1 /* SPDX-License-Identifier: GPL-2.0-only */ 2 /* 3 * driver.h -- SoC Regulator driver support. 4 * 5 * Copyright (C) 2007, 2008 Wolfson Microelectronics PLC. 6 * 7 * Author: Liam Girdwood <lrg@slimlogic.co.uk> 8 * 9 * Regulator Driver Interface. 10 */ 11 12 #ifndef __LINUX_REGULATOR_DRIVER_H_ 13 #define __LINUX_REGULATOR_DRIVER_H_ 14 15 #include <linux/device.h> 16 #include <linux/linear_range.h> 17 #include <linux/notifier.h> 18 #include <linux/regulator/consumer.h> 19 #include <linux/ww_mutex.h> 20 21 struct gpio_desc; 22 struct regmap; 23 struct regulator_dev; 24 struct regulator_config; 25 struct regulator_init_data; 26 struct regulator_enable_gpio; 27 28 enum regulator_status { 29 REGULATOR_STATUS_OFF, 30 REGULATOR_STATUS_ON, 31 REGULATOR_STATUS_ERROR, 32 /* fast/normal/idle/standby are flavors of "on" */ 33 REGULATOR_STATUS_FAST, 34 REGULATOR_STATUS_NORMAL, 35 REGULATOR_STATUS_IDLE, 36 REGULATOR_STATUS_STANDBY, 37 /* The regulator is enabled but not regulating */ 38 REGULATOR_STATUS_BYPASS, 39 /* in case that any other status doesn't apply */ 40 REGULATOR_STATUS_UNDEFINED, 41 }; 42 43 enum regulator_detection_severity { 44 /* Hardware shut down voltage outputs if condition is detected */ 45 REGULATOR_SEVERITY_PROT, 46 /* Hardware is probably damaged/inoperable */ 47 REGULATOR_SEVERITY_ERR, 48 /* Hardware is still recoverable but recovery action must be taken */ 49 REGULATOR_SEVERITY_WARN, 50 }; 51 52 /* Initialize struct linear_range for regulators */ 53 #define REGULATOR_LINEAR_RANGE(_min_uV, _min_sel, _max_sel, _step_uV) \ 54 { \ 55 .min = _min_uV, \ 56 .min_sel = _min_sel, \ 57 .max_sel = _max_sel, \ 58 .step = _step_uV, \ 59 } 60 61 /** 62 * struct regulator_ops - regulator operations. 63 * 64 * @enable: Configure the regulator as enabled. 65 * @disable: Configure the regulator as disabled. 66 * @is_enabled: Return 1 if the regulator is enabled, 0 if not. 67 * May also return negative errno. 68 * 69 * @set_voltage: Set the voltage for the regulator within the range specified. 70 * The driver should select the voltage closest to min_uV. 71 * @set_voltage_sel: Set the voltage for the regulator using the specified 72 * selector. 73 * @map_voltage: Convert a voltage into a selector 74 * @get_voltage: Return the currently configured voltage for the regulator; 75 * return -ENOTRECOVERABLE if regulator can't be read at 76 * bootup and hasn't been set yet. 77 * @get_voltage_sel: Return the currently configured voltage selector for the 78 * regulator; return -ENOTRECOVERABLE if regulator can't 79 * be read at bootup and hasn't been set yet. 80 * @list_voltage: Return one of the supported voltages, in microvolts; zero 81 * if the selector indicates a voltage that is unusable on this system; 82 * or negative errno. Selectors range from zero to one less than 83 * regulator_desc.n_voltages. Voltages may be reported in any order. 84 * 85 * @set_current_limit: Configure a limit for a current-limited regulator. 86 * The driver should select the current closest to max_uA. 87 * @get_current_limit: Get the configured limit for a current-limited regulator. 88 * @set_input_current_limit: Configure an input limit. 89 * 90 * @set_over_current_protection: Support enabling of and setting limits for over 91 * current situation detection. Detection can be configured for three 92 * levels of severity. 93 * REGULATOR_SEVERITY_PROT should automatically shut down the regulator(s). 94 * REGULATOR_SEVERITY_ERR should indicate that over-current situation is 95 * caused by an unrecoverable error but HW does not perform 96 * automatic shut down. 97 * REGULATOR_SEVERITY_WARN should indicate situation where hardware is 98 * still believed to not be damaged but that a board sepcific 99 * recovery action is needed. If lim_uA is 0 the limit should not 100 * be changed but the detection should just be enabled/disabled as 101 * is requested. 102 * @set_over_voltage_protection: Support enabling of and setting limits for over 103 * voltage situation detection. Detection can be configured for same 104 * severities as over current protection. 105 * @set_under_voltage_protection: Support enabling of and setting limits for 106 * under situation detection. 107 * @set_thermal_protection: Support enabling of and setting limits for over 108 * temperature situation detection. 109 * 110 * @set_active_discharge: Set active discharge enable/disable of regulators. 111 * 112 * @set_mode: Set the configured operating mode for the regulator. 113 * @get_mode: Get the configured operating mode for the regulator. 114 * @get_error_flags: Get the current error(s) for the regulator. 115 * @get_status: Return actual (not as-configured) status of regulator, as a 116 * REGULATOR_STATUS value (or negative errno) 117 * @get_optimum_mode: Get the most efficient operating mode for the regulator 118 * when running with the specified parameters. 119 * @set_load: Set the load for the regulator. 120 * 121 * @set_bypass: Set the regulator in bypass mode. 122 * @get_bypass: Get the regulator bypass mode state. 123 * 124 * @enable_time: Time taken for the regulator voltage output voltage to 125 * stabilise after being enabled, in microseconds. 126 * @set_ramp_delay: Set the ramp delay for the regulator. The driver should 127 * select ramp delay equal to or less than(closest) ramp_delay. 128 * @set_voltage_time: Time taken for the regulator voltage output voltage 129 * to stabilise after being set to a new value, in microseconds. 130 * The function receives the from and to voltage as input, it 131 * should return the worst case. 132 * @set_voltage_time_sel: Time taken for the regulator voltage output voltage 133 * to stabilise after being set to a new value, in microseconds. 134 * The function receives the from and to voltage selector as 135 * input, it should return the worst case. 136 * @set_soft_start: Enable soft start for the regulator. 137 * 138 * @set_suspend_voltage: Set the voltage for the regulator when the system 139 * is suspended. 140 * @set_suspend_enable: Mark the regulator as enabled when the system is 141 * suspended. 142 * @set_suspend_disable: Mark the regulator as disabled when the system is 143 * suspended. 144 * @set_suspend_mode: Set the operating mode for the regulator when the 145 * system is suspended. 146 * @resume: Resume operation of suspended regulator. 147 * @set_pull_down: Configure the regulator to pull down when the regulator 148 * is disabled. 149 * 150 * This struct describes regulator operations which can be implemented by 151 * regulator chip drivers. 152 */ 153 struct regulator_ops { 154 155 /* enumerate supported voltages */ 156 int (*list_voltage) (struct regulator_dev *, unsigned selector); 157 158 /* get/set regulator voltage */ 159 int (*set_voltage) (struct regulator_dev *, int min_uV, int max_uV, 160 unsigned *selector); 161 int (*map_voltage)(struct regulator_dev *, int min_uV, int max_uV); 162 int (*set_voltage_sel) (struct regulator_dev *, unsigned selector); 163 int (*get_voltage) (struct regulator_dev *); 164 int (*get_voltage_sel) (struct regulator_dev *); 165 166 /* get/set regulator current */ 167 int (*set_current_limit) (struct regulator_dev *, 168 int min_uA, int max_uA); 169 int (*get_current_limit) (struct regulator_dev *); 170 171 int (*set_input_current_limit) (struct regulator_dev *, int lim_uA); 172 int (*set_over_current_protection)(struct regulator_dev *, int lim_uA, 173 int severity, bool enable); 174 int (*set_over_voltage_protection)(struct regulator_dev *, int lim_uV, 175 int severity, bool enable); 176 int (*set_under_voltage_protection)(struct regulator_dev *, int lim_uV, 177 int severity, bool enable); 178 int (*set_thermal_protection)(struct regulator_dev *, int lim, 179 int severity, bool enable); 180 int (*set_active_discharge)(struct regulator_dev *, bool enable); 181 182 /* enable/disable regulator */ 183 int (*enable) (struct regulator_dev *); 184 int (*disable) (struct regulator_dev *); 185 int (*is_enabled) (struct regulator_dev *); 186 187 /* get/set regulator operating mode (defined in consumer.h) */ 188 int (*set_mode) (struct regulator_dev *, unsigned int mode); 189 unsigned int (*get_mode) (struct regulator_dev *); 190 191 /* retrieve current error flags on the regulator */ 192 int (*get_error_flags)(struct regulator_dev *, unsigned int *flags); 193 194 /* Time taken to enable or set voltage on the regulator */ 195 int (*enable_time) (struct regulator_dev *); 196 int (*set_ramp_delay) (struct regulator_dev *, int ramp_delay); 197 int (*set_voltage_time) (struct regulator_dev *, int old_uV, 198 int new_uV); 199 int (*set_voltage_time_sel) (struct regulator_dev *, 200 unsigned int old_selector, 201 unsigned int new_selector); 202 203 int (*set_soft_start) (struct regulator_dev *); 204 205 /* report regulator status ... most other accessors report 206 * control inputs, this reports results of combining inputs 207 * from Linux (and other sources) with the actual load. 208 * returns REGULATOR_STATUS_* or negative errno. 209 */ 210 int (*get_status)(struct regulator_dev *); 211 212 /* get most efficient regulator operating mode for load */ 213 unsigned int (*get_optimum_mode) (struct regulator_dev *, int input_uV, 214 int output_uV, int load_uA); 215 /* set the load on the regulator */ 216 int (*set_load)(struct regulator_dev *, int load_uA); 217 218 /* control and report on bypass mode */ 219 int (*set_bypass)(struct regulator_dev *dev, bool enable); 220 int (*get_bypass)(struct regulator_dev *dev, bool *enable); 221 222 /* the operations below are for configuration of regulator state when 223 * its parent PMIC enters a global STANDBY/HIBERNATE state */ 224 225 /* set regulator suspend voltage */ 226 int (*set_suspend_voltage) (struct regulator_dev *, int uV); 227 228 /* enable/disable regulator in suspend state */ 229 int (*set_suspend_enable) (struct regulator_dev *); 230 int (*set_suspend_disable) (struct regulator_dev *); 231 232 /* set regulator suspend operating mode (defined in consumer.h) */ 233 int (*set_suspend_mode) (struct regulator_dev *, unsigned int mode); 234 235 int (*resume)(struct regulator_dev *rdev); 236 237 int (*set_pull_down) (struct regulator_dev *); 238 }; 239 240 /* 241 * Regulators can either control voltage or current. 242 */ 243 enum regulator_type { 244 REGULATOR_VOLTAGE, 245 REGULATOR_CURRENT, 246 }; 247 248 /** 249 * struct regulator_desc - Static regulator descriptor 250 * 251 * Each regulator registered with the core is described with a 252 * structure of this type and a struct regulator_config. This 253 * structure contains the non-varying parts of the regulator 254 * description. 255 * 256 * @name: Identifying name for the regulator. 257 * @supply_name: Identifying the regulator supply 258 * @of_match: Name used to identify regulator in DT. 259 * @of_match_full_name: A flag to indicate that the of_match string, if 260 * present, should be matched against the node full_name. 261 * @regulators_node: Name of node containing regulator definitions in DT. 262 * @of_parse_cb: Optional callback called only if of_match is present. 263 * Will be called for each regulator parsed from DT, during 264 * init_data parsing. 265 * The regulator_config passed as argument to the callback will 266 * be a copy of config passed to regulator_register, valid only 267 * for this particular call. Callback may freely change the 268 * config but it cannot store it for later usage. 269 * Callback should return 0 on success or negative ERRNO 270 * indicating failure. 271 * @id: Numerical identifier for the regulator. 272 * @ops: Regulator operations table. 273 * @irq: Interrupt number for the regulator. 274 * @type: Indicates if the regulator is a voltage or current regulator. 275 * @owner: Module providing the regulator, used for refcounting. 276 * 277 * @continuous_voltage_range: Indicates if the regulator can set any 278 * voltage within constrains range. 279 * @n_voltages: Number of selectors available for ops.list_voltage(). 280 * @n_current_limits: Number of selectors available for current limits 281 * 282 * @min_uV: Voltage given by the lowest selector (if linear mapping) 283 * @uV_step: Voltage increase with each selector (if linear mapping) 284 * @linear_min_sel: Minimal selector for starting linear mapping 285 * @fixed_uV: Fixed voltage of rails. 286 * @ramp_delay: Time to settle down after voltage change (unit: uV/us) 287 * @min_dropout_uV: The minimum dropout voltage this regulator can handle 288 * @linear_ranges: A constant table of possible voltage ranges. 289 * @linear_range_selectors: A constant table of voltage range selectors. 290 * If pickable ranges are used each range must 291 * have corresponding selector here. 292 * @n_linear_ranges: Number of entries in the @linear_ranges (and in 293 * linear_range_selectors if used) table(s). 294 * @volt_table: Voltage mapping table (if table based mapping) 295 * @curr_table: Current limit mapping table (if table based mapping) 296 * 297 * @vsel_range_reg: Register for range selector when using pickable ranges 298 * and ``regulator_map_*_voltage_*_pickable`` functions. 299 * @vsel_range_mask: Mask for register bitfield used for range selector 300 * @vsel_reg: Register for selector when using ``regulator_map_*_voltage_*`` 301 * @vsel_mask: Mask for register bitfield used for selector 302 * @vsel_step: Specify the resolution of selector stepping when setting 303 * voltage. If 0, then no stepping is done (requested selector is 304 * set directly), if >0 then the regulator API will ramp the 305 * voltage up/down gradually each time increasing/decreasing the 306 * selector by the specified step value. 307 * @csel_reg: Register for current limit selector using regmap set_current_limit 308 * @csel_mask: Mask for register bitfield used for current limit selector 309 * @apply_reg: Register for initiate voltage change on the output when 310 * using regulator_set_voltage_sel_regmap 311 * @apply_bit: Register bitfield used for initiate voltage change on the 312 * output when using regulator_set_voltage_sel_regmap 313 * @enable_reg: Register for control when using regmap enable/disable ops 314 * @enable_mask: Mask for control when using regmap enable/disable ops 315 * @enable_val: Enabling value for control when using regmap enable/disable ops 316 * @disable_val: Disabling value for control when using regmap enable/disable ops 317 * @enable_is_inverted: A flag to indicate set enable_mask bits to disable 318 * when using regulator_enable_regmap and friends APIs. 319 * @bypass_reg: Register for control when using regmap set_bypass 320 * @bypass_mask: Mask for control when using regmap set_bypass 321 * @bypass_val_on: Enabling value for control when using regmap set_bypass 322 * @bypass_val_off: Disabling value for control when using regmap set_bypass 323 * @active_discharge_off: Enabling value for control when using regmap 324 * set_active_discharge 325 * @active_discharge_on: Disabling value for control when using regmap 326 * set_active_discharge 327 * @active_discharge_mask: Mask for control when using regmap 328 * set_active_discharge 329 * @active_discharge_reg: Register for control when using regmap 330 * set_active_discharge 331 * @soft_start_reg: Register for control when using regmap set_soft_start 332 * @soft_start_mask: Mask for control when using regmap set_soft_start 333 * @soft_start_val_on: Enabling value for control when using regmap 334 * set_soft_start 335 * @pull_down_reg: Register for control when using regmap set_pull_down 336 * @pull_down_mask: Mask for control when using regmap set_pull_down 337 * @pull_down_val_on: Enabling value for control when using regmap 338 * set_pull_down 339 * 340 * @ramp_reg: Register for controlling the regulator ramp-rate. 341 * @ramp_mask: Bitmask for the ramp-rate control register. 342 * @ramp_delay_table: Table for mapping the regulator ramp-rate values. Values 343 * should be given in units of V/S (uV/uS). See the 344 * regulator_set_ramp_delay_regmap(). 345 * 346 * @enable_time: Time taken for initial enable of regulator (in uS). 347 * @off_on_delay: guard time (in uS), before re-enabling a regulator 348 * 349 * @poll_enabled_time: The polling interval (in uS) to use while checking that 350 * the regulator was actually enabled. Max upto enable_time. 351 * 352 * @of_map_mode: Maps a hardware mode defined in a DeviceTree to a standard mode 353 */ 354 struct regulator_desc { 355 const char *name; 356 const char *supply_name; 357 const char *of_match; 358 bool of_match_full_name; 359 const char *regulators_node; 360 int (*of_parse_cb)(struct device_node *, 361 const struct regulator_desc *, 362 struct regulator_config *); 363 int id; 364 unsigned int continuous_voltage_range:1; 365 unsigned n_voltages; 366 unsigned int n_current_limits; 367 const struct regulator_ops *ops; 368 int irq; 369 enum regulator_type type; 370 struct module *owner; 371 372 unsigned int min_uV; 373 unsigned int uV_step; 374 unsigned int linear_min_sel; 375 int fixed_uV; 376 unsigned int ramp_delay; 377 int min_dropout_uV; 378 379 const struct linear_range *linear_ranges; 380 const unsigned int *linear_range_selectors; 381 382 int n_linear_ranges; 383 384 const unsigned int *volt_table; 385 const unsigned int *curr_table; 386 387 unsigned int vsel_range_reg; 388 unsigned int vsel_range_mask; 389 unsigned int vsel_reg; 390 unsigned int vsel_mask; 391 unsigned int vsel_step; 392 unsigned int csel_reg; 393 unsigned int csel_mask; 394 unsigned int apply_reg; 395 unsigned int apply_bit; 396 unsigned int enable_reg; 397 unsigned int enable_mask; 398 unsigned int enable_val; 399 unsigned int disable_val; 400 bool enable_is_inverted; 401 unsigned int bypass_reg; 402 unsigned int bypass_mask; 403 unsigned int bypass_val_on; 404 unsigned int bypass_val_off; 405 unsigned int active_discharge_on; 406 unsigned int active_discharge_off; 407 unsigned int active_discharge_mask; 408 unsigned int active_discharge_reg; 409 unsigned int soft_start_reg; 410 unsigned int soft_start_mask; 411 unsigned int soft_start_val_on; 412 unsigned int pull_down_reg; 413 unsigned int pull_down_mask; 414 unsigned int pull_down_val_on; 415 unsigned int ramp_reg; 416 unsigned int ramp_mask; 417 const unsigned int *ramp_delay_table; 418 unsigned int n_ramp_values; 419 420 unsigned int enable_time; 421 422 unsigned int off_on_delay; 423 424 unsigned int poll_enabled_time; 425 426 unsigned int (*of_map_mode)(unsigned int mode); 427 }; 428 429 /** 430 * struct regulator_config - Dynamic regulator descriptor 431 * 432 * Each regulator registered with the core is described with a 433 * structure of this type and a struct regulator_desc. This structure 434 * contains the runtime variable parts of the regulator description. 435 * 436 * @dev: struct device for the regulator 437 * @init_data: platform provided init data, passed through by driver 438 * @driver_data: private regulator data 439 * @of_node: OpenFirmware node to parse for device tree bindings (may be 440 * NULL). 441 * @regmap: regmap to use for core regmap helpers if dev_get_regmap() is 442 * insufficient. 443 * @ena_gpiod: GPIO controlling regulator enable. 444 */ 445 struct regulator_config { 446 struct device *dev; 447 const struct regulator_init_data *init_data; 448 void *driver_data; 449 struct device_node *of_node; 450 struct regmap *regmap; 451 452 struct gpio_desc *ena_gpiod; 453 }; 454 455 /** 456 * struct regulator_err_state - regulator error/notification status 457 * 458 * @rdev: Regulator which status the struct indicates. 459 * @notifs: Events which have occurred on the regulator. 460 * @errors: Errors which are active on the regulator. 461 * @possible_errs: Errors which can be signaled (by given IRQ). 462 */ 463 struct regulator_err_state { 464 struct regulator_dev *rdev; 465 unsigned long notifs; 466 unsigned long errors; 467 int possible_errs; 468 }; 469 470 /** 471 * struct regulator_irq_data - regulator error/notification status data 472 * 473 * @states: Status structs for each of the associated regulators. 474 * @num_states: Amount of associated regulators. 475 * @data: Driver data pointer given at regulator_irq_desc. 476 * @opaque: Value storage for IC driver. Core does not update this. ICs 477 * may want to store status register value here at map_event and 478 * compare contents at 'renable' callback to see if new problems 479 * have been added to status. If that is the case it may be 480 * desirable to return REGULATOR_ERROR_CLEARED and not 481 * REGULATOR_ERROR_ON to allow IRQ fire again and to generate 482 * notifications also for the new issues. 483 * 484 * This structure is passed to 'map_event' and 'renable' callbacks for 485 * reporting regulator status to core. 486 */ 487 struct regulator_irq_data { 488 struct regulator_err_state *states; 489 int num_states; 490 void *data; 491 long opaque; 492 }; 493 494 /** 495 * struct regulator_irq_desc - notification sender for IRQ based events. 496 * 497 * @name: The visible name for the IRQ 498 * @fatal_cnt: If this IRQ is used to signal HW damaging condition it may be 499 * best to shut-down regulator(s) or reboot the SOC if error 500 * handling is repeatedly failing. If fatal_cnt is given the IRQ 501 * handling is aborted if it fails for fatal_cnt times and die() 502 * callback (if populated) or BUG() is called to try to prevent 503 * further damage. 504 * @reread_ms: The time which is waited before attempting to re-read status 505 * at the worker if IC reading fails. Immediate re-read is done 506 * if time is not specified. 507 * @irq_off_ms: The time which IRQ is kept disabled before re-evaluating the 508 * status for devices which keep IRQ disabled for duration of the 509 * error. If this is not given the IRQ is left enabled and renable 510 * is not called. 511 * @skip_off: If set to true the IRQ handler will attempt to check if any of 512 * the associated regulators are enabled prior to taking other 513 * actions. If no regulators are enabled and this is set to true 514 * a spurious IRQ is assumed and IRQ_NONE is returned. 515 * @high_prio: Boolean to indicate that high priority WQ should be used. 516 * @data: Driver private data pointer which will be passed as such to 517 * the renable, map_event and die callbacks in regulator_irq_data. 518 * @die: Protection callback. If IC status reading or recovery actions 519 * fail fatal_cnt times this callback or BUG() is called. This 520 * callback should implement a final protection attempt like 521 * disabling the regulator. If protection succeeded this may 522 * return 0. If anything else is returned the core assumes final 523 * protection failed and calls BUG() as a last resort. 524 * @map_event: Driver callback to map IRQ status into regulator devices with 525 * events / errors. NOTE: callback MUST initialize both the 526 * errors and notifs for all rdevs which it signals having 527 * active events as core does not clean the map data. 528 * REGULATOR_FAILED_RETRY can be returned to indicate that the 529 * status reading from IC failed. If this is repeated for 530 * fatal_cnt times the core will call die() callback or power-off 531 * the system as a last resort to protect the HW. 532 * @renable: Optional callback to check status (if HW supports that) before 533 * re-enabling IRQ. If implemented this should clear the error 534 * flags so that errors fetched by regulator_get_error_flags() 535 * are updated. If callback is not implemented then errors are 536 * assumed to be cleared and IRQ is re-enabled. 537 * REGULATOR_FAILED_RETRY can be returned to 538 * indicate that the status reading from IC failed. If this is 539 * repeated for 'fatal_cnt' times the core will call die() 540 * callback or if die() is not populated then attempt to power-off 541 * the system as a last resort to protect the HW. 542 * Returning zero indicates that the problem in HW has been solved 543 * and IRQ will be re-enabled. Returning REGULATOR_ERROR_ON 544 * indicates the error condition is still active and keeps IRQ 545 * disabled. Please note that returning REGULATOR_ERROR_ON does 546 * not retrigger evaluating what events are active or resending 547 * notifications. If this is needed you probably want to return 548 * zero and allow IRQ to retrigger causing events to be 549 * re-evaluated and re-sent. 550 * 551 * This structure is used for registering regulator IRQ notification helper. 552 */ 553 struct regulator_irq_desc { 554 const char *name; 555 int irq_flags; 556 int fatal_cnt; 557 int reread_ms; 558 int irq_off_ms; 559 bool skip_off; 560 bool high_prio; 561 void *data; 562 563 int (*die)(struct regulator_irq_data *rid); 564 int (*map_event)(int irq, struct regulator_irq_data *rid, 565 unsigned long *dev_mask); 566 int (*renable)(struct regulator_irq_data *rid); 567 }; 568 569 /* 570 * Return values for regulator IRQ helpers. 571 */ 572 enum { 573 REGULATOR_ERROR_CLEARED, 574 REGULATOR_FAILED_RETRY, 575 REGULATOR_ERROR_ON, 576 }; 577 578 /* 579 * struct coupling_desc 580 * 581 * Describes coupling of regulators. Each regulator should have 582 * at least a pointer to itself in coupled_rdevs array. 583 * When a new coupled regulator is resolved, n_resolved is 584 * incremented. 585 */ 586 struct coupling_desc { 587 struct regulator_dev **coupled_rdevs; 588 struct regulator_coupler *coupler; 589 int n_resolved; 590 int n_coupled; 591 }; 592 593 /* 594 * struct regulator_dev 595 * 596 * Voltage / Current regulator class device. One for each 597 * regulator. 598 * 599 * This should *not* be used directly by anything except the regulator 600 * core and notification injection (which should take the mutex and do 601 * no other direct access). 602 */ 603 struct regulator_dev { 604 const struct regulator_desc *desc; 605 int exclusive; 606 u32 use_count; 607 u32 open_count; 608 u32 bypass_count; 609 610 /* lists we belong to */ 611 struct list_head list; /* list of all regulators */ 612 613 /* lists we own */ 614 struct list_head consumer_list; /* consumers we supply */ 615 616 struct coupling_desc coupling_desc; 617 618 struct blocking_notifier_head notifier; 619 struct ww_mutex mutex; /* consumer lock */ 620 struct task_struct *mutex_owner; 621 int ref_cnt; 622 struct module *owner; 623 struct device dev; 624 struct regulation_constraints *constraints; 625 struct regulator *supply; /* for tree */ 626 const char *supply_name; 627 struct regmap *regmap; 628 629 struct delayed_work disable_work; 630 631 void *reg_data; /* regulator_dev data */ 632 633 struct dentry *debugfs; 634 635 struct regulator_enable_gpio *ena_pin; 636 unsigned int ena_gpio_state:1; 637 638 unsigned int is_switch:1; 639 640 /* time when this regulator was disabled last time */ 641 ktime_t last_off; 642 int cached_err; 643 bool use_cached_err; 644 spinlock_t err_lock; 645 }; 646 647 struct regulator_dev * 648 regulator_register(const struct regulator_desc *regulator_desc, 649 const struct regulator_config *config); 650 struct regulator_dev * 651 devm_regulator_register(struct device *dev, 652 const struct regulator_desc *regulator_desc, 653 const struct regulator_config *config); 654 void regulator_unregister(struct regulator_dev *rdev); 655 656 int regulator_notifier_call_chain(struct regulator_dev *rdev, 657 unsigned long event, void *data); 658 void *devm_regulator_irq_helper(struct device *dev, 659 const struct regulator_irq_desc *d, int irq, 660 int irq_flags, int common_errs, 661 int *per_rdev_errs, struct regulator_dev **rdev, 662 int rdev_amount); 663 void *regulator_irq_helper(struct device *dev, 664 const struct regulator_irq_desc *d, int irq, 665 int irq_flags, int common_errs, int *per_rdev_errs, 666 struct regulator_dev **rdev, int rdev_amount); 667 void regulator_irq_helper_cancel(void **handle); 668 669 void *rdev_get_drvdata(struct regulator_dev *rdev); 670 struct device *rdev_get_dev(struct regulator_dev *rdev); 671 struct regmap *rdev_get_regmap(struct regulator_dev *rdev); 672 int rdev_get_id(struct regulator_dev *rdev); 673 674 int regulator_mode_to_status(unsigned int); 675 676 int regulator_list_voltage_linear(struct regulator_dev *rdev, 677 unsigned int selector); 678 int regulator_list_voltage_pickable_linear_range(struct regulator_dev *rdev, 679 unsigned int selector); 680 int regulator_list_voltage_linear_range(struct regulator_dev *rdev, 681 unsigned int selector); 682 int regulator_list_voltage_table(struct regulator_dev *rdev, 683 unsigned int selector); 684 int regulator_map_voltage_linear(struct regulator_dev *rdev, 685 int min_uV, int max_uV); 686 int regulator_map_voltage_pickable_linear_range(struct regulator_dev *rdev, 687 int min_uV, int max_uV); 688 int regulator_map_voltage_linear_range(struct regulator_dev *rdev, 689 int min_uV, int max_uV); 690 int regulator_map_voltage_iterate(struct regulator_dev *rdev, 691 int min_uV, int max_uV); 692 int regulator_map_voltage_ascend(struct regulator_dev *rdev, 693 int min_uV, int max_uV); 694 int regulator_get_voltage_sel_pickable_regmap(struct regulator_dev *rdev); 695 int regulator_set_voltage_sel_pickable_regmap(struct regulator_dev *rdev, 696 unsigned int sel); 697 int regulator_get_voltage_sel_regmap(struct regulator_dev *rdev); 698 int regulator_set_voltage_sel_regmap(struct regulator_dev *rdev, unsigned sel); 699 int regulator_is_enabled_regmap(struct regulator_dev *rdev); 700 int regulator_enable_regmap(struct regulator_dev *rdev); 701 int regulator_disable_regmap(struct regulator_dev *rdev); 702 int regulator_set_voltage_time_sel(struct regulator_dev *rdev, 703 unsigned int old_selector, 704 unsigned int new_selector); 705 int regulator_set_bypass_regmap(struct regulator_dev *rdev, bool enable); 706 int regulator_get_bypass_regmap(struct regulator_dev *rdev, bool *enable); 707 int regulator_set_soft_start_regmap(struct regulator_dev *rdev); 708 int regulator_set_pull_down_regmap(struct regulator_dev *rdev); 709 710 int regulator_set_active_discharge_regmap(struct regulator_dev *rdev, 711 bool enable); 712 int regulator_set_current_limit_regmap(struct regulator_dev *rdev, 713 int min_uA, int max_uA); 714 int regulator_get_current_limit_regmap(struct regulator_dev *rdev); 715 void *regulator_get_init_drvdata(struct regulator_init_data *reg_init_data); 716 int regulator_set_ramp_delay_regmap(struct regulator_dev *rdev, int ramp_delay); 717 int regulator_sync_voltage_rdev(struct regulator_dev *rdev); 718 719 /* 720 * Helper functions intended to be used by regulator drivers prior registering 721 * their regulators. 722 */ 723 int regulator_desc_list_voltage_linear_range(const struct regulator_desc *desc, 724 unsigned int selector); 725 726 int regulator_desc_list_voltage_linear(const struct regulator_desc *desc, 727 unsigned int selector); 728 729 #ifdef CONFIG_REGULATOR 730 const char *rdev_get_name(struct regulator_dev *rdev); 731 #else 732 static inline const char *rdev_get_name(struct regulator_dev *rdev) 733 { 734 return NULL; 735 } 736 #endif 737 738 #endif 739