output Mixer" }, 445 446 { "Left Speaker Output", NULL, "Left Speaker PGA" }, 447 { "Right Speaker Output", NULL, "Right Speaker PGA" }, 448 449 { "SPK_LN", NULL, "Left Speaker Output" }, 450 { "SPK_LP", NULL, "Left Speaker Output" }, 451 { "SPK_RN", NULL, "Right Speaker Output" }, 452 { "SPK_RP", NULL, "Right Speaker Output" }, 453 }; 454 455 static const struct snd_soc_dapm_route audio_paths_out3[] = { 456 { "Mono Output Mixer", "Left Switch", "Left Output Mixer" }, 457 { "Mono Output Mixer", "Right Switch", "Right Output Mixer" }, 458 459 { "OUT3", NULL, "Mono Output Mixer", } 460 }; 461 462 static const struct snd_soc_dapm_route audio_paths_capless[] = { 463 { "HP_L", NULL, "OUT3 VMID" }, 464 { "HP_R", NULL, "OUT3 VMID" }, 465 466 { "OUT3 VMID", NULL, "Left Output Mixer" }, 467 { "OUT3 VMID", NULL, "Right Output Mixer" }, 468 }; 469 470 static int wm8960_add_widgets(struct snd_soc_component *component) 471 { 472 struct wm8960_priv *wm8960 = snd_soc_component_get_drvdata(component); 473 struct wm8960_data *pdata = &wm8960->pdata; 474 struct snd_soc_dapm_context *dapm = snd_soc_component_get_dapm(component); 475 struct snd_soc_dapm_widget *w; 476 477 snd_soc_dapm_new_controls(dapm, wm8960_dapm_widgets, 478 ARRAY_SIZE(wm8960_dapm_widgets)); 479 480 snd_soc_dapm_add_routes(dapm, audio_paths, ARRAY_SIZE(audio_paths)); 481 482 /* In capless mode OUT3 is used to provide VMID for the 483 * headphone outputs, otherwise it is used as a mono mixer. 484 */ 485 if (pdata && pdata->capless) { 486 snd_soc_dapm_new_controls(dapm, wm8960_dapm_widgets_capless, 487 ARRAY_SIZE(wm8960_dapm_widgets_capless)); 488 489 snd_soc_dapm_add_routes(dapm, audio_paths_capless, 490 ARRAY_SIZE(audio_paths_capless)); 491 } else { 492 snd_soc_dapm_new_controls(dapm, wm8960_dapm_widgets_out3, 493 ARRAY_SIZE(wm8960_dapm_widgets_out3)); 494 495 snd_soc_dapm_add_routes(dapm, audio_paths_out3, 496 ARRAY_SIZE(audio_paths_out3)); 497 } 498 499 /* We need to power up the headphone output stage out of 500 * sequence for capless mode. To save scanning the widget 501 * list each time to find the desired power state do so now 502 * and save the result. 503 */ 504 list_for_each_entry(w, &component->card->widgets, list) { 505 if (w->dapm != dapm) 506 continue; 507 if (strcmp(w->name, "LOUT1 PGA") == 0) 508 wm8960->lout1 = w; 509 if (strcmp(w->name, "ROUT1 PGA") == 0) 510 wm8960->rout1 = w; 511 if (strcmp(w->name, "OUT3 VMID") == 0) 512 wm8960->out3 = w; 513 } 514 515 return 0; 516 } 517 518 static int wm8960_set_dai_fmt(struct snd_soc_dai *codec_dai, 519 unsigned int fmt) 520 { 521 struct snd_soc_component *component = codec_dai->component; 522 u16 iface = 0; 523 524 /* set master/slave audio interface */ 525 switch (fmt & SND_SOC_DAIFMT_MASTER_MASK) { 526 case SND_SOC_DAIFMT_CBM_CFM: 527 iface |= 0x0040; 528 break; 529 case SND_SOC_DAIFMT_CBS_CFS: 530 break; 531 default: 532 return -EINVAL; 533 } 534 535 /* interface format */ 536 switch (fmt & SND_SOC_DAIFMT_FORMAT_MASK) { 537 case SND_SOC_DAIFMT_I2S: 538 iface |= 0x0002; 539 break; 540 case SND_SOC_DAIFMT_RIGHT_J: 541 break; 542 case SND_SOC_DAIFMT_LEFT_J: 543 iface |= 0x0001; 544 break; 545 case SND_SOC_DAIFMT_DSP_A: 546 iface |= 0x0003; 547 break; 548 case SND_SOC_DAIFMT_DSP_B: 549 iface |= 0x0013; 550 break; 551 default: 552 return -EINVAL; 553 } 554 555 /* clock inversion */ 556 switch (fmt & SND_SOC_DAIFMT_INV_MASK) { 557 case SND_SOC_DAIFMT_NB_NF: 558 break; 559 case SND_SOC_DAIFMT_IB_IF: 560 iface |= 0x0090; 561 break; 562 case SND_SOC_DAIFMT_IB_NF: 563 iface |= 0x0080; 564 break; 565 case SND_SOC_DAIFMT_NB_IF: 566 iface |= 0x0010; 567 break; 568 default: 569 return -EINVAL; 570 } 571 572 /* set iface */ 573 snd_soc_component_write(component, WM8960_IFACE1, iface); 574 return 0; 575 } 576 577 static struct { 578 int rate; 579 unsigned int val; 580 } alc_rates[] = { 581 { 48000, 0 }, 582 { 44100, 0 }, 583 { 32000, 1 }, 584 { 22050, 2 }, 585 { 24000, 2 }, 586 { 16000, 3 }, 587 { 11025, 4 }, 588 { 12000, 4 }, 589 { 8000, 5 }, 590 }; 591 592 /* -1 for reserved value */ 593 static const int sysclk_divs[] = { 1, -1, 2, -1 }; 594 595 /* Multiply 256 for internal 256 div */ 596 static const int dac_divs[] = { 256, 384, 512, 768, 1024, 1408, 1536 }; 597 598 /* Multiply 10 to eliminate decimials */ 599 static const int bclk_divs[] = { 600 10, 15, 20, 30, 40, 55, 60, 80, 110, 601 120, 160, 220, 240, 320, 320, 320 602 }; 603 604 /** 605 * wm8960_configure_sysclk - checks if there is a sysclk frequency available 606 * The sysclk must be chosen such that: 607 * - sysclk = MCLK / sysclk_divs 608 * - lrclk = sysclk / dac_divs 609 * - 10 * bclk = sysclk / bclk_divs 610 * 611 * @wm8960: codec private data 612 * @mclk: MCLK used to derive sysclk 613 * @sysclk_idx: sysclk_divs index for found sysclk 614 * @dac_idx: dac_divs index for found lrclk 615 * @bclk_idx: bclk_divs index for found bclk 616 * 617 * Returns: 618 * -1, in case no sysclk frequency available found 619 * >=0, in case we could derive bclk and lrclk from sysclk using 620 * (@sysclk_idx, @dac_idx, @bclk_idx) dividers 621 */ 622 static 623 int wm8960_configure_sysclk(struct wm8960_priv *wm8960, int mclk, 624 int *sysclk_idx, int *dac_idx, int *bclk_idx) 625 { 626 int sysclk, bclk, lrclk; 627 int i, j, k; 628 int diff; 629 630 /* marker for no match */ 631 *bclk_idx = -1; 632 633 bclk = wm8960->bclk; 634 lrclk = wm8960->lrclk; 635 636 /* check if the sysclk frequency is available. */ 637 for (i = 0; i < ARRAY_SIZE(sysclk_divs); ++i) { 638 if (sysclk_divs[i] == -1) 639 continue; 640 sysclk = mclk / sysclk_divs[i]; 641 for (j = 0; j < ARRAY_SIZE(dac_divs); ++j) { 642 if (sysclk != dac_divs[j] * lrclk) 643 continue; 644 for (k = 0; k < ARRAY_SIZE(bclk_divs); ++k) { 645 diff = sysclk - bclk * bclk_divs[k] / 10; 646 if (diff == 0) { 647 *sysclk_idx = i; 648 *dac_idx = j; 649 *bclk_idx = k; 650 break; 651 } 652 } 653 if (k != ARRAY_SIZE(bclk_divs)) 654 break; 655 } 656 if (j != ARRAY_SIZE(dac_divs)) 657 break; 658 } 659 return *bclk_idx; 660 } 661 662 /** 663 * wm8960_configure_pll - checks if there is a PLL out frequency available 664 * The PLL out frequency must be chosen such that: 665 * - sysclk = lrclk * dac_divs 666 * - freq_out = sysclk * sysclk_divs 667 * - 10 * sysclk = bclk * bclk_divs 668 * 669 * If we cannot find an exact match for (sysclk, lrclk, bclk) 670 * triplet, we relax the bclk such that bclk is chosen as the 671 * closest available frequency greater than expected bclk. 672 * 673 * @component: component structure 674 * @freq_in: input frequency used to derive freq out via PLL 675 * @sysclk_idx: sysclk_divs index for found sysclk 676 * @dac_idx: dac_divs index for found lrclk 677 * @bclk_idx: bclk_divs index for found bclk 678 * 679 * Returns: 680 * < 0, in case no PLL frequency out available was found 681 * >=0, in case we could derive bclk, lrclk, sysclk from PLL out using 682 * (@sysclk_idx, @dac_idx, @bclk_idx) dividers 683 */ 684 static 685 int wm8960_configure_pll(struct snd_soc_component *component, int freq_in, 686 int *sysclk_idx, int *dac_idx, int *bclk_idx) 687 { 688 struct wm8960_priv *wm8960 = snd_soc_component_get_drvdata(component); 689 int sysclk, bclk, lrclk, freq_out; 690 int diff, closest, best_freq_out; 691 int i, j, k; 692 693 bclk = wm8960->bclk; 694 lrclk = wm8960->lrclk; 695 closest = freq_in; 696 697 best_freq_out = -EINVAL; 698 *sysclk_idx = *dac_idx = *bclk_idx = -1; 699 700 /* 701 * From Datasheet, the PLL performs best when f2 is between 702 * 90MHz and 100MHz, the desired sysclk output is 11.2896MHz 703 * or 12.288MHz, then sysclkdiv = 2 is the best choice. 704 * So search sysclk_divs from 2 to 1 other than from 1 to 2. 705 */ 706 for (i = ARRAY_SIZE(sysclk_divs) - 1; i >= 0; --i) { 707 if (sysclk_divs[i] == -1) 708 continue; 709 for (j = 0; j < ARRAY_SIZE(dac_divs); ++j) { 710 sysclk = lrclk * dac_divs[j]; 711 freq_out = sysclk * sysclk_divs[i]; 712 713 for (k = 0; k < ARRAY_SIZE(bclk_divs); ++k) { 714 if (!is_pll_freq_available(freq_in, freq_out)) 715 continue; 716 717 diff = sysclk - bclk * bclk_divs[k] / 10; 718 if (diff == 0) { 719 *sysclk_idx = i; 720 *dac_idx = j; 721 *bclk_idx = k; 722 return freq_out; 723 } 724 if (diff > 0 && closest > diff) { 725 *sysclk_idx = i; 726 *dac_idx = j; 727 *bclk_idx = k; 728 closest = diff; 729 best_freq_out = freq_out; 730 } 731 } 732 } 733 } 734 735 return best_freq_out; 736 } 737 static int wm8960_configure_clocking(struct snd_soc_component *component) 738 { 739 struct wm8960_priv *wm8960 = snd_soc_component_get_drvdata(component); 740 int freq_out, freq_in; 741 u16 iface1 = snd_soc_component_read(component, WM8960_IFACE1); 742 int i, j, k; 743 int ret; 744 745 /* 746 * For Slave mode clocking should still be configured, 747 * so this if statement should be removed, but some platform 748 * may not work if the sysclk is not configured, to avoid such 749 * compatible issue, just add '!wm8960->sysclk' condition in 750 * this if statement. 751 */ 752 if (!(iface1 & (1 << 6)) && !wm8960->sysclk) { 753 dev_warn(component->dev, 754 "slave mode, but proceeding with no clock configuration\n"); 755 return 0; 756 } 757 758 if (wm8960->clk_id != WM8960_SYSCLK_MCLK && !wm8960->freq_in) { 759 dev_err(component->dev, "No MCLK configured\n"); 760 return -EINVAL; 761 } 762 763 freq_in = wm8960->freq_in; 764 /* 765 * If it's sysclk auto mode, check if the MCLK can provide sysclk or 766 * not. If MCLK can provide sysclk, using MCLK to provide sysclk 767 * directly. Otherwise, auto select a available pll out frequency 768 * and set PLL. 769 */ 770 if (wm8960->clk_id == WM8960_SYSCLK_AUTO) { 771 /* disable the PLL and using MCLK to provide sysclk */ 772 wm8960_set_pll(component, 0, 0); 773 freq_out = freq_in; 774 } else if (wm8960->sysclk) { 775 freq_out = wm8960->sysclk; 776 } else { 777 dev_err(component->dev, "No SYSCLK configured\n"); 778 return -EINVAL; 779 } 780 781 if (wm8960->clk_id != WM8960_SYSCLK_PLL) { 782 ret = wm8960_configure_sysclk(wm8960, freq_out, &i, &j, &k); 783 if (ret >= 0) { 784 goto configure_clock; 785 } else if (wm8960->clk_id != WM8960_SYSCLK_AUTO) { 786 dev_err(component->dev, "failed to configure clock\n"); 787 return -EINVAL; 788 } 789 } 790 791 freq_out = wm8960_configure_pll(component, freq_in, &i, &j, &k); 792 if (freq_out < 0) { 793 dev_err(component->dev, "failed to configure clock via PLL\n"); 794 return freq_out; 795 } 796 wm8960_set_pll(component, freq_in, freq_out); 797 798 configure_clock: 799 /* configure sysclk clock */ 800 snd_soc_component_update_bits(component, WM8960_CLOCK1, 3 << 1, i << 1); 801 802 /* configure frame clock */ 803 snd_soc_component_update_bits(component, WM8960_CLOCK1, 0x7 << 3, j << 3); 804 snd_soc_component_update_bits(component, WM8960_CLOCK1, 0x7 << 6, j << 6); 805 806 /* configure bit clock */ 807 snd_soc_component_update_bits(component, WM8960_CLOCK2, 0xf, k); 808 809 return 0; 810 } 811 812 static int wm8960_hw_params(struct snd_pcm_substream *substream, 813 struct snd_pcm_hw_params *params, 814 struct snd_soc_dai *dai) 815 { 816 struct snd_soc_component *component = dai->component; 817 struct wm8960_priv *wm8960 = snd_soc_component_get_drvdata(component); 818 u16 iface = snd_soc_component_read(component, WM8960_IFACE1) & 0xfff3; 819 bool tx = substream->stream == SNDRV_PCM_STREAM_PLAYBACK; 820 int i; 821 822 wm8960->bclk = snd_soc_params_to_bclk(params); 823 if (params_channels(params) == 1) 824 wm8960->bclk *= 2; 825 826 /* bit size */ 827 switch (params_width(params)) { 828 case 16: 829 break; 830 case 20: 831 iface |= 0x0004; 832 break; 833 case 24: 834 iface |= 0x0008; 835 break; 836 case 32: 837 /* right justify mode does not support 32 word length */ 838 if ((iface & 0x3) != 0) { 839 iface |= 0x000c; 840 break; 841 } 842 fallthrough; 843 default: 844 dev_err(component->dev, "unsupported width %d\n", 845 params_width(params)); 846 return -EINVAL; 847 } 848 849 wm8960->lrclk = params_rate(params); 850 /* Update filters for the new rate */ 851 if (tx) { 852 wm8960_set_deemph(component); 853 } else { 854 for (i = 0; i < ARRAY_SIZE(alc_rates); i++) 855 if (alc_rates[i].rate == params_rate(params)) 856 snd_soc_component_update_bits(component, 857 WM8960_ADDCTL3, 0x7, 858 alc_rates[i].val); 859 } 860 861 /* set iface */ 862 snd_soc_component_write(component, WM8960_IFACE1, iface); 863 864 wm8960->is_stream_in_use[tx] = true; 865 866 if (!wm8960->is_stream_in_use[!tx]) 867 return wm8960_configure_clocking(component); 868 869 return 0; 870 } 871 872 static int wm8960_hw_free(struct snd_pcm_substream *substream, 873 struct snd_soc_dai *dai) 874 { 875 struct snd_soc_component *component = dai->component; 876 struct wm8960_priv *wm8960 = snd_soc_component_get_drvdata(component); 877 bool tx = substream->stream == SNDRV_PCM_STREAM_PLAYBACK; 878 879 wm8960->is_stream_in_use[tx] = false; 880 881 return 0; 882 } 883 884 static int wm8960_mute(struct snd_soc_dai *dai, int mute, int direction) 885 { 886 struct snd_soc_component *component = dai->component; 887 888 if (mute) 889 snd_soc_component_update_bits(component, WM8960_DACCTL1, 0x8, 0x8); 890 else 891 snd_soc_component_update_bits(component, WM8960_DACCTL1, 0x8, 0); 892 return 0; 893 } 894 895 static int wm8960_set_bias_level_out3(struct snd_soc_component *component, 896 enum snd_soc_bias_level level) 897 { 898 struct wm8960_priv *wm8960 = snd_soc_component_get_drvdata(component); 899 u16 pm2 = snd_soc_component_read(component, WM8960_POWER2); 900 int ret; 901 902 switch (level) { 903 case SND_SOC_BIAS_ON: 904 break; 905 906 case SND_SOC_BIAS_PREPARE: 907 switch (snd_soc_component_get_bias_level(component)) { 908 case SND_SOC_BIAS_STANDBY: 909 if (!IS_ERR(wm8960->mclk)) { 910 ret = clk_prepare_enable(wm8960->mclk); 911 if (ret) { 912 dev_err(component->dev, 913 "Failed to enable MCLK: %d\n", 914 ret); 915 return ret; 916 } 917 } 918 919 ret = wm8960_configure_clocking(component); 920 if (ret) 921 return ret; 922 923 /* Set VMID to 2x50k */ 924 snd_soc_component_update_bits(component, WM8960_POWER1, 0x180, 0x80); 925 break; 926 927 case SND_SOC_BIAS_ON: 928 /* 929 * If it's sysclk auto mode, and the pll is enabled, 930 * disable the pll 931 */ 932 if (wm8960->clk_id == WM8960_SYSCLK_AUTO && (pm2 & 0x1)) 933 wm8960_set_pll(component, 0, 0); 934 935 if (!IS_ERR(wm8960->mclk)) 936 clk_disable_unprepare(wm8960->mclk); 937 break; 938 939 default: 940 break; 941 } 942 943 break; 944 945 case SND_SOC_BIAS_STANDBY: 946 if (snd_soc_component_get_bias_level(component) == SND_SOC_BIAS_OFF) { 947 regcache_sync(wm8960->regmap); 948 949 /* Enable anti-pop features */ 950 snd_soc_component_write(component, WM8960_APOP1, 951 WM8960_POBCTRL | WM8960_SOFT_ST | 952 WM8960_BUFDCOPEN | WM8960_BUFIOEN); 953 954 /* Enable & ramp VMID at 2x50k */ 955 snd_soc_component_update_bits(component, WM8960_POWER1, 0x80, 0x80); 956 msleep(100); 957 958 /* Enable VREF */ 959 snd_soc_component_update_bits(component, WM8960_POWER1, WM8960_VREF, 960 WM8960_VREF); 961 962 /* Disable anti-pop features */ 963 snd_soc_component_write(component, WM8960_APOP1, WM8960_BUFIOEN); 964 } 965 966 /* Set VMID to 2x250k */ 967 snd_soc_component_update_bits(component, WM8960_POWER1, 0x180, 0x100); 968 break; 969 970 case SND_SOC_BIAS_OFF: 971 /* Enable anti-pop features */ 972 snd_soc_component_write(component, WM8960_APOP1, 973 WM8960_POBCTRL | WM8960_SOFT_ST | 974 WM8960_BUFDCOPEN | WM8960_BUFIOEN); 975 976 /* Disable VMID and VREF, let them discharge */ 977 snd_soc_component_write(component, WM8960_POWER1, 0); 978 msleep(600); 979 break; 980 } 981 982 return 0; 983 } 984 985 static int wm8960_set_bias_level_capless(struct snd_soc_component *component, 986 enum snd_soc_bias_level level) 987 { 988 struct wm8960_priv *wm8960 = snd_soc_component_get_drvdata(component); 989 u16 pm2 = snd_soc_component_read(component, WM8960_POWER2); 990 int reg, ret; 991 992 switch (level) { 993 case SND_SOC_BIAS_ON: 994 break; 995 996 case SND_SOC_BIAS_PREPARE: 997 switch (snd_soc_component_get_bias_level(component)) { 998 case SND_SOC_BIAS_STANDBY: 999 /* Enable anti pop mode */ 1000 snd_soc_component_update_bits(component, WM8960_APOP1, 1001 WM8960_POBCTRL | WM8960_SOFT_ST | 1002 WM8960_BUFDCOPEN, 1003 WM8960_POBCTRL | WM8960_SOFT_ST | 1004 WM8960_BUFDCOPEN); 1005 1006 /* Enable LOUT1, ROUT1 and OUT3 if they're enabled */ 1007 reg = 0; 1008 if (wm8960->lout1 && wm8960->lout1->power) 1009 reg |= WM8960_PWR2_LOUT1; 1010 if (wm8960->rout1 && wm8960->rout1->power) 1011 reg |= WM8960_PWR2_ROUT1; 1012 if (wm8960->out3 && wm8960->out3->power) 1013 reg |= WM8960_PWR2_OUT3; 1014 snd_soc_component_update_bits(component, WM8960_POWER2, 1015 WM8960_PWR2_LOUT1 | 1016 WM8960_PWR2_ROUT1 | 1017 WM8960_PWR2_OUT3, reg); 1018 1019 /* Enable VMID at 2*50k */ 1020 snd_soc_component_update_bits(component, WM8960_POWER1, 1021 WM8960_VMID_MASK, 0x80); 1022 1023 /* Ramp */ 1024 msleep(100); 1025 1026 /* Enable VREF */ 1027 snd_soc_component_update_bits(component, WM8960_POWER1, 1028 WM8960_VREF, WM8960_VREF); 1029 1030 msleep(100); 1031 1032 if (!IS_ERR(wm8960->mclk)) { 1033 ret = clk_prepare_enable(wm8960->mclk); 1034 if (ret) { 1035 dev_err(component->dev, 1036 "Failed to enable MCLK: %d\n", 1037 ret); 1038 return ret; 1039 } 1040 } 1041 1042 ret = wm8960_configure_clocking(component); 1043 if (ret) 1044 return ret; 1045 1046 break; 1047 1048 case SND_SOC_BIAS_ON: 1049 /* 1050 * If it's sysclk auto mode, and the pll is enabled, 1051 * disable the pll 1052 */ 1053 if (wm8960->clk_id == WM8960_SYSCLK_AUTO && (pm2 & 0x1)) 1054 wm8960_set_pll(component, 0, 0); 1055 1056 if (!IS_ERR(wm8960->mclk)) 1057 clk_disable_unprepare(wm8960->mclk); 1058 1059 /* Enable anti-pop mode */ 1060 snd_soc_component_update_bits(component, WM8960_APOP1, 1061 WM8960_POBCTRL | WM8960_SOFT_ST | 1062 WM8960_BUFDCOPEN, 1063 WM8960_POBCTRL | WM8960_SOFT_ST | 1064 WM8960_BUFDCOPEN); 1065 1066 /* Disable VMID and VREF */ 1067 snd_soc_component_update_bits(component, WM8960_POWER1, 1068 WM8960_VREF | WM8960_VMID_MASK, 0); 1069 break; 1070 1071 case SND_SOC_BIAS_OFF: 1072 regcache_sync(wm8960->regmap); 1073 break; 1074 default: 1075 break; 1076 } 1077 break; 1078 1079 case SND_SOC_BIAS_STANDBY: 1080 switch (snd_soc_component_get_bias_level(component)) { 1081 case SND_SOC_BIAS_PREPARE: 1082 /* Disable HP discharge */ 1083 snd_soc_component_update_bits(component, WM8960_APOP2, 1084 WM8960_DISOP | WM8960_DRES_MASK, 1085 0); 1086 1087 /* Disable anti-pop features */ 1088 snd_soc_component_update_bits(component, WM8960_APOP1, 1089 WM8960_POBCTRL | WM8960_SOFT_ST | 1090 WM8960_BUFDCOPEN, 1091 WM8960_POBCTRL | WM8960_SOFT_ST | 1092 WM8960_BUFDCOPEN); 1093 break; 1094 1095 default: 1096 break; 1097 } 1098 break; 1099 1100 case SND_SOC_BIAS_OFF: 1101 break; 1102 } 1103 1104 return 0; 1105 } 1106 1107 /* PLL divisors */ 1108 struct _pll_div { 1109 u32 pre_div:1; 1110 u32 n:4; 1111 u32 k:24; 1112 }; 1113 1114 static bool is_pll_freq_available(unsigned int source, unsigned int target) 1115 { 1116 unsigned int Ndiv; 1117 1118 if (source == 0 || target == 0) 1119 return false; 1120 1121 /* Scale up target to PLL operating frequency */ 1122 target *= 4; 1123 Ndiv = target / source; 1124 1125 if (Ndiv < 6) { 1126 source >>= 1; 1127 Ndiv = target / source; 1128 } 1129 1130 if ((Ndiv < 6) || (Ndiv > 12)) 1131 return false; 1132 1133 return true; 1134 } 1135 1136 /* The size in bits of the pll divide multiplied by 10 1137 * to allow rounding later */ 1138 #define FIXED_PLL_SIZE ((1 << 24) * 10) 1139 1140 static int pll_factors(unsigned int source, unsigned int target, 1141 struct _pll_div *pll_div) 1142 { 1143 unsigned long long Kpart; 1144 unsigned int K, Ndiv, Nmod; 1145 1146 pr_debug("WM8960 PLL: setting %dHz->%dHz\n", source, target); 1147 1148 /* Scale up target to PLL operating frequency */ 1149 target *= 4; 1150 1151 Ndiv = target / source; 1152 if (Ndiv < 6) { 1153 source >>= 1; 1154 pll_div->pre_div = 1; 1155 Ndiv = target / source; 1156 } else 1157 pll_div->pre_div = 0; 1158 1159 if ((Ndiv < 6) || (Ndiv > 12)) { 1160 pr_err("WM8960 PLL: Unsupported N=%d\n", Ndiv); 1161 return -EINVAL; 1162 } 1163 1164 pll_div->n = Ndiv; 1165 Nmod = target % source; 1166 Kpart = FIXED_PLL_SIZE * (long long)Nmod; 1167 1168 do_div(Kpart, source); 1169 1170 K = Kpart & 0xFFFFFFFF; 1171 1172 /* Check if we need to round */ 1173 if ((K % 10) >= 5) 1174 K += 5; 1175 1176 /* Move down to proper range now rounding is done */ 1177 K /= 10; 1178 1179 pll_div->k = K; 1180 1181 pr_debug("WM8960 PLL: N=%x K=%x pre_div=%d\n", 1182 pll_div->n, pll_div->k, pll_div->pre_div); 1183 1184 return 0; 1185 } 1186 1187 static int wm8960_set_pll(struct snd_soc_component *component, 1188 unsigned int freq_in, unsigned int freq_out) 1189 { 1190 u16 reg; 1191 static struct _pll_div pll_div; 1192 int ret; 1193 1194 if (freq_in && freq_out) { 1195 ret = pll_factors(freq_in, freq_out, &pll_div); 1196 if (ret != 0) 1197 return ret; 1198 } 1199 1200 /* Disable the PLL: even if we are changing the frequency the 1201 * PLL needs to be disabled while we do so. */ 1202 snd_soc_component_update_bits(component, WM8960_CLOCK1, 0x1, 0); 1203 snd_soc_component_update_bits(component, WM8960_POWER2, 0x1, 0); 1204 1205 if (!freq_in || !freq_out) 1206 return 0; 1207 1208 reg = snd_soc_component_read(component, WM8960_PLL1) & ~0x3f; 1209 reg |= pll_div.pre_div << 4; 1210 reg |= pll_div.n; 1211 1212 if (pll_div.k) { 1213 reg |= 0x20; 1214 1215 snd_soc_component_write(component, WM8960_PLL2, (pll_div.k >> 16) & 0xff); 1216 snd_soc_component_write(component, WM8960_PLL3, (pll_div.k >> 8) & 0xff); 1217 snd_soc_component_write(component, WM8960_PLL4, pll_div.k & 0xff); 1218 } 1219 snd_soc_component_write(component, WM8960_PLL1, reg); 1220 1221 /* Turn it on */ 1222 snd_soc_component_update_bits(component, WM8960_POWER2, 0x1, 0x1); 1223 msleep(250); 1224 snd_soc_component_update_bits(component, WM8960_CLOCK1, 0x1, 0x1); 1225 1226 return 0; 1227 } 1228 1229 static int wm8960_set_dai_pll(struct snd_soc_dai *codec_dai, int pll_id, 1230 int source, unsigned int freq_in, unsigned int freq_out) 1231 { 1232 struct snd_soc_component *component = codec_dai->component; 1233 struct wm8960_priv *wm8960 = snd_soc_component_get_drvdata(component); 1234 1235 wm8960->freq_in = freq_in; 1236 1237 if (pll_id == WM8960_SYSCLK_AUTO) 1238 return 0; 1239 1240 return wm8960_set_pll(component, freq_in, freq_out); 1241 } 1242 1243 static int wm8960_set_dai_clkdiv(struct snd_soc_dai *codec_dai, 1244 int div_id, int div) 1245 { 1246 struct snd_soc_component *component = codec_dai->component; 1247 u16 reg; 1248 1249 switch (div_id) { 1250 case WM8960_SYSCLKDIV: 1251 reg = snd_soc_component_read(component, WM8960_CLOCK1) & 0x1f9; 1252 snd_soc_component_write(component, WM8960_CLOCK1, reg | div); 1253 break; 1254 case WM8960_DACDIV: 1255 reg = snd_soc_component_read(component, WM8960_CLOCK1) & 0x1c7; 1256 snd_soc_component_write(component, WM8960_CLOCK1, reg | div); 1257 break; 1258 case WM8960_OPCLKDIV: 1259 reg = snd_soc_component_read(component, WM8960_PLL1) & 0x03f; 1260 snd_soc_component_write(component, WM8960_PLL1, reg | div); 1261 break; 1262 case WM8960_DCLKDIV: 1263 reg = snd_soc_component_read(component, WM8960_CLOCK2) & 0x03f; 1264 snd_soc_component_write(component, WM8960_CLOCK2, reg | div); 1265 break; 1266 case WM8960_TOCLKSEL: 1267 reg = snd_soc_component_read(component, WM8960_ADDCTL1) & 0x1fd; 1268 snd_soc_component_write(component, WM8960_ADDCTL1, reg | div); 1269 break; 1270 default: 1271 return -EINVAL; 1272 } 1273 1274 return 0; 1275 } 1276 1277 static int wm8960_set_bias_level(struct snd_soc_component *component, 1278 enum snd_soc_bias_level level) 1279 { 1280 struct wm8960_priv *wm8960 = snd_soc_component_get_drvdata(component); 1281 1282 return wm8960->set_bias_level(component, level); 1283 } 1284 1285 static int wm8960_set_dai_sysclk(struct snd_soc_dai *dai, int clk_id, 1286 unsigned int freq, int dir) 1287 { 1288 struct snd_soc_component *component = dai->component; 1289 struct wm8960_priv *wm8960 = snd_soc_component_get_drvdata(component); 1290 1291 switch (clk_id) { 1292 case WM8960_SYSCLK_MCLK: 1293 snd_soc_component_update_bits(component, WM8960_CLOCK1, 1294 0x1, WM8960_SYSCLK_MCLK); 1295 break; 1296 case WM8960_SYSCLK_PLL: 1297 snd_soc_component_update_bits(component, WM8960_CLOCK1, 1298 0x1, WM8960_SYSCLK_PLL); 1299 break; 1300 case WM8960_SYSCLK_AUTO: 1301 break; 1302 default: 1303 return -EINVAL; 1304 } 1305 1306 wm8960->sysclk = freq; 1307 wm8960->clk_id = clk_id; 1308 1309 return 0; 1310 } 1311 1312 #define WM8960_RATES SNDRV_PCM_RATE_8000_48000 1313 1314 #define WM8960_FORMATS \ 1315 (SNDRV_PCM_FMTBIT_S16_LE | SNDRV_PCM_FMTBIT_S20_3LE | \ 1316 SNDRV_PCM_FMTBIT_S24_LE | SNDRV_PCM_FMTBIT_S32_LE) 1317 1318 static const struct snd_soc_dai_ops wm8960_dai_ops = { 1319 .hw_params = wm8960_hw_params, 1320 .hw_free = wm8960_hw_free, 1321 .mute_stream = wm8960_mute, 1322 .set_fmt = wm8960_set_dai_fmt, 1323 .set_clkdiv = wm8960_set_dai_clkdiv, 1324 .set_pll = wm8960_set_dai_pll, 1325 .set_sysclk = wm8960_set_dai_sysclk, 1326 .no_capture_mute = 1, 1327 }; 1328 1329 static struct snd_soc_dai_driver wm8960_dai = { 1330 .name = "wm8960-hifi", 1331 .playback = { 1332 .stream_name = "Playback", 1333 .channels_min = 1, 1334 .channels_max = 2, 1335 .rates = WM8960_RATES, 1336 .formats = WM8960_FORMATS,}, 1337 .capture = { 1338 .stream_name = "Capture", 1339 .channels_min = 1, 1340 .channels_max = 2, 1341 .rates = WM8960_RATES, 1342 .formats = WM8960_FORMATS,}, 1343 .ops = &wm8960_dai_ops, 1344 .symmetric_rate = 1, 1345 }; 1346 1347 static int wm8960_probe(struct snd_soc_component *component) 1348 { 1349 struct wm8960_priv *wm8960 = snd_soc_component_get_drvdata(component); 1350 struct wm8960_data *pdata = &wm8960->pdata; 1351 1352 if (pdata->capless) 1353 wm8960->set_bias_level = wm8960_set_bias_level_capless; 1354 else 1355 wm8960->set_bias_level = wm8960_set_bias_level_out3; 1356 1357 snd_soc_add_component_controls(component, wm8960_snd_controls, 1358 ARRAY_SIZE(wm8960_snd_controls)); 1359 wm8960_add_widgets(component); 1360 1361 return 0; 1362 } 1363 1364 static const struct snd_soc_component_driver soc_component_dev_wm8960 = { 1365 .probe = wm8960_probe, 1366 .set_bias_level = wm8960_set_bias_level, 1367 .suspend_bias_off = 1, 1368 .idle_bias_on = 1, 1369 .use_pmdown_time = 1, 1370 .endianness = 1, 1371 .non_legacy_dai_naming = 1, 1372 }; 1373 1374 static const struct regmap_config wm8960_regmap = { 1375 .reg_bits = 7, 1376 .val_bits = 9, 1377 .max_register = WM8960_PLL4, 1378 1379 .reg_defaults = wm8960_reg_defaults, 1380 .num_reg_defaults = ARRAY_SIZE(wm8960_reg_defaults), 1381 .cache_type = REGCACHE_RBTREE, 1382 1383 .volatile_reg = wm8960_volatile, 1384 }; 1385 1386 static void wm8960_set_pdata_from_of(struct i2c_client *i2c, 1387 struct wm8960_data *pdata) 1388 { 1389 const struct device_node *np = i2c->dev.of_node; 1390 1391 if (of_property_read_bool(np, "wlf,capless")) 1392 pdata->capless = true; 1393 1394 if (of_property_read_bool(np, "wlf,shared-lrclk")) 1395 pdata->shared_lrclk = true; 1396 1397 of_property_read_u32_array(np, "wlf,gpio-cfg", pdata->gpio_cfg, 1398 ARRAY_SIZE(pdata->gpio_cfg)); 1399 1400 of_property_read_u32_array(np, "wlf,hp-cfg", pdata->hp_cfg, 1401 ARRAY_SIZE(pdata->hp_cfg)); 1402 } 1403 1404 static int wm8960_i2c_probe(struct i2c_client *i2c, 1405 const struct i2c_device_id *id) 1406 { 1407 struct wm8960_data *pdata = dev_get_platdata(&i2c->dev); 1408 struct wm8960_priv *wm8960; 1409 int ret; 1410 1411 wm8960 = devm_kzalloc(&i2c->dev, sizeof(struct wm8960_priv), 1412 GFP_KERNEL); 1413 if (wm8960 == NULL) 1414 return -ENOMEM; 1415 1416 wm8960->mclk = devm_clk_get(&i2c->dev, "mclk"); 1417 if (IS_ERR(wm8960->mclk)) { 1418 if (PTR_ERR(wm8960->mclk) == -EPROBE_DEFER) 1419 return -EPROBE_DEFER; 1420 } 1421 1422 wm8960->regmap = devm_regmap_init_i2c(i2c, &wm8960_regmap); 1423 if (IS_ERR(wm8960->regmap)) 1424 return PTR_ERR(wm8960->regmap); 1425 1426 if (pdata) 1427 memcpy(&wm8960->pdata, pdata, sizeof(struct wm8960_data)); 1428 else if (i2c->dev.of_node) 1429 wm8960_set_pdata_from_of(i2c, &wm8960->pdata); 1430 1431 ret = wm8960_reset(wm8960->regmap); 1432 if (ret != 0) { 1433 dev_err(&i2c->dev, "Failed to issue reset\n"); 1434 return ret; 1435 } 1436 1437 if (wm8960->pdata.shared_lrclk) { 1438 ret = regmap_update_bits(wm8960->regmap, WM8960_ADDCTL2, 1439 0x4, 0x4); 1440 if (ret != 0) { 1441 dev_err(&i2c->dev, "Failed to enable LRCM: %d\n", 1442 ret); 1443 return ret; 1444 } 1445 } 1446 1447 /* Latch the update bits */ 1448 regmap_update_bits(wm8960->regmap, WM8960_LINVOL, 0x100, 0x100); 1449 regmap_update_bits(wm8960->regmap, WM8960_RINVOL, 0x100, 0x100); 1450 regmap_update_bits(wm8960->regmap, WM8960_LADC, 0x100, 0x100); 1451 regmap_update_bits(wm8960->regmap, WM8960_RADC, 0x100, 0x100); 1452 regmap_update_bits(wm8960->regmap, WM8960_LDAC, 0x100, 0x100); 1453 regmap_update_bits(wm8960->regmap, WM8960_RDAC, 0x100, 0x100); 1454 regmap_update_bits(wm8960->regmap, WM8960_LOUT1, 0x100, 0x100); 1455 regmap_update_bits(wm8960->regmap, WM8960_ROUT1, 0x100, 0x100); 1456 regmap_update_bits(wm8960->regmap, WM8960_LOUT2, 0x100, 0x100); 1457 regmap_update_bits(wm8960->regmap, WM8960_ROUT2, 0x100, 0x100); 1458 1459 /* ADCLRC pin configured as GPIO. */ 1460 regmap_update_bits(wm8960->regmap, WM8960_IFACE2, 1 << 6, 1461 wm8960->pdata.gpio_cfg[0] << 6); 1462 regmap_update_bits(wm8960->regmap, WM8960_ADDCTL4, 0xF << 4, 1463 wm8960->pdata.gpio_cfg[1] << 4); 1464 1465 /* Enable headphone jack detect */ 1466 regmap_update_bits(wm8960->regmap, WM8960_ADDCTL4, 3 << 2, 1467 wm8960->pdata.hp_cfg[0] << 2); 1468 regmap_update_bits(wm8960->regmap, WM8960_ADDCTL2, 3 << 5, 1469 wm8960->pdata.hp_cfg[1] << 5); 1470 regmap_update_bits(wm8960->regmap, WM8960_ADDCTL1, 3, 1471 wm8960->pdata.hp_cfg[2]); 1472 1473 i2c_set_clientdata(i2c, wm8960); 1474 1475 ret = devm_snd_soc_register_component(&i2c->dev, 1476 &soc_component_dev_wm8960, &wm8960_dai, 1); 1477 1478 return ret; 1479 } 1480 1481 static int wm8960_i2c_remove(struct i2c_client *client) 1482 { 1483 return 0; 1484 } 1485 1486 static const struct i2c_device_id wm8960_i2c_id[] = { 1487 { "wm8960", 0 }, 1488 { } 1489 }; 1490 MODULE_DEVICE_TABLE(i2c, wm8960_i2c_id); 1491 1492 static const struct of_device_id wm8960_of_match[] = { 1493 { .compatible = "wlf,wm8960", }, 1494 { } 1495 }; 1496 MODULE_DEVICE_TABLE(of, wm8960_of_match); 1497 1498 static struct i2c_driver wm8960_i2c_driver = { 1499 .driver = { 1500 .name = "wm8960", 1501 .of_match_table = wm8960_of_match, 1502 }, 1503 .probe = wm8960_i2c_probe, 1504 .remove = wm8960_i2c_remove, 1505 .id_table = wm8960_i2c_id, 1506 }; 1507 1508 module_i2c_driver(wm8960_i2c_driver); 1509 1510 MODULE_DESCRIPTION("ASoC WM8960 driver"); 1511 MODULE_AUTHOR("Liam Girdwood"); 1512 MODULE_LICENSE("GPL"); 1513