1 // SPDX-License-Identifier: GPL-2.0-only 2 // Copyright (c) 2015-2021, The Linux Foundation. All rights reserved. 3 4 #include <linux/module.h> 5 #include <linux/init.h> 6 #include <linux/slab.h> 7 #include <linux/device.h> 8 #include <linux/pm_runtime.h> 9 #include <linux/printk.h> 10 #include <linux/delay.h> 11 #include <linux/kernel.h> 12 #include <sound/soc.h> 13 #include <sound/jack.h> 14 #include "wcd-mbhc-v2.h" 15 16 #define HS_DETECT_PLUG_TIME_MS (3 * 1000) 17 #define MBHC_BUTTON_PRESS_THRESHOLD_MIN 250 18 #define GND_MIC_SWAP_THRESHOLD 4 19 #define WCD_FAKE_REMOVAL_MIN_PERIOD_MS 100 20 #define HPHL_CROSS_CONN_THRESHOLD 100 21 #define HS_VREF_MIN_VAL 1400 22 #define FAKE_REM_RETRY_ATTEMPTS 3 23 #define WCD_MBHC_ADC_HS_THRESHOLD_MV 1700 24 #define WCD_MBHC_ADC_HPH_THRESHOLD_MV 75 25 #define WCD_MBHC_ADC_MICBIAS_MV 1800 26 #define WCD_MBHC_FAKE_INS_RETRY 4 27 28 #define WCD_MBHC_JACK_MASK (SND_JACK_HEADSET | SND_JACK_LINEOUT | \ 29 SND_JACK_MECHANICAL) 30 31 #define WCD_MBHC_JACK_BUTTON_MASK (SND_JACK_BTN_0 | SND_JACK_BTN_1 | \ 32 SND_JACK_BTN_2 | SND_JACK_BTN_3 | \ 33 SND_JACK_BTN_4 | SND_JACK_BTN_5) 34 35 enum wcd_mbhc_adc_mux_ctl { 36 MUX_CTL_AUTO = 0, 37 MUX_CTL_IN2P, 38 MUX_CTL_IN3P, 39 MUX_CTL_IN4P, 40 MUX_CTL_HPH_L, 41 MUX_CTL_HPH_R, 42 MUX_CTL_NONE, 43 }; 44 45 struct wcd_mbhc { 46 struct device *dev; 47 struct snd_soc_component *component; 48 struct snd_soc_jack *jack; 49 struct wcd_mbhc_config *cfg; 50 const struct wcd_mbhc_cb *mbhc_cb; 51 const struct wcd_mbhc_intr *intr_ids; 52 struct wcd_mbhc_field *fields; 53 /* Delayed work to report long button press */ 54 struct delayed_work mbhc_btn_dwork; 55 /* Work to correct accessory type */ 56 struct work_struct correct_plug_swch; 57 struct mutex lock; 58 int buttons_pressed; 59 u32 hph_status; /* track headhpone status */ 60 u8 current_plug; 61 bool is_btn_press; 62 bool in_swch_irq_handler; 63 bool hs_detect_work_stop; 64 bool is_hs_recording; 65 bool extn_cable_hph_rem; 66 bool force_linein; 67 bool impedance_detect; 68 unsigned long event_state; 69 unsigned long jiffies_atreport; 70 /* impedance of hphl and hphr */ 71 uint32_t zl, zr; 72 /* Holds type of Headset - Mono/Stereo */ 73 enum wcd_mbhc_hph_type hph_type; 74 /* Holds mbhc detection method - ADC/Legacy */ 75 int mbhc_detection_logic; 76 }; 77 78 static inline int wcd_mbhc_write_field(const struct wcd_mbhc *mbhc, 79 int field, int val) 80 { 81 if (!mbhc->fields[field].reg) 82 return 0; 83 84 return snd_soc_component_write_field(mbhc->component, 85 mbhc->fields[field].reg, 86 mbhc->fields[field].mask, val); 87 } 88 89 static inline int wcd_mbhc_read_field(const struct wcd_mbhc *mbhc, int field) 90 { 91 if (!mbhc->fields[field].reg) 92 return 0; 93 94 return snd_soc_component_read_field(mbhc->component, 95 mbhc->fields[field].reg, 96 mbhc->fields[field].mask); 97 } 98 99 static void wcd_program_hs_vref(struct wcd_mbhc *mbhc) 100 { 101 u32 reg_val = ((mbhc->cfg->v_hs_max - HS_VREF_MIN_VAL) / 100); 102 103 wcd_mbhc_write_field(mbhc, WCD_MBHC_HS_VREF, reg_val); 104 } 105 106 static void wcd_program_btn_threshold(const struct wcd_mbhc *mbhc, bool micbias) 107 { 108 struct snd_soc_component *component = mbhc->component; 109 110 mbhc->mbhc_cb->set_btn_thr(component, mbhc->cfg->btn_low, 111 mbhc->cfg->btn_high, 112 mbhc->cfg->num_btn, micbias); 113 } 114 115 static void wcd_mbhc_curr_micbias_control(const struct wcd_mbhc *mbhc, 116 const enum wcd_mbhc_cs_mb_en_flag cs_mb_en) 117 { 118 119 /* 120 * Some codecs handle micbias/pullup enablement in codec 121 * drivers itself and micbias is not needed for regular 122 * plug type detection. So if micbias_control callback function 123 * is defined, just return. 124 */ 125 if (mbhc->mbhc_cb->mbhc_micbias_control) 126 return; 127 128 switch (cs_mb_en) { 129 case WCD_MBHC_EN_CS: 130 wcd_mbhc_write_field(mbhc, WCD_MBHC_MICB_CTRL, 0); 131 wcd_mbhc_write_field(mbhc, WCD_MBHC_BTN_ISRC_CTL, 3); 132 /* Program Button threshold registers as per CS */ 133 wcd_program_btn_threshold(mbhc, false); 134 break; 135 case WCD_MBHC_EN_MB: 136 wcd_mbhc_write_field(mbhc, WCD_MBHC_BTN_ISRC_CTL, 0); 137 wcd_mbhc_write_field(mbhc, WCD_MBHC_FSM_EN, 1); 138 /* Disable PULL_UP_EN & enable MICBIAS */ 139 wcd_mbhc_write_field(mbhc, WCD_MBHC_MICB_CTRL, 2); 140 /* Program Button threshold registers as per MICBIAS */ 141 wcd_program_btn_threshold(mbhc, true); 142 break; 143 case WCD_MBHC_EN_PULLUP: 144 wcd_mbhc_write_field(mbhc, WCD_MBHC_BTN_ISRC_CTL, 3); 145 wcd_mbhc_write_field(mbhc, WCD_MBHC_FSM_EN, 1); 146 wcd_mbhc_write_field(mbhc, WCD_MBHC_MICB_CTRL, 1); 147 /* Program Button threshold registers as per MICBIAS */ 148 wcd_program_btn_threshold(mbhc, true); 149 break; 150 case WCD_MBHC_EN_NONE: 151 wcd_mbhc_write_field(mbhc, WCD_MBHC_BTN_ISRC_CTL, 0); 152 wcd_mbhc_write_field(mbhc, WCD_MBHC_FSM_EN, 1); 153 wcd_mbhc_write_field(mbhc, WCD_MBHC_MICB_CTRL, 0); 154 break; 155 default: 156 dev_err(mbhc->dev, "%s: Invalid parameter", __func__); 157 break; 158 } 159 } 160 161 int wcd_mbhc_event_notify(struct wcd_mbhc *mbhc, unsigned long event) 162 { 163 164 struct snd_soc_component *component; 165 bool micbias2 = false; 166 167 if (!mbhc) 168 return 0; 169 170 component = mbhc->component; 171 172 if (mbhc->mbhc_cb->micbias_enable_status) 173 micbias2 = mbhc->mbhc_cb->micbias_enable_status(component, MIC_BIAS_2); 174 175 switch (event) { 176 /* MICBIAS usage change */ 177 case WCD_EVENT_POST_DAPM_MICBIAS_2_ON: 178 mbhc->is_hs_recording = true; 179 break; 180 case WCD_EVENT_POST_MICBIAS_2_ON: 181 /* Disable current source if micbias2 enabled */ 182 if (mbhc->mbhc_cb->mbhc_micbias_control) { 183 if (wcd_mbhc_read_field(mbhc, WCD_MBHC_FSM_EN)) 184 wcd_mbhc_write_field(mbhc, WCD_MBHC_BTN_ISRC_CTL, 0); 185 } else { 186 mbhc->is_hs_recording = true; 187 wcd_mbhc_curr_micbias_control(mbhc, WCD_MBHC_EN_MB); 188 } 189 break; 190 case WCD_EVENT_PRE_MICBIAS_2_OFF: 191 /* 192 * Before MICBIAS_2 is turned off, if FSM is enabled, 193 * make sure current source is enabled so as to detect 194 * button press/release events 195 */ 196 if (mbhc->mbhc_cb->mbhc_micbias_control/* && !mbhc->micbias_enable*/) { 197 if (wcd_mbhc_read_field(mbhc, WCD_MBHC_FSM_EN)) 198 wcd_mbhc_write_field(mbhc, WCD_MBHC_BTN_ISRC_CTL, 3); 199 } 200 break; 201 /* MICBIAS usage change */ 202 case WCD_EVENT_POST_DAPM_MICBIAS_2_OFF: 203 mbhc->is_hs_recording = false; 204 break; 205 case WCD_EVENT_POST_MICBIAS_2_OFF: 206 if (!mbhc->mbhc_cb->mbhc_micbias_control) 207 mbhc->is_hs_recording = false; 208 209 /* Enable PULL UP if PA's are enabled */ 210 if ((test_bit(WCD_MBHC_EVENT_PA_HPHL, &mbhc->event_state)) || 211 (test_bit(WCD_MBHC_EVENT_PA_HPHR, &mbhc->event_state))) 212 /* enable pullup and cs, disable mb */ 213 wcd_mbhc_curr_micbias_control(mbhc, WCD_MBHC_EN_PULLUP); 214 else 215 /* enable current source and disable mb, pullup*/ 216 wcd_mbhc_curr_micbias_control(mbhc, WCD_MBHC_EN_CS); 217 218 break; 219 case WCD_EVENT_POST_HPHL_PA_OFF: 220 clear_bit(WCD_MBHC_EVENT_PA_HPHL, &mbhc->event_state); 221 222 /* check if micbias is enabled */ 223 if (micbias2) 224 /* Disable cs, pullup & enable micbias */ 225 wcd_mbhc_curr_micbias_control(mbhc, WCD_MBHC_EN_MB); 226 else 227 /* Disable micbias, pullup & enable cs */ 228 wcd_mbhc_curr_micbias_control(mbhc, WCD_MBHC_EN_CS); 229 break; 230 case WCD_EVENT_POST_HPHR_PA_OFF: 231 clear_bit(WCD_MBHC_EVENT_PA_HPHR, &mbhc->event_state); 232 /* check if micbias is enabled */ 233 if (micbias2) 234 /* Disable cs, pullup & enable micbias */ 235 wcd_mbhc_curr_micbias_control(mbhc, WCD_MBHC_EN_MB); 236 else 237 /* Disable micbias, pullup & enable cs */ 238 wcd_mbhc_curr_micbias_control(mbhc, WCD_MBHC_EN_CS); 239 break; 240 case WCD_EVENT_PRE_HPHL_PA_ON: 241 set_bit(WCD_MBHC_EVENT_PA_HPHL, &mbhc->event_state); 242 /* check if micbias is enabled */ 243 if (micbias2) 244 /* Disable cs, pullup & enable micbias */ 245 wcd_mbhc_curr_micbias_control(mbhc, WCD_MBHC_EN_MB); 246 else 247 /* Disable micbias, enable pullup & cs */ 248 wcd_mbhc_curr_micbias_control(mbhc, WCD_MBHC_EN_PULLUP); 249 break; 250 case WCD_EVENT_PRE_HPHR_PA_ON: 251 set_bit(WCD_MBHC_EVENT_PA_HPHR, &mbhc->event_state); 252 /* check if micbias is enabled */ 253 if (micbias2) 254 /* Disable cs, pullup & enable micbias */ 255 wcd_mbhc_curr_micbias_control(mbhc, WCD_MBHC_EN_MB); 256 else 257 /* Disable micbias, enable pullup & cs */ 258 wcd_mbhc_curr_micbias_control(mbhc, WCD_MBHC_EN_PULLUP); 259 break; 260 default: 261 break; 262 } 263 return 0; 264 } 265 EXPORT_SYMBOL_GPL(wcd_mbhc_event_notify); 266 267 static int wcd_cancel_btn_work(struct wcd_mbhc *mbhc) 268 { 269 return cancel_delayed_work_sync(&mbhc->mbhc_btn_dwork); 270 } 271 272 static void wcd_micbias_disable(struct wcd_mbhc *mbhc) 273 { 274 struct snd_soc_component *component = mbhc->component; 275 276 if (mbhc->mbhc_cb->mbhc_micbias_control) 277 mbhc->mbhc_cb->mbhc_micbias_control(component, MIC_BIAS_2, MICB_DISABLE); 278 279 if (mbhc->mbhc_cb->mbhc_micb_ctrl_thr_mic) 280 mbhc->mbhc_cb->mbhc_micb_ctrl_thr_mic(component, MIC_BIAS_2, false); 281 282 if (mbhc->mbhc_cb->set_micbias_value) { 283 mbhc->mbhc_cb->set_micbias_value(component); 284 wcd_mbhc_write_field(mbhc, WCD_MBHC_MICB_CTRL, 0); 285 } 286 } 287 288 static void wcd_mbhc_report_plug_removal(struct wcd_mbhc *mbhc, 289 enum snd_jack_types jack_type) 290 { 291 mbhc->hph_status &= ~jack_type; 292 /* 293 * cancel possibly scheduled btn work and 294 * report release if we reported button press 295 */ 296 if (!wcd_cancel_btn_work(mbhc) && mbhc->buttons_pressed) { 297 snd_soc_jack_report(mbhc->jack, 0, mbhc->buttons_pressed); 298 mbhc->buttons_pressed &= ~WCD_MBHC_JACK_BUTTON_MASK; 299 } 300 301 wcd_micbias_disable(mbhc); 302 mbhc->hph_type = WCD_MBHC_HPH_NONE; 303 mbhc->zl = mbhc->zr = 0; 304 snd_soc_jack_report(mbhc->jack, mbhc->hph_status, WCD_MBHC_JACK_MASK); 305 mbhc->current_plug = MBHC_PLUG_TYPE_NONE; 306 mbhc->force_linein = false; 307 } 308 309 static void wcd_mbhc_compute_impedance(struct wcd_mbhc *mbhc) 310 { 311 312 if (!mbhc->impedance_detect) 313 return; 314 315 if (mbhc->cfg->linein_th != 0) { 316 u8 fsm_en = wcd_mbhc_read_field(mbhc, WCD_MBHC_FSM_EN); 317 /* Set MUX_CTL to AUTO for Z-det */ 318 319 wcd_mbhc_write_field(mbhc, WCD_MBHC_FSM_EN, 0); 320 wcd_mbhc_write_field(mbhc, WCD_MBHC_MUX_CTL, MUX_CTL_AUTO); 321 wcd_mbhc_write_field(mbhc, WCD_MBHC_FSM_EN, 1); 322 mbhc->mbhc_cb->compute_impedance(mbhc->component, &mbhc->zl, &mbhc->zr); 323 wcd_mbhc_write_field(mbhc, WCD_MBHC_FSM_EN, fsm_en); 324 } 325 } 326 327 static void wcd_mbhc_report_plug_insertion(struct wcd_mbhc *mbhc, 328 enum snd_jack_types jack_type) 329 { 330 bool is_pa_on; 331 /* 332 * Report removal of current jack type. 333 * Headphone to headset shouldn't report headphone 334 * removal. 335 */ 336 if (mbhc->current_plug == MBHC_PLUG_TYPE_HEADSET && 337 jack_type == SND_JACK_HEADPHONE) 338 mbhc->hph_status &= ~SND_JACK_HEADSET; 339 340 /* Report insertion */ 341 switch (jack_type) { 342 case SND_JACK_HEADPHONE: 343 mbhc->current_plug = MBHC_PLUG_TYPE_HEADPHONE; 344 break; 345 case SND_JACK_HEADSET: 346 mbhc->current_plug = MBHC_PLUG_TYPE_HEADSET; 347 mbhc->jiffies_atreport = jiffies; 348 break; 349 case SND_JACK_LINEOUT: 350 mbhc->current_plug = MBHC_PLUG_TYPE_HIGH_HPH; 351 break; 352 default: 353 break; 354 } 355 356 357 is_pa_on = wcd_mbhc_read_field(mbhc, WCD_MBHC_HPH_PA_EN); 358 359 if (!is_pa_on) { 360 wcd_mbhc_compute_impedance(mbhc); 361 if ((mbhc->zl > mbhc->cfg->linein_th) && 362 (mbhc->zr > mbhc->cfg->linein_th) && 363 (jack_type == SND_JACK_HEADPHONE)) { 364 jack_type = SND_JACK_LINEOUT; 365 mbhc->force_linein = true; 366 mbhc->current_plug = MBHC_PLUG_TYPE_HIGH_HPH; 367 if (mbhc->hph_status) { 368 mbhc->hph_status &= ~(SND_JACK_HEADSET | 369 SND_JACK_LINEOUT); 370 snd_soc_jack_report(mbhc->jack, mbhc->hph_status, 371 WCD_MBHC_JACK_MASK); 372 } 373 } 374 } 375 376 /* Do not calculate impedance again for lineout 377 * as during playback pa is on and impedance values 378 * will not be correct resulting in lineout detected 379 * as headphone. 380 */ 381 if (is_pa_on && mbhc->force_linein) { 382 jack_type = SND_JACK_LINEOUT; 383 mbhc->current_plug = MBHC_PLUG_TYPE_HIGH_HPH; 384 if (mbhc->hph_status) { 385 mbhc->hph_status &= ~(SND_JACK_HEADSET | 386 SND_JACK_LINEOUT); 387 snd_soc_jack_report(mbhc->jack, mbhc->hph_status, 388 WCD_MBHC_JACK_MASK); 389 } 390 } 391 392 mbhc->hph_status |= jack_type; 393 394 if (jack_type == SND_JACK_HEADPHONE && mbhc->mbhc_cb->mbhc_micb_ramp_control) 395 mbhc->mbhc_cb->mbhc_micb_ramp_control(mbhc->component, false); 396 397 snd_soc_jack_report(mbhc->jack, (mbhc->hph_status | SND_JACK_MECHANICAL), 398 WCD_MBHC_JACK_MASK); 399 } 400 401 static void wcd_mbhc_report_plug(struct wcd_mbhc *mbhc, int insertion, 402 enum snd_jack_types jack_type) 403 { 404 405 WARN_ON(!mutex_is_locked(&mbhc->lock)); 406 407 if (!insertion) /* Report removal */ 408 wcd_mbhc_report_plug_removal(mbhc, jack_type); 409 else 410 wcd_mbhc_report_plug_insertion(mbhc, jack_type); 411 412 } 413 414 static void wcd_cancel_hs_detect_plug(struct wcd_mbhc *mbhc, 415 struct work_struct *work) 416 { 417 mbhc->hs_detect_work_stop = true; 418 mutex_unlock(&mbhc->lock); 419 cancel_work_sync(work); 420 mutex_lock(&mbhc->lock); 421 } 422 423 static void wcd_mbhc_cancel_pending_work(struct wcd_mbhc *mbhc) 424 { 425 /* cancel pending button press */ 426 wcd_cancel_btn_work(mbhc); 427 /* cancel correct work function */ 428 wcd_cancel_hs_detect_plug(mbhc, &mbhc->correct_plug_swch); 429 } 430 431 static void wcd_mbhc_elec_hs_report_unplug(struct wcd_mbhc *mbhc) 432 { 433 wcd_mbhc_cancel_pending_work(mbhc); 434 /* Report extension cable */ 435 wcd_mbhc_report_plug(mbhc, 1, SND_JACK_LINEOUT); 436 /* 437 * Disable HPHL trigger and MIC Schmitt triggers. 438 * Setup for insertion detection. 439 */ 440 disable_irq_nosync(mbhc->intr_ids->mbhc_hs_rem_intr); 441 wcd_mbhc_curr_micbias_control(mbhc, WCD_MBHC_EN_NONE); 442 /* Disable HW FSM */ 443 wcd_mbhc_write_field(mbhc, WCD_MBHC_FSM_EN, 0); 444 wcd_mbhc_write_field(mbhc, WCD_MBHC_ELECT_SCHMT_ISRC, 3); 445 446 /* Set the detection type appropriately */ 447 wcd_mbhc_write_field(mbhc, WCD_MBHC_ELECT_DETECTION_TYPE, 1); 448 enable_irq(mbhc->intr_ids->mbhc_hs_ins_intr); 449 } 450 451 static void wcd_mbhc_find_plug_and_report(struct wcd_mbhc *mbhc, 452 enum wcd_mbhc_plug_type plug_type) 453 { 454 if (mbhc->current_plug == plug_type) 455 return; 456 457 mutex_lock(&mbhc->lock); 458 459 switch (plug_type) { 460 case MBHC_PLUG_TYPE_HEADPHONE: 461 wcd_mbhc_report_plug(mbhc, 1, SND_JACK_HEADPHONE); 462 break; 463 case MBHC_PLUG_TYPE_HEADSET: 464 wcd_mbhc_report_plug(mbhc, 1, SND_JACK_HEADSET); 465 break; 466 case MBHC_PLUG_TYPE_HIGH_HPH: 467 wcd_mbhc_report_plug(mbhc, 1, SND_JACK_LINEOUT); 468 break; 469 case MBHC_PLUG_TYPE_GND_MIC_SWAP: 470 if (mbhc->current_plug == MBHC_PLUG_TYPE_HEADPHONE) 471 wcd_mbhc_report_plug(mbhc, 0, SND_JACK_HEADPHONE); 472 if (mbhc->current_plug == MBHC_PLUG_TYPE_HEADSET) 473 wcd_mbhc_report_plug(mbhc, 0, SND_JACK_HEADSET); 474 break; 475 default: 476 WARN(1, "Unexpected current plug_type %d, plug_type %d\n", 477 mbhc->current_plug, plug_type); 478 break; 479 } 480 mutex_unlock(&mbhc->lock); 481 } 482 483 static void wcd_schedule_hs_detect_plug(struct wcd_mbhc *mbhc, 484 struct work_struct *work) 485 { 486 WARN_ON(!mutex_is_locked(&mbhc->lock)); 487 mbhc->hs_detect_work_stop = false; 488 schedule_work(work); 489 } 490 491 static void wcd_mbhc_adc_detect_plug_type(struct wcd_mbhc *mbhc) 492 { 493 struct snd_soc_component *component = mbhc->component; 494 495 WARN_ON(!mutex_is_locked(&mbhc->lock)); 496 497 if (mbhc->mbhc_cb->hph_pull_down_ctrl) 498 mbhc->mbhc_cb->hph_pull_down_ctrl(component, false); 499 500 wcd_mbhc_write_field(mbhc, WCD_MBHC_DETECTION_DONE, 0); 501 502 if (mbhc->mbhc_cb->mbhc_micbias_control) { 503 mbhc->mbhc_cb->mbhc_micbias_control(component, MIC_BIAS_2, 504 MICB_ENABLE); 505 wcd_schedule_hs_detect_plug(mbhc, &mbhc->correct_plug_swch); 506 } 507 } 508 509 static irqreturn_t wcd_mbhc_mech_plug_detect_irq(int irq, void *data) 510 { 511 struct snd_soc_component *component; 512 enum snd_jack_types jack_type; 513 struct wcd_mbhc *mbhc = data; 514 bool detection_type; 515 516 component = mbhc->component; 517 mutex_lock(&mbhc->lock); 518 519 mbhc->in_swch_irq_handler = true; 520 521 wcd_mbhc_cancel_pending_work(mbhc); 522 523 detection_type = wcd_mbhc_read_field(mbhc, WCD_MBHC_MECH_DETECTION_TYPE); 524 525 /* Set the detection type appropriately */ 526 wcd_mbhc_write_field(mbhc, WCD_MBHC_MECH_DETECTION_TYPE, !detection_type); 527 528 /* Enable micbias ramp */ 529 if (mbhc->mbhc_cb->mbhc_micb_ramp_control) 530 mbhc->mbhc_cb->mbhc_micb_ramp_control(component, true); 531 532 if (detection_type) { 533 if (mbhc->current_plug != MBHC_PLUG_TYPE_NONE) 534 goto exit; 535 /* Make sure MASTER_BIAS_CTL is enabled */ 536 mbhc->mbhc_cb->mbhc_bias(component, true); 537 mbhc->is_btn_press = false; 538 wcd_mbhc_adc_detect_plug_type(mbhc); 539 } else { 540 /* Disable HW FSM */ 541 wcd_mbhc_write_field(mbhc, WCD_MBHC_FSM_EN, 0); 542 wcd_mbhc_write_field(mbhc, WCD_MBHC_BTN_ISRC_CTL, 0); 543 mbhc->extn_cable_hph_rem = false; 544 545 if (mbhc->current_plug == MBHC_PLUG_TYPE_NONE) 546 goto exit; 547 548 mbhc->is_btn_press = false; 549 switch (mbhc->current_plug) { 550 case MBHC_PLUG_TYPE_HEADPHONE: 551 jack_type = SND_JACK_HEADPHONE; 552 break; 553 case MBHC_PLUG_TYPE_HEADSET: 554 jack_type = SND_JACK_HEADSET; 555 break; 556 case MBHC_PLUG_TYPE_HIGH_HPH: 557 if (mbhc->mbhc_detection_logic == WCD_DETECTION_ADC) 558 wcd_mbhc_write_field(mbhc, WCD_MBHC_ELECT_ISRC_EN, 0); 559 jack_type = SND_JACK_LINEOUT; 560 break; 561 case MBHC_PLUG_TYPE_GND_MIC_SWAP: 562 dev_err(mbhc->dev, "Ground and Mic Swapped on plug\n"); 563 goto exit; 564 default: 565 dev_err(mbhc->dev, "Invalid current plug: %d\n", 566 mbhc->current_plug); 567 goto exit; 568 } 569 disable_irq_nosync(mbhc->intr_ids->mbhc_hs_rem_intr); 570 disable_irq_nosync(mbhc->intr_ids->mbhc_hs_ins_intr); 571 wcd_mbhc_write_field(mbhc, WCD_MBHC_ELECT_DETECTION_TYPE, 1); 572 wcd_mbhc_write_field(mbhc, WCD_MBHC_ELECT_SCHMT_ISRC, 0); 573 wcd_mbhc_report_plug(mbhc, 0, jack_type); 574 } 575 576 exit: 577 mbhc->in_swch_irq_handler = false; 578 mutex_unlock(&mbhc->lock); 579 return IRQ_HANDLED; 580 } 581 582 static int wcd_mbhc_get_button_mask(struct wcd_mbhc *mbhc) 583 { 584 int mask = 0; 585 int btn; 586 587 btn = wcd_mbhc_read_field(mbhc, WCD_MBHC_BTN_RESULT); 588 589 switch (btn) { 590 case 0: 591 mask = SND_JACK_BTN_0; 592 break; 593 case 1: 594 mask = SND_JACK_BTN_1; 595 break; 596 case 2: 597 mask = SND_JACK_BTN_2; 598 break; 599 case 3: 600 mask = SND_JACK_BTN_3; 601 break; 602 case 4: 603 mask = SND_JACK_BTN_4; 604 break; 605 case 5: 606 mask = SND_JACK_BTN_5; 607 break; 608 default: 609 break; 610 } 611 612 return mask; 613 } 614 615 static void wcd_btn_long_press_fn(struct work_struct *work) 616 { 617 struct delayed_work *dwork = to_delayed_work(work); 618 struct wcd_mbhc *mbhc = container_of(dwork, struct wcd_mbhc, mbhc_btn_dwork); 619 620 if (mbhc->current_plug == MBHC_PLUG_TYPE_HEADSET) 621 snd_soc_jack_report(mbhc->jack, mbhc->buttons_pressed, 622 mbhc->buttons_pressed); 623 } 624 625 static irqreturn_t wcd_mbhc_btn_press_handler(int irq, void *data) 626 { 627 struct wcd_mbhc *mbhc = data; 628 int mask; 629 unsigned long msec_val; 630 631 mutex_lock(&mbhc->lock); 632 wcd_cancel_btn_work(mbhc); 633 mbhc->is_btn_press = true; 634 msec_val = jiffies_to_msecs(jiffies - mbhc->jiffies_atreport); 635 636 /* Too short, ignore button press */ 637 if (msec_val < MBHC_BUTTON_PRESS_THRESHOLD_MIN) 638 goto done; 639 640 /* If switch interrupt already kicked in, ignore button press */ 641 if (mbhc->in_swch_irq_handler) 642 goto done; 643 644 /* Plug isn't headset, ignore button press */ 645 if (mbhc->current_plug != MBHC_PLUG_TYPE_HEADSET) 646 goto done; 647 648 mask = wcd_mbhc_get_button_mask(mbhc); 649 mbhc->buttons_pressed |= mask; 650 if (schedule_delayed_work(&mbhc->mbhc_btn_dwork, msecs_to_jiffies(400)) == 0) 651 WARN(1, "Button pressed twice without release event\n"); 652 done: 653 mutex_unlock(&mbhc->lock); 654 return IRQ_HANDLED; 655 } 656 657 static irqreturn_t wcd_mbhc_btn_release_handler(int irq, void *data) 658 { 659 struct wcd_mbhc *mbhc = data; 660 int ret; 661 662 mutex_lock(&mbhc->lock); 663 if (mbhc->is_btn_press) 664 mbhc->is_btn_press = false; 665 else /* fake btn press */ 666 goto exit; 667 668 if (!(mbhc->buttons_pressed & WCD_MBHC_JACK_BUTTON_MASK)) 669 goto exit; 670 671 ret = wcd_cancel_btn_work(mbhc); 672 if (ret == 0) { /* Reporting long button release event */ 673 snd_soc_jack_report(mbhc->jack, 0, mbhc->buttons_pressed); 674 } else { 675 if (!mbhc->in_swch_irq_handler) { 676 /* Reporting btn press n Release */ 677 snd_soc_jack_report(mbhc->jack, mbhc->buttons_pressed, 678 mbhc->buttons_pressed); 679 snd_soc_jack_report(mbhc->jack, 0, mbhc->buttons_pressed); 680 } 681 } 682 mbhc->buttons_pressed &= ~WCD_MBHC_JACK_BUTTON_MASK; 683 exit: 684 mutex_unlock(&mbhc->lock); 685 686 return IRQ_HANDLED; 687 } 688 689 static irqreturn_t wcd_mbhc_hph_ocp_irq(struct wcd_mbhc *mbhc, bool hphr) 690 { 691 692 /* TODO Find a better way to report this to Userspace */ 693 dev_err(mbhc->dev, "MBHC Over Current on %s detected\n", 694 hphr ? "HPHR" : "HPHL"); 695 696 wcd_mbhc_write_field(mbhc, WCD_MBHC_OCP_FSM_EN, 0); 697 wcd_mbhc_write_field(mbhc, WCD_MBHC_OCP_FSM_EN, 1); 698 699 return IRQ_HANDLED; 700 } 701 702 static irqreturn_t wcd_mbhc_hphl_ocp_irq(int irq, void *data) 703 { 704 return wcd_mbhc_hph_ocp_irq(data, false); 705 } 706 707 static irqreturn_t wcd_mbhc_hphr_ocp_irq(int irq, void *data) 708 { 709 return wcd_mbhc_hph_ocp_irq(data, true); 710 } 711 712 static int wcd_mbhc_initialise(struct wcd_mbhc *mbhc) 713 { 714 struct snd_soc_component *component = mbhc->component; 715 int ret; 716 717 ret = pm_runtime_get_sync(component->dev); 718 if (ret < 0 && ret != -EACCES) { 719 dev_err_ratelimited(component->dev, 720 "pm_runtime_get_sync failed in %s, ret %d\n", 721 __func__, ret); 722 pm_runtime_put_noidle(component->dev); 723 return ret; 724 } 725 726 mutex_lock(&mbhc->lock); 727 728 /* enable HS detection */ 729 if (mbhc->mbhc_cb->hph_pull_up_control_v2) 730 mbhc->mbhc_cb->hph_pull_up_control_v2(component, 731 HS_PULLUP_I_DEFAULT); 732 else if (mbhc->mbhc_cb->hph_pull_up_control) 733 mbhc->mbhc_cb->hph_pull_up_control(component, I_DEFAULT); 734 else 735 wcd_mbhc_write_field(mbhc, WCD_MBHC_HS_L_DET_PULL_UP_CTRL, 3); 736 737 wcd_mbhc_write_field(mbhc, WCD_MBHC_HPHL_PLUG_TYPE, mbhc->cfg->hphl_swh); 738 wcd_mbhc_write_field(mbhc, WCD_MBHC_GND_PLUG_TYPE, mbhc->cfg->gnd_swh); 739 wcd_mbhc_write_field(mbhc, WCD_MBHC_SW_HPH_LP_100K_TO_GND, 1); 740 if (mbhc->cfg->gnd_det_en && mbhc->mbhc_cb->mbhc_gnd_det_ctrl) 741 mbhc->mbhc_cb->mbhc_gnd_det_ctrl(component, true); 742 wcd_mbhc_write_field(mbhc, WCD_MBHC_HS_L_DET_PULL_UP_COMP_CTRL, 1); 743 744 wcd_mbhc_write_field(mbhc, WCD_MBHC_L_DET_EN, 1); 745 746 /* Insertion debounce set to 96ms */ 747 wcd_mbhc_write_field(mbhc, WCD_MBHC_INSREM_DBNC, 6); 748 749 /* Button Debounce set to 16ms */ 750 wcd_mbhc_write_field(mbhc, WCD_MBHC_BTN_DBNC, 2); 751 752 /* enable bias */ 753 mbhc->mbhc_cb->mbhc_bias(component, true); 754 /* enable MBHC clock */ 755 if (mbhc->mbhc_cb->clk_setup) 756 mbhc->mbhc_cb->clk_setup(component, true); 757 758 /* program HS_VREF value */ 759 wcd_program_hs_vref(mbhc); 760 761 wcd_program_btn_threshold(mbhc, false); 762 763 mutex_unlock(&mbhc->lock); 764 765 pm_runtime_mark_last_busy(component->dev); 766 pm_runtime_put_autosuspend(component->dev); 767 768 return 0; 769 } 770 771 static int wcd_mbhc_get_micbias(struct wcd_mbhc *mbhc) 772 { 773 int micbias = 0; 774 775 if (mbhc->mbhc_cb->get_micbias_val) { 776 mbhc->mbhc_cb->get_micbias_val(mbhc->component, &micbias); 777 } else { 778 u8 vout_ctl = 0; 779 /* Read MBHC Micbias (Mic Bias2) voltage */ 780 vout_ctl = wcd_mbhc_read_field(mbhc, WCD_MBHC_MICB2_VOUT); 781 /* Formula for getting micbias from vout 782 * micbias = 1.0V + VOUT_CTL * 50mV 783 */ 784 micbias = 1000 + (vout_ctl * 50); 785 } 786 return micbias; 787 } 788 789 static int wcd_get_voltage_from_adc(u8 val, int micbias) 790 { 791 /* Formula for calculating voltage from ADC 792 * Voltage = ADC_RESULT*12.5mV*V_MICBIAS/1.8 793 */ 794 return ((val * 125 * micbias)/(WCD_MBHC_ADC_MICBIAS_MV * 10)); 795 } 796 797 static int wcd_measure_adc_continuous(struct wcd_mbhc *mbhc) 798 { 799 u8 adc_result; 800 int output_mv; 801 int retry = 3; 802 u8 adc_en; 803 804 /* Pre-requisites for ADC continuous measurement */ 805 /* Read legacy electircal detection and disable */ 806 wcd_mbhc_write_field(mbhc, WCD_MBHC_ELECT_SCHMT_ISRC, 0x00); 807 /* Set ADC to continuous measurement */ 808 wcd_mbhc_write_field(mbhc, WCD_MBHC_ADC_MODE, 1); 809 /* Read ADC Enable bit to restore after adc measurement */ 810 adc_en = wcd_mbhc_read_field(mbhc, WCD_MBHC_ADC_EN); 811 /* Disable ADC_ENABLE bit */ 812 wcd_mbhc_write_field(mbhc, WCD_MBHC_ADC_EN, 0); 813 /* Disable MBHC FSM */ 814 wcd_mbhc_write_field(mbhc, WCD_MBHC_FSM_EN, 0); 815 /* Set the MUX selection to IN2P */ 816 wcd_mbhc_write_field(mbhc, WCD_MBHC_MUX_CTL, MUX_CTL_IN2P); 817 /* Enable MBHC FSM */ 818 wcd_mbhc_write_field(mbhc, WCD_MBHC_FSM_EN, 1); 819 /* Enable ADC_ENABLE bit */ 820 wcd_mbhc_write_field(mbhc, WCD_MBHC_ADC_EN, 1); 821 822 while (retry--) { 823 /* wait for 3 msec before reading ADC result */ 824 usleep_range(3000, 3100); 825 adc_result = wcd_mbhc_read_field(mbhc, WCD_MBHC_ADC_RESULT); 826 } 827 828 /* Restore ADC Enable */ 829 wcd_mbhc_write_field(mbhc, WCD_MBHC_ADC_EN, adc_en); 830 /* Get voltage from ADC result */ 831 output_mv = wcd_get_voltage_from_adc(adc_result, wcd_mbhc_get_micbias(mbhc)); 832 833 return output_mv; 834 } 835 836 static int wcd_measure_adc_once(struct wcd_mbhc *mbhc, int mux_ctl) 837 { 838 struct device *dev = mbhc->dev; 839 u8 adc_timeout = 0; 840 u8 adc_complete = 0; 841 u8 adc_result; 842 int retry = 6; 843 int ret; 844 int output_mv = 0; 845 u8 adc_en; 846 847 wcd_mbhc_write_field(mbhc, WCD_MBHC_ADC_MODE, 0); 848 /* Read ADC Enable bit to restore after adc measurement */ 849 adc_en = wcd_mbhc_read_field(mbhc, WCD_MBHC_ADC_EN); 850 /* Trigger ADC one time measurement */ 851 wcd_mbhc_write_field(mbhc, WCD_MBHC_ADC_EN, 0); 852 wcd_mbhc_write_field(mbhc, WCD_MBHC_FSM_EN, 0); 853 /* Set the appropriate MUX selection */ 854 wcd_mbhc_write_field(mbhc, WCD_MBHC_MUX_CTL, mux_ctl); 855 wcd_mbhc_write_field(mbhc, WCD_MBHC_FSM_EN, 1); 856 wcd_mbhc_write_field(mbhc, WCD_MBHC_ADC_EN, 1); 857 858 while (retry--) { 859 /* wait for 600usec to get adc results */ 860 usleep_range(600, 610); 861 862 /* check for ADC Timeout */ 863 adc_timeout = wcd_mbhc_read_field(mbhc, WCD_MBHC_ADC_TIMEOUT); 864 if (adc_timeout) 865 continue; 866 867 /* Read ADC complete bit */ 868 adc_complete = wcd_mbhc_read_field(mbhc, WCD_MBHC_ADC_COMPLETE); 869 if (!adc_complete) 870 continue; 871 872 /* Read ADC result */ 873 adc_result = wcd_mbhc_read_field(mbhc, WCD_MBHC_ADC_RESULT); 874 875 /* Get voltage from ADC result */ 876 output_mv = wcd_get_voltage_from_adc(adc_result, 877 wcd_mbhc_get_micbias(mbhc)); 878 break; 879 } 880 881 /* Restore ADC Enable */ 882 wcd_mbhc_write_field(mbhc, WCD_MBHC_ADC_EN, adc_en); 883 884 if (retry <= 0) { 885 dev_err(dev, "%s: adc complete: %d, adc timeout: %d\n", 886 __func__, adc_complete, adc_timeout); 887 ret = -EINVAL; 888 } else { 889 ret = output_mv; 890 } 891 892 return ret; 893 } 894 895 /* To determine if cross connection occurred */ 896 static int wcd_check_cross_conn(struct wcd_mbhc *mbhc) 897 { 898 u8 adc_mode, elect_ctl, adc_en, fsm_en; 899 int hphl_adc_res, hphr_adc_res; 900 bool is_cross_conn = false; 901 902 /* If PA is enabled, dont check for cross-connection */ 903 if (wcd_mbhc_read_field(mbhc, WCD_MBHC_HPH_PA_EN)) 904 return -EINVAL; 905 906 /* Read legacy electircal detection and disable */ 907 elect_ctl = wcd_mbhc_read_field(mbhc, WCD_MBHC_ELECT_SCHMT_ISRC); 908 wcd_mbhc_write_field(mbhc, WCD_MBHC_ELECT_SCHMT_ISRC, 0); 909 910 /* Read and set ADC to single measurement */ 911 adc_mode = wcd_mbhc_read_field(mbhc, WCD_MBHC_ADC_MODE); 912 /* Read ADC Enable bit to restore after adc measurement */ 913 adc_en = wcd_mbhc_read_field(mbhc, WCD_MBHC_ADC_EN); 914 /* Read FSM status */ 915 fsm_en = wcd_mbhc_read_field(mbhc, WCD_MBHC_FSM_EN); 916 917 /* Get adc result for HPH L */ 918 hphl_adc_res = wcd_measure_adc_once(mbhc, MUX_CTL_HPH_L); 919 if (hphl_adc_res < 0) 920 return hphl_adc_res; 921 922 /* Get adc result for HPH R in mV */ 923 hphr_adc_res = wcd_measure_adc_once(mbhc, MUX_CTL_HPH_R); 924 if (hphr_adc_res < 0) 925 return hphr_adc_res; 926 927 if (hphl_adc_res > HPHL_CROSS_CONN_THRESHOLD || 928 hphr_adc_res > HPHL_CROSS_CONN_THRESHOLD) 929 is_cross_conn = true; 930 931 wcd_mbhc_write_field(mbhc, WCD_MBHC_FSM_EN, 0); 932 /* Set the MUX selection to Auto */ 933 wcd_mbhc_write_field(mbhc, WCD_MBHC_MUX_CTL, MUX_CTL_AUTO); 934 wcd_mbhc_write_field(mbhc, WCD_MBHC_FSM_EN, 1); 935 /* Restore ADC Enable */ 936 wcd_mbhc_write_field(mbhc, WCD_MBHC_ADC_EN, adc_en); 937 /* Restore ADC mode */ 938 wcd_mbhc_write_field(mbhc, WCD_MBHC_ADC_MODE, adc_mode); 939 /* Restore FSM state */ 940 wcd_mbhc_write_field(mbhc, WCD_MBHC_FSM_EN, fsm_en); 941 /* Restore electrical detection */ 942 wcd_mbhc_write_field(mbhc, WCD_MBHC_ELECT_SCHMT_ISRC, elect_ctl); 943 944 return is_cross_conn; 945 } 946 947 static int wcd_mbhc_adc_get_hs_thres(struct wcd_mbhc *mbhc) 948 { 949 int hs_threshold, micbias_mv; 950 951 micbias_mv = wcd_mbhc_get_micbias(mbhc); 952 if (mbhc->cfg->hs_thr) { 953 if (mbhc->cfg->micb_mv == micbias_mv) 954 hs_threshold = mbhc->cfg->hs_thr; 955 else 956 hs_threshold = (mbhc->cfg->hs_thr * 957 micbias_mv) / mbhc->cfg->micb_mv; 958 } else { 959 hs_threshold = ((WCD_MBHC_ADC_HS_THRESHOLD_MV * 960 micbias_mv) / WCD_MBHC_ADC_MICBIAS_MV); 961 } 962 return hs_threshold; 963 } 964 965 static int wcd_mbhc_adc_get_hph_thres(struct wcd_mbhc *mbhc) 966 { 967 int hph_threshold, micbias_mv; 968 969 micbias_mv = wcd_mbhc_get_micbias(mbhc); 970 if (mbhc->cfg->hph_thr) { 971 if (mbhc->cfg->micb_mv == micbias_mv) 972 hph_threshold = mbhc->cfg->hph_thr; 973 else 974 hph_threshold = (mbhc->cfg->hph_thr * 975 micbias_mv) / mbhc->cfg->micb_mv; 976 } else { 977 hph_threshold = ((WCD_MBHC_ADC_HPH_THRESHOLD_MV * 978 micbias_mv) / WCD_MBHC_ADC_MICBIAS_MV); 979 } 980 return hph_threshold; 981 } 982 983 static void wcd_mbhc_adc_update_fsm_source(struct wcd_mbhc *mbhc, 984 enum wcd_mbhc_plug_type plug_type) 985 { 986 bool micbias2 = false; 987 988 switch (plug_type) { 989 case MBHC_PLUG_TYPE_HEADPHONE: 990 wcd_mbhc_write_field(mbhc, WCD_MBHC_BTN_ISRC_CTL, 3); 991 break; 992 case MBHC_PLUG_TYPE_HEADSET: 993 if (mbhc->mbhc_cb->micbias_enable_status) 994 micbias2 = mbhc->mbhc_cb->micbias_enable_status(mbhc->component, 995 MIC_BIAS_2); 996 997 if (!mbhc->is_hs_recording && !micbias2) 998 wcd_mbhc_write_field(mbhc, WCD_MBHC_BTN_ISRC_CTL, 3); 999 break; 1000 default: 1001 wcd_mbhc_write_field(mbhc, WCD_MBHC_BTN_ISRC_CTL, 0); 1002 break; 1003 1004 } 1005 } 1006 1007 static void wcd_mbhc_bcs_enable(struct wcd_mbhc *mbhc, int plug_type, bool enable) 1008 { 1009 switch (plug_type) { 1010 case MBHC_PLUG_TYPE_HEADSET: 1011 case MBHC_PLUG_TYPE_HEADPHONE: 1012 if (mbhc->mbhc_cb->bcs_enable) 1013 mbhc->mbhc_cb->bcs_enable(mbhc->component, enable); 1014 break; 1015 default: 1016 break; 1017 } 1018 } 1019 1020 static int wcd_mbhc_get_plug_from_adc(struct wcd_mbhc *mbhc, int adc_result) 1021 1022 { 1023 enum wcd_mbhc_plug_type plug_type; 1024 u32 hph_thr, hs_thr; 1025 1026 hs_thr = wcd_mbhc_adc_get_hs_thres(mbhc); 1027 hph_thr = wcd_mbhc_adc_get_hph_thres(mbhc); 1028 1029 if (adc_result < hph_thr) 1030 plug_type = MBHC_PLUG_TYPE_HEADPHONE; 1031 else if (adc_result > hs_thr) 1032 plug_type = MBHC_PLUG_TYPE_HIGH_HPH; 1033 else 1034 plug_type = MBHC_PLUG_TYPE_HEADSET; 1035 1036 return plug_type; 1037 } 1038 1039 static int wcd_mbhc_get_spl_hs_thres(struct wcd_mbhc *mbhc) 1040 { 1041 int hs_threshold, micbias_mv; 1042 1043 micbias_mv = wcd_mbhc_get_micbias(mbhc); 1044 if (mbhc->cfg->hs_thr && mbhc->cfg->micb_mv != WCD_MBHC_ADC_MICBIAS_MV) { 1045 if (mbhc->cfg->micb_mv == micbias_mv) 1046 hs_threshold = mbhc->cfg->hs_thr; 1047 else 1048 hs_threshold = (mbhc->cfg->hs_thr * micbias_mv) / mbhc->cfg->micb_mv; 1049 } else { 1050 hs_threshold = ((WCD_MBHC_ADC_HS_THRESHOLD_MV * micbias_mv) / 1051 WCD_MBHC_ADC_MICBIAS_MV); 1052 } 1053 return hs_threshold; 1054 } 1055 1056 static bool wcd_mbhc_check_for_spl_headset(struct wcd_mbhc *mbhc) 1057 { 1058 bool is_spl_hs = false; 1059 int output_mv, hs_threshold, hph_threshold; 1060 1061 if (!mbhc->mbhc_cb->mbhc_micb_ctrl_thr_mic) 1062 return false; 1063 1064 /* Bump up MIC_BIAS2 to 2.7V */ 1065 mbhc->mbhc_cb->mbhc_micb_ctrl_thr_mic(mbhc->component, MIC_BIAS_2, true); 1066 usleep_range(10000, 10100); 1067 1068 output_mv = wcd_measure_adc_once(mbhc, MUX_CTL_IN2P); 1069 hs_threshold = wcd_mbhc_get_spl_hs_thres(mbhc); 1070 hph_threshold = wcd_mbhc_adc_get_hph_thres(mbhc); 1071 1072 if (!(output_mv > hs_threshold || output_mv < hph_threshold)) 1073 is_spl_hs = true; 1074 1075 /* Back MIC_BIAS2 to 1.8v if the type is not special headset */ 1076 if (!is_spl_hs) { 1077 mbhc->mbhc_cb->mbhc_micb_ctrl_thr_mic(mbhc->component, MIC_BIAS_2, false); 1078 /* Add 10ms delay for micbias to settle */ 1079 usleep_range(10000, 10100); 1080 } 1081 1082 return is_spl_hs; 1083 } 1084 1085 static void wcd_correct_swch_plug(struct work_struct *work) 1086 { 1087 struct wcd_mbhc *mbhc; 1088 struct snd_soc_component *component; 1089 enum wcd_mbhc_plug_type plug_type = MBHC_PLUG_TYPE_INVALID; 1090 unsigned long timeout; 1091 int pt_gnd_mic_swap_cnt = 0; 1092 int output_mv, cross_conn, hs_threshold, try = 0, micbias_mv; 1093 bool is_spl_hs = false; 1094 bool is_pa_on; 1095 int ret; 1096 1097 mbhc = container_of(work, struct wcd_mbhc, correct_plug_swch); 1098 component = mbhc->component; 1099 1100 ret = pm_runtime_get_sync(component->dev); 1101 if (ret < 0 && ret != -EACCES) { 1102 dev_err_ratelimited(component->dev, 1103 "pm_runtime_get_sync failed in %s, ret %d\n", 1104 __func__, ret); 1105 pm_runtime_put_noidle(component->dev); 1106 return; 1107 } 1108 micbias_mv = wcd_mbhc_get_micbias(mbhc); 1109 hs_threshold = wcd_mbhc_adc_get_hs_thres(mbhc); 1110 1111 /* Mask ADC COMPLETE interrupt */ 1112 disable_irq_nosync(mbhc->intr_ids->mbhc_hs_ins_intr); 1113 1114 /* Check for cross connection */ 1115 do { 1116 cross_conn = wcd_check_cross_conn(mbhc); 1117 try++; 1118 } while (try < GND_MIC_SWAP_THRESHOLD); 1119 1120 if (cross_conn > 0) { 1121 plug_type = MBHC_PLUG_TYPE_GND_MIC_SWAP; 1122 dev_err(mbhc->dev, "cross connection found, Plug type %d\n", 1123 plug_type); 1124 goto correct_plug_type; 1125 } 1126 1127 /* Find plug type */ 1128 output_mv = wcd_measure_adc_continuous(mbhc); 1129 plug_type = wcd_mbhc_get_plug_from_adc(mbhc, output_mv); 1130 1131 /* 1132 * Report plug type if it is either headset or headphone 1133 * else start the 3 sec loop 1134 */ 1135 switch (plug_type) { 1136 case MBHC_PLUG_TYPE_HEADPHONE: 1137 wcd_mbhc_find_plug_and_report(mbhc, plug_type); 1138 break; 1139 case MBHC_PLUG_TYPE_HEADSET: 1140 wcd_mbhc_find_plug_and_report(mbhc, plug_type); 1141 wcd_mbhc_write_field(mbhc, WCD_MBHC_ADC_MODE, 0); 1142 wcd_mbhc_write_field(mbhc, WCD_MBHC_ADC_EN, 0); 1143 wcd_mbhc_write_field(mbhc, WCD_MBHC_DETECTION_DONE, 1); 1144 break; 1145 default: 1146 break; 1147 } 1148 1149 correct_plug_type: 1150 1151 /* Disable BCS slow insertion detection */ 1152 wcd_mbhc_bcs_enable(mbhc, plug_type, false); 1153 1154 timeout = jiffies + msecs_to_jiffies(HS_DETECT_PLUG_TIME_MS); 1155 1156 while (!time_after(jiffies, timeout)) { 1157 if (mbhc->hs_detect_work_stop) { 1158 wcd_micbias_disable(mbhc); 1159 goto exit; 1160 } 1161 1162 msleep(180); 1163 /* 1164 * Use ADC single mode to minimize the chance of missing out 1165 * btn press/release for HEADSET type during correct work. 1166 */ 1167 output_mv = wcd_measure_adc_once(mbhc, MUX_CTL_IN2P); 1168 plug_type = wcd_mbhc_get_plug_from_adc(mbhc, output_mv); 1169 is_pa_on = wcd_mbhc_read_field(mbhc, WCD_MBHC_HPH_PA_EN); 1170 1171 if (output_mv > hs_threshold && !is_spl_hs) { 1172 is_spl_hs = wcd_mbhc_check_for_spl_headset(mbhc); 1173 output_mv = wcd_measure_adc_once(mbhc, MUX_CTL_IN2P); 1174 1175 if (is_spl_hs) { 1176 hs_threshold *= wcd_mbhc_get_micbias(mbhc); 1177 hs_threshold /= micbias_mv; 1178 } 1179 } 1180 1181 if ((output_mv <= hs_threshold) && !is_pa_on) { 1182 /* Check for cross connection*/ 1183 cross_conn = wcd_check_cross_conn(mbhc); 1184 if (cross_conn > 0) { /* cross-connection */ 1185 pt_gnd_mic_swap_cnt++; 1186 if (pt_gnd_mic_swap_cnt < GND_MIC_SWAP_THRESHOLD) 1187 continue; 1188 else 1189 plug_type = MBHC_PLUG_TYPE_GND_MIC_SWAP; 1190 } else if (!cross_conn) { /* no cross connection */ 1191 pt_gnd_mic_swap_cnt = 0; 1192 plug_type = wcd_mbhc_get_plug_from_adc(mbhc, output_mv); 1193 continue; 1194 } else /* Error if (cross_conn < 0) */ 1195 continue; 1196 1197 if (pt_gnd_mic_swap_cnt == GND_MIC_SWAP_THRESHOLD) { 1198 /* US_EU gpio present, flip switch */ 1199 if (mbhc->cfg->swap_gnd_mic) { 1200 if (mbhc->cfg->swap_gnd_mic(component, true)) 1201 continue; 1202 } 1203 } 1204 } 1205 1206 /* cable is extension cable */ 1207 if (output_mv > hs_threshold || mbhc->force_linein) 1208 plug_type = MBHC_PLUG_TYPE_HIGH_HPH; 1209 } 1210 1211 wcd_mbhc_bcs_enable(mbhc, plug_type, true); 1212 1213 if (plug_type == MBHC_PLUG_TYPE_HIGH_HPH) { 1214 if (is_spl_hs) 1215 plug_type = MBHC_PLUG_TYPE_HEADSET; 1216 else 1217 wcd_mbhc_write_field(mbhc, WCD_MBHC_ELECT_ISRC_EN, 1); 1218 } 1219 1220 wcd_mbhc_write_field(mbhc, WCD_MBHC_ADC_MODE, 0); 1221 wcd_mbhc_write_field(mbhc, WCD_MBHC_ADC_EN, 0); 1222 wcd_mbhc_find_plug_and_report(mbhc, plug_type); 1223 1224 /* 1225 * Set DETECTION_DONE bit for HEADSET 1226 * so that btn press/release interrupt can be generated. 1227 * For other plug type, clear the bit. 1228 */ 1229 if (plug_type == MBHC_PLUG_TYPE_HEADSET) 1230 wcd_mbhc_write_field(mbhc, WCD_MBHC_DETECTION_DONE, 1); 1231 else 1232 wcd_mbhc_write_field(mbhc, WCD_MBHC_DETECTION_DONE, 0); 1233 1234 if (mbhc->mbhc_cb->mbhc_micbias_control) 1235 wcd_mbhc_adc_update_fsm_source(mbhc, plug_type); 1236 1237 exit: 1238 if (mbhc->mbhc_cb->mbhc_micbias_control/* && !mbhc->micbias_enable*/) 1239 mbhc->mbhc_cb->mbhc_micbias_control(component, MIC_BIAS_2, MICB_DISABLE); 1240 1241 /* 1242 * If plug type is corrected from special headset to headphone, 1243 * clear the micbias enable flag, set micbias back to 1.8V and 1244 * disable micbias. 1245 */ 1246 if (plug_type == MBHC_PLUG_TYPE_HEADPHONE) { 1247 wcd_micbias_disable(mbhc); 1248 /* 1249 * Enable ADC COMPLETE interrupt for HEADPHONE. 1250 * Btn release may happen after the correct work, ADC COMPLETE 1251 * interrupt needs to be captured to correct plug type. 1252 */ 1253 enable_irq(mbhc->intr_ids->mbhc_hs_ins_intr); 1254 } 1255 1256 if (mbhc->mbhc_cb->hph_pull_down_ctrl) 1257 mbhc->mbhc_cb->hph_pull_down_ctrl(component, true); 1258 1259 pm_runtime_mark_last_busy(component->dev); 1260 pm_runtime_put_autosuspend(component->dev); 1261 } 1262 1263 static irqreturn_t wcd_mbhc_adc_hs_rem_irq(int irq, void *data) 1264 { 1265 struct wcd_mbhc *mbhc = data; 1266 unsigned long timeout; 1267 int adc_threshold, output_mv, retry = 0; 1268 1269 mutex_lock(&mbhc->lock); 1270 timeout = jiffies + msecs_to_jiffies(WCD_FAKE_REMOVAL_MIN_PERIOD_MS); 1271 adc_threshold = wcd_mbhc_adc_get_hs_thres(mbhc); 1272 1273 do { 1274 retry++; 1275 /* 1276 * read output_mv every 10ms to look for 1277 * any change in IN2_P 1278 */ 1279 usleep_range(10000, 10100); 1280 output_mv = wcd_measure_adc_once(mbhc, MUX_CTL_IN2P); 1281 1282 /* Check for fake removal */ 1283 if ((output_mv <= adc_threshold) && retry > FAKE_REM_RETRY_ATTEMPTS) 1284 goto exit; 1285 } while (!time_after(jiffies, timeout)); 1286 1287 /* 1288 * ADC COMPLETE and ELEC_REM interrupts are both enabled for 1289 * HEADPHONE, need to reject the ADC COMPLETE interrupt which 1290 * follows ELEC_REM one when HEADPHONE is removed. 1291 */ 1292 if (mbhc->current_plug == MBHC_PLUG_TYPE_HEADPHONE) 1293 mbhc->extn_cable_hph_rem = true; 1294 1295 wcd_mbhc_write_field(mbhc, WCD_MBHC_DETECTION_DONE, 0); 1296 wcd_mbhc_write_field(mbhc, WCD_MBHC_ADC_MODE, 0); 1297 wcd_mbhc_write_field(mbhc, WCD_MBHC_ADC_EN, 0); 1298 wcd_mbhc_elec_hs_report_unplug(mbhc); 1299 wcd_mbhc_write_field(mbhc, WCD_MBHC_BTN_ISRC_CTL, 0); 1300 1301 exit: 1302 mutex_unlock(&mbhc->lock); 1303 return IRQ_HANDLED; 1304 } 1305 1306 static irqreturn_t wcd_mbhc_adc_hs_ins_irq(int irq, void *data) 1307 { 1308 struct wcd_mbhc *mbhc = data; 1309 u8 clamp_state; 1310 u8 clamp_retry = WCD_MBHC_FAKE_INS_RETRY; 1311 1312 /* 1313 * ADC COMPLETE and ELEC_REM interrupts are both enabled for HEADPHONE, 1314 * need to reject the ADC COMPLETE interrupt which follows ELEC_REM one 1315 * when HEADPHONE is removed. 1316 */ 1317 if (mbhc->extn_cable_hph_rem == true) { 1318 mbhc->extn_cable_hph_rem = false; 1319 return IRQ_HANDLED; 1320 } 1321 1322 do { 1323 clamp_state = wcd_mbhc_read_field(mbhc, WCD_MBHC_IN2P_CLAMP_STATE); 1324 if (clamp_state) 1325 return IRQ_HANDLED; 1326 /* 1327 * check clamp for 120ms but at 30ms chunks to leave 1328 * room for other interrupts to be processed 1329 */ 1330 usleep_range(30000, 30100); 1331 } while (--clamp_retry); 1332 1333 /* 1334 * If current plug is headphone then there is no chance to 1335 * get ADC complete interrupt, so connected cable should be 1336 * headset not headphone. 1337 */ 1338 if (mbhc->current_plug == MBHC_PLUG_TYPE_HEADPHONE) { 1339 disable_irq_nosync(mbhc->intr_ids->mbhc_hs_ins_intr); 1340 wcd_mbhc_write_field(mbhc, WCD_MBHC_DETECTION_DONE, 1); 1341 wcd_mbhc_find_plug_and_report(mbhc, MBHC_PLUG_TYPE_HEADSET); 1342 return IRQ_HANDLED; 1343 } 1344 1345 return IRQ_HANDLED; 1346 } 1347 1348 int wcd_mbhc_get_impedance(struct wcd_mbhc *mbhc, uint32_t *zl, uint32_t *zr) 1349 { 1350 *zl = mbhc->zl; 1351 *zr = mbhc->zr; 1352 1353 if (*zl && *zr) 1354 return 0; 1355 else 1356 return -EINVAL; 1357 } 1358 EXPORT_SYMBOL(wcd_mbhc_get_impedance); 1359 1360 void wcd_mbhc_set_hph_type(struct wcd_mbhc *mbhc, int hph_type) 1361 { 1362 mbhc->hph_type = hph_type; 1363 } 1364 EXPORT_SYMBOL(wcd_mbhc_set_hph_type); 1365 1366 int wcd_mbhc_get_hph_type(struct wcd_mbhc *mbhc) 1367 { 1368 return mbhc->hph_type; 1369 } 1370 EXPORT_SYMBOL(wcd_mbhc_get_hph_type); 1371 1372 int wcd_mbhc_start(struct wcd_mbhc *mbhc, struct wcd_mbhc_config *cfg, 1373 struct snd_soc_jack *jack) 1374 { 1375 if (!mbhc || !cfg || !jack) 1376 return -EINVAL; 1377 1378 mbhc->cfg = cfg; 1379 mbhc->jack = jack; 1380 1381 return wcd_mbhc_initialise(mbhc); 1382 } 1383 EXPORT_SYMBOL(wcd_mbhc_start); 1384 1385 void wcd_mbhc_stop(struct wcd_mbhc *mbhc) 1386 { 1387 mbhc->current_plug = MBHC_PLUG_TYPE_NONE; 1388 mbhc->hph_status = 0; 1389 disable_irq_nosync(mbhc->intr_ids->hph_left_ocp); 1390 disable_irq_nosync(mbhc->intr_ids->hph_right_ocp); 1391 } 1392 EXPORT_SYMBOL(wcd_mbhc_stop); 1393 1394 int wcd_dt_parse_mbhc_data(struct device *dev, struct wcd_mbhc_config *cfg) 1395 { 1396 struct device_node *np = dev->of_node; 1397 int ret, i, microvolt; 1398 1399 if (of_property_read_bool(np, "qcom,hphl-jack-type-normally-closed")) 1400 cfg->hphl_swh = false; 1401 else 1402 cfg->hphl_swh = true; 1403 1404 if (of_property_read_bool(np, "qcom,ground-jack-type-normally-closed")) 1405 cfg->gnd_swh = false; 1406 else 1407 cfg->gnd_swh = true; 1408 1409 ret = of_property_read_u32(np, "qcom,mbhc-headset-vthreshold-microvolt", 1410 µvolt); 1411 if (ret) 1412 dev_dbg(dev, "missing qcom,mbhc-hs-mic-max-vthreshold--microvolt in dt node\n"); 1413 else 1414 cfg->hs_thr = microvolt/1000; 1415 1416 ret = of_property_read_u32(np, "qcom,mbhc-headphone-vthreshold-microvolt", 1417 µvolt); 1418 if (ret) 1419 dev_dbg(dev, "missing qcom,mbhc-hs-mic-min-vthreshold-microvolt entry\n"); 1420 else 1421 cfg->hph_thr = microvolt/1000; 1422 1423 ret = of_property_read_u32_array(np, 1424 "qcom,mbhc-buttons-vthreshold-microvolt", 1425 &cfg->btn_high[0], 1426 WCD_MBHC_DEF_BUTTONS); 1427 if (ret) 1428 dev_err(dev, "missing qcom,mbhc-buttons-vthreshold-microvolt entry\n"); 1429 1430 for (i = 0; i < WCD_MBHC_DEF_BUTTONS; i++) { 1431 if (ret) /* default voltage */ 1432 cfg->btn_high[i] = 500000; 1433 else 1434 /* Micro to Milli Volts */ 1435 cfg->btn_high[i] = cfg->btn_high[i]/1000; 1436 } 1437 1438 return 0; 1439 } 1440 EXPORT_SYMBOL(wcd_dt_parse_mbhc_data); 1441 1442 struct wcd_mbhc *wcd_mbhc_init(struct snd_soc_component *component, 1443 const struct wcd_mbhc_cb *mbhc_cb, 1444 const struct wcd_mbhc_intr *intr_ids, 1445 struct wcd_mbhc_field *fields, 1446 bool impedance_det_en) 1447 { 1448 struct device *dev = component->dev; 1449 struct wcd_mbhc *mbhc; 1450 int ret; 1451 1452 if (!intr_ids || !fields || !mbhc_cb || !mbhc_cb->mbhc_bias || !mbhc_cb->set_btn_thr) { 1453 dev_err(dev, "%s: Insufficient mbhc configuration\n", __func__); 1454 return ERR_PTR(-EINVAL); 1455 } 1456 1457 mbhc = kzalloc(sizeof(*mbhc), GFP_KERNEL); 1458 if (!mbhc) 1459 return ERR_PTR(-ENOMEM); 1460 1461 mbhc->component = component; 1462 mbhc->dev = dev; 1463 mbhc->intr_ids = intr_ids; 1464 mbhc->mbhc_cb = mbhc_cb; 1465 mbhc->fields = fields; 1466 mbhc->mbhc_detection_logic = WCD_DETECTION_ADC; 1467 1468 if (mbhc_cb->compute_impedance) 1469 mbhc->impedance_detect = impedance_det_en; 1470 1471 INIT_DELAYED_WORK(&mbhc->mbhc_btn_dwork, wcd_btn_long_press_fn); 1472 1473 mutex_init(&mbhc->lock); 1474 1475 INIT_WORK(&mbhc->correct_plug_swch, wcd_correct_swch_plug); 1476 1477 ret = request_threaded_irq(mbhc->intr_ids->mbhc_sw_intr, NULL, 1478 wcd_mbhc_mech_plug_detect_irq, 1479 IRQF_ONESHOT | IRQF_TRIGGER_RISING, 1480 "mbhc sw intr", mbhc); 1481 if (ret) 1482 goto err_free_mbhc; 1483 1484 ret = request_threaded_irq(mbhc->intr_ids->mbhc_btn_press_intr, NULL, 1485 wcd_mbhc_btn_press_handler, 1486 IRQF_ONESHOT | IRQF_TRIGGER_RISING, 1487 "Button Press detect", mbhc); 1488 if (ret) 1489 goto err_free_sw_intr; 1490 1491 ret = request_threaded_irq(mbhc->intr_ids->mbhc_btn_release_intr, NULL, 1492 wcd_mbhc_btn_release_handler, 1493 IRQF_ONESHOT | IRQF_TRIGGER_RISING, 1494 "Button Release detect", mbhc); 1495 if (ret) 1496 goto err_free_btn_press_intr; 1497 1498 ret = request_threaded_irq(mbhc->intr_ids->mbhc_hs_ins_intr, NULL, 1499 wcd_mbhc_adc_hs_ins_irq, 1500 IRQF_ONESHOT | IRQF_TRIGGER_RISING, 1501 "Elect Insert", mbhc); 1502 if (ret) 1503 goto err_free_btn_release_intr; 1504 1505 disable_irq_nosync(mbhc->intr_ids->mbhc_hs_ins_intr); 1506 1507 ret = request_threaded_irq(mbhc->intr_ids->mbhc_hs_rem_intr, NULL, 1508 wcd_mbhc_adc_hs_rem_irq, 1509 IRQF_ONESHOT | IRQF_TRIGGER_RISING, 1510 "Elect Remove", mbhc); 1511 if (ret) 1512 goto err_free_hs_ins_intr; 1513 1514 disable_irq_nosync(mbhc->intr_ids->mbhc_hs_rem_intr); 1515 1516 ret = request_threaded_irq(mbhc->intr_ids->hph_left_ocp, NULL, 1517 wcd_mbhc_hphl_ocp_irq, 1518 IRQF_ONESHOT | IRQF_TRIGGER_RISING, 1519 "HPH_L OCP detect", mbhc); 1520 if (ret) 1521 goto err_free_hs_rem_intr; 1522 1523 ret = request_threaded_irq(mbhc->intr_ids->hph_right_ocp, NULL, 1524 wcd_mbhc_hphr_ocp_irq, 1525 IRQF_ONESHOT | IRQF_TRIGGER_RISING, 1526 "HPH_R OCP detect", mbhc); 1527 if (ret) 1528 goto err_free_hph_left_ocp; 1529 1530 return mbhc; 1531 1532 err_free_hph_left_ocp: 1533 free_irq(mbhc->intr_ids->hph_left_ocp, mbhc); 1534 err_free_hs_rem_intr: 1535 free_irq(mbhc->intr_ids->mbhc_hs_rem_intr, mbhc); 1536 err_free_hs_ins_intr: 1537 free_irq(mbhc->intr_ids->mbhc_hs_ins_intr, mbhc); 1538 err_free_btn_release_intr: 1539 free_irq(mbhc->intr_ids->mbhc_btn_release_intr, mbhc); 1540 err_free_btn_press_intr: 1541 free_irq(mbhc->intr_ids->mbhc_btn_press_intr, mbhc); 1542 err_free_sw_intr: 1543 free_irq(mbhc->intr_ids->mbhc_sw_intr, mbhc); 1544 err_free_mbhc: 1545 kfree(mbhc); 1546 1547 dev_err(dev, "Failed to request mbhc interrupts %d\n", ret); 1548 1549 return ERR_PTR(ret); 1550 } 1551 EXPORT_SYMBOL(wcd_mbhc_init); 1552 1553 void wcd_mbhc_deinit(struct wcd_mbhc *mbhc) 1554 { 1555 free_irq(mbhc->intr_ids->hph_right_ocp, mbhc); 1556 free_irq(mbhc->intr_ids->hph_left_ocp, mbhc); 1557 free_irq(mbhc->intr_ids->mbhc_hs_rem_intr, mbhc); 1558 free_irq(mbhc->intr_ids->mbhc_hs_ins_intr, mbhc); 1559 free_irq(mbhc->intr_ids->mbhc_btn_release_intr, mbhc); 1560 free_irq(mbhc->intr_ids->mbhc_btn_press_intr, mbhc); 1561 free_irq(mbhc->intr_ids->mbhc_sw_intr, mbhc); 1562 1563 mutex_lock(&mbhc->lock); 1564 wcd_cancel_hs_detect_plug(mbhc, &mbhc->correct_plug_swch); 1565 mutex_unlock(&mbhc->lock); 1566 1567 kfree(mbhc); 1568 } 1569 EXPORT_SYMBOL(wcd_mbhc_deinit); 1570 1571 static int __init mbhc_init(void) 1572 { 1573 return 0; 1574 } 1575 1576 static void __exit mbhc_exit(void) 1577 { 1578 } 1579 1580 module_init(mbhc_init); 1581 module_exit(mbhc_exit); 1582 1583 MODULE_DESCRIPTION("wcd MBHC v2 module"); 1584 MODULE_LICENSE("GPL"); 1585