xref: /linux/scripts/dtc/include-prefixes/arm64/renesas/rzg2l-smarc-som.dtsi (revision 0c436dfe5c25d0931b164b944165259f95e5281f) 
1// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
2/*
3 * Device Tree Source for the RZ/{G2L,V2L} SMARC SOM common parts
4 *
5 * Copyright (C) 2021 Renesas Electronics Corp.
6 */
7
8#include <dt-bindings/gpio/gpio.h>
9#include <dt-bindings/interrupt-controller/irqc-rzg2l.h>
10#include <dt-bindings/pinctrl/rzg2l-pinctrl.h>
11
12/* SW1[2] should be at position 2/OFF to enable 64 GB eMMC */
13#define EMMC	1
14
15/*
16 * To enable uSD card on CN3,
17 * SW1[2] should be at position 3/ON.
18 * Disable eMMC by setting "#define EMMC	0" above.
19 */
20#define SDHI	(!EMMC)
21
22/ {
23	aliases {
24		ethernet0 = &eth0;
25		ethernet1 = &eth1;
26	};
27
28	chosen {
29		bootargs = "ignore_loglevel rw root=/dev/nfs ip=on";
30	};
31
32	memory@48000000 {
33		device_type = "memory";
34		/* first 128MB is reserved for secure area. */
35		reg = <0x0 0x48000000 0x0 0x78000000>;
36	};
37
38	reg_1p8v: regulator-1p8v {
39		compatible = "regulator-fixed";
40		regulator-name = "fixed-1.8V";
41		regulator-min-microvolt = <1800000>;
42		regulator-max-microvolt = <1800000>;
43		regulator-boot-on;
44		regulator-always-on;
45	};
46
47	reg_3p3v: regulator-3p3v {
48		compatible = "regulator-fixed";
49		regulator-name = "fixed-3.3V";
50		regulator-min-microvolt = <3300000>;
51		regulator-max-microvolt = <3300000>;
52		regulator-boot-on;
53		regulator-always-on;
54	};
55
56	reg_1p1v: regulator-vdd-core {
57		compatible = "regulator-fixed";
58		regulator-name = "fixed-1.1V";
59		regulator-min-microvolt = <1100000>;
60		regulator-max-microvolt = <1100000>;
61		regulator-boot-on;
62		regulator-always-on;
63	};
64
65	vccq_sdhi0: regulator-vccq-sdhi0 {
66		compatible = "regulator-gpio";
67
68		regulator-name = "SDHI0 VccQ";
69		regulator-min-microvolt = <1800000>;
70		regulator-max-microvolt = <3300000>;
71		states = <3300000 1>, <1800000 0>;
72		regulator-boot-on;
73		gpios = <&pinctrl RZG2L_GPIO(39, 0) GPIO_ACTIVE_HIGH>;
74		regulator-always-on;
75	};
76
77	/* 32.768kHz crystal */
78	x2: x2-clock {
79		compatible = "fixed-clock";
80		#clock-cells = <0>;
81		clock-frequency = <32768>;
82	};
83};
84
85&adc {
86	pinctrl-0 = <&adc_pins>;
87	pinctrl-names = "default";
88	status = "okay";
89
90	/delete-node/ channel@6;
91	/delete-node/ channel@7;
92};
93
94&eth0 {
95	pinctrl-0 = <&eth0_pins>;
96	pinctrl-names = "default";
97	phy-handle = <&phy0>;
98	phy-mode = "rgmii-id";
99	status = "okay";
100
101	phy0: ethernet-phy@7 {
102		compatible = "ethernet-phy-id0022.1640",
103			     "ethernet-phy-ieee802.3-c22";
104		reg = <7>;
105		interrupt-parent = <&irqc>;
106		interrupts = <RZG2L_IRQ2 IRQ_TYPE_LEVEL_LOW>;
107		rxc-skew-psec = <2400>;
108		txc-skew-psec = <2400>;
109		rxdv-skew-psec = <0>;
110		txen-skew-psec = <0>;
111		rxd0-skew-psec = <0>;
112		rxd1-skew-psec = <0>;
113		rxd2-skew-psec = <0>;
114		rxd3-skew-psec = <0>;
115		txd0-skew-psec = <0>;
116		txd1-skew-psec = <0>;
117		txd2-skew-psec = <0>;
118		txd3-skew-psec = <0>;
119	};
120};
121
122&eth1 {
123	pinctrl-0 = <&eth1_pins>;
124	pinctrl-names = "default";
125	phy-handle = <&phy1>;
126	phy-mode = "rgmii-id";
127	status = "okay";
128
129	phy1: ethernet-phy@7 {
130		compatible = "ethernet-phy-id0022.1640",
131			     "ethernet-phy-ieee802.3-c22";
132		reg = <7>;
133		interrupt-parent = <&irqc>;
134		interrupts = <RZG2L_IRQ3 IRQ_TYPE_LEVEL_LOW>;
135		rxc-skew-psec = <2400>;
136		txc-skew-psec = <2400>;
137		rxdv-skew-psec = <0>;
138		txen-skew-psec = <0>;
139		rxd0-skew-psec = <0>;
140		rxd1-skew-psec = <0>;
141		rxd2-skew-psec = <0>;
142		rxd3-skew-psec = <0>;
143		txd0-skew-psec = <0>;
144		txd1-skew-psec = <0>;
145		txd2-skew-psec = <0>;
146		txd3-skew-psec = <0>;
147	};
148};
149
150&extal_clk {
151	clock-frequency = <24000000>;
152};
153
154&gpu {
155	mali-supply = <&reg_1p1v>;
156};
157
158&i2c3 {
159	raa215300: pmic@12 {
160		compatible = "renesas,raa215300";
161		reg = <0x12>, <0x6f>;
162		reg-names = "main", "rtc";
163
164		clocks = <&x2>;
165		clock-names = "xin";
166	};
167};
168
169&ostm1 {
170	status = "okay";
171};
172
173&ostm2 {
174	status = "okay";
175};
176
177&pinctrl {
178	adc_pins: adc {
179		pinmux = <RZG2L_PORT_PINMUX(9, 0, 2)>; /* ADC_TRG */
180	};
181
182	eth0_pins: eth0 {
183		txc {
184			pinmux = <RZG2L_PORT_PINMUX(20, 0, 1)>; /* ET0_TXC */
185			power-source = <1800>;
186			output-enable;
187		};
188
189		mux {
190			pinmux = <RZG2L_PORT_PINMUX(28, 1, 1)>, /* ET0_LINKSTA */
191				 <RZG2L_PORT_PINMUX(27, 1, 1)>, /* ET0_MDC */
192				 <RZG2L_PORT_PINMUX(28, 0, 1)>, /* ET0_MDIO */
193				 <RZG2L_PORT_PINMUX(20, 1, 1)>, /* ET0_TX_CTL */
194				 <RZG2L_PORT_PINMUX(20, 2, 1)>, /* ET0_TXD0 */
195				 <RZG2L_PORT_PINMUX(21, 0, 1)>, /* ET0_TXD1 */
196				 <RZG2L_PORT_PINMUX(21, 1, 1)>, /* ET0_TXD2 */
197				 <RZG2L_PORT_PINMUX(22, 0, 1)>, /* ET0_TXD3 */
198				 <RZG2L_PORT_PINMUX(24, 0, 1)>, /* ET0_RXC */
199				 <RZG2L_PORT_PINMUX(24, 1, 1)>, /* ET0_RX_CTL */
200				 <RZG2L_PORT_PINMUX(25, 0, 1)>, /* ET0_RXD0 */
201				 <RZG2L_PORT_PINMUX(25, 1, 1)>, /* ET0_RXD1 */
202				 <RZG2L_PORT_PINMUX(26, 0, 1)>, /* ET0_RXD2 */
203				 <RZG2L_PORT_PINMUX(26, 1, 1)>; /* ET0_RXD3 */
204			power-source = <1800>;
205		};
206
207		irq {
208			pinmux = <RZG2L_PORT_PINMUX(1, 0, 1)>;  /* IRQ2 */
209		};
210	};
211
212	eth1_pins: eth1 {
213		txc {
214			pinmux = <RZG2L_PORT_PINMUX(29, 0, 1)>; /* ET1_TXC */
215			power-source = <1800>;
216			output-enable;
217		};
218
219		mux {
220			pinmux = <RZG2L_PORT_PINMUX(37, 2, 1)>, /* ET1_LINKSTA */
221				 <RZG2L_PORT_PINMUX(37, 0, 1)>, /* ET1_MDC */
222				 <RZG2L_PORT_PINMUX(37, 1, 1)>, /* ET1_MDIO */
223				 <RZG2L_PORT_PINMUX(29, 1, 1)>, /* ET1_TX_CTL */
224				 <RZG2L_PORT_PINMUX(30, 0, 1)>, /* ET1_TXD0 */
225				 <RZG2L_PORT_PINMUX(30, 1, 1)>, /* ET1_TXD1 */
226				 <RZG2L_PORT_PINMUX(31, 0, 1)>, /* ET1_TXD2 */
227				 <RZG2L_PORT_PINMUX(31, 1, 1)>, /* ET1_TXD3 */
228				 <RZG2L_PORT_PINMUX(33, 1, 1)>, /* ET1_RXC */
229				 <RZG2L_PORT_PINMUX(34, 0, 1)>, /* ET1_RX_CTL */
230				 <RZG2L_PORT_PINMUX(34, 1, 1)>, /* ET1_RXD0 */
231				 <RZG2L_PORT_PINMUX(35, 0, 1)>, /* ET1_RXD1 */
232				 <RZG2L_PORT_PINMUX(35, 1, 1)>, /* ET1_RXD2 */
233				 <RZG2L_PORT_PINMUX(36, 0, 1)>; /* ET1_RXD3 */
234			power-source = <1800>;
235		};
236
237		irq {
238			pinmux = <RZG2L_PORT_PINMUX(1, 1, 1)>;  /* IRQ3 */
239		};
240	};
241
242	gpio-sd0-pwr-en-hog {
243		gpio-hog;
244		gpios = <RZG2L_GPIO(4, 1) GPIO_ACTIVE_HIGH>;
245		output-high;
246		line-name = "gpio_sd0_pwr_en";
247	};
248
249	qspi0_pins: qspi0 {
250		qspi0-data {
251			pins = "QSPI0_IO0", "QSPI0_IO1", "QSPI0_IO2", "QSPI0_IO3";
252			power-source = <1800>;
253		};
254
255		qspi0-ctrl {
256			pins = "QSPI0_SPCLK", "QSPI0_SSL", "QSPI_RESET#";
257			power-source = <1800>;
258		};
259	};
260
261	/*
262	 * SD0 device selection is XOR between GPIO_SD0_DEV_SEL and SW1[2]
263	 * The below switch logic can be used to select the device between
264	 * eMMC and microSD, after setting GPIO_SD0_DEV_SEL to high in DT.
265	 * SW1[2] should be at position 2/OFF to enable 64 GB eMMC
266	 * SW1[2] should be at position 3/ON to enable uSD card CN3
267	 */
268	sd0-dev-sel-hog {
269		gpio-hog;
270		gpios = <RZG2L_GPIO(41, 1) GPIO_ACTIVE_HIGH>;
271		output-high;
272		line-name = "sd0_dev_sel";
273	};
274
275	sdhi0_emmc_pins: sd0emmc {
276		sd0_emmc_data {
277			pins = "SD0_DATA0", "SD0_DATA1", "SD0_DATA2", "SD0_DATA3",
278			       "SD0_DATA4", "SD0_DATA5", "SD0_DATA6", "SD0_DATA7";
279			power-source = <1800>;
280		};
281
282		sd0_emmc_ctrl {
283			pins = "SD0_CLK", "SD0_CMD";
284			power-source = <1800>;
285		};
286
287		sd0_emmc_rst {
288			pins = "SD0_RST#";
289			power-source = <1800>;
290		};
291	};
292
293	sdhi0_pins: sd0 {
294		sd0_data {
295			pins = "SD0_DATA0", "SD0_DATA1", "SD0_DATA2", "SD0_DATA3";
296			power-source = <3300>;
297		};
298
299		sd0_ctrl {
300			pins = "SD0_CLK", "SD0_CMD";
301			power-source = <3300>;
302		};
303
304		sd0_mux {
305			pinmux = <RZG2L_PORT_PINMUX(47, 0, 2)>; /* SD0_CD */
306		};
307	};
308
309	sdhi0_pins_uhs: sd0_uhs {
310		sd0_data_uhs {
311			pins = "SD0_DATA0", "SD0_DATA1", "SD0_DATA2", "SD0_DATA3";
312			power-source = <1800>;
313		};
314
315		sd0_ctrl_uhs {
316			pins = "SD0_CLK", "SD0_CMD";
317			power-source = <1800>;
318		};
319
320		sd0_mux_uhs {
321			pinmux = <RZG2L_PORT_PINMUX(47, 0, 2)>; /* SD0_CD */
322		};
323	};
324};
325
326&sbc {
327	pinctrl-0 = <&qspi0_pins>;
328	pinctrl-names = "default";
329	status = "okay";
330
331	flash@0 {
332		compatible = "micron,mt25qu512a", "jedec,spi-nor";
333		reg = <0>;
334		m25p,fast-read;
335		spi-max-frequency = <50000000>;
336		spi-rx-bus-width = <4>;
337		spi-tx-bus-width = <4>;
338
339		partitions {
340			compatible = "fixed-partitions";
341			#address-cells = <1>;
342			#size-cells = <1>;
343
344			boot@0 {
345				reg = <0x00000000 0x2000000>;
346				read-only;
347			};
348			user@2000000 {
349				reg = <0x2000000 0x2000000>;
350			};
351		};
352	};
353};
354
355#if SDHI
356&sdhi0 {
357	pinctrl-0 = <&sdhi0_pins>;
358	pinctrl-1 = <&sdhi0_pins_uhs>;
359	pinctrl-names = "default", "state_uhs";
360
361	vmmc-supply = <&reg_3p3v>;
362	vqmmc-supply = <&vccq_sdhi0>;
363	bus-width = <4>;
364	sd-uhs-sdr50;
365	sd-uhs-sdr104;
366	status = "okay";
367};
368#endif
369
370#if EMMC
371&sdhi0 {
372	pinctrl-0 = <&sdhi0_emmc_pins>;
373	pinctrl-1 = <&sdhi0_emmc_pins>;
374	pinctrl-names = "default", "state_uhs";
375
376	vmmc-supply = <&reg_3p3v>;
377	vqmmc-supply = <&reg_1p8v>;
378	bus-width = <8>;
379	mmc-hs200-1_8v;
380	non-removable;
381	fixed-emmc-driver-type = <1>;
382	status = "okay";
383};
384#endif
385
386&wdt0 {
387	status = "okay";
388	timeout-sec = <60>;
389};
390
391&wdt1 {
392	status = "okay";
393	timeout-sec = <60>;
394};
395