1 /*
2 * CS4270 ALSA SoC (ASoC) codec driver
3 *
4 * Author: Timur Tabi <timur@freescale.com>
5 *
6 * Copyright 2007-2009 Freescale Semiconductor, Inc. This file is licensed
7 * under the terms of the GNU General Public License version 2. This
8 * program is licensed "as is" without any warranty of any kind, whether
9 * express or implied.
10 *
11 * This is an ASoC device driver for the Cirrus Logic CS4270 codec.
12 *
13 * Current features/limitations:
14 *
15 * - Software mode is supported. Stand-alone mode is not supported.
16 * - Only I2C is supported, not SPI
17 * - Support for master and slave mode
18 * - The machine driver's 'startup' function must call
19 * cs4270_set_dai_sysclk() with the value of MCLK.
20 * - Only I2S and left-justified modes are supported
21 * - Power management is supported
22 */
23
24 #include <linux/mod_devicetable.h>
25 #include <linux/module.h>
26 #include <linux/slab.h>
27 #include <sound/core.h>
28 #include <sound/soc.h>
29 #include <sound/initval.h>
30 #include <linux/i2c.h>
31 #include <linux/delay.h>
32 #include <linux/regulator/consumer.h>
33 #include <linux/gpio/consumer.h>
34
35 #define CS4270_FORMATS (SNDRV_PCM_FMTBIT_S8 | SNDRV_PCM_FMTBIT_S16_LE | \
36 SNDRV_PCM_FMTBIT_S18_3LE | SNDRV_PCM_FMTBIT_S20_3LE | \
37 SNDRV_PCM_FMTBIT_S24_3LE | SNDRV_PCM_FMTBIT_S24_LE)
38
39 /* CS4270 registers addresses */
40 #define CS4270_CHIPID 0x01 /* Chip ID */
41 #define CS4270_PWRCTL 0x02 /* Power Control */
42 #define CS4270_MODE 0x03 /* Mode Control */
43 #define CS4270_FORMAT 0x04 /* Serial Format, ADC/DAC Control */
44 #define CS4270_TRANS 0x05 /* Transition Control */
45 #define CS4270_MUTE 0x06 /* Mute Control */
46 #define CS4270_VOLA 0x07 /* DAC Channel A Volume Control */
47 #define CS4270_VOLB 0x08 /* DAC Channel B Volume Control */
48
49 #define CS4270_FIRSTREG 0x01
50 #define CS4270_LASTREG 0x08
51 #define CS4270_NUMREGS (CS4270_LASTREG - CS4270_FIRSTREG + 1)
52 #define CS4270_I2C_INCR 0x80
53
54 /* Bit masks for the CS4270 registers */
55 #define CS4270_CHIPID_ID 0xF0
56 #define CS4270_CHIPID_REV 0x0F
57 #define CS4270_PWRCTL_FREEZE 0x80
58 #define CS4270_PWRCTL_PDN_ADC 0x20
59 #define CS4270_PWRCTL_PDN_DAC 0x02
60 #define CS4270_PWRCTL_PDN 0x01
61 #define CS4270_PWRCTL_PDN_ALL \
62 (CS4270_PWRCTL_PDN_ADC | CS4270_PWRCTL_PDN_DAC | CS4270_PWRCTL_PDN)
63 #define CS4270_MODE_SPEED_MASK 0x30
64 #define CS4270_MODE_1X 0x00
65 #define CS4270_MODE_2X 0x10
66 #define CS4270_MODE_4X 0x20
67 #define CS4270_MODE_SLAVE 0x30
68 #define CS4270_MODE_DIV_MASK 0x0E
69 #define CS4270_MODE_DIV1 0x00
70 #define CS4270_MODE_DIV15 0x02
71 #define CS4270_MODE_DIV2 0x04
72 #define CS4270_MODE_DIV3 0x06
73 #define CS4270_MODE_DIV4 0x08
74 #define CS4270_MODE_POPGUARD 0x01
75 #define CS4270_FORMAT_FREEZE_A 0x80
76 #define CS4270_FORMAT_FREEZE_B 0x40
77 #define CS4270_FORMAT_LOOPBACK 0x20
78 #define CS4270_FORMAT_DAC_MASK 0x18
79 #define CS4270_FORMAT_DAC_LJ 0x00
80 #define CS4270_FORMAT_DAC_I2S 0x08
81 #define CS4270_FORMAT_DAC_RJ16 0x18
82 #define CS4270_FORMAT_DAC_RJ24 0x10
83 #define CS4270_FORMAT_ADC_MASK 0x01
84 #define CS4270_FORMAT_ADC_LJ 0x00
85 #define CS4270_FORMAT_ADC_I2S 0x01
86 #define CS4270_TRANS_ONE_VOL 0x80
87 #define CS4270_TRANS_SOFT 0x40
88 #define CS4270_TRANS_ZERO 0x20
89 #define CS4270_TRANS_INV_ADC_A 0x08
90 #define CS4270_TRANS_INV_ADC_B 0x10
91 #define CS4270_TRANS_INV_DAC_A 0x02
92 #define CS4270_TRANS_INV_DAC_B 0x04
93 #define CS4270_TRANS_DEEMPH 0x01
94 #define CS4270_MUTE_AUTO 0x20
95 #define CS4270_MUTE_ADC_A 0x08
96 #define CS4270_MUTE_ADC_B 0x10
97 #define CS4270_MUTE_POLARITY 0x04
98 #define CS4270_MUTE_DAC_A 0x01
99 #define CS4270_MUTE_DAC_B 0x02
100
101 /* Power-on default values for the registers
102 *
103 * This array contains the power-on default values of the registers, with the
104 * exception of the "CHIPID" register (01h). The lower four bits of that
105 * register contain the hardware revision, so it is treated as volatile.
106 */
107 static const struct reg_default cs4270_reg_defaults[] = {
108 { 2, 0x00 },
109 { 3, 0x30 },
110 { 4, 0x00 },
111 { 5, 0x60 },
112 { 6, 0x20 },
113 { 7, 0x00 },
114 { 8, 0x00 },
115 };
116
117 static const char *supply_names[] = {
118 "va", "vd", "vlc"
119 };
120
121 /* Private data for the CS4270 */
122 struct cs4270_private {
123 struct regmap *regmap;
124 unsigned int mclk; /* Input frequency of the MCLK pin */
125 unsigned int mode; /* The mode (I2S or left-justified) */
126 unsigned int slave_mode;
127 unsigned int manual_mute;
128
129 /* power domain regulators */
130 struct regulator_bulk_data supplies[ARRAY_SIZE(supply_names)];
131
132 /* reset gpio */
133 struct gpio_desc *reset_gpio;
134 };
135
136 static const struct snd_soc_dapm_widget cs4270_dapm_widgets[] = {
137 SND_SOC_DAPM_INPUT("AINL"),
138 SND_SOC_DAPM_INPUT("AINR"),
139
140 SND_SOC_DAPM_OUTPUT("AOUTL"),
141 SND_SOC_DAPM_OUTPUT("AOUTR"),
142 };
143
144 static const struct snd_soc_dapm_route cs4270_dapm_routes[] = {
145 { "Capture", NULL, "AINL" },
146 { "Capture", NULL, "AINR" },
147
148 { "AOUTL", NULL, "Playback" },
149 { "AOUTR", NULL, "Playback" },
150 };
151
152 /**
153 * struct cs4270_mode_ratios - clock ratio tables
154 * @ratio: the ratio of MCLK to the sample rate
155 * @speed_mode: the Speed Mode bits to set in the Mode Control register for
156 * this ratio
157 * @mclk: the Ratio Select bits to set in the Mode Control register for this
158 * ratio
159 *
160 * The data for this chart is taken from Table 5 of the CS4270 reference
161 * manual.
162 *
163 * This table is used to determine how to program the Mode Control register.
164 * It is also used by cs4270_set_dai_sysclk() to tell ALSA which sampling
165 * rates the CS4270 currently supports.
166 *
167 * @speed_mode is the corresponding bit pattern to be written to the
168 * MODE bits of the Mode Control Register
169 *
170 * @mclk is the corresponding bit pattern to be wirten to the MCLK bits of
171 * the Mode Control Register.
172 *
173 * In situations where a single ratio is represented by multiple speed
174 * modes, we favor the slowest speed. E.g, for a ratio of 128, we pick
175 * double-speed instead of quad-speed. However, the CS4270 errata states
176 * that divide-By-1.5 can cause failures, so we avoid that mode where
177 * possible.
178 *
179 * Errata: There is an errata for the CS4270 where divide-by-1.5 does not
180 * work if Vd is 3.3V. If this effects you, select the
181 * CONFIG_SND_SOC_CS4270_VD33_ERRATA Kconfig option, and the driver will
182 * never select any sample rates that require divide-by-1.5.
183 */
184 struct cs4270_mode_ratios {
185 unsigned int ratio;
186 u8 speed_mode;
187 u8 mclk;
188 };
189
190 static struct cs4270_mode_ratios cs4270_mode_ratios[] = {
191 {64, CS4270_MODE_4X, CS4270_MODE_DIV1},
192 #ifndef CONFIG_SND_SOC_CS4270_VD33_ERRATA
193 {96, CS4270_MODE_4X, CS4270_MODE_DIV15},
194 #endif
195 {128, CS4270_MODE_2X, CS4270_MODE_DIV1},
196 {192, CS4270_MODE_4X, CS4270_MODE_DIV3},
197 {256, CS4270_MODE_1X, CS4270_MODE_DIV1},
198 {384, CS4270_MODE_2X, CS4270_MODE_DIV3},
199 {512, CS4270_MODE_1X, CS4270_MODE_DIV2},
200 {768, CS4270_MODE_1X, CS4270_MODE_DIV3},
201 {1024, CS4270_MODE_1X, CS4270_MODE_DIV4}
202 };
203
204 /* The number of MCLK/LRCK ratios supported by the CS4270 */
205 #define NUM_MCLK_RATIOS ARRAY_SIZE(cs4270_mode_ratios)
206
cs4270_reg_is_readable(struct device * dev,unsigned int reg)207 static bool cs4270_reg_is_readable(struct device *dev, unsigned int reg)
208 {
209 return (reg >= CS4270_FIRSTREG) && (reg <= CS4270_LASTREG);
210 }
211
cs4270_reg_is_volatile(struct device * dev,unsigned int reg)212 static bool cs4270_reg_is_volatile(struct device *dev, unsigned int reg)
213 {
214 /* Unreadable registers are considered volatile */
215 if ((reg < CS4270_FIRSTREG) || (reg > CS4270_LASTREG))
216 return true;
217
218 return reg == CS4270_CHIPID;
219 }
220
221 /**
222 * cs4270_set_dai_sysclk - determine the CS4270 samples rates.
223 * @codec_dai: the codec DAI
224 * @clk_id: the clock ID (ignored)
225 * @freq: the MCLK input frequency
226 * @dir: the clock direction (ignored)
227 *
228 * This function is used to tell the codec driver what the input MCLK
229 * frequency is.
230 *
231 * The value of MCLK is used to determine which sample rates are supported
232 * by the CS4270. The ratio of MCLK / Fs must be equal to one of nine
233 * supported values - 64, 96, 128, 192, 256, 384, 512, 768, and 1024.
234 *
235 * This function calculates the nine ratios and determines which ones match
236 * a standard sample rate. If there's a match, then it is added to the list
237 * of supported sample rates.
238 *
239 * This function must be called by the machine driver's 'startup' function,
240 * otherwise the list of supported sample rates will not be available in
241 * time for ALSA.
242 *
243 * For setups with variable MCLKs, pass 0 as 'freq' argument. This will cause
244 * theoretically possible sample rates to be enabled. Call it again with a
245 * proper value set one the external clock is set (most probably you would do
246 * that from a machine's driver 'hw_param' hook.
247 */
cs4270_set_dai_sysclk(struct snd_soc_dai * codec_dai,int clk_id,unsigned int freq,int dir)248 static int cs4270_set_dai_sysclk(struct snd_soc_dai *codec_dai,
249 int clk_id, unsigned int freq, int dir)
250 {
251 struct snd_soc_component *component = codec_dai->component;
252 struct cs4270_private *cs4270 = snd_soc_component_get_drvdata(component);
253
254 cs4270->mclk = freq;
255 return 0;
256 }
257
258 /**
259 * cs4270_set_dai_fmt - configure the codec for the selected audio format
260 * @codec_dai: the codec DAI
261 * @format: a SND_SOC_DAIFMT_x value indicating the data format
262 *
263 * This function takes a bitmask of SND_SOC_DAIFMT_x bits and programs the
264 * codec accordingly.
265 *
266 * Currently, this function only supports SND_SOC_DAIFMT_I2S and
267 * SND_SOC_DAIFMT_LEFT_J. The CS4270 codec also supports right-justified
268 * data for playback only, but ASoC currently does not support different
269 * formats for playback vs. record.
270 */
cs4270_set_dai_fmt(struct snd_soc_dai * codec_dai,unsigned int format)271 static int cs4270_set_dai_fmt(struct snd_soc_dai *codec_dai,
272 unsigned int format)
273 {
274 struct snd_soc_component *component = codec_dai->component;
275 struct cs4270_private *cs4270 = snd_soc_component_get_drvdata(component);
276
277 /* set DAI format */
278 switch (format & SND_SOC_DAIFMT_FORMAT_MASK) {
279 case SND_SOC_DAIFMT_I2S:
280 case SND_SOC_DAIFMT_LEFT_J:
281 cs4270->mode = format & SND_SOC_DAIFMT_FORMAT_MASK;
282 break;
283 default:
284 dev_err(component->dev, "invalid dai format\n");
285 return -EINVAL;
286 }
287
288 /* set master/slave audio interface */
289 switch (format & SND_SOC_DAIFMT_MASTER_MASK) {
290 case SND_SOC_DAIFMT_CBS_CFS:
291 cs4270->slave_mode = 1;
292 break;
293 case SND_SOC_DAIFMT_CBM_CFM:
294 cs4270->slave_mode = 0;
295 break;
296 default:
297 /* all other modes are unsupported by the hardware */
298 dev_err(component->dev, "Unknown master/slave configuration\n");
299 return -EINVAL;
300 }
301
302 return 0;
303 }
304
305 /**
306 * cs4270_hw_params - program the CS4270 with the given hardware parameters.
307 * @substream: the audio stream
308 * @params: the hardware parameters to set
309 * @dai: the SOC DAI (ignored)
310 *
311 * This function programs the hardware with the values provided.
312 * Specifically, the sample rate and the data format.
313 *
314 * The .ops functions are used to provide board-specific data, like input
315 * frequencies, to this driver. This function takes that information,
316 * combines it with the hardware parameters provided, and programs the
317 * hardware accordingly.
318 */
cs4270_hw_params(struct snd_pcm_substream * substream,struct snd_pcm_hw_params * params,struct snd_soc_dai * dai)319 static int cs4270_hw_params(struct snd_pcm_substream *substream,
320 struct snd_pcm_hw_params *params,
321 struct snd_soc_dai *dai)
322 {
323 struct snd_soc_component *component = dai->component;
324 struct cs4270_private *cs4270 = snd_soc_component_get_drvdata(component);
325 int ret;
326 unsigned int i;
327 unsigned int rate;
328 unsigned int ratio;
329 int reg;
330
331 /* Figure out which MCLK/LRCK ratio to use */
332
333 rate = params_rate(params); /* Sampling rate, in Hz */
334 ratio = cs4270->mclk / rate; /* MCLK/LRCK ratio */
335
336 for (i = 0; i < NUM_MCLK_RATIOS; i++) {
337 if (cs4270_mode_ratios[i].ratio == ratio)
338 break;
339 }
340
341 if (i == NUM_MCLK_RATIOS) {
342 /* We did not find a matching ratio */
343 dev_err(component->dev, "could not find matching ratio\n");
344 return -EINVAL;
345 }
346
347 /* Set the sample rate */
348
349 reg = snd_soc_component_read(component, CS4270_MODE);
350 reg &= ~(CS4270_MODE_SPEED_MASK | CS4270_MODE_DIV_MASK);
351 reg |= cs4270_mode_ratios[i].mclk;
352
353 if (cs4270->slave_mode)
354 reg |= CS4270_MODE_SLAVE;
355 else
356 reg |= cs4270_mode_ratios[i].speed_mode;
357
358 ret = snd_soc_component_write(component, CS4270_MODE, reg);
359 if (ret < 0) {
360 dev_err(component->dev, "i2c write failed\n");
361 return ret;
362 }
363
364 /* Set the DAI format */
365
366 reg = snd_soc_component_read(component, CS4270_FORMAT);
367 reg &= ~(CS4270_FORMAT_DAC_MASK | CS4270_FORMAT_ADC_MASK);
368
369 switch (cs4270->mode) {
370 case SND_SOC_DAIFMT_I2S:
371 reg |= CS4270_FORMAT_DAC_I2S | CS4270_FORMAT_ADC_I2S;
372 break;
373 case SND_SOC_DAIFMT_LEFT_J:
374 reg |= CS4270_FORMAT_DAC_LJ | CS4270_FORMAT_ADC_LJ;
375 break;
376 default:
377 dev_err(component->dev, "unknown dai format\n");
378 return -EINVAL;
379 }
380
381 ret = snd_soc_component_write(component, CS4270_FORMAT, reg);
382 if (ret < 0) {
383 dev_err(component->dev, "i2c write failed\n");
384 return ret;
385 }
386
387 return ret;
388 }
389
390 /**
391 * cs4270_dai_mute - enable/disable the CS4270 external mute
392 * @dai: the SOC DAI
393 * @mute: 0 = disable mute, 1 = enable mute
394 * @direction: (ignored)
395 *
396 * This function toggles the mute bits in the MUTE register. The CS4270's
397 * mute capability is intended for external muting circuitry, so if the
398 * board does not have the MUTEA or MUTEB pins connected to such circuitry,
399 * then this function will do nothing.
400 */
cs4270_dai_mute(struct snd_soc_dai * dai,int mute,int direction)401 static int cs4270_dai_mute(struct snd_soc_dai *dai, int mute, int direction)
402 {
403 struct snd_soc_component *component = dai->component;
404 struct cs4270_private *cs4270 = snd_soc_component_get_drvdata(component);
405 int reg6;
406
407 reg6 = snd_soc_component_read(component, CS4270_MUTE);
408
409 if (mute)
410 reg6 |= CS4270_MUTE_DAC_A | CS4270_MUTE_DAC_B;
411 else {
412 reg6 &= ~(CS4270_MUTE_DAC_A | CS4270_MUTE_DAC_B);
413 reg6 |= cs4270->manual_mute;
414 }
415
416 return snd_soc_component_write(component, CS4270_MUTE, reg6);
417 }
418
419 /**
420 * cs4270_soc_put_mute - put callback for the 'Master Playback switch'
421 * alsa control.
422 * @kcontrol: mixer control
423 * @ucontrol: control element information
424 *
425 * This function basically passes the arguments on to the generic
426 * snd_soc_put_volsw() function and saves the mute information in
427 * our private data structure. This is because we want to prevent
428 * cs4270_dai_mute() neglecting the user's decision to manually
429 * mute the codec's output.
430 *
431 * Returns 0 for success.
432 */
cs4270_soc_put_mute(struct snd_kcontrol * kcontrol,struct snd_ctl_elem_value * ucontrol)433 static int cs4270_soc_put_mute(struct snd_kcontrol *kcontrol,
434 struct snd_ctl_elem_value *ucontrol)
435 {
436 struct snd_soc_component *component = snd_soc_kcontrol_component(kcontrol);
437 struct cs4270_private *cs4270 = snd_soc_component_get_drvdata(component);
438 int left = !ucontrol->value.integer.value[0];
439 int right = !ucontrol->value.integer.value[1];
440
441 cs4270->manual_mute = (left ? CS4270_MUTE_DAC_A : 0) |
442 (right ? CS4270_MUTE_DAC_B : 0);
443
444 return snd_soc_put_volsw(kcontrol, ucontrol);
445 }
446
447 /* A list of non-DAPM controls that the CS4270 supports */
448 static const struct snd_kcontrol_new cs4270_snd_controls[] = {
449 SOC_DOUBLE_R("Master Playback Volume",
450 CS4270_VOLA, CS4270_VOLB, 0, 0xFF, 1),
451 SOC_SINGLE("Digital Sidetone Switch", CS4270_FORMAT, 5, 1, 0),
452 SOC_SINGLE("Soft Ramp Switch", CS4270_TRANS, 6, 1, 0),
453 SOC_SINGLE("Zero Cross Switch", CS4270_TRANS, 5, 1, 0),
454 SOC_SINGLE("De-emphasis filter", CS4270_TRANS, 0, 1, 0),
455 SOC_SINGLE("Popguard Switch", CS4270_MODE, 0, 1, 1),
456 SOC_SINGLE("Auto-Mute Switch", CS4270_MUTE, 5, 1, 0),
457 SOC_DOUBLE("Master Capture Switch", CS4270_MUTE, 3, 4, 1, 1),
458 SOC_DOUBLE_EXT("Master Playback Switch", CS4270_MUTE, 0, 1, 1, 1,
459 snd_soc_get_volsw, cs4270_soc_put_mute),
460 };
461
462 static const struct snd_soc_dai_ops cs4270_dai_ops = {
463 .hw_params = cs4270_hw_params,
464 .set_sysclk = cs4270_set_dai_sysclk,
465 .set_fmt = cs4270_set_dai_fmt,
466 .mute_stream = cs4270_dai_mute,
467 .no_capture_mute = 1,
468 };
469
470 static struct snd_soc_dai_driver cs4270_dai = {
471 .name = "cs4270-hifi",
472 .playback = {
473 .stream_name = "Playback",
474 .channels_min = 2,
475 .channels_max = 2,
476 .rates = SNDRV_PCM_RATE_CONTINUOUS,
477 .rate_min = 4000,
478 .rate_max = 216000,
479 .formats = CS4270_FORMATS,
480 },
481 .capture = {
482 .stream_name = "Capture",
483 .channels_min = 2,
484 .channels_max = 2,
485 .rates = SNDRV_PCM_RATE_CONTINUOUS,
486 .rate_min = 4000,
487 .rate_max = 216000,
488 .formats = CS4270_FORMATS,
489 },
490 .ops = &cs4270_dai_ops,
491 };
492
493 /**
494 * cs4270_probe - ASoC probe function
495 * @component: ASoC component
496 *
497 * This function is called when ASoC has all the pieces it needs to
498 * instantiate a sound driver.
499 */
cs4270_probe(struct snd_soc_component * component)500 static int cs4270_probe(struct snd_soc_component *component)
501 {
502 struct cs4270_private *cs4270 = snd_soc_component_get_drvdata(component);
503 int ret;
504
505 /* Disable auto-mute. This feature appears to be buggy. In some
506 * situations, auto-mute will not deactivate when it should, so we want
507 * this feature disabled by default. An application (e.g. alsactl) can
508 * re-enabled it by using the controls.
509 */
510 ret = snd_soc_component_update_bits(component, CS4270_MUTE, CS4270_MUTE_AUTO, 0);
511 if (ret < 0) {
512 dev_err(component->dev, "i2c write failed\n");
513 return ret;
514 }
515
516 /* Disable automatic volume control. The hardware enables, and it
517 * causes volume change commands to be delayed, sometimes until after
518 * playback has started. An application (e.g. alsactl) can
519 * re-enabled it by using the controls.
520 */
521 ret = snd_soc_component_update_bits(component, CS4270_TRANS,
522 CS4270_TRANS_SOFT | CS4270_TRANS_ZERO, 0);
523 if (ret < 0) {
524 dev_err(component->dev, "i2c write failed\n");
525 return ret;
526 }
527
528 ret = regulator_bulk_enable(ARRAY_SIZE(cs4270->supplies),
529 cs4270->supplies);
530
531 return ret;
532 }
533
534 /**
535 * cs4270_remove - ASoC remove function
536 * @component: ASoC component
537 *
538 * This function is the counterpart to cs4270_probe().
539 */
cs4270_remove(struct snd_soc_component * component)540 static void cs4270_remove(struct snd_soc_component *component)
541 {
542 struct cs4270_private *cs4270 = snd_soc_component_get_drvdata(component);
543
544 regulator_bulk_disable(ARRAY_SIZE(cs4270->supplies), cs4270->supplies);
545 };
546
547 #ifdef CONFIG_PM
548
549 /* This suspend/resume implementation can handle both - a simple standby
550 * where the codec remains powered, and a full suspend, where the voltage
551 * domain the codec is connected to is teared down and/or any other hardware
552 * reset condition is asserted.
553 *
554 * The codec's own power saving features are enabled in the suspend callback,
555 * and all registers are written back to the hardware when resuming.
556 */
557
cs4270_soc_suspend(struct snd_soc_component * component)558 static int cs4270_soc_suspend(struct snd_soc_component *component)
559 {
560 struct cs4270_private *cs4270 = snd_soc_component_get_drvdata(component);
561 int reg, ret;
562
563 reg = snd_soc_component_read(component, CS4270_PWRCTL) | CS4270_PWRCTL_PDN_ALL;
564 if (reg < 0)
565 return reg;
566
567 ret = snd_soc_component_write(component, CS4270_PWRCTL, reg);
568 if (ret < 0)
569 return ret;
570
571 regulator_bulk_disable(ARRAY_SIZE(cs4270->supplies),
572 cs4270->supplies);
573
574 return 0;
575 }
576
cs4270_soc_resume(struct snd_soc_component * component)577 static int cs4270_soc_resume(struct snd_soc_component *component)
578 {
579 struct cs4270_private *cs4270 = snd_soc_component_get_drvdata(component);
580 int reg, ret;
581
582 ret = regulator_bulk_enable(ARRAY_SIZE(cs4270->supplies),
583 cs4270->supplies);
584 if (ret != 0)
585 return ret;
586
587 /* In case the device was put to hard reset during sleep, we need to
588 * wait 500ns here before any I2C communication. */
589 ndelay(500);
590
591 /* first restore the entire register cache ... */
592 regcache_sync(cs4270->regmap);
593
594 /* ... then disable the power-down bits */
595 reg = snd_soc_component_read(component, CS4270_PWRCTL);
596 reg &= ~CS4270_PWRCTL_PDN_ALL;
597
598 return snd_soc_component_write(component, CS4270_PWRCTL, reg);
599 }
600 #else
601 #define cs4270_soc_suspend NULL
602 #define cs4270_soc_resume NULL
603 #endif /* CONFIG_PM */
604
605 /*
606 * ASoC codec driver structure
607 */
608 static const struct snd_soc_component_driver soc_component_device_cs4270 = {
609 .probe = cs4270_probe,
610 .remove = cs4270_remove,
611 .suspend = cs4270_soc_suspend,
612 .resume = cs4270_soc_resume,
613 .controls = cs4270_snd_controls,
614 .num_controls = ARRAY_SIZE(cs4270_snd_controls),
615 .dapm_widgets = cs4270_dapm_widgets,
616 .num_dapm_widgets = ARRAY_SIZE(cs4270_dapm_widgets),
617 .dapm_routes = cs4270_dapm_routes,
618 .num_dapm_routes = ARRAY_SIZE(cs4270_dapm_routes),
619 .idle_bias_on = 1,
620 .use_pmdown_time = 1,
621 .endianness = 1,
622 };
623
624 /*
625 * cs4270_of_match - the device tree bindings
626 */
627 static const struct of_device_id cs4270_of_match[] = {
628 { .compatible = "cirrus,cs4270", },
629 { }
630 };
631 MODULE_DEVICE_TABLE(of, cs4270_of_match);
632
633 static const struct regmap_config cs4270_regmap = {
634 .reg_bits = 8,
635 .val_bits = 8,
636 .max_register = CS4270_LASTREG,
637 .reg_defaults = cs4270_reg_defaults,
638 .num_reg_defaults = ARRAY_SIZE(cs4270_reg_defaults),
639 .cache_type = REGCACHE_MAPLE,
640 .write_flag_mask = CS4270_I2C_INCR,
641
642 .readable_reg = cs4270_reg_is_readable,
643 .volatile_reg = cs4270_reg_is_volatile,
644 };
645
646 /**
647 * cs4270_i2c_remove - deinitialize the I2C interface of the CS4270
648 * @i2c_client: the I2C client object
649 *
650 * This function puts the chip into low power mode when the i2c device
651 * is removed.
652 */
cs4270_i2c_remove(struct i2c_client * i2c_client)653 static void cs4270_i2c_remove(struct i2c_client *i2c_client)
654 {
655 struct cs4270_private *cs4270 = i2c_get_clientdata(i2c_client);
656
657 gpiod_set_value_cansleep(cs4270->reset_gpio, 0);
658 }
659
660 /**
661 * cs4270_i2c_probe - initialize the I2C interface of the CS4270
662 * @i2c_client: the I2C client object
663 *
664 * This function is called whenever the I2C subsystem finds a device that
665 * matches the device ID given via a prior call to i2c_add_driver().
666 */
cs4270_i2c_probe(struct i2c_client * i2c_client)667 static int cs4270_i2c_probe(struct i2c_client *i2c_client)
668 {
669 struct cs4270_private *cs4270;
670 unsigned int val;
671 int ret, i;
672
673 cs4270 = devm_kzalloc(&i2c_client->dev, sizeof(struct cs4270_private),
674 GFP_KERNEL);
675 if (!cs4270)
676 return -ENOMEM;
677
678 /* get the power supply regulators */
679 for (i = 0; i < ARRAY_SIZE(supply_names); i++)
680 cs4270->supplies[i].supply = supply_names[i];
681
682 ret = devm_regulator_bulk_get(&i2c_client->dev,
683 ARRAY_SIZE(cs4270->supplies),
684 cs4270->supplies);
685 if (ret < 0)
686 return ret;
687
688 /* reset the device */
689 cs4270->reset_gpio = devm_gpiod_get_optional(&i2c_client->dev, "reset",
690 GPIOD_OUT_LOW);
691 if (IS_ERR(cs4270->reset_gpio)) {
692 dev_dbg(&i2c_client->dev, "Error getting CS4270 reset GPIO\n");
693 return PTR_ERR(cs4270->reset_gpio);
694 }
695
696 if (cs4270->reset_gpio) {
697 dev_dbg(&i2c_client->dev, "Found reset GPIO\n");
698 gpiod_set_value_cansleep(cs4270->reset_gpio, 1);
699 }
700
701 /* Sleep 500ns before i2c communications */
702 ndelay(500);
703
704 cs4270->regmap = devm_regmap_init_i2c(i2c_client, &cs4270_regmap);
705 if (IS_ERR(cs4270->regmap))
706 return PTR_ERR(cs4270->regmap);
707
708 /* Verify that we have a CS4270 */
709 ret = regmap_read(cs4270->regmap, CS4270_CHIPID, &val);
710 if (ret < 0) {
711 dev_err(&i2c_client->dev, "failed to read i2c at addr %X\n",
712 i2c_client->addr);
713 return ret;
714 }
715 /* The top four bits of the chip ID should be 1100. */
716 if ((val & 0xF0) != 0xC0) {
717 dev_err(&i2c_client->dev, "device at addr %X is not a CS4270\n",
718 i2c_client->addr);
719 return -ENODEV;
720 }
721
722 dev_info(&i2c_client->dev, "found device at i2c address %X\n",
723 i2c_client->addr);
724 dev_info(&i2c_client->dev, "hardware revision %X\n", val & 0xF);
725
726 i2c_set_clientdata(i2c_client, cs4270);
727
728 ret = devm_snd_soc_register_component(&i2c_client->dev,
729 &soc_component_device_cs4270, &cs4270_dai, 1);
730 return ret;
731 }
732
733 /*
734 * cs4270_id - I2C device IDs supported by this driver
735 */
736 static const struct i2c_device_id cs4270_id[] = {
737 {"cs4270"},
738 {}
739 };
740 MODULE_DEVICE_TABLE(i2c, cs4270_id);
741
742 /*
743 * cs4270_i2c_driver - I2C device identification
744 *
745 * This structure tells the I2C subsystem how to identify and support a
746 * given I2C device type.
747 */
748 static struct i2c_driver cs4270_i2c_driver = {
749 .driver = {
750 .name = "cs4270",
751 .of_match_table = cs4270_of_match,
752 },
753 .id_table = cs4270_id,
754 .probe = cs4270_i2c_probe,
755 .remove = cs4270_i2c_remove,
756 };
757
758 module_i2c_driver(cs4270_i2c_driver);
759
760 MODULE_AUTHOR("Timur Tabi <timur@freescale.com>");
761 MODULE_DESCRIPTION("Cirrus Logic CS4270 ALSA SoC Codec Driver");
762 MODULE_LICENSE("GPL");
763