1 /* SPDX-License-Identifier: GPL-2.0-only */ 2 /* 3 * driver.h -- SoC Regulator driver support. 4 * 5 * Copyright (C) 2007, 2008 Wolfson Microelectronics PLC. 6 * 7 * Author: Liam Girdwood <lrg@slimlogic.co.uk> 8 * 9 * Regulator Driver Interface. 10 */ 11 12 #ifndef __LINUX_REGULATOR_DRIVER_H_ 13 #define __LINUX_REGULATOR_DRIVER_H_ 14 15 #include <linux/device.h> 16 #include <linux/linear_range.h> 17 #include <linux/notifier.h> 18 #include <linux/regulator/consumer.h> 19 #include <linux/ww_mutex.h> 20 21 struct gpio_desc; 22 struct regmap; 23 struct regulator_dev; 24 struct regulator_config; 25 struct regulator_init_data; 26 struct regulator_enable_gpio; 27 28 enum regulator_status { 29 REGULATOR_STATUS_OFF, 30 REGULATOR_STATUS_ON, 31 REGULATOR_STATUS_ERROR, 32 /* fast/normal/idle/standby are flavors of "on" */ 33 REGULATOR_STATUS_FAST, 34 REGULATOR_STATUS_NORMAL, 35 REGULATOR_STATUS_IDLE, 36 REGULATOR_STATUS_STANDBY, 37 /* The regulator is enabled but not regulating */ 38 REGULATOR_STATUS_BYPASS, 39 /* in case that any other status doesn't apply */ 40 REGULATOR_STATUS_UNDEFINED, 41 }; 42 43 enum regulator_detection_severity { 44 /* Hardware shut down voltage outputs if condition is detected */ 45 REGULATOR_SEVERITY_PROT, 46 /* Hardware is probably damaged/inoperable */ 47 REGULATOR_SEVERITY_ERR, 48 /* Hardware is still recoverable but recovery action must be taken */ 49 REGULATOR_SEVERITY_WARN, 50 }; 51 52 /* Initialize struct linear_range for regulators */ 53 #define REGULATOR_LINEAR_RANGE(_min_uV, _min_sel, _max_sel, _step_uV) \ 54 LINEAR_RANGE(_min_uV, _min_sel, _max_sel, _step_uV) 55 56 /** 57 * struct regulator_ops - regulator operations. 58 * 59 * @enable: Configure the regulator as enabled. 60 * @disable: Configure the regulator as disabled. 61 * @is_enabled: Return 1 if the regulator is enabled, 0 if not. 62 * May also return negative errno. 63 * 64 * @set_voltage: Set the voltage for the regulator within the range specified. 65 * The driver should select the voltage closest to min_uV. 66 * @set_voltage_sel: Set the voltage for the regulator using the specified 67 * selector. 68 * @map_voltage: Convert a voltage into a selector 69 * @get_voltage: Return the currently configured voltage for the regulator; 70 * return -ENOTRECOVERABLE if regulator can't be read at 71 * bootup and hasn't been set yet. 72 * @get_voltage_sel: Return the currently configured voltage selector for the 73 * regulator; return -ENOTRECOVERABLE if regulator can't 74 * be read at bootup and hasn't been set yet. 75 * @list_voltage: Return one of the supported voltages, in microvolts; zero 76 * if the selector indicates a voltage that is unusable on this system; 77 * or negative errno. Selectors range from zero to one less than 78 * regulator_desc.n_voltages. Voltages may be reported in any order. 79 * 80 * @set_current_limit: Configure a limit for a current-limited regulator. 81 * The driver should select the current closest to max_uA. 82 * @get_current_limit: Get the configured limit for a current-limited regulator. 83 * @set_input_current_limit: Configure an input limit. 84 * 85 * @set_over_current_protection: Support enabling of and setting limits for over 86 * current situation detection. Detection can be configured for three 87 * levels of severity. 88 * 89 * - REGULATOR_SEVERITY_PROT should automatically shut down the regulator(s). 90 * 91 * - REGULATOR_SEVERITY_ERR should indicate that over-current situation is 92 * caused by an unrecoverable error but HW does not perform 93 * automatic shut down. 94 * 95 * - REGULATOR_SEVERITY_WARN should indicate situation where hardware is 96 * still believed to not be damaged but that a board sepcific 97 * recovery action is needed. If lim_uA is 0 the limit should not 98 * be changed but the detection should just be enabled/disabled as 99 * is requested. 100 * 101 * @set_over_voltage_protection: Support enabling of and setting limits for over 102 * voltage situation detection. Detection can be configured for same 103 * severities as over current protection. Units of uV. 104 * @set_under_voltage_protection: Support enabling of and setting limits for 105 * under voltage situation detection. Detection can be configured for same 106 * severities as over current protection. Units of uV. 107 * @set_thermal_protection: Support enabling of and setting limits for over 108 * temperature situation detection.Detection can be configured for same 109 * severities as over current protection. Units of degree Kelvin. 110 * 111 * @set_active_discharge: Set active discharge enable/disable of regulators. 112 * 113 * @set_mode: Set the configured operating mode for the regulator. 114 * @get_mode: Get the configured operating mode for the regulator. 115 * @get_error_flags: Get the current error(s) for the regulator. 116 * @get_status: Return actual (not as-configured) status of regulator, as a 117 * REGULATOR_STATUS value (or negative errno) 118 * @get_optimum_mode: Get the most efficient operating mode for the regulator 119 * when running with the specified parameters. 120 * @set_load: Set the load for the regulator. 121 * 122 * @set_bypass: Set the regulator in bypass mode. 123 * @get_bypass: Get the regulator bypass mode state. 124 * 125 * @enable_time: Time taken for the regulator voltage output voltage to 126 * stabilise after being enabled, in microseconds. 127 * @set_ramp_delay: Set the ramp delay for the regulator. The driver should 128 * select ramp delay equal to or less than(closest) ramp_delay. 129 * @set_voltage_time: Time taken for the regulator voltage output voltage 130 * to stabilise after being set to a new value, in microseconds. 131 * The function receives the from and to voltage as input, it 132 * should return the worst case. 133 * @set_voltage_time_sel: Time taken for the regulator voltage output voltage 134 * to stabilise after being set to a new value, in microseconds. 135 * The function receives the from and to voltage selector as 136 * input, it should return the worst case. 137 * @set_soft_start: Enable soft start for the regulator. 138 * 139 * @set_suspend_voltage: Set the voltage for the regulator when the system 140 * is suspended. 141 * @set_suspend_enable: Mark the regulator as enabled when the system is 142 * suspended. 143 * @set_suspend_disable: Mark the regulator as disabled when the system is 144 * suspended. 145 * @set_suspend_mode: Set the operating mode for the regulator when the 146 * system is suspended. 147 * @resume: Resume operation of suspended regulator. 148 * @set_pull_down: Configure the regulator to pull down when the regulator 149 * is disabled. 150 * 151 * This struct describes regulator operations which can be implemented by 152 * regulator chip drivers. 153 */ 154 struct regulator_ops { 155 156 /* enumerate supported voltages */ 157 int (*list_voltage) (struct regulator_dev *, unsigned selector); 158 159 /* get/set regulator voltage */ 160 int (*set_voltage) (struct regulator_dev *, int min_uV, int max_uV, 161 unsigned *selector); 162 int (*map_voltage)(struct regulator_dev *, int min_uV, int max_uV); 163 int (*set_voltage_sel) (struct regulator_dev *, unsigned selector); 164 int (*get_voltage) (struct regulator_dev *); 165 int (*get_voltage_sel) (struct regulator_dev *); 166 167 /* get/set regulator current */ 168 int (*set_current_limit) (struct regulator_dev *, 169 int min_uA, int max_uA); 170 int (*get_current_limit) (struct regulator_dev *); 171 172 int (*set_input_current_limit) (struct regulator_dev *, int lim_uA); 173 int (*set_over_current_protection)(struct regulator_dev *, int lim_uA, 174 int severity, bool enable); 175 int (*set_over_voltage_protection)(struct regulator_dev *, int lim_uV, 176 int severity, bool enable); 177 int (*set_under_voltage_protection)(struct regulator_dev *, int lim_uV, 178 int severity, bool enable); 179 int (*set_thermal_protection)(struct regulator_dev *, int lim, 180 int severity, bool enable); 181 int (*set_active_discharge)(struct regulator_dev *, bool enable); 182 183 /* enable/disable regulator */ 184 int (*enable) (struct regulator_dev *); 185 int (*disable) (struct regulator_dev *); 186 int (*is_enabled) (struct regulator_dev *); 187 188 /* get/set regulator operating mode (defined in consumer.h) */ 189 int (*set_mode) (struct regulator_dev *, unsigned int mode); 190 unsigned int (*get_mode) (struct regulator_dev *); 191 192 /* retrieve current error flags on the regulator */ 193 int (*get_error_flags)(struct regulator_dev *, unsigned int *flags); 194 195 /* Time taken to enable or set voltage on the regulator */ 196 int (*enable_time) (struct regulator_dev *); 197 int (*set_ramp_delay) (struct regulator_dev *, int ramp_delay); 198 int (*set_voltage_time) (struct regulator_dev *, int old_uV, 199 int new_uV); 200 int (*set_voltage_time_sel) (struct regulator_dev *, 201 unsigned int old_selector, 202 unsigned int new_selector); 203 204 int (*set_soft_start) (struct regulator_dev *); 205 206 /* report regulator status ... most other accessors report 207 * control inputs, this reports results of combining inputs 208 * from Linux (and other sources) with the actual load. 209 * returns REGULATOR_STATUS_* or negative errno. 210 */ 211 int (*get_status)(struct regulator_dev *); 212 213 /* get most efficient regulator operating mode for load */ 214 unsigned int (*get_optimum_mode) (struct regulator_dev *, int input_uV, 215 int output_uV, int load_uA); 216 /* set the load on the regulator */ 217 int (*set_load)(struct regulator_dev *, int load_uA); 218 219 /* control and report on bypass mode */ 220 int (*set_bypass)(struct regulator_dev *dev, bool enable); 221 int (*get_bypass)(struct regulator_dev *dev, bool *enable); 222 223 /* the operations below are for configuration of regulator state when 224 * its parent PMIC enters a global STANDBY/HIBERNATE state */ 225 226 /* set regulator suspend voltage */ 227 int (*set_suspend_voltage) (struct regulator_dev *, int uV); 228 229 /* enable/disable regulator in suspend state */ 230 int (*set_suspend_enable) (struct regulator_dev *); 231 int (*set_suspend_disable) (struct regulator_dev *); 232 233 /* set regulator suspend operating mode (defined in consumer.h) */ 234 int (*set_suspend_mode) (struct regulator_dev *, unsigned int mode); 235 236 int (*resume)(struct regulator_dev *rdev); 237 238 int (*set_pull_down) (struct regulator_dev *); 239 }; 240 241 /* 242 * Regulators can either control voltage or current. 243 */ 244 enum regulator_type { 245 REGULATOR_VOLTAGE, 246 REGULATOR_CURRENT, 247 }; 248 249 /** 250 * struct regulator_desc - Static regulator descriptor 251 * 252 * Each regulator registered with the core is described with a 253 * structure of this type and a struct regulator_config. This 254 * structure contains the non-varying parts of the regulator 255 * description. 256 * 257 * @name: Identifying name for the regulator. 258 * @supply_name: Identifying the regulator supply 259 * @of_match: Name used to identify regulator in DT. 260 * @of_match_full_name: A flag to indicate that the of_match string, if 261 * present, should be matched against the node full_name. 262 * @regulators_node: Name of node containing regulator definitions in DT. 263 * @of_parse_cb: Optional callback called only if of_match is present. 264 * Will be called for each regulator parsed from DT, during 265 * init_data parsing. 266 * The regulator_config passed as argument to the callback will 267 * be a copy of config passed to regulator_register, valid only 268 * for this particular call. Callback may freely change the 269 * config but it cannot store it for later usage. 270 * Callback should return 0 on success or negative ERRNO 271 * indicating failure. 272 * @id: Numerical identifier for the regulator. 273 * @ops: Regulator operations table. 274 * @irq: Interrupt number for the regulator. 275 * @type: Indicates if the regulator is a voltage or current regulator. 276 * @owner: Module providing the regulator, used for refcounting. 277 * 278 * @continuous_voltage_range: Indicates if the regulator can set any 279 * voltage within constrains range. 280 * @n_voltages: Number of selectors available for ops.list_voltage(). 281 * @n_current_limits: Number of selectors available for current limits 282 * 283 * @min_uV: Voltage given by the lowest selector (if linear mapping) 284 * @uV_step: Voltage increase with each selector (if linear mapping) 285 * @linear_min_sel: Minimal selector for starting linear mapping 286 * @fixed_uV: Fixed voltage of rails. 287 * @ramp_delay: Time to settle down after voltage change (unit: uV/us) 288 * @min_dropout_uV: The minimum dropout voltage this regulator can handle 289 * @linear_ranges: A constant table of possible voltage ranges. 290 * @linear_range_selectors_bitfield: A constant table of voltage range 291 * selectors as bitfield values. If 292 * pickable ranges are used each range 293 * must have corresponding selector here. 294 * @n_linear_ranges: Number of entries in the @linear_ranges (and in 295 * linear_range_selectors_bitfield if used) table(s). 296 * @volt_table: Voltage mapping table (if table based mapping) 297 * @curr_table: Current limit mapping table (if table based mapping) 298 * 299 * @vsel_range_reg: Register for range selector when using pickable ranges 300 * and ``regulator_map_*_voltage_*_pickable`` functions. 301 * @vsel_range_mask: Mask for register bitfield used for range selector 302 * @vsel_reg: Register for selector when using ``regulator_map_*_voltage_*`` 303 * @vsel_mask: Mask for register bitfield used for selector 304 * @vsel_step: Specify the resolution of selector stepping when setting 305 * voltage. If 0, then no stepping is done (requested selector is 306 * set directly), if >0 then the regulator API will ramp the 307 * voltage up/down gradually each time increasing/decreasing the 308 * selector by the specified step value. 309 * @csel_reg: Register for current limit selector using regmap set_current_limit 310 * @csel_mask: Mask for register bitfield used for current limit selector 311 * @apply_reg: Register for initiate voltage change on the output when 312 * using regulator_set_voltage_sel_regmap 313 * @apply_bit: Register bitfield used for initiate voltage change on the 314 * output when using regulator_set_voltage_sel_regmap 315 * @enable_reg: Register for control when using regmap enable/disable ops 316 * @enable_mask: Mask for control when using regmap enable/disable ops 317 * @enable_val: Enabling value for control when using regmap enable/disable ops 318 * @disable_val: Disabling value for control when using regmap enable/disable ops 319 * @enable_is_inverted: A flag to indicate set enable_mask bits to disable 320 * when using regulator_enable_regmap and friends APIs. 321 * @bypass_reg: Register for control when using regmap set_bypass 322 * @bypass_mask: Mask for control when using regmap set_bypass 323 * @bypass_val_on: Enabling value for control when using regmap set_bypass 324 * @bypass_val_off: Disabling value for control when using regmap set_bypass 325 * @active_discharge_off: Enabling value for control when using regmap 326 * set_active_discharge 327 * @active_discharge_on: Disabling value for control when using regmap 328 * set_active_discharge 329 * @active_discharge_mask: Mask for control when using regmap 330 * set_active_discharge 331 * @active_discharge_reg: Register for control when using regmap 332 * set_active_discharge 333 * @soft_start_reg: Register for control when using regmap set_soft_start 334 * @soft_start_mask: Mask for control when using regmap set_soft_start 335 * @soft_start_val_on: Enabling value for control when using regmap 336 * set_soft_start 337 * @pull_down_reg: Register for control when using regmap set_pull_down 338 * @pull_down_mask: Mask for control when using regmap set_pull_down 339 * @pull_down_val_on: Enabling value for control when using regmap 340 * set_pull_down 341 * 342 * @ramp_reg: Register for controlling the regulator ramp-rate. 343 * @ramp_mask: Bitmask for the ramp-rate control register. 344 * @ramp_delay_table: Table for mapping the regulator ramp-rate values. Values 345 * should be given in units of V/S (uV/uS). See the 346 * regulator_set_ramp_delay_regmap(). 347 * @n_ramp_values: number of elements at @ramp_delay_table. 348 * 349 * @enable_time: Time taken for initial enable of regulator (in uS). 350 * @off_on_delay: guard time (in uS), before re-enabling a regulator 351 * 352 * @poll_enabled_time: The polling interval (in uS) to use while checking that 353 * the regulator was actually enabled. Max upto enable_time. 354 * 355 * @of_map_mode: Maps a hardware mode defined in a DeviceTree to a standard mode 356 */ 357 struct regulator_desc { 358 const char *name; 359 const char *supply_name; 360 const char *of_match; 361 bool of_match_full_name; 362 const char *regulators_node; 363 int (*of_parse_cb)(struct device_node *, 364 const struct regulator_desc *, 365 struct regulator_config *); 366 int id; 367 unsigned int continuous_voltage_range:1; 368 unsigned n_voltages; 369 unsigned int n_current_limits; 370 const struct regulator_ops *ops; 371 int irq; 372 enum regulator_type type; 373 struct module *owner; 374 375 unsigned int min_uV; 376 unsigned int uV_step; 377 unsigned int linear_min_sel; 378 int fixed_uV; 379 unsigned int ramp_delay; 380 int min_dropout_uV; 381 382 const struct linear_range *linear_ranges; 383 const unsigned int *linear_range_selectors_bitfield; 384 385 int n_linear_ranges; 386 387 const unsigned int *volt_table; 388 const unsigned int *curr_table; 389 390 unsigned int vsel_range_reg; 391 unsigned int vsel_range_mask; 392 unsigned int vsel_reg; 393 unsigned int vsel_mask; 394 unsigned int vsel_step; 395 unsigned int csel_reg; 396 unsigned int csel_mask; 397 unsigned int apply_reg; 398 unsigned int apply_bit; 399 unsigned int enable_reg; 400 unsigned int enable_mask; 401 unsigned int enable_val; 402 unsigned int disable_val; 403 bool enable_is_inverted; 404 unsigned int bypass_reg; 405 unsigned int bypass_mask; 406 unsigned int bypass_val_on; 407 unsigned int bypass_val_off; 408 unsigned int active_discharge_on; 409 unsigned int active_discharge_off; 410 unsigned int active_discharge_mask; 411 unsigned int active_discharge_reg; 412 unsigned int soft_start_reg; 413 unsigned int soft_start_mask; 414 unsigned int soft_start_val_on; 415 unsigned int pull_down_reg; 416 unsigned int pull_down_mask; 417 unsigned int pull_down_val_on; 418 unsigned int ramp_reg; 419 unsigned int ramp_mask; 420 const unsigned int *ramp_delay_table; 421 unsigned int n_ramp_values; 422 423 unsigned int enable_time; 424 425 unsigned int off_on_delay; 426 427 unsigned int poll_enabled_time; 428 429 unsigned int (*of_map_mode)(unsigned int mode); 430 }; 431 432 /** 433 * struct regulator_config - Dynamic regulator descriptor 434 * 435 * Each regulator registered with the core is described with a 436 * structure of this type and a struct regulator_desc. This structure 437 * contains the runtime variable parts of the regulator description. 438 * 439 * @dev: struct device for the regulator 440 * @init_data: platform provided init data, passed through by driver 441 * @driver_data: private regulator data 442 * @of_node: OpenFirmware node to parse for device tree bindings (may be 443 * NULL). 444 * @regmap: regmap to use for core regmap helpers if dev_get_regmap() is 445 * insufficient. 446 * @ena_gpiod: GPIO controlling regulator enable. 447 */ 448 struct regulator_config { 449 struct device *dev; 450 const struct regulator_init_data *init_data; 451 void *driver_data; 452 struct device_node *of_node; 453 struct regmap *regmap; 454 455 struct gpio_desc *ena_gpiod; 456 }; 457 458 /** 459 * struct regulator_err_state - regulator error/notification status 460 * 461 * @rdev: Regulator which status the struct indicates. 462 * @notifs: Events which have occurred on the regulator. 463 * @errors: Errors which are active on the regulator. 464 * @possible_errs: Errors which can be signaled (by given IRQ). 465 */ 466 struct regulator_err_state { 467 struct regulator_dev *rdev; 468 unsigned long notifs; 469 unsigned long errors; 470 int possible_errs; 471 }; 472 473 /** 474 * struct regulator_irq_data - regulator error/notification status data 475 * 476 * @states: Status structs for each of the associated regulators. 477 * @num_states: Amount of associated regulators. 478 * @data: Driver data pointer given at regulator_irq_desc. 479 * @opaque: Value storage for IC driver. Core does not update this. ICs 480 * may want to store status register value here at map_event and 481 * compare contents at 'renable' callback to see if new problems 482 * have been added to status. If that is the case it may be 483 * desirable to return REGULATOR_ERROR_CLEARED and not 484 * REGULATOR_ERROR_ON to allow IRQ fire again and to generate 485 * notifications also for the new issues. 486 * 487 * This structure is passed to 'map_event' and 'renable' callbacks for 488 * reporting regulator status to core. 489 */ 490 struct regulator_irq_data { 491 struct regulator_err_state *states; 492 int num_states; 493 void *data; 494 long opaque; 495 }; 496 497 /** 498 * struct regulator_irq_desc - notification sender for IRQ based events. 499 * 500 * @name: The visible name for the IRQ 501 * @fatal_cnt: If this IRQ is used to signal HW damaging condition it may be 502 * best to shut-down regulator(s) or reboot the SOC if error 503 * handling is repeatedly failing. If fatal_cnt is given the IRQ 504 * handling is aborted if it fails for fatal_cnt times and die() 505 * callback (if populated) is called. If die() is not populated 506 * poweroff for the system is attempted in order to prevent any 507 * further damage. 508 * @reread_ms: The time which is waited before attempting to re-read status 509 * at the worker if IC reading fails. Immediate re-read is done 510 * if time is not specified. 511 * @irq_off_ms: The time which IRQ is kept disabled before re-evaluating the 512 * status for devices which keep IRQ disabled for duration of the 513 * error. If this is not given the IRQ is left enabled and renable 514 * is not called. 515 * @skip_off: If set to true the IRQ handler will attempt to check if any of 516 * the associated regulators are enabled prior to taking other 517 * actions. If no regulators are enabled and this is set to true 518 * a spurious IRQ is assumed and IRQ_NONE is returned. 519 * @high_prio: Boolean to indicate that high priority WQ should be used. 520 * @data: Driver private data pointer which will be passed as such to 521 * the renable, map_event and die callbacks in regulator_irq_data. 522 * @die: Protection callback. If IC status reading or recovery actions 523 * fail fatal_cnt times this callback is called or system is 524 * powered off. This callback should implement a final protection 525 * attempt like disabling the regulator. If protection succeeded 526 * die() may return 0. If anything else is returned the core 527 * assumes final protection failed and attempts to perform a 528 * poweroff as a last resort. 529 * @map_event: Driver callback to map IRQ status into regulator devices with 530 * events / errors. NOTE: callback MUST initialize both the 531 * errors and notifs for all rdevs which it signals having 532 * active events as core does not clean the map data. 533 * REGULATOR_FAILED_RETRY can be returned to indicate that the 534 * status reading from IC failed. If this is repeated for 535 * fatal_cnt times the core will call die() callback or power-off 536 * the system as a last resort to protect the HW. 537 * @renable: Optional callback to check status (if HW supports that) before 538 * re-enabling IRQ. If implemented this should clear the error 539 * flags so that errors fetched by regulator_get_error_flags() 540 * are updated. If callback is not implemented then errors are 541 * assumed to be cleared and IRQ is re-enabled. 542 * REGULATOR_FAILED_RETRY can be returned to 543 * indicate that the status reading from IC failed. If this is 544 * repeated for 'fatal_cnt' times the core will call die() 545 * callback or if die() is not populated then attempt to power-off 546 * the system as a last resort to protect the HW. 547 * Returning zero indicates that the problem in HW has been solved 548 * and IRQ will be re-enabled. Returning REGULATOR_ERROR_ON 549 * indicates the error condition is still active and keeps IRQ 550 * disabled. Please note that returning REGULATOR_ERROR_ON does 551 * not retrigger evaluating what events are active or resending 552 * notifications. If this is needed you probably want to return 553 * zero and allow IRQ to retrigger causing events to be 554 * re-evaluated and re-sent. 555 * 556 * This structure is used for registering regulator IRQ notification helper. 557 */ 558 struct regulator_irq_desc { 559 const char *name; 560 int fatal_cnt; 561 int reread_ms; 562 int irq_off_ms; 563 bool skip_off; 564 bool high_prio; 565 void *data; 566 567 int (*die)(struct regulator_irq_data *rid); 568 int (*map_event)(int irq, struct regulator_irq_data *rid, 569 unsigned long *dev_mask); 570 int (*renable)(struct regulator_irq_data *rid); 571 }; 572 573 /* 574 * Return values for regulator IRQ helpers. 575 */ 576 enum { 577 REGULATOR_ERROR_CLEARED, 578 REGULATOR_FAILED_RETRY, 579 REGULATOR_ERROR_ON, 580 }; 581 582 /* 583 * struct coupling_desc 584 * 585 * Describes coupling of regulators. Each regulator should have 586 * at least a pointer to itself in coupled_rdevs array. 587 * When a new coupled regulator is resolved, n_resolved is 588 * incremented. 589 */ 590 struct coupling_desc { 591 struct regulator_dev **coupled_rdevs; 592 struct regulator_coupler *coupler; 593 int n_resolved; 594 int n_coupled; 595 }; 596 597 /* 598 * struct regulator_dev 599 * 600 * Voltage / Current regulator class device. One for each 601 * regulator. 602 * 603 * This should *not* be used directly by anything except the regulator 604 * core and notification injection (which should take the mutex and do 605 * no other direct access). 606 */ 607 struct regulator_dev { 608 const struct regulator_desc *desc; 609 int exclusive; 610 u32 use_count; 611 u32 open_count; 612 u32 bypass_count; 613 614 /* lists we belong to */ 615 struct list_head list; /* list of all regulators */ 616 617 /* lists we own */ 618 struct list_head consumer_list; /* consumers we supply */ 619 620 struct coupling_desc coupling_desc; 621 622 struct blocking_notifier_head notifier; 623 struct ww_mutex mutex; /* consumer lock */ 624 struct task_struct *mutex_owner; 625 int ref_cnt; 626 struct module *owner; 627 struct device dev; 628 struct regulation_constraints *constraints; 629 struct regulator *supply; /* for tree */ 630 const char *supply_name; 631 struct regmap *regmap; 632 633 struct delayed_work disable_work; 634 635 void *reg_data; /* regulator_dev data */ 636 637 struct dentry *debugfs; 638 639 struct regulator_enable_gpio *ena_pin; 640 unsigned int ena_gpio_state:1; 641 642 unsigned int is_switch:1; 643 644 /* time when this regulator was disabled last time */ 645 ktime_t last_off; 646 int cached_err; 647 bool use_cached_err; 648 spinlock_t err_lock; 649 }; 650 651 /* 652 * Convert error flags to corresponding notifications. 653 * 654 * Can be used by drivers which use the notification helpers to 655 * find out correct notification flags based on the error flags. Drivers 656 * can avoid storing both supported notification and error flags which 657 * may save few bytes. 658 */ 659 static inline int regulator_err2notif(int err) 660 { 661 switch (err) { 662 case REGULATOR_ERROR_UNDER_VOLTAGE: 663 return REGULATOR_EVENT_UNDER_VOLTAGE; 664 case REGULATOR_ERROR_OVER_CURRENT: 665 return REGULATOR_EVENT_OVER_CURRENT; 666 case REGULATOR_ERROR_REGULATION_OUT: 667 return REGULATOR_EVENT_REGULATION_OUT; 668 case REGULATOR_ERROR_FAIL: 669 return REGULATOR_EVENT_FAIL; 670 case REGULATOR_ERROR_OVER_TEMP: 671 return REGULATOR_EVENT_OVER_TEMP; 672 case REGULATOR_ERROR_UNDER_VOLTAGE_WARN: 673 return REGULATOR_EVENT_UNDER_VOLTAGE_WARN; 674 case REGULATOR_ERROR_OVER_CURRENT_WARN: 675 return REGULATOR_EVENT_OVER_CURRENT_WARN; 676 case REGULATOR_ERROR_OVER_VOLTAGE_WARN: 677 return REGULATOR_EVENT_OVER_VOLTAGE_WARN; 678 case REGULATOR_ERROR_OVER_TEMP_WARN: 679 return REGULATOR_EVENT_OVER_TEMP_WARN; 680 } 681 return 0; 682 } 683 684 685 struct regulator_dev * 686 regulator_register(struct device *dev, 687 const struct regulator_desc *regulator_desc, 688 const struct regulator_config *config); 689 struct regulator_dev * 690 devm_regulator_register(struct device *dev, 691 const struct regulator_desc *regulator_desc, 692 const struct regulator_config *config); 693 void regulator_unregister(struct regulator_dev *rdev); 694 695 int regulator_notifier_call_chain(struct regulator_dev *rdev, 696 unsigned long event, void *data); 697 void *devm_regulator_irq_helper(struct device *dev, 698 const struct regulator_irq_desc *d, int irq, 699 int irq_flags, int common_errs, 700 int *per_rdev_errs, struct regulator_dev **rdev, 701 int rdev_amount); 702 void *regulator_irq_helper(struct device *dev, 703 const struct regulator_irq_desc *d, int irq, 704 int irq_flags, int common_errs, int *per_rdev_errs, 705 struct regulator_dev **rdev, int rdev_amount); 706 void regulator_irq_helper_cancel(void **handle); 707 int regulator_irq_map_event_simple(int irq, struct regulator_irq_data *rid, 708 unsigned long *dev_mask); 709 710 void *rdev_get_drvdata(struct regulator_dev *rdev); 711 struct device *rdev_get_dev(struct regulator_dev *rdev); 712 struct regmap *rdev_get_regmap(struct regulator_dev *rdev); 713 int rdev_get_id(struct regulator_dev *rdev); 714 715 int regulator_mode_to_status(unsigned int); 716 717 int regulator_list_voltage_linear(struct regulator_dev *rdev, 718 unsigned int selector); 719 int regulator_list_voltage_pickable_linear_range(struct regulator_dev *rdev, 720 unsigned int selector); 721 int regulator_list_voltage_linear_range(struct regulator_dev *rdev, 722 unsigned int selector); 723 int regulator_list_voltage_table(struct regulator_dev *rdev, 724 unsigned int selector); 725 int regulator_map_voltage_linear(struct regulator_dev *rdev, 726 int min_uV, int max_uV); 727 int regulator_map_voltage_pickable_linear_range(struct regulator_dev *rdev, 728 int min_uV, int max_uV); 729 int regulator_map_voltage_linear_range(struct regulator_dev *rdev, 730 int min_uV, int max_uV); 731 int regulator_map_voltage_iterate(struct regulator_dev *rdev, 732 int min_uV, int max_uV); 733 int regulator_map_voltage_ascend(struct regulator_dev *rdev, 734 int min_uV, int max_uV); 735 int regulator_get_voltage_sel_pickable_regmap(struct regulator_dev *rdev); 736 int regulator_set_voltage_sel_pickable_regmap(struct regulator_dev *rdev, 737 unsigned int sel); 738 int regulator_get_voltage_sel_regmap(struct regulator_dev *rdev); 739 int regulator_set_voltage_sel_regmap(struct regulator_dev *rdev, unsigned sel); 740 int regulator_is_enabled_regmap(struct regulator_dev *rdev); 741 int regulator_enable_regmap(struct regulator_dev *rdev); 742 int regulator_disable_regmap(struct regulator_dev *rdev); 743 int regulator_set_voltage_time_sel(struct regulator_dev *rdev, 744 unsigned int old_selector, 745 unsigned int new_selector); 746 int regulator_set_bypass_regmap(struct regulator_dev *rdev, bool enable); 747 int regulator_get_bypass_regmap(struct regulator_dev *rdev, bool *enable); 748 int regulator_set_soft_start_regmap(struct regulator_dev *rdev); 749 int regulator_set_pull_down_regmap(struct regulator_dev *rdev); 750 751 int regulator_set_active_discharge_regmap(struct regulator_dev *rdev, 752 bool enable); 753 int regulator_set_current_limit_regmap(struct regulator_dev *rdev, 754 int min_uA, int max_uA); 755 int regulator_get_current_limit_regmap(struct regulator_dev *rdev); 756 void *regulator_get_init_drvdata(struct regulator_init_data *reg_init_data); 757 int regulator_find_closest_bigger(unsigned int target, const unsigned int *table, 758 unsigned int num_sel, unsigned int *sel); 759 int regulator_set_ramp_delay_regmap(struct regulator_dev *rdev, int ramp_delay); 760 int regulator_sync_voltage_rdev(struct regulator_dev *rdev); 761 762 /* 763 * Helper functions intended to be used by regulator drivers prior registering 764 * their regulators. 765 */ 766 int regulator_desc_list_voltage_linear_range(const struct regulator_desc *desc, 767 unsigned int selector); 768 769 int regulator_desc_list_voltage_linear(const struct regulator_desc *desc, 770 unsigned int selector); 771 772 #ifdef CONFIG_REGULATOR 773 const char *rdev_get_name(struct regulator_dev *rdev); 774 #else 775 static inline const char *rdev_get_name(struct regulator_dev *rdev) 776 { 777 return NULL; 778 } 779 #endif 780 781 #endif 782