1 /* SPDX-License-Identifier: GPL-2.0-only */ 2 /* 3 * driver.h -- SoC Regulator driver support. 4 * 5 * Copyright (C) 2007, 2008 Wolfson Microelectronics PLC. 6 * 7 * Author: Liam Girdwood <lrg@slimlogic.co.uk> 8 * 9 * Regulator Driver Interface. 10 */ 11 12 #ifndef __LINUX_REGULATOR_DRIVER_H_ 13 #define __LINUX_REGULATOR_DRIVER_H_ 14 15 #include <linux/device.h> 16 #include <linux/linear_range.h> 17 #include <linux/notifier.h> 18 #include <linux/regulator/consumer.h> 19 #include <linux/ww_mutex.h> 20 21 struct gpio_desc; 22 struct regmap; 23 struct regulator_dev; 24 struct regulator_config; 25 struct regulator_init_data; 26 struct regulator_enable_gpio; 27 28 enum regulator_status { 29 REGULATOR_STATUS_OFF, 30 REGULATOR_STATUS_ON, 31 REGULATOR_STATUS_ERROR, 32 /* fast/normal/idle/standby are flavors of "on" */ 33 REGULATOR_STATUS_FAST, 34 REGULATOR_STATUS_NORMAL, 35 REGULATOR_STATUS_IDLE, 36 REGULATOR_STATUS_STANDBY, 37 /* The regulator is enabled but not regulating */ 38 REGULATOR_STATUS_BYPASS, 39 /* in case that any other status doesn't apply */ 40 REGULATOR_STATUS_UNDEFINED, 41 }; 42 43 enum regulator_detection_severity { 44 /* Hardware shut down voltage outputs if condition is detected */ 45 REGULATOR_SEVERITY_PROT, 46 /* Hardware is probably damaged/inoperable */ 47 REGULATOR_SEVERITY_ERR, 48 /* Hardware is still recoverable but recovery action must be taken */ 49 REGULATOR_SEVERITY_WARN, 50 }; 51 52 /* Initialize struct linear_range for regulators */ 53 #define REGULATOR_LINEAR_RANGE(_min_uV, _min_sel, _max_sel, _step_uV) \ 54 LINEAR_RANGE(_min_uV, _min_sel, _max_sel, _step_uV) 55 56 /* Initialize struct linear_range using voltages, not selectors */ 57 #define REGULATOR_LINEAR_VRANGE(_offs_uV, _min_uV, _max_uV, _step_uV) \ 58 LINEAR_RANGE(_min_uV, ((_min_uV) - (_offs_uV)) / (_step_uV), \ 59 ((_max_uV) - (_offs_uV)) / (_step_uV), _step_uV) 60 61 /** 62 * struct regulator_ops - regulator operations. 63 * 64 * @enable: Configure the regulator as enabled. 65 * @disable: Configure the regulator as disabled. 66 * @is_enabled: Return 1 if the regulator is enabled, 0 if not. 67 * May also return negative errno. 68 * 69 * @set_voltage: Set the voltage for the regulator within the range specified. 70 * The driver should select the voltage closest to min_uV. 71 * @set_voltage_sel: Set the voltage for the regulator using the specified 72 * selector. 73 * @map_voltage: Convert a voltage into a selector 74 * @get_voltage: Return the currently configured voltage for the regulator; 75 * return -ENOTRECOVERABLE if regulator can't be read at 76 * bootup and hasn't been set yet. 77 * @get_voltage_sel: Return the currently configured voltage selector for the 78 * regulator; return -ENOTRECOVERABLE if regulator can't 79 * be read at bootup and hasn't been set yet. 80 * @list_voltage: Return one of the supported voltages, in microvolts; zero 81 * if the selector indicates a voltage that is unusable on this system; 82 * or negative errno. Selectors range from zero to one less than 83 * regulator_desc.n_voltages. Voltages may be reported in any order. 84 * 85 * @set_current_limit: Configure a limit for a current-limited regulator. 86 * The driver should select the current closest to max_uA. 87 * @get_current_limit: Get the configured limit for a current-limited regulator. 88 * @set_input_current_limit: Configure an input limit. 89 * 90 * @set_over_current_protection: Support enabling of and setting limits for over 91 * current situation detection. Detection can be configured for three 92 * levels of severity. 93 * 94 * - REGULATOR_SEVERITY_PROT should automatically shut down the regulator(s). 95 * 96 * - REGULATOR_SEVERITY_ERR should indicate that over-current situation is 97 * caused by an unrecoverable error but HW does not perform 98 * automatic shut down. 99 * 100 * - REGULATOR_SEVERITY_WARN should indicate situation where hardware is 101 * still believed to not be damaged but that a board sepcific 102 * recovery action is needed. If lim_uA is 0 the limit should not 103 * be changed but the detection should just be enabled/disabled as 104 * is requested. 105 * 106 * @set_over_voltage_protection: Support enabling of and setting limits for over 107 * voltage situation detection. Detection can be configured for same 108 * severities as over current protection. Units of uV. 109 * @set_under_voltage_protection: Support enabling of and setting limits for 110 * under voltage situation detection. Detection can be configured for same 111 * severities as over current protection. Units of uV. 112 * @set_thermal_protection: Support enabling of and setting limits for over 113 * temperature situation detection.Detection can be configured for same 114 * severities as over current protection. Units of degree Kelvin. 115 * 116 * @set_active_discharge: Set active discharge enable/disable of regulators. 117 * 118 * @set_mode: Set the configured operating mode for the regulator. 119 * @get_mode: Get the configured operating mode for the regulator. 120 * @get_error_flags: Get the current error(s) for the regulator. 121 * @get_status: Return actual (not as-configured) status of regulator, as a 122 * REGULATOR_STATUS value (or negative errno) 123 * @get_optimum_mode: Get the most efficient operating mode for the regulator 124 * when running with the specified parameters. 125 * @set_load: Set the load for the regulator. 126 * 127 * @set_bypass: Set the regulator in bypass mode. 128 * @get_bypass: Get the regulator bypass mode state. 129 * 130 * @enable_time: Time taken for the regulator voltage output voltage to 131 * stabilise after being enabled, in microseconds. 132 * @set_ramp_delay: Set the ramp delay for the regulator. The driver should 133 * select ramp delay equal to or less than(closest) ramp_delay. 134 * @set_voltage_time: Time taken for the regulator voltage output voltage 135 * to stabilise after being set to a new value, in microseconds. 136 * The function receives the from and to voltage as input, it 137 * should return the worst case. 138 * @set_voltage_time_sel: Time taken for the regulator voltage output voltage 139 * to stabilise after being set to a new value, in microseconds. 140 * The function receives the from and to voltage selector as 141 * input, it should return the worst case. 142 * @set_soft_start: Enable soft start for the regulator. 143 * 144 * @set_suspend_voltage: Set the voltage for the regulator when the system 145 * is suspended. 146 * @set_suspend_enable: Mark the regulator as enabled when the system is 147 * suspended. 148 * @set_suspend_disable: Mark the regulator as disabled when the system is 149 * suspended. 150 * @set_suspend_mode: Set the operating mode for the regulator when the 151 * system is suspended. 152 * @resume: Resume operation of suspended regulator. 153 * @set_pull_down: Configure the regulator to pull down when the regulator 154 * is disabled. 155 * 156 * This struct describes regulator operations which can be implemented by 157 * regulator chip drivers. 158 */ 159 struct regulator_ops { 160 161 /* enumerate supported voltages */ 162 int (*list_voltage) (struct regulator_dev *, unsigned selector); 163 164 /* get/set regulator voltage */ 165 int (*set_voltage) (struct regulator_dev *, int min_uV, int max_uV, 166 unsigned *selector); 167 int (*map_voltage)(struct regulator_dev *, int min_uV, int max_uV); 168 int (*set_voltage_sel) (struct regulator_dev *, unsigned selector); 169 int (*get_voltage) (struct regulator_dev *); 170 int (*get_voltage_sel) (struct regulator_dev *); 171 172 /* get/set regulator current */ 173 int (*set_current_limit) (struct regulator_dev *, 174 int min_uA, int max_uA); 175 int (*get_current_limit) (struct regulator_dev *); 176 177 int (*set_input_current_limit) (struct regulator_dev *, int lim_uA); 178 int (*set_over_current_protection)(struct regulator_dev *, int lim_uA, 179 int severity, bool enable); 180 int (*set_over_voltage_protection)(struct regulator_dev *, int lim_uV, 181 int severity, bool enable); 182 int (*set_under_voltage_protection)(struct regulator_dev *, int lim_uV, 183 int severity, bool enable); 184 int (*set_thermal_protection)(struct regulator_dev *, int lim, 185 int severity, bool enable); 186 int (*set_active_discharge)(struct regulator_dev *, bool enable); 187 188 /* enable/disable regulator */ 189 int (*enable) (struct regulator_dev *); 190 int (*disable) (struct regulator_dev *); 191 int (*is_enabled) (struct regulator_dev *); 192 193 /* get/set regulator operating mode (defined in consumer.h) */ 194 int (*set_mode) (struct regulator_dev *, unsigned int mode); 195 unsigned int (*get_mode) (struct regulator_dev *); 196 197 /* retrieve current error flags on the regulator */ 198 int (*get_error_flags)(struct regulator_dev *, unsigned int *flags); 199 200 /* Time taken to enable or set voltage on the regulator */ 201 int (*enable_time) (struct regulator_dev *); 202 int (*set_ramp_delay) (struct regulator_dev *, int ramp_delay); 203 int (*set_voltage_time) (struct regulator_dev *, int old_uV, 204 int new_uV); 205 int (*set_voltage_time_sel) (struct regulator_dev *, 206 unsigned int old_selector, 207 unsigned int new_selector); 208 209 int (*set_soft_start) (struct regulator_dev *); 210 211 /* report regulator status ... most other accessors report 212 * control inputs, this reports results of combining inputs 213 * from Linux (and other sources) with the actual load. 214 * returns REGULATOR_STATUS_* or negative errno. 215 */ 216 int (*get_status)(struct regulator_dev *); 217 218 /* get most efficient regulator operating mode for load */ 219 unsigned int (*get_optimum_mode) (struct regulator_dev *, int input_uV, 220 int output_uV, int load_uA); 221 /* set the load on the regulator */ 222 int (*set_load)(struct regulator_dev *, int load_uA); 223 224 /* control and report on bypass mode */ 225 int (*set_bypass)(struct regulator_dev *dev, bool enable); 226 int (*get_bypass)(struct regulator_dev *dev, bool *enable); 227 228 /* the operations below are for configuration of regulator state when 229 * its parent PMIC enters a global STANDBY/HIBERNATE state */ 230 231 /* set regulator suspend voltage */ 232 int (*set_suspend_voltage) (struct regulator_dev *, int uV); 233 234 /* enable/disable regulator in suspend state */ 235 int (*set_suspend_enable) (struct regulator_dev *); 236 int (*set_suspend_disable) (struct regulator_dev *); 237 238 /* set regulator suspend operating mode (defined in consumer.h) */ 239 int (*set_suspend_mode) (struct regulator_dev *, unsigned int mode); 240 241 int (*resume)(struct regulator_dev *rdev); 242 243 int (*set_pull_down) (struct regulator_dev *); 244 }; 245 246 /* 247 * Regulators can either control voltage or current. 248 */ 249 enum regulator_type { 250 REGULATOR_VOLTAGE, 251 REGULATOR_CURRENT, 252 }; 253 254 /** 255 * struct regulator_desc - Static regulator descriptor 256 * 257 * Each regulator registered with the core is described with a 258 * structure of this type and a struct regulator_config. This 259 * structure contains the non-varying parts of the regulator 260 * description. 261 * 262 * @name: Identifying name for the regulator. 263 * @supply_name: Identifying the regulator supply 264 * @of_match: Name used to identify regulator in DT. 265 * @of_match_full_name: A flag to indicate that the of_match string, if 266 * present, should be matched against the node full_name. 267 * @regulators_node: Name of node containing regulator definitions in DT. 268 * @of_parse_cb: Optional callback called only if of_match is present. 269 * Will be called for each regulator parsed from DT, during 270 * init_data parsing. 271 * The regulator_config passed as argument to the callback will 272 * be a copy of config passed to regulator_register, valid only 273 * for this particular call. Callback may freely change the 274 * config but it cannot store it for later usage. 275 * Callback should return 0 on success or negative ERRNO 276 * indicating failure. 277 * @init_cb: Optional callback called after the parsing of init_data. 278 * Allows the regulator to perform runtime init if necessary, 279 * such as synching the regulator and the parsed constraints. 280 * Callback should return 0 on success or negative ERRNO 281 * indicating failure. 282 * @id: Numerical identifier for the regulator. 283 * @ops: Regulator operations table. 284 * @irq: Interrupt number for the regulator. 285 * @type: Indicates if the regulator is a voltage or current regulator. 286 * @owner: Module providing the regulator, used for refcounting. 287 * 288 * @continuous_voltage_range: Indicates if the regulator can set any 289 * voltage within constrains range. 290 * @n_voltages: Number of selectors available for ops.list_voltage(). 291 * @n_current_limits: Number of selectors available for current limits 292 * 293 * @min_uV: Voltage given by the lowest selector (if linear mapping) 294 * @uV_step: Voltage increase with each selector (if linear mapping) 295 * @linear_min_sel: Minimal selector for starting linear mapping 296 * @fixed_uV: Fixed voltage of rails. 297 * @ramp_delay: Time to settle down after voltage change (unit: uV/us) 298 * @min_dropout_uV: The minimum dropout voltage this regulator can handle 299 * @linear_ranges: A constant table of possible voltage ranges. 300 * @linear_range_selectors_bitfield: A constant table of voltage range 301 * selectors as bitfield values. If 302 * pickable ranges are used each range 303 * must have corresponding selector here. 304 * @n_linear_ranges: Number of entries in the @linear_ranges (and in 305 * linear_range_selectors_bitfield if used) table(s). 306 * @volt_table: Voltage mapping table (if table based mapping) 307 * @curr_table: Current limit mapping table (if table based mapping) 308 * 309 * @vsel_range_reg: Register for range selector when using pickable ranges 310 * and ``regulator_map_*_voltage_*_pickable`` functions. 311 * @vsel_range_mask: Mask for register bitfield used for range selector 312 * @range_applied_by_vsel: A flag to indicate that changes to vsel_range_reg 313 * are only effective after vsel_reg is written 314 * @vsel_reg: Register for selector when using ``regulator_map_*_voltage_*`` 315 * @vsel_mask: Mask for register bitfield used for selector 316 * @vsel_step: Specify the resolution of selector stepping when setting 317 * voltage. If 0, then no stepping is done (requested selector is 318 * set directly), if >0 then the regulator API will ramp the 319 * voltage up/down gradually each time increasing/decreasing the 320 * selector by the specified step value. 321 * @csel_reg: Register for current limit selector using regmap set_current_limit 322 * @csel_mask: Mask for register bitfield used for current limit selector 323 * @apply_reg: Register for initiate voltage change on the output when 324 * using regulator_set_voltage_sel_regmap 325 * @apply_bit: Register bitfield used for initiate voltage change on the 326 * output when using regulator_set_voltage_sel_regmap 327 * @enable_reg: Register for control when using regmap enable/disable ops 328 * @enable_mask: Mask for control when using regmap enable/disable ops 329 * @enable_val: Enabling value for control when using regmap enable/disable ops 330 * @disable_val: Disabling value for control when using regmap enable/disable ops 331 * @enable_is_inverted: A flag to indicate set enable_mask bits to disable 332 * when using regulator_enable_regmap and friends APIs. 333 * @bypass_reg: Register for control when using regmap set_bypass 334 * @bypass_mask: Mask for control when using regmap set_bypass 335 * @bypass_val_on: Enabling value for control when using regmap set_bypass 336 * @bypass_val_off: Disabling value for control when using regmap set_bypass 337 * @active_discharge_off: Enabling value for control when using regmap 338 * set_active_discharge 339 * @active_discharge_on: Disabling value for control when using regmap 340 * set_active_discharge 341 * @active_discharge_mask: Mask for control when using regmap 342 * set_active_discharge 343 * @active_discharge_reg: Register for control when using regmap 344 * set_active_discharge 345 * @soft_start_reg: Register for control when using regmap set_soft_start 346 * @soft_start_mask: Mask for control when using regmap set_soft_start 347 * @soft_start_val_on: Enabling value for control when using regmap 348 * set_soft_start 349 * @pull_down_reg: Register for control when using regmap set_pull_down 350 * @pull_down_mask: Mask for control when using regmap set_pull_down 351 * @pull_down_val_on: Enabling value for control when using regmap 352 * set_pull_down 353 * 354 * @ramp_reg: Register for controlling the regulator ramp-rate. 355 * @ramp_mask: Bitmask for the ramp-rate control register. 356 * @ramp_delay_table: Table for mapping the regulator ramp-rate values. Values 357 * should be given in units of V/S (uV/uS). See the 358 * regulator_set_ramp_delay_regmap(). 359 * @n_ramp_values: number of elements at @ramp_delay_table. 360 * 361 * @enable_time: Time taken for initial enable of regulator (in uS). 362 * @off_on_delay: guard time (in uS), before re-enabling a regulator 363 * 364 * @poll_enabled_time: The polling interval (in uS) to use while checking that 365 * the regulator was actually enabled. Max upto enable_time. 366 * 367 * @of_map_mode: Maps a hardware mode defined in a DeviceTree to a standard mode 368 */ 369 struct regulator_desc { 370 const char *name; 371 const char *supply_name; 372 const char *of_match; 373 bool of_match_full_name; 374 const char *regulators_node; 375 int (*of_parse_cb)(struct device_node *, 376 const struct regulator_desc *, 377 struct regulator_config *); 378 int (*init_cb)(struct regulator_dev *, 379 struct regulator_config *); 380 int id; 381 unsigned int continuous_voltage_range:1; 382 unsigned n_voltages; 383 unsigned int n_current_limits; 384 const struct regulator_ops *ops; 385 int irq; 386 enum regulator_type type; 387 struct module *owner; 388 389 unsigned int min_uV; 390 unsigned int uV_step; 391 unsigned int linear_min_sel; 392 int fixed_uV; 393 unsigned int ramp_delay; 394 int min_dropout_uV; 395 396 const struct linear_range *linear_ranges; 397 const unsigned int *linear_range_selectors_bitfield; 398 399 int n_linear_ranges; 400 401 const unsigned int *volt_table; 402 const unsigned int *curr_table; 403 404 unsigned int vsel_range_reg; 405 unsigned int vsel_range_mask; 406 bool range_applied_by_vsel; 407 unsigned int vsel_reg; 408 unsigned int vsel_mask; 409 unsigned int vsel_step; 410 unsigned int csel_reg; 411 unsigned int csel_mask; 412 unsigned int apply_reg; 413 unsigned int apply_bit; 414 unsigned int enable_reg; 415 unsigned int enable_mask; 416 unsigned int enable_val; 417 unsigned int disable_val; 418 bool enable_is_inverted; 419 unsigned int bypass_reg; 420 unsigned int bypass_mask; 421 unsigned int bypass_val_on; 422 unsigned int bypass_val_off; 423 unsigned int active_discharge_on; 424 unsigned int active_discharge_off; 425 unsigned int active_discharge_mask; 426 unsigned int active_discharge_reg; 427 unsigned int soft_start_reg; 428 unsigned int soft_start_mask; 429 unsigned int soft_start_val_on; 430 unsigned int pull_down_reg; 431 unsigned int pull_down_mask; 432 unsigned int pull_down_val_on; 433 unsigned int ramp_reg; 434 unsigned int ramp_mask; 435 const unsigned int *ramp_delay_table; 436 unsigned int n_ramp_values; 437 438 unsigned int enable_time; 439 440 unsigned int off_on_delay; 441 442 unsigned int poll_enabled_time; 443 444 unsigned int (*of_map_mode)(unsigned int mode); 445 }; 446 447 /** 448 * struct regulator_config - Dynamic regulator descriptor 449 * 450 * Each regulator registered with the core is described with a 451 * structure of this type and a struct regulator_desc. This structure 452 * contains the runtime variable parts of the regulator description. 453 * 454 * @dev: struct device for the regulator 455 * @init_data: platform provided init data, passed through by driver 456 * @driver_data: private regulator data 457 * @of_node: OpenFirmware node to parse for device tree bindings (may be 458 * NULL). 459 * @regmap: regmap to use for core regmap helpers if dev_get_regmap() is 460 * insufficient. 461 * @ena_gpiod: GPIO controlling regulator enable. 462 */ 463 struct regulator_config { 464 struct device *dev; 465 const struct regulator_init_data *init_data; 466 void *driver_data; 467 struct device_node *of_node; 468 struct regmap *regmap; 469 470 struct gpio_desc *ena_gpiod; 471 }; 472 473 /** 474 * struct regulator_err_state - regulator error/notification status 475 * 476 * @rdev: Regulator which status the struct indicates. 477 * @notifs: Events which have occurred on the regulator. 478 * @errors: Errors which are active on the regulator. 479 * @possible_errs: Errors which can be signaled (by given IRQ). 480 */ 481 struct regulator_err_state { 482 struct regulator_dev *rdev; 483 unsigned long notifs; 484 unsigned long errors; 485 int possible_errs; 486 }; 487 488 /** 489 * struct regulator_irq_data - regulator error/notification status data 490 * 491 * @states: Status structs for each of the associated regulators. 492 * @num_states: Amount of associated regulators. 493 * @data: Driver data pointer given at regulator_irq_desc. 494 * @opaque: Value storage for IC driver. Core does not update this. ICs 495 * may want to store status register value here at map_event and 496 * compare contents at 'renable' callback to see if new problems 497 * have been added to status. If that is the case it may be 498 * desirable to return REGULATOR_ERROR_CLEARED and not 499 * REGULATOR_ERROR_ON to allow IRQ fire again and to generate 500 * notifications also for the new issues. 501 * 502 * This structure is passed to 'map_event' and 'renable' callbacks for 503 * reporting regulator status to core. 504 */ 505 struct regulator_irq_data { 506 struct regulator_err_state *states; 507 int num_states; 508 void *data; 509 long opaque; 510 }; 511 512 /** 513 * struct regulator_irq_desc - notification sender for IRQ based events. 514 * 515 * @name: The visible name for the IRQ 516 * @fatal_cnt: If this IRQ is used to signal HW damaging condition it may be 517 * best to shut-down regulator(s) or reboot the SOC if error 518 * handling is repeatedly failing. If fatal_cnt is given the IRQ 519 * handling is aborted if it fails for fatal_cnt times and die() 520 * callback (if populated) is called. If die() is not populated 521 * poweroff for the system is attempted in order to prevent any 522 * further damage. 523 * @reread_ms: The time which is waited before attempting to re-read status 524 * at the worker if IC reading fails. Immediate re-read is done 525 * if time is not specified. 526 * @irq_off_ms: The time which IRQ is kept disabled before re-evaluating the 527 * status for devices which keep IRQ disabled for duration of the 528 * error. If this is not given the IRQ is left enabled and renable 529 * is not called. 530 * @skip_off: If set to true the IRQ handler will attempt to check if any of 531 * the associated regulators are enabled prior to taking other 532 * actions. If no regulators are enabled and this is set to true 533 * a spurious IRQ is assumed and IRQ_NONE is returned. 534 * @high_prio: Boolean to indicate that high priority WQ should be used. 535 * @data: Driver private data pointer which will be passed as such to 536 * the renable, map_event and die callbacks in regulator_irq_data. 537 * @die: Protection callback. If IC status reading or recovery actions 538 * fail fatal_cnt times this callback is called or system is 539 * powered off. This callback should implement a final protection 540 * attempt like disabling the regulator. If protection succeeded 541 * die() may return 0. If anything else is returned the core 542 * assumes final protection failed and attempts to perform a 543 * poweroff as a last resort. 544 * @map_event: Driver callback to map IRQ status into regulator devices with 545 * events / errors. NOTE: callback MUST initialize both the 546 * errors and notifs for all rdevs which it signals having 547 * active events as core does not clean the map data. 548 * REGULATOR_FAILED_RETRY can be returned to indicate that the 549 * status reading from IC failed. If this is repeated for 550 * fatal_cnt times the core will call die() callback or power-off 551 * the system as a last resort to protect the HW. 552 * @renable: Optional callback to check status (if HW supports that) before 553 * re-enabling IRQ. If implemented this should clear the error 554 * flags so that errors fetched by regulator_get_error_flags() 555 * are updated. If callback is not implemented then errors are 556 * assumed to be cleared and IRQ is re-enabled. 557 * REGULATOR_FAILED_RETRY can be returned to 558 * indicate that the status reading from IC failed. If this is 559 * repeated for 'fatal_cnt' times the core will call die() 560 * callback or if die() is not populated then attempt to power-off 561 * the system as a last resort to protect the HW. 562 * Returning zero indicates that the problem in HW has been solved 563 * and IRQ will be re-enabled. Returning REGULATOR_ERROR_ON 564 * indicates the error condition is still active and keeps IRQ 565 * disabled. Please note that returning REGULATOR_ERROR_ON does 566 * not retrigger evaluating what events are active or resending 567 * notifications. If this is needed you probably want to return 568 * zero and allow IRQ to retrigger causing events to be 569 * re-evaluated and re-sent. 570 * 571 * This structure is used for registering regulator IRQ notification helper. 572 */ 573 struct regulator_irq_desc { 574 const char *name; 575 int fatal_cnt; 576 int reread_ms; 577 int irq_off_ms; 578 bool skip_off; 579 bool high_prio; 580 void *data; 581 582 int (*die)(struct regulator_irq_data *rid); 583 int (*map_event)(int irq, struct regulator_irq_data *rid, 584 unsigned long *dev_mask); 585 int (*renable)(struct regulator_irq_data *rid); 586 }; 587 588 /* 589 * Return values for regulator IRQ helpers. 590 */ 591 enum { 592 REGULATOR_ERROR_CLEARED, 593 REGULATOR_FAILED_RETRY, 594 REGULATOR_ERROR_ON, 595 }; 596 597 /* 598 * struct coupling_desc 599 * 600 * Describes coupling of regulators. Each regulator should have 601 * at least a pointer to itself in coupled_rdevs array. 602 * When a new coupled regulator is resolved, n_resolved is 603 * incremented. 604 */ 605 struct coupling_desc { 606 struct regulator_dev **coupled_rdevs; 607 struct regulator_coupler *coupler; 608 int n_resolved; 609 int n_coupled; 610 }; 611 612 /* 613 * struct regulator_dev 614 * 615 * Voltage / Current regulator class device. One for each 616 * regulator. 617 * 618 * This should *not* be used directly by anything except the regulator 619 * core and notification injection (which should take the mutex and do 620 * no other direct access). 621 */ 622 struct regulator_dev { 623 const struct regulator_desc *desc; 624 int exclusive; 625 u32 use_count; 626 u32 open_count; 627 u32 bypass_count; 628 629 /* lists we belong to */ 630 struct list_head list; /* list of all regulators */ 631 632 /* lists we own */ 633 struct list_head consumer_list; /* consumers we supply */ 634 635 struct coupling_desc coupling_desc; 636 637 struct blocking_notifier_head notifier; 638 struct ww_mutex mutex; /* consumer lock */ 639 struct task_struct *mutex_owner; 640 int ref_cnt; 641 struct module *owner; 642 struct device dev; 643 struct device bdev; 644 struct regulation_constraints *constraints; 645 struct regulator *supply; /* for tree */ 646 const char *supply_name; 647 struct regmap *regmap; 648 649 struct delayed_work disable_work; 650 651 void *reg_data; /* regulator_dev data */ 652 653 struct dentry *debugfs; 654 655 struct regulator_enable_gpio *ena_pin; 656 unsigned int ena_gpio_state:1; 657 658 unsigned int constraints_pending:1; 659 unsigned int is_switch:1; 660 661 /* time when this regulator was disabled last time */ 662 ktime_t last_off; 663 int cached_err; 664 bool use_cached_err; 665 spinlock_t err_lock; 666 667 int pw_requested_mW; 668 669 /* regulator notification forwarding */ 670 struct notifier_block supply_fwd_nb; 671 }; 672 673 /* 674 * Convert error flags to corresponding notifications. 675 * 676 * Can be used by drivers which use the notification helpers to 677 * find out correct notification flags based on the error flags. Drivers 678 * can avoid storing both supported notification and error flags which 679 * may save few bytes. 680 */ 681 static inline int regulator_err2notif(int err) 682 { 683 switch (err) { 684 case REGULATOR_ERROR_UNDER_VOLTAGE: 685 return REGULATOR_EVENT_UNDER_VOLTAGE; 686 case REGULATOR_ERROR_OVER_CURRENT: 687 return REGULATOR_EVENT_OVER_CURRENT; 688 case REGULATOR_ERROR_REGULATION_OUT: 689 return REGULATOR_EVENT_REGULATION_OUT; 690 case REGULATOR_ERROR_FAIL: 691 return REGULATOR_EVENT_FAIL; 692 case REGULATOR_ERROR_OVER_TEMP: 693 return REGULATOR_EVENT_OVER_TEMP; 694 case REGULATOR_ERROR_UNDER_VOLTAGE_WARN: 695 return REGULATOR_EVENT_UNDER_VOLTAGE_WARN; 696 case REGULATOR_ERROR_OVER_CURRENT_WARN: 697 return REGULATOR_EVENT_OVER_CURRENT_WARN; 698 case REGULATOR_ERROR_OVER_VOLTAGE_WARN: 699 return REGULATOR_EVENT_OVER_VOLTAGE_WARN; 700 case REGULATOR_ERROR_OVER_TEMP_WARN: 701 return REGULATOR_EVENT_OVER_TEMP_WARN; 702 } 703 return 0; 704 } 705 706 707 struct regulator_dev * 708 regulator_register(struct device *dev, 709 const struct regulator_desc *regulator_desc, 710 const struct regulator_config *config); 711 struct regulator_dev * 712 devm_regulator_register(struct device *dev, 713 const struct regulator_desc *regulator_desc, 714 const struct regulator_config *config); 715 void regulator_unregister(struct regulator_dev *rdev); 716 717 int regulator_notifier_call_chain(struct regulator_dev *rdev, 718 unsigned long event, void *data); 719 void *devm_regulator_irq_helper(struct device *dev, 720 const struct regulator_irq_desc *d, int irq, 721 int irq_flags, int common_errs, 722 int *per_rdev_errs, struct regulator_dev **rdev, 723 int rdev_amount); 724 void *regulator_irq_helper(struct device *dev, 725 const struct regulator_irq_desc *d, int irq, 726 int irq_flags, int common_errs, int *per_rdev_errs, 727 struct regulator_dev **rdev, int rdev_amount); 728 void regulator_irq_helper_cancel(void **handle); 729 int regulator_irq_map_event_simple(int irq, struct regulator_irq_data *rid, 730 unsigned long *dev_mask); 731 732 void *rdev_get_drvdata(struct regulator_dev *rdev); 733 struct device *rdev_get_dev(struct regulator_dev *rdev); 734 struct regmap *rdev_get_regmap(struct regulator_dev *rdev); 735 int rdev_get_id(struct regulator_dev *rdev); 736 737 int regulator_mode_to_status(unsigned int); 738 739 int regulator_list_voltage_linear(struct regulator_dev *rdev, 740 unsigned int selector); 741 int regulator_list_voltage_pickable_linear_range(struct regulator_dev *rdev, 742 unsigned int selector); 743 int regulator_list_voltage_linear_range(struct regulator_dev *rdev, 744 unsigned int selector); 745 int regulator_list_voltage_table(struct regulator_dev *rdev, 746 unsigned int selector); 747 int regulator_map_voltage_linear(struct regulator_dev *rdev, 748 int min_uV, int max_uV); 749 int regulator_map_voltage_pickable_linear_range(struct regulator_dev *rdev, 750 int min_uV, int max_uV); 751 int regulator_map_voltage_linear_range(struct regulator_dev *rdev, 752 int min_uV, int max_uV); 753 int regulator_map_voltage_iterate(struct regulator_dev *rdev, 754 int min_uV, int max_uV); 755 int regulator_map_voltage_ascend(struct regulator_dev *rdev, 756 int min_uV, int max_uV); 757 int regulator_get_voltage_sel_pickable_regmap(struct regulator_dev *rdev); 758 int regulator_set_voltage_sel_pickable_regmap(struct regulator_dev *rdev, 759 unsigned int sel); 760 int regulator_get_voltage_sel_regmap(struct regulator_dev *rdev); 761 int regulator_set_voltage_sel_regmap(struct regulator_dev *rdev, unsigned sel); 762 int regulator_is_enabled_regmap(struct regulator_dev *rdev); 763 int regulator_enable_regmap(struct regulator_dev *rdev); 764 int regulator_disable_regmap(struct regulator_dev *rdev); 765 int regulator_set_voltage_time_sel(struct regulator_dev *rdev, 766 unsigned int old_selector, 767 unsigned int new_selector); 768 int regulator_set_bypass_regmap(struct regulator_dev *rdev, bool enable); 769 int regulator_get_bypass_regmap(struct regulator_dev *rdev, bool *enable); 770 int regulator_set_soft_start_regmap(struct regulator_dev *rdev); 771 int regulator_set_pull_down_regmap(struct regulator_dev *rdev); 772 773 int regulator_set_active_discharge_regmap(struct regulator_dev *rdev, 774 bool enable); 775 int regulator_set_current_limit_regmap(struct regulator_dev *rdev, 776 int min_uA, int max_uA); 777 int regulator_get_current_limit_regmap(struct regulator_dev *rdev); 778 void *regulator_get_init_drvdata(struct regulator_init_data *reg_init_data); 779 int regulator_find_closest_bigger(unsigned int target, const unsigned int *table, 780 unsigned int num_sel, unsigned int *sel); 781 int regulator_set_ramp_delay_regmap(struct regulator_dev *rdev, int ramp_delay); 782 int regulator_sync_voltage_rdev(struct regulator_dev *rdev); 783 784 /* 785 * Helper functions intended to be used by regulator drivers prior registering 786 * their regulators. 787 */ 788 int regulator_desc_list_voltage_linear_range(const struct regulator_desc *desc, 789 unsigned int selector); 790 791 int regulator_desc_list_voltage_linear(const struct regulator_desc *desc, 792 unsigned int selector); 793 794 #ifdef CONFIG_REGULATOR 795 const char *rdev_get_name(struct regulator_dev *rdev); 796 #else 797 static inline const char *rdev_get_name(struct regulator_dev *rdev) 798 { 799 return NULL; 800 } 801 #endif 802 803 #endif 804