1 /* 2 * CS4270 ALSA SoC (ASoC) codec driver 3 * 4 * Author: Timur Tabi <timur@freescale.com> 5 * 6 * Copyright 2007-2009 Freescale Semiconductor, Inc. This file is licensed 7 * under the terms of the GNU General Public License version 2. This 8 * program is licensed "as is" without any warranty of any kind, whether 9 * express or implied. 10 * 11 * This is an ASoC device driver for the Cirrus Logic CS4270 codec. 12 * 13 * Current features/limitations: 14 * 15 * - Software mode is supported. Stand-alone mode is not supported. 16 * - Only I2C is supported, not SPI 17 * - Support for master and slave mode 18 * - The machine driver's 'startup' function must call 19 * cs4270_set_dai_sysclk() with the value of MCLK. 20 * - Only I2S and left-justified modes are supported 21 * - Power management is supported 22 */ 23 24 #include <linux/module.h> 25 #include <linux/slab.h> 26 #include <sound/core.h> 27 #include <sound/soc.h> 28 #include <sound/initval.h> 29 #include <linux/i2c.h> 30 #include <linux/delay.h> 31 #include <linux/regulator/consumer.h> 32 #include <linux/gpio/consumer.h> 33 #include <linux/of_device.h> 34 35 /* 36 * The codec isn't really big-endian or little-endian, since the I2S 37 * interface requires data to be sent serially with the MSbit first. 38 * However, to support BE and LE I2S devices, we specify both here. That 39 * way, ALSA will always match the bit patterns. 40 */ 41 #define CS4270_FORMATS (SNDRV_PCM_FMTBIT_S8 | \ 42 SNDRV_PCM_FMTBIT_S16_LE | SNDRV_PCM_FMTBIT_S16_BE | \ 43 SNDRV_PCM_FMTBIT_S18_3LE | SNDRV_PCM_FMTBIT_S18_3BE | \ 44 SNDRV_PCM_FMTBIT_S20_3LE | SNDRV_PCM_FMTBIT_S20_3BE | \ 45 SNDRV_PCM_FMTBIT_S24_3LE | SNDRV_PCM_FMTBIT_S24_3BE | \ 46 SNDRV_PCM_FMTBIT_S24_LE | SNDRV_PCM_FMTBIT_S24_BE) 47 48 /* CS4270 registers addresses */ 49 #define CS4270_CHIPID 0x01 /* Chip ID */ 50 #define CS4270_PWRCTL 0x02 /* Power Control */ 51 #define CS4270_MODE 0x03 /* Mode Control */ 52 #define CS4270_FORMAT 0x04 /* Serial Format, ADC/DAC Control */ 53 #define CS4270_TRANS 0x05 /* Transition Control */ 54 #define CS4270_MUTE 0x06 /* Mute Control */ 55 #define CS4270_VOLA 0x07 /* DAC Channel A Volume Control */ 56 #define CS4270_VOLB 0x08 /* DAC Channel B Volume Control */ 57 58 #define CS4270_FIRSTREG 0x01 59 #define CS4270_LASTREG 0x08 60 #define CS4270_NUMREGS (CS4270_LASTREG - CS4270_FIRSTREG + 1) 61 #define CS4270_I2C_INCR 0x80 62 63 /* Bit masks for the CS4270 registers */ 64 #define CS4270_CHIPID_ID 0xF0 65 #define CS4270_CHIPID_REV 0x0F 66 #define CS4270_PWRCTL_FREEZE 0x80 67 #define CS4270_PWRCTL_PDN_ADC 0x20 68 #define CS4270_PWRCTL_PDN_DAC 0x02 69 #define CS4270_PWRCTL_PDN 0x01 70 #define CS4270_PWRCTL_PDN_ALL \ 71 (CS4270_PWRCTL_PDN_ADC | CS4270_PWRCTL_PDN_DAC | CS4270_PWRCTL_PDN) 72 #define CS4270_MODE_SPEED_MASK 0x30 73 #define CS4270_MODE_1X 0x00 74 #define CS4270_MODE_2X 0x10 75 #define CS4270_MODE_4X 0x20 76 #define CS4270_MODE_SLAVE 0x30 77 #define CS4270_MODE_DIV_MASK 0x0E 78 #define CS4270_MODE_DIV1 0x00 79 #define CS4270_MODE_DIV15 0x02 80 #define CS4270_MODE_DIV2 0x04 81 #define CS4270_MODE_DIV3 0x06 82 #define CS4270_MODE_DIV4 0x08 83 #define CS4270_MODE_POPGUARD 0x01 84 #define CS4270_FORMAT_FREEZE_A 0x80 85 #define CS4270_FORMAT_FREEZE_B 0x40 86 #define CS4270_FORMAT_LOOPBACK 0x20 87 #define CS4270_FORMAT_DAC_MASK 0x18 88 #define CS4270_FORMAT_DAC_LJ 0x00 89 #define CS4270_FORMAT_DAC_I2S 0x08 90 #define CS4270_FORMAT_DAC_RJ16 0x18 91 #define CS4270_FORMAT_DAC_RJ24 0x10 92 #define CS4270_FORMAT_ADC_MASK 0x01 93 #define CS4270_FORMAT_ADC_LJ 0x00 94 #define CS4270_FORMAT_ADC_I2S 0x01 95 #define CS4270_TRANS_ONE_VOL 0x80 96 #define CS4270_TRANS_SOFT 0x40 97 #define CS4270_TRANS_ZERO 0x20 98 #define CS4270_TRANS_INV_ADC_A 0x08 99 #define CS4270_TRANS_INV_ADC_B 0x10 100 #define CS4270_TRANS_INV_DAC_A 0x02 101 #define CS4270_TRANS_INV_DAC_B 0x04 102 #define CS4270_TRANS_DEEMPH 0x01 103 #define CS4270_MUTE_AUTO 0x20 104 #define CS4270_MUTE_ADC_A 0x08 105 #define CS4270_MUTE_ADC_B 0x10 106 #define CS4270_MUTE_POLARITY 0x04 107 #define CS4270_MUTE_DAC_A 0x01 108 #define CS4270_MUTE_DAC_B 0x02 109 110 /* Power-on default values for the registers 111 * 112 * This array contains the power-on default values of the registers, with the 113 * exception of the "CHIPID" register (01h). The lower four bits of that 114 * register contain the hardware revision, so it is treated as volatile. 115 */ 116 static const struct reg_default cs4270_reg_defaults[] = { 117 { 2, 0x00 }, 118 { 3, 0x30 }, 119 { 4, 0x00 }, 120 { 5, 0x60 }, 121 { 6, 0x20 }, 122 { 7, 0x00 }, 123 { 8, 0x00 }, 124 }; 125 126 static const char *supply_names[] = { 127 "va", "vd", "vlc" 128 }; 129 130 /* Private data for the CS4270 */ 131 struct cs4270_private { 132 struct regmap *regmap; 133 unsigned int mclk; /* Input frequency of the MCLK pin */ 134 unsigned int mode; /* The mode (I2S or left-justified) */ 135 unsigned int slave_mode; 136 unsigned int manual_mute; 137 138 /* power domain regulators */ 139 struct regulator_bulk_data supplies[ARRAY_SIZE(supply_names)]; 140 }; 141 142 static const struct snd_soc_dapm_widget cs4270_dapm_widgets[] = { 143 SND_SOC_DAPM_INPUT("AINL"), 144 SND_SOC_DAPM_INPUT("AINR"), 145 146 SND_SOC_DAPM_OUTPUT("AOUTL"), 147 SND_SOC_DAPM_OUTPUT("AOUTR"), 148 }; 149 150 static const struct snd_soc_dapm_route cs4270_dapm_routes[] = { 151 { "Capture", NULL, "AINL" }, 152 { "Capture", NULL, "AINR" }, 153 154 { "AOUTL", NULL, "Playback" }, 155 { "AOUTR", NULL, "Playback" }, 156 }; 157 158 /** 159 * struct cs4270_mode_ratios - clock ratio tables 160 * @ratio: the ratio of MCLK to the sample rate 161 * @speed_mode: the Speed Mode bits to set in the Mode Control register for 162 * this ratio 163 * @mclk: the Ratio Select bits to set in the Mode Control register for this 164 * ratio 165 * 166 * The data for this chart is taken from Table 5 of the CS4270 reference 167 * manual. 168 * 169 * This table is used to determine how to program the Mode Control register. 170 * It is also used by cs4270_set_dai_sysclk() to tell ALSA which sampling 171 * rates the CS4270 currently supports. 172 * 173 * @speed_mode is the corresponding bit pattern to be written to the 174 * MODE bits of the Mode Control Register 175 * 176 * @mclk is the corresponding bit pattern to be wirten to the MCLK bits of 177 * the Mode Control Register. 178 * 179 * In situations where a single ratio is represented by multiple speed 180 * modes, we favor the slowest speed. E.g, for a ratio of 128, we pick 181 * double-speed instead of quad-speed. However, the CS4270 errata states 182 * that divide-By-1.5 can cause failures, so we avoid that mode where 183 * possible. 184 * 185 * Errata: There is an errata for the CS4270 where divide-by-1.5 does not 186 * work if Vd is 3.3V. If this effects you, select the 187 * CONFIG_SND_SOC_CS4270_VD33_ERRATA Kconfig option, and the driver will 188 * never select any sample rates that require divide-by-1.5. 189 */ 190 struct cs4270_mode_ratios { 191 unsigned int ratio; 192 u8 speed_mode; 193 u8 mclk; 194 }; 195 196 static struct cs4270_mode_ratios cs4270_mode_ratios[] = { 197 {64, CS4270_MODE_4X, CS4270_MODE_DIV1}, 198 #ifndef CONFIG_SND_SOC_CS4270_VD33_ERRATA 199 {96, CS4270_MODE_4X, CS4270_MODE_DIV15}, 200 #endif 201 {128, CS4270_MODE_2X, CS4270_MODE_DIV1}, 202 {192, CS4270_MODE_4X, CS4270_MODE_DIV3}, 203 {256, CS4270_MODE_1X, CS4270_MODE_DIV1}, 204 {384, CS4270_MODE_2X, CS4270_MODE_DIV3}, 205 {512, CS4270_MODE_1X, CS4270_MODE_DIV2}, 206 {768, CS4270_MODE_1X, CS4270_MODE_DIV3}, 207 {1024, CS4270_MODE_1X, CS4270_MODE_DIV4} 208 }; 209 210 /* The number of MCLK/LRCK ratios supported by the CS4270 */ 211 #define NUM_MCLK_RATIOS ARRAY_SIZE(cs4270_mode_ratios) 212 213 static bool cs4270_reg_is_readable(struct device *dev, unsigned int reg) 214 { 215 return (reg >= CS4270_FIRSTREG) && (reg <= CS4270_LASTREG); 216 } 217 218 static bool cs4270_reg_is_volatile(struct device *dev, unsigned int reg) 219 { 220 /* Unreadable registers are considered volatile */ 221 if ((reg < CS4270_FIRSTREG) || (reg > CS4270_LASTREG)) 222 return true; 223 224 return reg == CS4270_CHIPID; 225 } 226 227 /** 228 * cs4270_set_dai_sysclk - determine the CS4270 samples rates. 229 * @codec_dai: the codec DAI 230 * @clk_id: the clock ID (ignored) 231 * @freq: the MCLK input frequency 232 * @dir: the clock direction (ignored) 233 * 234 * This function is used to tell the codec driver what the input MCLK 235 * frequency is. 236 * 237 * The value of MCLK is used to determine which sample rates are supported 238 * by the CS4270. The ratio of MCLK / Fs must be equal to one of nine 239 * supported values - 64, 96, 128, 192, 256, 384, 512, 768, and 1024. 240 * 241 * This function calculates the nine ratios and determines which ones match 242 * a standard sample rate. If there's a match, then it is added to the list 243 * of supported sample rates. 244 * 245 * This function must be called by the machine driver's 'startup' function, 246 * otherwise the list of supported sample rates will not be available in 247 * time for ALSA. 248 * 249 * For setups with variable MCLKs, pass 0 as 'freq' argument. This will cause 250 * theoretically possible sample rates to be enabled. Call it again with a 251 * proper value set one the external clock is set (most probably you would do 252 * that from a machine's driver 'hw_param' hook. 253 */ 254 static int cs4270_set_dai_sysclk(struct snd_soc_dai *codec_dai, 255 int clk_id, unsigned int freq, int dir) 256 { 257 struct snd_soc_component *component = codec_dai->component; 258 struct cs4270_private *cs4270 = snd_soc_component_get_drvdata(component); 259 260 cs4270->mclk = freq; 261 return 0; 262 } 263 264 /** 265 * cs4270_set_dai_fmt - configure the codec for the selected audio format 266 * @codec_dai: the codec DAI 267 * @format: a SND_SOC_DAIFMT_x value indicating the data format 268 * 269 * This function takes a bitmask of SND_SOC_DAIFMT_x bits and programs the 270 * codec accordingly. 271 * 272 * Currently, this function only supports SND_SOC_DAIFMT_I2S and 273 * SND_SOC_DAIFMT_LEFT_J. The CS4270 codec also supports right-justified 274 * data for playback only, but ASoC currently does not support different 275 * formats for playback vs. record. 276 */ 277 static int cs4270_set_dai_fmt(struct snd_soc_dai *codec_dai, 278 unsigned int format) 279 { 280 struct snd_soc_component *component = codec_dai->component; 281 struct cs4270_private *cs4270 = snd_soc_component_get_drvdata(component); 282 283 /* set DAI format */ 284 switch (format & SND_SOC_DAIFMT_FORMAT_MASK) { 285 case SND_SOC_DAIFMT_I2S: 286 case SND_SOC_DAIFMT_LEFT_J: 287 cs4270->mode = format & SND_SOC_DAIFMT_FORMAT_MASK; 288 break; 289 default: 290 dev_err(component->dev, "invalid dai format\n"); 291 return -EINVAL; 292 } 293 294 /* set master/slave audio interface */ 295 switch (format & SND_SOC_DAIFMT_MASTER_MASK) { 296 case SND_SOC_DAIFMT_CBS_CFS: 297 cs4270->slave_mode = 1; 298 break; 299 case SND_SOC_DAIFMT_CBM_CFM: 300 cs4270->slave_mode = 0; 301 break; 302 default: 303 /* all other modes are unsupported by the hardware */ 304 dev_err(component->dev, "Unknown master/slave configuration\n"); 305 return -EINVAL; 306 } 307 308 return 0; 309 } 310 311 /** 312 * cs4270_hw_params - program the CS4270 with the given hardware parameters. 313 * @substream: the audio stream 314 * @params: the hardware parameters to set 315 * @dai: the SOC DAI (ignored) 316 * 317 * This function programs the hardware with the values provided. 318 * Specifically, the sample rate and the data format. 319 * 320 * The .ops functions are used to provide board-specific data, like input 321 * frequencies, to this driver. This function takes that information, 322 * combines it with the hardware parameters provided, and programs the 323 * hardware accordingly. 324 */ 325 static int cs4270_hw_params(struct snd_pcm_substream *substream, 326 struct snd_pcm_hw_params *params, 327 struct snd_soc_dai *dai) 328 { 329 struct snd_soc_component *component = dai->component; 330 struct cs4270_private *cs4270 = snd_soc_component_get_drvdata(component); 331 int ret; 332 unsigned int i; 333 unsigned int rate; 334 unsigned int ratio; 335 int reg; 336 337 /* Figure out which MCLK/LRCK ratio to use */ 338 339 rate = params_rate(params); /* Sampling rate, in Hz */ 340 ratio = cs4270->mclk / rate; /* MCLK/LRCK ratio */ 341 342 for (i = 0; i < NUM_MCLK_RATIOS; i++) { 343 if (cs4270_mode_ratios[i].ratio == ratio) 344 break; 345 } 346 347 if (i == NUM_MCLK_RATIOS) { 348 /* We did not find a matching ratio */ 349 dev_err(component->dev, "could not find matching ratio\n"); 350 return -EINVAL; 351 } 352 353 /* Set the sample rate */ 354 355 reg = snd_soc_component_read32(component, CS4270_MODE); 356 reg &= ~(CS4270_MODE_SPEED_MASK | CS4270_MODE_DIV_MASK); 357 reg |= cs4270_mode_ratios[i].mclk; 358 359 if (cs4270->slave_mode) 360 reg |= CS4270_MODE_SLAVE; 361 else 362 reg |= cs4270_mode_ratios[i].speed_mode; 363 364 ret = snd_soc_component_write(component, CS4270_MODE, reg); 365 if (ret < 0) { 366 dev_err(component->dev, "i2c write failed\n"); 367 return ret; 368 } 369 370 /* Set the DAI format */ 371 372 reg = snd_soc_component_read32(component, CS4270_FORMAT); 373 reg &= ~(CS4270_FORMAT_DAC_MASK | CS4270_FORMAT_ADC_MASK); 374 375 switch (cs4270->mode) { 376 case SND_SOC_DAIFMT_I2S: 377 reg |= CS4270_FORMAT_DAC_I2S | CS4270_FORMAT_ADC_I2S; 378 break; 379 case SND_SOC_DAIFMT_LEFT_J: 380 reg |= CS4270_FORMAT_DAC_LJ | CS4270_FORMAT_ADC_LJ; 381 break; 382 default: 383 dev_err(component->dev, "unknown dai format\n"); 384 return -EINVAL; 385 } 386 387 ret = snd_soc_component_write(component, CS4270_FORMAT, reg); 388 if (ret < 0) { 389 dev_err(component->dev, "i2c write failed\n"); 390 return ret; 391 } 392 393 return ret; 394 } 395 396 /** 397 * cs4270_dai_mute - enable/disable the CS4270 external mute 398 * @dai: the SOC DAI 399 * @mute: 0 = disable mute, 1 = enable mute 400 * 401 * This function toggles the mute bits in the MUTE register. The CS4270's 402 * mute capability is intended for external muting circuitry, so if the 403 * board does not have the MUTEA or MUTEB pins connected to such circuitry, 404 * then this function will do nothing. 405 */ 406 static int cs4270_dai_mute(struct snd_soc_dai *dai, int mute) 407 { 408 struct snd_soc_component *component = dai->component; 409 struct cs4270_private *cs4270 = snd_soc_component_get_drvdata(component); 410 int reg6; 411 412 reg6 = snd_soc_component_read32(component, CS4270_MUTE); 413 414 if (mute) 415 reg6 |= CS4270_MUTE_DAC_A | CS4270_MUTE_DAC_B; 416 else { 417 reg6 &= ~(CS4270_MUTE_DAC_A | CS4270_MUTE_DAC_B); 418 reg6 |= cs4270->manual_mute; 419 } 420 421 return snd_soc_component_write(component, CS4270_MUTE, reg6); 422 } 423 424 /** 425 * cs4270_soc_put_mute - put callback for the 'Master Playback switch' 426 * alsa control. 427 * @kcontrol: mixer control 428 * @ucontrol: control element information 429 * 430 * This function basically passes the arguments on to the generic 431 * snd_soc_put_volsw() function and saves the mute information in 432 * our private data structure. This is because we want to prevent 433 * cs4270_dai_mute() neglecting the user's decision to manually 434 * mute the codec's output. 435 * 436 * Returns 0 for success. 437 */ 438 static int cs4270_soc_put_mute(struct snd_kcontrol *kcontrol, 439 struct snd_ctl_elem_value *ucontrol) 440 { 441 struct snd_soc_component *component = snd_soc_kcontrol_component(kcontrol); 442 struct cs4270_private *cs4270 = snd_soc_component_get_drvdata(component); 443 int left = !ucontrol->value.integer.value[0]; 444 int right = !ucontrol->value.integer.value[1]; 445 446 cs4270->manual_mute = (left ? CS4270_MUTE_DAC_A : 0) | 447 (right ? CS4270_MUTE_DAC_B : 0); 448 449 return snd_soc_put_volsw(kcontrol, ucontrol); 450 } 451 452 /* A list of non-DAPM controls that the CS4270 supports */ 453 static const struct snd_kcontrol_new cs4270_snd_controls[] = { 454 SOC_DOUBLE_R("Master Playback Volume", 455 CS4270_VOLA, CS4270_VOLB, 0, 0xFF, 1), 456 SOC_SINGLE("Digital Sidetone Switch", CS4270_FORMAT, 5, 1, 0), 457 SOC_SINGLE("Soft Ramp Switch", CS4270_TRANS, 6, 1, 0), 458 SOC_SINGLE("Zero Cross Switch", CS4270_TRANS, 5, 1, 0), 459 SOC_SINGLE("De-emphasis filter", CS4270_TRANS, 0, 1, 0), 460 SOC_SINGLE("Popguard Switch", CS4270_MODE, 0, 1, 1), 461 SOC_SINGLE("Auto-Mute Switch", CS4270_MUTE, 5, 1, 0), 462 SOC_DOUBLE("Master Capture Switch", CS4270_MUTE, 3, 4, 1, 1), 463 SOC_DOUBLE_EXT("Master Playback Switch", CS4270_MUTE, 0, 1, 1, 1, 464 snd_soc_get_volsw, cs4270_soc_put_mute), 465 }; 466 467 static const struct snd_soc_dai_ops cs4270_dai_ops = { 468 .hw_params = cs4270_hw_params, 469 .set_sysclk = cs4270_set_dai_sysclk, 470 .set_fmt = cs4270_set_dai_fmt, 471 .digital_mute = cs4270_dai_mute, 472 }; 473 474 static struct snd_soc_dai_driver cs4270_dai = { 475 .name = "cs4270-hifi", 476 .playback = { 477 .stream_name = "Playback", 478 .channels_min = 2, 479 .channels_max = 2, 480 .rates = SNDRV_PCM_RATE_CONTINUOUS, 481 .rate_min = 4000, 482 .rate_max = 216000, 483 .formats = CS4270_FORMATS, 484 }, 485 .capture = { 486 .stream_name = "Capture", 487 .channels_min = 2, 488 .channels_max = 2, 489 .rates = SNDRV_PCM_RATE_CONTINUOUS, 490 .rate_min = 4000, 491 .rate_max = 216000, 492 .formats = CS4270_FORMATS, 493 }, 494 .ops = &cs4270_dai_ops, 495 }; 496 497 /** 498 * cs4270_probe - ASoC probe function 499 * @pdev: platform device 500 * 501 * This function is called when ASoC has all the pieces it needs to 502 * instantiate a sound driver. 503 */ 504 static int cs4270_probe(struct snd_soc_component *component) 505 { 506 struct cs4270_private *cs4270 = snd_soc_component_get_drvdata(component); 507 int ret; 508 509 /* Disable auto-mute. This feature appears to be buggy. In some 510 * situations, auto-mute will not deactivate when it should, so we want 511 * this feature disabled by default. An application (e.g. alsactl) can 512 * re-enabled it by using the controls. 513 */ 514 ret = snd_soc_component_update_bits(component, CS4270_MUTE, CS4270_MUTE_AUTO, 0); 515 if (ret < 0) { 516 dev_err(component->dev, "i2c write failed\n"); 517 return ret; 518 } 519 520 /* Disable automatic volume control. The hardware enables, and it 521 * causes volume change commands to be delayed, sometimes until after 522 * playback has started. An application (e.g. alsactl) can 523 * re-enabled it by using the controls. 524 */ 525 ret = snd_soc_component_update_bits(component, CS4270_TRANS, 526 CS4270_TRANS_SOFT | CS4270_TRANS_ZERO, 0); 527 if (ret < 0) { 528 dev_err(component->dev, "i2c write failed\n"); 529 return ret; 530 } 531 532 ret = regulator_bulk_enable(ARRAY_SIZE(cs4270->supplies), 533 cs4270->supplies); 534 535 return ret; 536 } 537 538 /** 539 * cs4270_remove - ASoC remove function 540 * @pdev: platform device 541 * 542 * This function is the counterpart to cs4270_probe(). 543 */ 544 static void cs4270_remove(struct snd_soc_component *component) 545 { 546 struct cs4270_private *cs4270 = snd_soc_component_get_drvdata(component); 547 548 regulator_bulk_disable(ARRAY_SIZE(cs4270->supplies), cs4270->supplies); 549 }; 550 551 #ifdef CONFIG_PM 552 553 /* This suspend/resume implementation can handle both - a simple standby 554 * where the codec remains powered, and a full suspend, where the voltage 555 * domain the codec is connected to is teared down and/or any other hardware 556 * reset condition is asserted. 557 * 558 * The codec's own power saving features are enabled in the suspend callback, 559 * and all registers are written back to the hardware when resuming. 560 */ 561 562 static int cs4270_soc_suspend(struct snd_soc_component *component) 563 { 564 struct cs4270_private *cs4270 = snd_soc_component_get_drvdata(component); 565 int reg, ret; 566 567 reg = snd_soc_component_read32(component, CS4270_PWRCTL) | CS4270_PWRCTL_PDN_ALL; 568 if (reg < 0) 569 return reg; 570 571 ret = snd_soc_component_write(component, CS4270_PWRCTL, reg); 572 if (ret < 0) 573 return ret; 574 575 regulator_bulk_disable(ARRAY_SIZE(cs4270->supplies), 576 cs4270->supplies); 577 578 return 0; 579 } 580 581 static int cs4270_soc_resume(struct snd_soc_component *component) 582 { 583 struct cs4270_private *cs4270 = snd_soc_component_get_drvdata(component); 584 int reg, ret; 585 586 ret = regulator_bulk_enable(ARRAY_SIZE(cs4270->supplies), 587 cs4270->supplies); 588 if (ret != 0) 589 return ret; 590 591 /* In case the device was put to hard reset during sleep, we need to 592 * wait 500ns here before any I2C communication. */ 593 ndelay(500); 594 595 /* first restore the entire register cache ... */ 596 regcache_sync(cs4270->regmap); 597 598 /* ... then disable the power-down bits */ 599 reg = snd_soc_component_read32(component, CS4270_PWRCTL); 600 reg &= ~CS4270_PWRCTL_PDN_ALL; 601 602 return snd_soc_component_write(component, CS4270_PWRCTL, reg); 603 } 604 #else 605 #define cs4270_soc_suspend NULL 606 #define cs4270_soc_resume NULL 607 #endif /* CONFIG_PM */ 608 609 /* 610 * ASoC codec driver structure 611 */ 612 static const struct snd_soc_component_driver soc_component_device_cs4270 = { 613 .probe = cs4270_probe, 614 .remove = cs4270_remove, 615 .suspend = cs4270_soc_suspend, 616 .resume = cs4270_soc_resume, 617 .controls = cs4270_snd_controls, 618 .num_controls = ARRAY_SIZE(cs4270_snd_controls), 619 .dapm_widgets = cs4270_dapm_widgets, 620 .num_dapm_widgets = ARRAY_SIZE(cs4270_dapm_widgets), 621 .dapm_routes = cs4270_dapm_routes, 622 .num_dapm_routes = ARRAY_SIZE(cs4270_dapm_routes), 623 .idle_bias_on = 1, 624 .use_pmdown_time = 1, 625 .endianness = 1, 626 .non_legacy_dai_naming = 1, 627 }; 628 629 /* 630 * cs4270_of_match - the device tree bindings 631 */ 632 static const struct of_device_id cs4270_of_match[] = { 633 { .compatible = "cirrus,cs4270", }, 634 { } 635 }; 636 MODULE_DEVICE_TABLE(of, cs4270_of_match); 637 638 static const struct regmap_config cs4270_regmap = { 639 .reg_bits = 8, 640 .val_bits = 8, 641 .max_register = CS4270_LASTREG, 642 .reg_defaults = cs4270_reg_defaults, 643 .num_reg_defaults = ARRAY_SIZE(cs4270_reg_defaults), 644 .cache_type = REGCACHE_RBTREE, 645 .write_flag_mask = CS4270_I2C_INCR, 646 647 .readable_reg = cs4270_reg_is_readable, 648 .volatile_reg = cs4270_reg_is_volatile, 649 }; 650 651 /** 652 * cs4270_i2c_probe - initialize the I2C interface of the CS4270 653 * @i2c_client: the I2C client object 654 * @id: the I2C device ID (ignored) 655 * 656 * This function is called whenever the I2C subsystem finds a device that 657 * matches the device ID given via a prior call to i2c_add_driver(). 658 */ 659 static int cs4270_i2c_probe(struct i2c_client *i2c_client, 660 const struct i2c_device_id *id) 661 { 662 struct cs4270_private *cs4270; 663 struct gpio_desc *reset_gpiod; 664 unsigned int val; 665 int ret, i; 666 667 cs4270 = devm_kzalloc(&i2c_client->dev, sizeof(struct cs4270_private), 668 GFP_KERNEL); 669 if (!cs4270) 670 return -ENOMEM; 671 672 /* get the power supply regulators */ 673 for (i = 0; i < ARRAY_SIZE(supply_names); i++) 674 cs4270->supplies[i].supply = supply_names[i]; 675 676 ret = devm_regulator_bulk_get(&i2c_client->dev, 677 ARRAY_SIZE(cs4270->supplies), 678 cs4270->supplies); 679 if (ret < 0) 680 return ret; 681 682 reset_gpiod = devm_gpiod_get_optional(&i2c_client->dev, "reset", 683 GPIOD_OUT_HIGH); 684 if (IS_ERR(reset_gpiod) && 685 PTR_ERR(reset_gpiod) == -EPROBE_DEFER) 686 return -EPROBE_DEFER; 687 688 cs4270->regmap = devm_regmap_init_i2c(i2c_client, &cs4270_regmap); 689 if (IS_ERR(cs4270->regmap)) 690 return PTR_ERR(cs4270->regmap); 691 692 /* Verify that we have a CS4270 */ 693 ret = regmap_read(cs4270->regmap, CS4270_CHIPID, &val); 694 if (ret < 0) { 695 dev_err(&i2c_client->dev, "failed to read i2c at addr %X\n", 696 i2c_client->addr); 697 return ret; 698 } 699 /* The top four bits of the chip ID should be 1100. */ 700 if ((val & 0xF0) != 0xC0) { 701 dev_err(&i2c_client->dev, "device at addr %X is not a CS4270\n", 702 i2c_client->addr); 703 return -ENODEV; 704 } 705 706 dev_info(&i2c_client->dev, "found device at i2c address %X\n", 707 i2c_client->addr); 708 dev_info(&i2c_client->dev, "hardware revision %X\n", val & 0xF); 709 710 i2c_set_clientdata(i2c_client, cs4270); 711 712 ret = devm_snd_soc_register_component(&i2c_client->dev, 713 &soc_component_device_cs4270, &cs4270_dai, 1); 714 return ret; 715 } 716 717 /* 718 * cs4270_id - I2C device IDs supported by this driver 719 */ 720 static const struct i2c_device_id cs4270_id[] = { 721 {"cs4270", 0}, 722 {} 723 }; 724 MODULE_DEVICE_TABLE(i2c, cs4270_id); 725 726 /* 727 * cs4270_i2c_driver - I2C device identification 728 * 729 * This structure tells the I2C subsystem how to identify and support a 730 * given I2C device type. 731 */ 732 static struct i2c_driver cs4270_i2c_driver = { 733 .driver = { 734 .name = "cs4270", 735 .of_match_table = cs4270_of_match, 736 }, 737 .id_table = cs4270_id, 738 .probe = cs4270_i2c_probe, 739 }; 740 741 module_i2c_driver(cs4270_i2c_driver); 742 743 MODULE_AUTHOR("Timur Tabi <timur@freescale.com>"); 744 MODULE_DESCRIPTION("Cirrus Logic CS4270 ALSA SoC Codec Driver"); 745 MODULE_LICENSE("GPL"); 746