1 // SPDX-License-Identifier: GPL-2.0-or-later 2 /* 3 * TAS5086 ASoC codec driver 4 * 5 * Copyright (c) 2013 Daniel Mack <zonque@gmail.com> 6 * 7 * TODO: 8 * - implement DAPM and input muxing 9 * - implement modulation limit 10 * - implement non-default PWM start 11 * 12 * Note that this chip has a very unusual register layout, specifically 13 * because the registers are of unequal size, and multi-byte registers 14 * require bulk writes to take effect. Regmap does not support that kind 15 * of devices. 16 * 17 * Currently, the driver does not touch any of the registers >= 0x20, so 18 * it doesn't matter because the entire map can be accessed as 8-bit 19 * array. In case more features will be added in the future 20 * that require access to higher registers, the entire regmap H/W I/O 21 * routines have to be open-coded. 22 */ 23 24 #include <linux/module.h> 25 #include <linux/slab.h> 26 #include <linux/delay.h> 27 #include <linux/gpio/consumer.h> 28 #include <linux/i2c.h> 29 #include <linux/regmap.h> 30 #include <linux/regulator/consumer.h> 31 #include <linux/spi/spi.h> 32 #include <linux/of.h> 33 #include <linux/of_device.h> 34 #include <sound/pcm.h> 35 #include <sound/pcm_params.h> 36 #include <sound/soc.h> 37 #include <sound/tlv.h> 38 #include <sound/tas5086.h> 39 40 #define TAS5086_PCM_FORMATS (SNDRV_PCM_FMTBIT_S16_LE | \ 41 SNDRV_PCM_FMTBIT_S20_3LE | \ 42 SNDRV_PCM_FMTBIT_S24_3LE) 43 44 #define TAS5086_PCM_RATES (SNDRV_PCM_RATE_32000 | SNDRV_PCM_RATE_44100 | \ 45 SNDRV_PCM_RATE_48000 | SNDRV_PCM_RATE_88200 | \ 46 SNDRV_PCM_RATE_96000 | SNDRV_PCM_RATE_176400 | \ 47 SNDRV_PCM_RATE_192000) 48 49 /* 50 * TAS5086 registers 51 */ 52 #define TAS5086_CLOCK_CONTROL 0x00 /* Clock control register */ 53 #define TAS5086_CLOCK_RATE(val) (val << 5) 54 #define TAS5086_CLOCK_RATE_MASK (0x7 << 5) 55 #define TAS5086_CLOCK_RATIO(val) (val << 2) 56 #define TAS5086_CLOCK_RATIO_MASK (0x7 << 2) 57 #define TAS5086_CLOCK_SCLK_RATIO_48 (1 << 1) 58 #define TAS5086_CLOCK_VALID (1 << 0) 59 60 #define TAS5086_DEEMPH_MASK 0x03 61 #define TAS5086_SOFT_MUTE_ALL 0x3f 62 63 #define TAS5086_DEV_ID 0x01 /* Device ID register */ 64 #define TAS5086_ERROR_STATUS 0x02 /* Error status register */ 65 #define TAS5086_SYS_CONTROL_1 0x03 /* System control register 1 */ 66 #define TAS5086_SERIAL_DATA_IF 0x04 /* Serial data interface register */ 67 #define TAS5086_SYS_CONTROL_2 0x05 /* System control register 2 */ 68 #define TAS5086_SOFT_MUTE 0x06 /* Soft mute register */ 69 #define TAS5086_MASTER_VOL 0x07 /* Master volume */ 70 #define TAS5086_CHANNEL_VOL(X) (0x08 + (X)) /* Channel 1-6 volume */ 71 #define TAS5086_VOLUME_CONTROL 0x09 /* Volume control register */ 72 #define TAS5086_MOD_LIMIT 0x10 /* Modulation limit register */ 73 #define TAS5086_PWM_START 0x18 /* PWM start register */ 74 #define TAS5086_SURROUND 0x19 /* Surround register */ 75 #define TAS5086_SPLIT_CAP_CHARGE 0x1a /* Split cap charge period register */ 76 #define TAS5086_OSC_TRIM 0x1b /* Oscillator trim register */ 77 #define TAS5086_BKNDERR 0x1c 78 #define TAS5086_INPUT_MUX 0x20 79 #define TAS5086_PWM_OUTPUT_MUX 0x25 80 81 #define TAS5086_MAX_REGISTER TAS5086_PWM_OUTPUT_MUX 82 83 #define TAS5086_PWM_START_MIDZ_FOR_START_1 (1 << 7) 84 #define TAS5086_PWM_START_MIDZ_FOR_START_2 (1 << 6) 85 #define TAS5086_PWM_START_CHANNEL_MASK (0x3f) 86 87 /* 88 * Default TAS5086 power-up configuration 89 */ 90 static const struct reg_default tas5086_reg_defaults[] = { 91 { 0x00, 0x6c }, 92 { 0x01, 0x03 }, 93 { 0x02, 0x00 }, 94 { 0x03, 0xa0 }, 95 { 0x04, 0x05 }, 96 { 0x05, 0x60 }, 97 { 0x06, 0x00 }, 98 { 0x07, 0xff }, 99 { 0x08, 0x30 }, 100 { 0x09, 0x30 }, 101 { 0x0a, 0x30 }, 102 { 0x0b, 0x30 }, 103 { 0x0c, 0x30 }, 104 { 0x0d, 0x30 }, 105 { 0x0e, 0xb1 }, 106 { 0x0f, 0x00 }, 107 { 0x10, 0x02 }, 108 { 0x11, 0x00 }, 109 { 0x12, 0x00 }, 110 { 0x13, 0x00 }, 111 { 0x14, 0x00 }, 112 { 0x15, 0x00 }, 113 { 0x16, 0x00 }, 114 { 0x17, 0x00 }, 115 { 0x18, 0x3f }, 116 { 0x19, 0x00 }, 117 { 0x1a, 0x18 }, 118 { 0x1b, 0x82 }, 119 { 0x1c, 0x05 }, 120 }; 121 122 static int tas5086_register_size(struct device *dev, unsigned int reg) 123 { 124 switch (reg) { 125 case TAS5086_CLOCK_CONTROL ... TAS5086_BKNDERR: 126 return 1; 127 case TAS5086_INPUT_MUX: 128 case TAS5086_PWM_OUTPUT_MUX: 129 return 4; 130 } 131 132 dev_err(dev, "Unsupported register address: %d\n", reg); 133 return 0; 134 } 135 136 static bool tas5086_accessible_reg(struct device *dev, unsigned int reg) 137 { 138 switch (reg) { 139 case 0x0f: 140 case 0x11 ... 0x17: 141 case 0x1d ... 0x1f: 142 return false; 143 default: 144 return true; 145 } 146 } 147 148 static bool tas5086_volatile_reg(struct device *dev, unsigned int reg) 149 { 150 switch (reg) { 151 case TAS5086_DEV_ID: 152 case TAS5086_ERROR_STATUS: 153 return true; 154 } 155 156 return false; 157 } 158 159 static bool tas5086_writeable_reg(struct device *dev, unsigned int reg) 160 { 161 return tas5086_accessible_reg(dev, reg) && (reg != TAS5086_DEV_ID); 162 } 163 164 static int tas5086_reg_write(void *context, unsigned int reg, 165 unsigned int value) 166 { 167 struct i2c_client *client = context; 168 unsigned int i, size; 169 uint8_t buf[5]; 170 int ret; 171 172 size = tas5086_register_size(&client->dev, reg); 173 if (size == 0) 174 return -EINVAL; 175 176 buf[0] = reg; 177 178 for (i = size; i >= 1; --i) { 179 buf[i] = value; 180 value >>= 8; 181 } 182 183 ret = i2c_master_send(client, buf, size + 1); 184 if (ret == size + 1) 185 return 0; 186 else if (ret < 0) 187 return ret; 188 else 189 return -EIO; 190 } 191 192 static int tas5086_reg_read(void *context, unsigned int reg, 193 unsigned int *value) 194 { 195 struct i2c_client *client = context; 196 uint8_t send_buf, recv_buf[4]; 197 struct i2c_msg msgs[2]; 198 unsigned int size; 199 unsigned int i; 200 int ret; 201 202 size = tas5086_register_size(&client->dev, reg); 203 if (size == 0) 204 return -EINVAL; 205 206 send_buf = reg; 207 208 msgs[0].addr = client->addr; 209 msgs[0].len = sizeof(send_buf); 210 msgs[0].buf = &send_buf; 211 msgs[0].flags = 0; 212 213 msgs[1].addr = client->addr; 214 msgs[1].len = size; 215 msgs[1].buf = recv_buf; 216 msgs[1].flags = I2C_M_RD; 217 218 ret = i2c_transfer(client->adapter, msgs, ARRAY_SIZE(msgs)); 219 if (ret < 0) 220 return ret; 221 else if (ret != ARRAY_SIZE(msgs)) 222 return -EIO; 223 224 *value = 0; 225 226 for (i = 0; i < size; i++) { 227 *value <<= 8; 228 *value |= recv_buf[i]; 229 } 230 231 return 0; 232 } 233 234 static const char * const supply_names[] = { 235 "dvdd", "avdd" 236 }; 237 238 struct tas5086_private { 239 struct regmap *regmap; 240 unsigned int mclk, sclk; 241 unsigned int format; 242 bool deemph; 243 unsigned int charge_period; 244 unsigned int pwm_start_mid_z; 245 /* Current sample rate for de-emphasis control */ 246 int rate; 247 /* GPIO driving Reset pin, if any */ 248 struct gpio_desc *reset; 249 struct regulator_bulk_data supplies[ARRAY_SIZE(supply_names)]; 250 }; 251 252 static int tas5086_deemph[] = { 0, 32000, 44100, 48000 }; 253 254 static int tas5086_set_deemph(struct snd_soc_component *component) 255 { 256 struct tas5086_private *priv = snd_soc_component_get_drvdata(component); 257 int i, val = 0; 258 259 if (priv->deemph) { 260 for (i = 0; i < ARRAY_SIZE(tas5086_deemph); i++) { 261 if (tas5086_deemph[i] == priv->rate) { 262 val = i; 263 break; 264 } 265 } 266 } 267 268 return regmap_update_bits(priv->regmap, TAS5086_SYS_CONTROL_1, 269 TAS5086_DEEMPH_MASK, val); 270 } 271 272 static int tas5086_get_deemph(struct snd_kcontrol *kcontrol, 273 struct snd_ctl_elem_value *ucontrol) 274 { 275 struct snd_soc_component *component = snd_soc_kcontrol_component(kcontrol); 276 struct tas5086_private *priv = snd_soc_component_get_drvdata(component); 277 278 ucontrol->value.integer.value[0] = priv->deemph; 279 280 return 0; 281 } 282 283 static int tas5086_put_deemph(struct snd_kcontrol *kcontrol, 284 struct snd_ctl_elem_value *ucontrol) 285 { 286 struct snd_soc_component *component = snd_soc_kcontrol_component(kcontrol); 287 struct tas5086_private *priv = snd_soc_component_get_drvdata(component); 288 289 priv->deemph = ucontrol->value.integer.value[0]; 290 291 return tas5086_set_deemph(component); 292 } 293 294 295 static int tas5086_set_dai_sysclk(struct snd_soc_dai *codec_dai, 296 int clk_id, unsigned int freq, int dir) 297 { 298 struct snd_soc_component *component = codec_dai->component; 299 struct tas5086_private *priv = snd_soc_component_get_drvdata(component); 300 301 switch (clk_id) { 302 case TAS5086_CLK_IDX_MCLK: 303 priv->mclk = freq; 304 break; 305 case TAS5086_CLK_IDX_SCLK: 306 priv->sclk = freq; 307 break; 308 } 309 310 return 0; 311 } 312 313 static int tas5086_set_dai_fmt(struct snd_soc_dai *codec_dai, 314 unsigned int format) 315 { 316 struct snd_soc_component *component = codec_dai->component; 317 struct tas5086_private *priv = snd_soc_component_get_drvdata(component); 318 319 /* The TAS5086 can only be slave to all clocks */ 320 if ((format & SND_SOC_DAIFMT_CLOCK_PROVIDER_MASK) != SND_SOC_DAIFMT_CBC_CFC) { 321 dev_err(component->dev, "Invalid clocking mode\n"); 322 return -EINVAL; 323 } 324 325 /* we need to refer to the data format from hw_params() */ 326 priv->format = format; 327 328 return 0; 329 } 330 331 static const int tas5086_sample_rates[] = { 332 32000, 38000, 44100, 48000, 88200, 96000, 176400, 192000 333 }; 334 335 static const int tas5086_ratios[] = { 336 64, 128, 192, 256, 384, 512 337 }; 338 339 static int index_in_array(const int *array, int len, int needle) 340 { 341 int i; 342 343 for (i = 0; i < len; i++) 344 if (array[i] == needle) 345 return i; 346 347 return -ENOENT; 348 } 349 350 static int tas5086_hw_params(struct snd_pcm_substream *substream, 351 struct snd_pcm_hw_params *params, 352 struct snd_soc_dai *dai) 353 { 354 struct snd_soc_component *component = dai->component; 355 struct tas5086_private *priv = snd_soc_component_get_drvdata(component); 356 int val; 357 int ret; 358 359 priv->rate = params_rate(params); 360 361 /* Look up the sample rate and refer to the offset in the list */ 362 val = index_in_array(tas5086_sample_rates, 363 ARRAY_SIZE(tas5086_sample_rates), priv->rate); 364 365 if (val < 0) { 366 dev_err(component->dev, "Invalid sample rate\n"); 367 return -EINVAL; 368 } 369 370 ret = regmap_update_bits(priv->regmap, TAS5086_CLOCK_CONTROL, 371 TAS5086_CLOCK_RATE_MASK, 372 TAS5086_CLOCK_RATE(val)); 373 if (ret < 0) 374 return ret; 375 376 /* MCLK / Fs ratio */ 377 val = index_in_array(tas5086_ratios, ARRAY_SIZE(tas5086_ratios), 378 priv->mclk / priv->rate); 379 if (val < 0) { 380 dev_err(component->dev, "Invalid MCLK / Fs ratio\n"); 381 return -EINVAL; 382 } 383 384 ret = regmap_update_bits(priv->regmap, TAS5086_CLOCK_CONTROL, 385 TAS5086_CLOCK_RATIO_MASK, 386 TAS5086_CLOCK_RATIO(val)); 387 if (ret < 0) 388 return ret; 389 390 391 ret = regmap_update_bits(priv->regmap, TAS5086_CLOCK_CONTROL, 392 TAS5086_CLOCK_SCLK_RATIO_48, 393 (priv->sclk == 48 * priv->rate) ? 394 TAS5086_CLOCK_SCLK_RATIO_48 : 0); 395 if (ret < 0) 396 return ret; 397 398 /* 399 * The chip has a very unituitive register mapping and muxes information 400 * about data format and sample depth into the same register, but not on 401 * a logical bit-boundary. Hence, we have to refer to the format passed 402 * in the set_dai_fmt() callback and set up everything from here. 403 * 404 * First, determine the 'base' value, using the format ... 405 */ 406 switch (priv->format & SND_SOC_DAIFMT_FORMAT_MASK) { 407 case SND_SOC_DAIFMT_RIGHT_J: 408 val = 0x00; 409 break; 410 case SND_SOC_DAIFMT_I2S: 411 val = 0x03; 412 break; 413 case SND_SOC_DAIFMT_LEFT_J: 414 val = 0x06; 415 break; 416 default: 417 dev_err(component->dev, "Invalid DAI format\n"); 418 return -EINVAL; 419 } 420 421 /* ... then add the offset for the sample bit depth. */ 422 switch (params_width(params)) { 423 case 16: 424 val += 0; 425 break; 426 case 20: 427 val += 1; 428 break; 429 case 24: 430 val += 2; 431 break; 432 default: 433 dev_err(component->dev, "Invalid bit width\n"); 434 return -EINVAL; 435 } 436 437 ret = regmap_write(priv->regmap, TAS5086_SERIAL_DATA_IF, val); 438 if (ret < 0) 439 return ret; 440 441 /* clock is considered valid now */ 442 ret = regmap_update_bits(priv->regmap, TAS5086_CLOCK_CONTROL, 443 TAS5086_CLOCK_VALID, TAS5086_CLOCK_VALID); 444 if (ret < 0) 445 return ret; 446 447 return tas5086_set_deemph(component); 448 } 449 450 static int tas5086_mute_stream(struct snd_soc_dai *dai, int mute, int stream) 451 { 452 struct snd_soc_component *component = dai->component; 453 struct tas5086_private *priv = snd_soc_component_get_drvdata(component); 454 unsigned int val = 0; 455 456 if (mute) 457 val = TAS5086_SOFT_MUTE_ALL; 458 459 return regmap_write(priv->regmap, TAS5086_SOFT_MUTE, val); 460 } 461 462 static void tas5086_reset(struct tas5086_private *priv) 463 { 464 if (priv->reset) { 465 /* Reset codec - minimum assertion time is 400ns */ 466 gpiod_direction_output(priv->reset, 1); 467 udelay(1); 468 gpiod_set_value(priv->reset, 0); 469 470 /* Codec needs ~15ms to wake up */ 471 msleep(15); 472 } 473 } 474 475 /* charge period values in microseconds */ 476 static const int tas5086_charge_period[] = { 477 13000, 16900, 23400, 31200, 41600, 54600, 72800, 96200, 478 130000, 156000, 234000, 312000, 416000, 546000, 728000, 962000, 479 1300000, 169000, 2340000, 3120000, 4160000, 5460000, 7280000, 9620000, 480 }; 481 482 static int tas5086_init(struct device *dev, struct tas5086_private *priv) 483 { 484 int ret, i; 485 486 /* 487 * If any of the channels is configured to start in Mid-Z mode, 488 * configure 'part 1' of the PWM starts to use Mid-Z, and tell 489 * all configured mid-z channels to start under 'part 1'. 490 */ 491 if (priv->pwm_start_mid_z) 492 regmap_write(priv->regmap, TAS5086_PWM_START, 493 TAS5086_PWM_START_MIDZ_FOR_START_1 | 494 priv->pwm_start_mid_z); 495 496 /* lookup and set split-capacitor charge period */ 497 if (priv->charge_period == 0) { 498 regmap_write(priv->regmap, TAS5086_SPLIT_CAP_CHARGE, 0); 499 } else { 500 i = index_in_array(tas5086_charge_period, 501 ARRAY_SIZE(tas5086_charge_period), 502 priv->charge_period); 503 if (i >= 0) 504 regmap_write(priv->regmap, TAS5086_SPLIT_CAP_CHARGE, 505 i + 0x08); 506 else 507 dev_warn(dev, 508 "Invalid split-cap charge period of %d ns.\n", 509 priv->charge_period); 510 } 511 512 /* enable factory trim */ 513 ret = regmap_write(priv->regmap, TAS5086_OSC_TRIM, 0x00); 514 if (ret < 0) 515 return ret; 516 517 /* start all channels */ 518 ret = regmap_write(priv->regmap, TAS5086_SYS_CONTROL_2, 0x20); 519 if (ret < 0) 520 return ret; 521 522 /* mute all channels for now */ 523 ret = regmap_write(priv->regmap, TAS5086_SOFT_MUTE, 524 TAS5086_SOFT_MUTE_ALL); 525 if (ret < 0) 526 return ret; 527 528 return 0; 529 } 530 531 /* TAS5086 controls */ 532 static const DECLARE_TLV_DB_SCALE(tas5086_dac_tlv, -10350, 50, 1); 533 534 static const struct snd_kcontrol_new tas5086_controls[] = { 535 SOC_SINGLE_TLV("Master Playback Volume", TAS5086_MASTER_VOL, 536 0, 0xff, 1, tas5086_dac_tlv), 537 SOC_DOUBLE_R_TLV("Channel 1/2 Playback Volume", 538 TAS5086_CHANNEL_VOL(0), TAS5086_CHANNEL_VOL(1), 539 0, 0xff, 1, tas5086_dac_tlv), 540 SOC_DOUBLE_R_TLV("Channel 3/4 Playback Volume", 541 TAS5086_CHANNEL_VOL(2), TAS5086_CHANNEL_VOL(3), 542 0, 0xff, 1, tas5086_dac_tlv), 543 SOC_DOUBLE_R_TLV("Channel 5/6 Playback Volume", 544 TAS5086_CHANNEL_VOL(4), TAS5086_CHANNEL_VOL(5), 545 0, 0xff, 1, tas5086_dac_tlv), 546 SOC_SINGLE_BOOL_EXT("De-emphasis Switch", 0, 547 tas5086_get_deemph, tas5086_put_deemph), 548 }; 549 550 /* Input mux controls */ 551 static const char *tas5086_dapm_sdin_texts[] = 552 { 553 "SDIN1-L", "SDIN1-R", "SDIN2-L", "SDIN2-R", 554 "SDIN3-L", "SDIN3-R", "Ground (0)", "nc" 555 }; 556 557 static const struct soc_enum tas5086_dapm_input_mux_enum[] = { 558 SOC_ENUM_SINGLE(TAS5086_INPUT_MUX, 20, 8, tas5086_dapm_sdin_texts), 559 SOC_ENUM_SINGLE(TAS5086_INPUT_MUX, 16, 8, tas5086_dapm_sdin_texts), 560 SOC_ENUM_SINGLE(TAS5086_INPUT_MUX, 12, 8, tas5086_dapm_sdin_texts), 561 SOC_ENUM_SINGLE(TAS5086_INPUT_MUX, 8, 8, tas5086_dapm_sdin_texts), 562 SOC_ENUM_SINGLE(TAS5086_INPUT_MUX, 4, 8, tas5086_dapm_sdin_texts), 563 SOC_ENUM_SINGLE(TAS5086_INPUT_MUX, 0, 8, tas5086_dapm_sdin_texts), 564 }; 565 566 static const struct snd_kcontrol_new tas5086_dapm_input_mux_controls[] = { 567 SOC_DAPM_ENUM("Channel 1 input", tas5086_dapm_input_mux_enum[0]), 568 SOC_DAPM_ENUM("Channel 2 input", tas5086_dapm_input_mux_enum[1]), 569 SOC_DAPM_ENUM("Channel 3 input", tas5086_dapm_input_mux_enum[2]), 570 SOC_DAPM_ENUM("Channel 4 input", tas5086_dapm_input_mux_enum[3]), 571 SOC_DAPM_ENUM("Channel 5 input", tas5086_dapm_input_mux_enum[4]), 572 SOC_DAPM_ENUM("Channel 6 input", tas5086_dapm_input_mux_enum[5]), 573 }; 574 575 /* Output mux controls */ 576 static const char *tas5086_dapm_channel_texts[] = 577 { "Channel 1 Mux", "Channel 2 Mux", "Channel 3 Mux", 578 "Channel 4 Mux", "Channel 5 Mux", "Channel 6 Mux" }; 579 580 static const struct soc_enum tas5086_dapm_output_mux_enum[] = { 581 SOC_ENUM_SINGLE(TAS5086_PWM_OUTPUT_MUX, 20, 6, tas5086_dapm_channel_texts), 582 SOC_ENUM_SINGLE(TAS5086_PWM_OUTPUT_MUX, 16, 6, tas5086_dapm_channel_texts), 583 SOC_ENUM_SINGLE(TAS5086_PWM_OUTPUT_MUX, 12, 6, tas5086_dapm_channel_texts), 584 SOC_ENUM_SINGLE(TAS5086_PWM_OUTPUT_MUX, 8, 6, tas5086_dapm_channel_texts), 585 SOC_ENUM_SINGLE(TAS5086_PWM_OUTPUT_MUX, 4, 6, tas5086_dapm_channel_texts), 586 SOC_ENUM_SINGLE(TAS5086_PWM_OUTPUT_MUX, 0, 6, tas5086_dapm_channel_texts), 587 }; 588 589 static const struct snd_kcontrol_new tas5086_dapm_output_mux_controls[] = { 590 SOC_DAPM_ENUM("PWM1 Output", tas5086_dapm_output_mux_enum[0]), 591 SOC_DAPM_ENUM("PWM2 Output", tas5086_dapm_output_mux_enum[1]), 592 SOC_DAPM_ENUM("PWM3 Output", tas5086_dapm_output_mux_enum[2]), 593 SOC_DAPM_ENUM("PWM4 Output", tas5086_dapm_output_mux_enum[3]), 594 SOC_DAPM_ENUM("PWM5 Output", tas5086_dapm_output_mux_enum[4]), 595 SOC_DAPM_ENUM("PWM6 Output", tas5086_dapm_output_mux_enum[5]), 596 }; 597 598 static const struct snd_soc_dapm_widget tas5086_dapm_widgets[] = { 599 SND_SOC_DAPM_INPUT("SDIN1-L"), 600 SND_SOC_DAPM_INPUT("SDIN1-R"), 601 SND_SOC_DAPM_INPUT("SDIN2-L"), 602 SND_SOC_DAPM_INPUT("SDIN2-R"), 603 SND_SOC_DAPM_INPUT("SDIN3-L"), 604 SND_SOC_DAPM_INPUT("SDIN3-R"), 605 SND_SOC_DAPM_INPUT("SDIN4-L"), 606 SND_SOC_DAPM_INPUT("SDIN4-R"), 607 608 SND_SOC_DAPM_OUTPUT("PWM1"), 609 SND_SOC_DAPM_OUTPUT("PWM2"), 610 SND_SOC_DAPM_OUTPUT("PWM3"), 611 SND_SOC_DAPM_OUTPUT("PWM4"), 612 SND_SOC_DAPM_OUTPUT("PWM5"), 613 SND_SOC_DAPM_OUTPUT("PWM6"), 614 615 SND_SOC_DAPM_MUX("Channel 1 Mux", SND_SOC_NOPM, 0, 0, 616 &tas5086_dapm_input_mux_controls[0]), 617 SND_SOC_DAPM_MUX("Channel 2 Mux", SND_SOC_NOPM, 0, 0, 618 &tas5086_dapm_input_mux_controls[1]), 619 SND_SOC_DAPM_MUX("Channel 3 Mux", SND_SOC_NOPM, 0, 0, 620 &tas5086_dapm_input_mux_controls[2]), 621 SND_SOC_DAPM_MUX("Channel 4 Mux", SND_SOC_NOPM, 0, 0, 622 &tas5086_dapm_input_mux_controls[3]), 623 SND_SOC_DAPM_MUX("Channel 5 Mux", SND_SOC_NOPM, 0, 0, 624 &tas5086_dapm_input_mux_controls[4]), 625 SND_SOC_DAPM_MUX("Channel 6 Mux", SND_SOC_NOPM, 0, 0, 626 &tas5086_dapm_input_mux_controls[5]), 627 628 SND_SOC_DAPM_MUX("PWM1 Mux", SND_SOC_NOPM, 0, 0, 629 &tas5086_dapm_output_mux_controls[0]), 630 SND_SOC_DAPM_MUX("PWM2 Mux", SND_SOC_NOPM, 0, 0, 631 &tas5086_dapm_output_mux_controls[1]), 632 SND_SOC_DAPM_MUX("PWM3 Mux", SND_SOC_NOPM, 0, 0, 633 &tas5086_dapm_output_mux_controls[2]), 634 SND_SOC_DAPM_MUX("PWM4 Mux", SND_SOC_NOPM, 0, 0, 635 &tas5086_dapm_output_mux_controls[3]), 636 SND_SOC_DAPM_MUX("PWM5 Mux", SND_SOC_NOPM, 0, 0, 637 &tas5086_dapm_output_mux_controls[4]), 638 SND_SOC_DAPM_MUX("PWM6 Mux", SND_SOC_NOPM, 0, 0, 639 &tas5086_dapm_output_mux_controls[5]), 640 }; 641 642 static const struct snd_soc_dapm_route tas5086_dapm_routes[] = { 643 /* SDIN inputs -> channel muxes */ 644 { "Channel 1 Mux", "SDIN1-L", "SDIN1-L" }, 645 { "Channel 1 Mux", "SDIN1-R", "SDIN1-R" }, 646 { "Channel 1 Mux", "SDIN2-L", "SDIN2-L" }, 647 { "Channel 1 Mux", "SDIN2-R", "SDIN2-R" }, 648 { "Channel 1 Mux", "SDIN3-L", "SDIN3-L" }, 649 { "Channel 1 Mux", "SDIN3-R", "SDIN3-R" }, 650 651 { "Channel 2 Mux", "SDIN1-L", "SDIN1-L" }, 652 { "Channel 2 Mux", "SDIN1-R", "SDIN1-R" }, 653 { "Channel 2 Mux", "SDIN2-L", "SDIN2-L" }, 654 { "Channel 2 Mux", "SDIN2-R", "SDIN2-R" }, 655 { "Channel 2 Mux", "SDIN3-L", "SDIN3-L" }, 656 { "Channel 2 Mux", "SDIN3-R", "SDIN3-R" }, 657 658 { "Channel 2 Mux", "SDIN1-L", "SDIN1-L" }, 659 { "Channel 2 Mux", "SDIN1-R", "SDIN1-R" }, 660 { "Channel 2 Mux", "SDIN2-L", "SDIN2-L" }, 661 { "Channel 2 Mux", "SDIN2-R", "SDIN2-R" }, 662 { "Channel 2 Mux", "SDIN3-L", "SDIN3-L" }, 663 { "Channel 2 Mux", "SDIN3-R", "SDIN3-R" }, 664 665 { "Channel 3 Mux", "SDIN1-L", "SDIN1-L" }, 666 { "Channel 3 Mux", "SDIN1-R", "SDIN1-R" }, 667 { "Channel 3 Mux", "SDIN2-L", "SDIN2-L" }, 668 { "Channel 3 Mux", "SDIN2-R", "SDIN2-R" }, 669 { "Channel 3 Mux", "SDIN3-L", "SDIN3-L" }, 670 { "Channel 3 Mux", "SDIN3-R", "SDIN3-R" }, 671 672 { "Channel 4 Mux", "SDIN1-L", "SDIN1-L" }, 673 { "Channel 4 Mux", "SDIN1-R", "SDIN1-R" }, 674 { "Channel 4 Mux", "SDIN2-L", "SDIN2-L" }, 675 { "Channel 4 Mux", "SDIN2-R", "SDIN2-R" }, 676 { "Channel 4 Mux", "SDIN3-L", "SDIN3-L" }, 677 { "Channel 4 Mux", "SDIN3-R", "SDIN3-R" }, 678 679 { "Channel 5 Mux", "SDIN1-L", "SDIN1-L" }, 680 { "Channel 5 Mux", "SDIN1-R", "SDIN1-R" }, 681 { "Channel 5 Mux", "SDIN2-L", "SDIN2-L" }, 682 { "Channel 5 Mux", "SDIN2-R", "SDIN2-R" }, 683 { "Channel 5 Mux", "SDIN3-L", "SDIN3-L" }, 684 { "Channel 5 Mux", "SDIN3-R", "SDIN3-R" }, 685 686 { "Channel 6 Mux", "SDIN1-L", "SDIN1-L" }, 687 { "Channel 6 Mux", "SDIN1-R", "SDIN1-R" }, 688 { "Channel 6 Mux", "SDIN2-L", "SDIN2-L" }, 689 { "Channel 6 Mux", "SDIN2-R", "SDIN2-R" }, 690 { "Channel 6 Mux", "SDIN3-L", "SDIN3-L" }, 691 { "Channel 6 Mux", "SDIN3-R", "SDIN3-R" }, 692 693 /* Channel muxes -> PWM muxes */ 694 { "PWM1 Mux", "Channel 1 Mux", "Channel 1 Mux" }, 695 { "PWM2 Mux", "Channel 1 Mux", "Channel 1 Mux" }, 696 { "PWM3 Mux", "Channel 1 Mux", "Channel 1 Mux" }, 697 { "PWM4 Mux", "Channel 1 Mux", "Channel 1 Mux" }, 698 { "PWM5 Mux", "Channel 1 Mux", "Channel 1 Mux" }, 699 { "PWM6 Mux", "Channel 1 Mux", "Channel 1 Mux" }, 700 701 { "PWM1 Mux", "Channel 2 Mux", "Channel 2 Mux" }, 702 { "PWM2 Mux", "Channel 2 Mux", "Channel 2 Mux" }, 703 { "PWM3 Mux", "Channel 2 Mux", "Channel 2 Mux" }, 704 { "PWM4 Mux", "Channel 2 Mux", "Channel 2 Mux" }, 705 { "PWM5 Mux", "Channel 2 Mux", "Channel 2 Mux" }, 706 { "PWM6 Mux", "Channel 2 Mux", "Channel 2 Mux" }, 707 708 { "PWM1 Mux", "Channel 3 Mux", "Channel 3 Mux" }, 709 { "PWM2 Mux", "Channel 3 Mux", "Channel 3 Mux" }, 710 { "PWM3 Mux", "Channel 3 Mux", "Channel 3 Mux" }, 711 { "PWM4 Mux", "Channel 3 Mux", "Channel 3 Mux" }, 712 { "PWM5 Mux", "Channel 3 Mux", "Channel 3 Mux" }, 713 { "PWM6 Mux", "Channel 3 Mux", "Channel 3 Mux" }, 714 715 { "PWM1 Mux", "Channel 4 Mux", "Channel 4 Mux" }, 716 { "PWM2 Mux", "Channel 4 Mux", "Channel 4 Mux" }, 717 { "PWM3 Mux", "Channel 4 Mux", "Channel 4 Mux" }, 718 { "PWM4 Mux", "Channel 4 Mux", "Channel 4 Mux" }, 719 { "PWM5 Mux", "Channel 4 Mux", "Channel 4 Mux" }, 720 { "PWM6 Mux", "Channel 4 Mux", "Channel 4 Mux" }, 721 722 { "PWM1 Mux", "Channel 5 Mux", "Channel 5 Mux" }, 723 { "PWM2 Mux", "Channel 5 Mux", "Channel 5 Mux" }, 724 { "PWM3 Mux", "Channel 5 Mux", "Channel 5 Mux" }, 725 { "PWM4 Mux", "Channel 5 Mux", "Channel 5 Mux" }, 726 { "PWM5 Mux", "Channel 5 Mux", "Channel 5 Mux" }, 727 { "PWM6 Mux", "Channel 5 Mux", "Channel 5 Mux" }, 728 729 { "PWM1 Mux", "Channel 6 Mux", "Channel 6 Mux" }, 730 { "PWM2 Mux", "Channel 6 Mux", "Channel 6 Mux" }, 731 { "PWM3 Mux", "Channel 6 Mux", "Channel 6 Mux" }, 732 { "PWM4 Mux", "Channel 6 Mux", "Channel 6 Mux" }, 733 { "PWM5 Mux", "Channel 6 Mux", "Channel 6 Mux" }, 734 { "PWM6 Mux", "Channel 6 Mux", "Channel 6 Mux" }, 735 736 /* The PWM muxes are directly connected to the PWM outputs */ 737 { "PWM1", NULL, "PWM1 Mux" }, 738 { "PWM2", NULL, "PWM2 Mux" }, 739 { "PWM3", NULL, "PWM3 Mux" }, 740 { "PWM4", NULL, "PWM4 Mux" }, 741 { "PWM5", NULL, "PWM5 Mux" }, 742 { "PWM6", NULL, "PWM6 Mux" }, 743 744 }; 745 746 static const struct snd_soc_dai_ops tas5086_dai_ops = { 747 .hw_params = tas5086_hw_params, 748 .set_sysclk = tas5086_set_dai_sysclk, 749 .set_fmt = tas5086_set_dai_fmt, 750 .mute_stream = tas5086_mute_stream, 751 }; 752 753 static struct snd_soc_dai_driver tas5086_dai = { 754 .name = "tas5086-hifi", 755 .playback = { 756 .stream_name = "Playback", 757 .channels_min = 2, 758 .channels_max = 6, 759 .rates = TAS5086_PCM_RATES, 760 .formats = TAS5086_PCM_FORMATS, 761 }, 762 .ops = &tas5086_dai_ops, 763 }; 764 765 #ifdef CONFIG_PM 766 static int tas5086_soc_suspend(struct snd_soc_component *component) 767 { 768 struct tas5086_private *priv = snd_soc_component_get_drvdata(component); 769 int ret; 770 771 /* Shut down all channels */ 772 ret = regmap_write(priv->regmap, TAS5086_SYS_CONTROL_2, 0x60); 773 if (ret < 0) 774 return ret; 775 776 regulator_bulk_disable(ARRAY_SIZE(priv->supplies), priv->supplies); 777 778 return 0; 779 } 780 781 static int tas5086_soc_resume(struct snd_soc_component *component) 782 { 783 struct tas5086_private *priv = snd_soc_component_get_drvdata(component); 784 int ret; 785 786 ret = regulator_bulk_enable(ARRAY_SIZE(priv->supplies), priv->supplies); 787 if (ret < 0) 788 return ret; 789 790 tas5086_reset(priv); 791 regcache_mark_dirty(priv->regmap); 792 793 ret = tas5086_init(component->dev, priv); 794 if (ret < 0) 795 return ret; 796 797 ret = regcache_sync(priv->regmap); 798 if (ret < 0) 799 return ret; 800 801 return 0; 802 } 803 #else 804 #define tas5086_soc_suspend NULL 805 #define tas5086_soc_resume NULL 806 #endif /* CONFIG_PM */ 807 808 #ifdef CONFIG_OF 809 static const struct of_device_id tas5086_dt_ids[] = { 810 { .compatible = "ti,tas5086", }, 811 { } 812 }; 813 MODULE_DEVICE_TABLE(of, tas5086_dt_ids); 814 #endif 815 816 static int tas5086_probe(struct snd_soc_component *component) 817 { 818 struct tas5086_private *priv = snd_soc_component_get_drvdata(component); 819 int i, ret; 820 821 ret = regulator_bulk_enable(ARRAY_SIZE(priv->supplies), priv->supplies); 822 if (ret < 0) { 823 dev_err(component->dev, "Failed to enable regulators: %d\n", ret); 824 return ret; 825 } 826 827 priv->pwm_start_mid_z = 0; 828 priv->charge_period = 1300000; /* hardware default is 1300 ms */ 829 830 if (of_match_device(of_match_ptr(tas5086_dt_ids), component->dev)) { 831 struct device_node *of_node = component->dev->of_node; 832 833 of_property_read_u32(of_node, "ti,charge-period", 834 &priv->charge_period); 835 836 for (i = 0; i < 6; i++) { 837 char name[25]; 838 839 snprintf(name, sizeof(name), 840 "ti,mid-z-channel-%d", i + 1); 841 842 if (of_property_read_bool(of_node, name)) 843 priv->pwm_start_mid_z |= 1 << i; 844 } 845 } 846 847 tas5086_reset(priv); 848 ret = tas5086_init(component->dev, priv); 849 if (ret < 0) 850 goto exit_disable_regulators; 851 852 /* set master volume to 0 dB */ 853 ret = regmap_write(priv->regmap, TAS5086_MASTER_VOL, 0x30); 854 if (ret < 0) 855 goto exit_disable_regulators; 856 857 return 0; 858 859 exit_disable_regulators: 860 regulator_bulk_disable(ARRAY_SIZE(priv->supplies), priv->supplies); 861 862 return ret; 863 } 864 865 static void tas5086_remove(struct snd_soc_component *component) 866 { 867 struct tas5086_private *priv = snd_soc_component_get_drvdata(component); 868 869 if (priv->reset) 870 /* Set codec to the reset state */ 871 gpiod_set_value(priv->reset, 1); 872 873 regulator_bulk_disable(ARRAY_SIZE(priv->supplies), priv->supplies); 874 }; 875 876 static const struct snd_soc_component_driver soc_component_dev_tas5086 = { 877 .probe = tas5086_probe, 878 .remove = tas5086_remove, 879 .suspend = tas5086_soc_suspend, 880 .resume = tas5086_soc_resume, 881 .controls = tas5086_controls, 882 .num_controls = ARRAY_SIZE(tas5086_controls), 883 .dapm_widgets = tas5086_dapm_widgets, 884 .num_dapm_widgets = ARRAY_SIZE(tas5086_dapm_widgets), 885 .dapm_routes = tas5086_dapm_routes, 886 .num_dapm_routes = ARRAY_SIZE(tas5086_dapm_routes), 887 .idle_bias_on = 1, 888 .use_pmdown_time = 1, 889 .endianness = 1, 890 }; 891 892 static const struct i2c_device_id tas5086_i2c_id[] = { 893 { "tas5086" }, 894 { } 895 }; 896 MODULE_DEVICE_TABLE(i2c, tas5086_i2c_id); 897 898 static const struct regmap_config tas5086_regmap = { 899 .reg_bits = 8, 900 .val_bits = 32, 901 .max_register = TAS5086_MAX_REGISTER, 902 .reg_defaults = tas5086_reg_defaults, 903 .num_reg_defaults = ARRAY_SIZE(tas5086_reg_defaults), 904 .cache_type = REGCACHE_RBTREE, 905 .volatile_reg = tas5086_volatile_reg, 906 .writeable_reg = tas5086_writeable_reg, 907 .readable_reg = tas5086_accessible_reg, 908 .reg_read = tas5086_reg_read, 909 .reg_write = tas5086_reg_write, 910 }; 911 912 static int tas5086_i2c_probe(struct i2c_client *i2c) 913 { 914 struct tas5086_private *priv; 915 struct device *dev = &i2c->dev; 916 int i, ret; 917 918 priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL); 919 if (!priv) 920 return -ENOMEM; 921 922 for (i = 0; i < ARRAY_SIZE(supply_names); i++) 923 priv->supplies[i].supply = supply_names[i]; 924 925 ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(priv->supplies), 926 priv->supplies); 927 if (ret < 0) { 928 dev_err(dev, "Failed to get regulators: %d\n", ret); 929 return ret; 930 } 931 932 priv->regmap = devm_regmap_init(dev, NULL, i2c, &tas5086_regmap); 933 if (IS_ERR(priv->regmap)) { 934 ret = PTR_ERR(priv->regmap); 935 dev_err(&i2c->dev, "Failed to create regmap: %d\n", ret); 936 return ret; 937 } 938 939 i2c_set_clientdata(i2c, priv); 940 941 /* Request line asserted */ 942 priv->reset = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_HIGH); 943 if (IS_ERR(priv->reset)) 944 return PTR_ERR(priv->reset); 945 gpiod_set_consumer_name(priv->reset, "TAS5086 Reset"); 946 947 ret = regulator_bulk_enable(ARRAY_SIZE(priv->supplies), priv->supplies); 948 if (ret < 0) { 949 dev_err(dev, "Failed to enable regulators: %d\n", ret); 950 return ret; 951 } 952 953 tas5086_reset(priv); 954 955 /* The TAS5086 always returns 0x03 in its TAS5086_DEV_ID register */ 956 ret = regmap_read(priv->regmap, TAS5086_DEV_ID, &i); 957 if (ret == 0 && i != 0x3) { 958 dev_err(dev, 959 "Failed to identify TAS5086 codec (got %02x)\n", i); 960 ret = -ENODEV; 961 } 962 963 /* 964 * The chip has been identified, so we can turn off the power 965 * again until the dai link is set up. 966 */ 967 regulator_bulk_disable(ARRAY_SIZE(priv->supplies), priv->supplies); 968 969 if (ret == 0) 970 ret = devm_snd_soc_register_component(&i2c->dev, 971 &soc_component_dev_tas5086, 972 &tas5086_dai, 1); 973 974 return ret; 975 } 976 977 static void tas5086_i2c_remove(struct i2c_client *i2c) 978 {} 979 980 static struct i2c_driver tas5086_i2c_driver = { 981 .driver = { 982 .name = "tas5086", 983 .of_match_table = of_match_ptr(tas5086_dt_ids), 984 }, 985 .id_table = tas5086_i2c_id, 986 .probe = tas5086_i2c_probe, 987 .remove = tas5086_i2c_remove, 988 }; 989 990 module_i2c_driver(tas5086_i2c_driver); 991 992 MODULE_AUTHOR("Daniel Mack <zonque@gmail.com>"); 993 MODULE_DESCRIPTION("Texas Instruments TAS5086 ALSA SoC Codec Driver"); 994 MODULE_LICENSE("GPL"); 995