1 /* SPDX-License-Identifier: GPL-2.0-only */ 2 /* 3 * driver.h -- SoC Regulator driver support. 4 * 5 * Copyright (C) 2007, 2008 Wolfson Microelectronics PLC. 6 * 7 * Author: Liam Girdwood <lrg@slimlogic.co.uk> 8 * 9 * Regulator Driver Interface. 10 */ 11 12 #ifndef __LINUX_REGULATOR_DRIVER_H_ 13 #define __LINUX_REGULATOR_DRIVER_H_ 14 15 #include <linux/device.h> 16 #include <linux/linear_range.h> 17 #include <linux/notifier.h> 18 #include <linux/regulator/consumer.h> 19 #include <linux/ww_mutex.h> 20 21 struct gpio_desc; 22 struct regmap; 23 struct regulator_dev; 24 struct regulator_config; 25 struct regulator_init_data; 26 struct regulator_enable_gpio; 27 28 enum regulator_status { 29 REGULATOR_STATUS_OFF, 30 REGULATOR_STATUS_ON, 31 REGULATOR_STATUS_ERROR, 32 /* fast/normal/idle/standby are flavors of "on" */ 33 REGULATOR_STATUS_FAST, 34 REGULATOR_STATUS_NORMAL, 35 REGULATOR_STATUS_IDLE, 36 REGULATOR_STATUS_STANDBY, 37 /* The regulator is enabled but not regulating */ 38 REGULATOR_STATUS_BYPASS, 39 /* in case that any other status doesn't apply */ 40 REGULATOR_STATUS_UNDEFINED, 41 }; 42 43 enum regulator_detection_severity { 44 /* Hardware shut down voltage outputs if condition is detected */ 45 REGULATOR_SEVERITY_PROT, 46 /* Hardware is probably damaged/inoperable */ 47 REGULATOR_SEVERITY_ERR, 48 /* Hardware is still recoverable but recovery action must be taken */ 49 REGULATOR_SEVERITY_WARN, 50 }; 51 52 /* Initialize struct linear_range for regulators */ 53 #define REGULATOR_LINEAR_RANGE(_min_uV, _min_sel, _max_sel, _step_uV) \ 54 { \ 55 .min = _min_uV, \ 56 .min_sel = _min_sel, \ 57 .max_sel = _max_sel, \ 58 .step = _step_uV, \ 59 } 60 61 /** 62 * struct regulator_ops - regulator operations. 63 * 64 * @enable: Configure the regulator as enabled. 65 * @disable: Configure the regulator as disabled. 66 * @is_enabled: Return 1 if the regulator is enabled, 0 if not. 67 * May also return negative errno. 68 * 69 * @set_voltage: Set the voltage for the regulator within the range specified. 70 * The driver should select the voltage closest to min_uV. 71 * @set_voltage_sel: Set the voltage for the regulator using the specified 72 * selector. 73 * @map_voltage: Convert a voltage into a selector 74 * @get_voltage: Return the currently configured voltage for the regulator; 75 * return -ENOTRECOVERABLE if regulator can't be read at 76 * bootup and hasn't been set yet. 77 * @get_voltage_sel: Return the currently configured voltage selector for the 78 * regulator; return -ENOTRECOVERABLE if regulator can't 79 * be read at bootup and hasn't been set yet. 80 * @list_voltage: Return one of the supported voltages, in microvolts; zero 81 * if the selector indicates a voltage that is unusable on this system; 82 * or negative errno. Selectors range from zero to one less than 83 * regulator_desc.n_voltages. Voltages may be reported in any order. 84 * 85 * @set_current_limit: Configure a limit for a current-limited regulator. 86 * The driver should select the current closest to max_uA. 87 * @get_current_limit: Get the configured limit for a current-limited regulator. 88 * @set_input_current_limit: Configure an input limit. 89 * 90 * @set_over_current_protection: Support enabling of and setting limits for over 91 * current situation detection. Detection can be configured for three 92 * levels of severity. 93 * 94 * - REGULATOR_SEVERITY_PROT should automatically shut down the regulator(s). 95 * 96 * - REGULATOR_SEVERITY_ERR should indicate that over-current situation is 97 * caused by an unrecoverable error but HW does not perform 98 * automatic shut down. 99 * 100 * - REGULATOR_SEVERITY_WARN should indicate situation where hardware is 101 * still believed to not be damaged but that a board sepcific 102 * recovery action is needed. If lim_uA is 0 the limit should not 103 * be changed but the detection should just be enabled/disabled as 104 * is requested. 105 * 106 * @set_over_voltage_protection: Support enabling of and setting limits for over 107 * voltage situation detection. Detection can be configured for same 108 * severities as over current protection. Units of uV. 109 * @set_under_voltage_protection: Support enabling of and setting limits for 110 * under voltage situation detection. Detection can be configured for same 111 * severities as over current protection. Units of uV. 112 * @set_thermal_protection: Support enabling of and setting limits for over 113 * temperature situation detection.Detection can be configured for same 114 * severities as over current protection. Units of degree Kelvin. 115 * 116 * @set_active_discharge: Set active discharge enable/disable of regulators. 117 * 118 * @set_mode: Set the configured operating mode for the regulator. 119 * @get_mode: Get the configured operating mode for the regulator. 120 * @get_error_flags: Get the current error(s) for the regulator. 121 * @get_status: Return actual (not as-configured) status of regulator, as a 122 * REGULATOR_STATUS value (or negative errno) 123 * @get_optimum_mode: Get the most efficient operating mode for the regulator 124 * when running with the specified parameters. 125 * @set_load: Set the load for the regulator. 126 * 127 * @set_bypass: Set the regulator in bypass mode. 128 * @get_bypass: Get the regulator bypass mode state. 129 * 130 * @enable_time: Time taken for the regulator voltage output voltage to 131 * stabilise after being enabled, in microseconds. 132 * @set_ramp_delay: Set the ramp delay for the regulator. The driver should 133 * select ramp delay equal to or less than(closest) ramp_delay. 134 * @set_voltage_time: Time taken for the regulator voltage output voltage 135 * to stabilise after being set to a new value, in microseconds. 136 * The function receives the from and to voltage as input, it 137 * should return the worst case. 138 * @set_voltage_time_sel: Time taken for the regulator voltage output voltage 139 * to stabilise after being set to a new value, in microseconds. 140 * The function receives the from and to voltage selector as 141 * input, it should return the worst case. 142 * @set_soft_start: Enable soft start for the regulator. 143 * 144 * @set_suspend_voltage: Set the voltage for the regulator when the system 145 * is suspended. 146 * @set_suspend_enable: Mark the regulator as enabled when the system is 147 * suspended. 148 * @set_suspend_disable: Mark the regulator as disabled when the system is 149 * suspended. 150 * @set_suspend_mode: Set the operating mode for the regulator when the 151 * system is suspended. 152 * @resume: Resume operation of suspended regulator. 153 * @set_pull_down: Configure the regulator to pull down when the regulator 154 * is disabled. 155 * 156 * This struct describes regulator operations which can be implemented by 157 * regulator chip drivers. 158 */ 159 struct regulator_ops { 160 161 /* enumerate supported voltages */ 162 int (*list_voltage) (struct regulator_dev *, unsigned selector); 163 164 /* get/set regulator voltage */ 165 int (*set_voltage) (struct regulator_dev *, int min_uV, int max_uV, 166 unsigned *selector); 167 int (*map_voltage)(struct regulator_dev *, int min_uV, int max_uV); 168 int (*set_voltage_sel) (struct regulator_dev *, unsigned selector); 169 int (*get_voltage) (struct regulator_dev *); 170 int (*get_voltage_sel) (struct regulator_dev *); 171 172 /* get/set regulator current */ 173 int (*set_current_limit) (struct regulator_dev *, 174 int min_uA, int max_uA); 175 int (*get_current_limit) (struct regulator_dev *); 176 177 int (*set_input_current_limit) (struct regulator_dev *, int lim_uA); 178 int (*set_over_current_protection)(struct regulator_dev *, int lim_uA, 179 int severity, bool enable); 180 int (*set_over_voltage_protection)(struct regulator_dev *, int lim_uV, 181 int severity, bool enable); 182 int (*set_under_voltage_protection)(struct regulator_dev *, int lim_uV, 183 int severity, bool enable); 184 int (*set_thermal_protection)(struct regulator_dev *, int lim, 185 int severity, bool enable); 186 int (*set_active_discharge)(struct regulator_dev *, bool enable); 187 188 /* enable/disable regulator */ 189 int (*enable) (struct regulator_dev *); 190 int (*disable) (struct regulator_dev *); 191 int (*is_enabled) (struct regulator_dev *); 192 193 /* get/set regulator operating mode (defined in consumer.h) */ 194 int (*set_mode) (struct regulator_dev *, unsigned int mode); 195 unsigned int (*get_mode) (struct regulator_dev *); 196 197 /* retrieve current error flags on the regulator */ 198 int (*get_error_flags)(struct regulator_dev *, unsigned int *flags); 199 200 /* Time taken to enable or set voltage on the regulator */ 201 int (*enable_time) (struct regulator_dev *); 202 int (*set_ramp_delay) (struct regulator_dev *, int ramp_delay); 203 int (*set_voltage_time) (struct regulator_dev *, int old_uV, 204 int new_uV); 205 int (*set_voltage_time_sel) (struct regulator_dev *, 206 unsigned int old_selector, 207 unsigned int new_selector); 208 209 int (*set_soft_start) (struct regulator_dev *); 210 211 /* report regulator status ... most other accessors report 212 * control inputs, this reports results of combining inputs 213 * from Linux (and other sources) with the actual load. 214 * returns REGULATOR_STATUS_* or negative errno. 215 */ 216 int (*get_status)(struct regulator_dev *); 217 218 /* get most efficient regulator operating mode for load */ 219 unsigned int (*get_optimum_mode) (struct regulator_dev *, int input_uV, 220 int output_uV, int load_uA); 221 /* set the load on the regulator */ 222 int (*set_load)(struct regulator_dev *, int load_uA); 223 224 /* control and report on bypass mode */ 225 int (*set_bypass)(struct regulator_dev *dev, bool enable); 226 int (*get_bypass)(struct regulator_dev *dev, bool *enable); 227 228 /* the operations below are for configuration of regulator state when 229 * its parent PMIC enters a global STANDBY/HIBERNATE state */ 230 231 /* set regulator suspend voltage */ 232 int (*set_suspend_voltage) (struct regulator_dev *, int uV); 233 234 /* enable/disable regulator in suspend state */ 235 int (*set_suspend_enable) (struct regulator_dev *); 236 int (*set_suspend_disable) (struct regulator_dev *); 237 238 /* set regulator suspend operating mode (defined in consumer.h) */ 239 int (*set_suspend_mode) (struct regulator_dev *, unsigned int mode); 240 241 int (*resume)(struct regulator_dev *rdev); 242 243 int (*set_pull_down) (struct regulator_dev *); 244 }; 245 246 /* 247 * Regulators can either control voltage or current. 248 */ 249 enum regulator_type { 250 REGULATOR_VOLTAGE, 251 REGULATOR_CURRENT, 252 }; 253 254 /** 255 * struct regulator_desc - Static regulator descriptor 256 * 257 * Each regulator registered with the core is described with a 258 * structure of this type and a struct regulator_config. This 259 * structure contains the non-varying parts of the regulator 260 * description. 261 * 262 * @name: Identifying name for the regulator. 263 * @supply_name: Identifying the regulator supply 264 * @of_match: Name used to identify regulator in DT. 265 * @of_match_full_name: A flag to indicate that the of_match string, if 266 * present, should be matched against the node full_name. 267 * @regulators_node: Name of node containing regulator definitions in DT. 268 * @of_parse_cb: Optional callback called only if of_match is present. 269 * Will be called for each regulator parsed from DT, during 270 * init_data parsing. 271 * The regulator_config passed as argument to the callback will 272 * be a copy of config passed to regulator_register, valid only 273 * for this particular call. Callback may freely change the 274 * config but it cannot store it for later usage. 275 * Callback should return 0 on success or negative ERRNO 276 * indicating failure. 277 * @id: Numerical identifier for the regulator. 278 * @ops: Regulator operations table. 279 * @irq: Interrupt number for the regulator. 280 * @type: Indicates if the regulator is a voltage or current regulator. 281 * @owner: Module providing the regulator, used for refcounting. 282 * 283 * @continuous_voltage_range: Indicates if the regulator can set any 284 * voltage within constrains range. 285 * @n_voltages: Number of selectors available for ops.list_voltage(). 286 * @n_current_limits: Number of selectors available for current limits 287 * 288 * @min_uV: Voltage given by the lowest selector (if linear mapping) 289 * @uV_step: Voltage increase with each selector (if linear mapping) 290 * @linear_min_sel: Minimal selector for starting linear mapping 291 * @fixed_uV: Fixed voltage of rails. 292 * @ramp_delay: Time to settle down after voltage change (unit: uV/us) 293 * @min_dropout_uV: The minimum dropout voltage this regulator can handle 294 * @linear_ranges: A constant table of possible voltage ranges. 295 * @linear_range_selectors_bitfield: A constant table of voltage range 296 * selectors as bitfield values. If 297 * pickable ranges are used each range 298 * must have corresponding selector here. 299 * @n_linear_ranges: Number of entries in the @linear_ranges (and in 300 * linear_range_selectors_bitfield if used) table(s). 301 * @volt_table: Voltage mapping table (if table based mapping) 302 * @curr_table: Current limit mapping table (if table based mapping) 303 * 304 * @vsel_range_reg: Register for range selector when using pickable ranges 305 * and ``regulator_map_*_voltage_*_pickable`` functions. 306 * @vsel_range_mask: Mask for register bitfield used for range selector 307 * @vsel_reg: Register for selector when using ``regulator_map_*_voltage_*`` 308 * @vsel_mask: Mask for register bitfield used for selector 309 * @vsel_step: Specify the resolution of selector stepping when setting 310 * voltage. If 0, then no stepping is done (requested selector is 311 * set directly), if >0 then the regulator API will ramp the 312 * voltage up/down gradually each time increasing/decreasing the 313 * selector by the specified step value. 314 * @csel_reg: Register for current limit selector using regmap set_current_limit 315 * @csel_mask: Mask for register bitfield used for current limit selector 316 * @apply_reg: Register for initiate voltage change on the output when 317 * using regulator_set_voltage_sel_regmap 318 * @apply_bit: Register bitfield used for initiate voltage change on the 319 * output when using regulator_set_voltage_sel_regmap 320 * @enable_reg: Register for control when using regmap enable/disable ops 321 * @enable_mask: Mask for control when using regmap enable/disable ops 322 * @enable_val: Enabling value for control when using regmap enable/disable ops 323 * @disable_val: Disabling value for control when using regmap enable/disable ops 324 * @enable_is_inverted: A flag to indicate set enable_mask bits to disable 325 * when using regulator_enable_regmap and friends APIs. 326 * @bypass_reg: Register for control when using regmap set_bypass 327 * @bypass_mask: Mask for control when using regmap set_bypass 328 * @bypass_val_on: Enabling value for control when using regmap set_bypass 329 * @bypass_val_off: Disabling value for control when using regmap set_bypass 330 * @active_discharge_off: Enabling value for control when using regmap 331 * set_active_discharge 332 * @active_discharge_on: Disabling value for control when using regmap 333 * set_active_discharge 334 * @active_discharge_mask: Mask for control when using regmap 335 * set_active_discharge 336 * @active_discharge_reg: Register for control when using regmap 337 * set_active_discharge 338 * @soft_start_reg: Register for control when using regmap set_soft_start 339 * @soft_start_mask: Mask for control when using regmap set_soft_start 340 * @soft_start_val_on: Enabling value for control when using regmap 341 * set_soft_start 342 * @pull_down_reg: Register for control when using regmap set_pull_down 343 * @pull_down_mask: Mask for control when using regmap set_pull_down 344 * @pull_down_val_on: Enabling value for control when using regmap 345 * set_pull_down 346 * 347 * @ramp_reg: Register for controlling the regulator ramp-rate. 348 * @ramp_mask: Bitmask for the ramp-rate control register. 349 * @ramp_delay_table: Table for mapping the regulator ramp-rate values. Values 350 * should be given in units of V/S (uV/uS). See the 351 * regulator_set_ramp_delay_regmap(). 352 * @n_ramp_values: number of elements at @ramp_delay_table. 353 * 354 * @enable_time: Time taken for initial enable of regulator (in uS). 355 * @off_on_delay: guard time (in uS), before re-enabling a regulator 356 * 357 * @poll_enabled_time: The polling interval (in uS) to use while checking that 358 * the regulator was actually enabled. Max upto enable_time. 359 * 360 * @of_map_mode: Maps a hardware mode defined in a DeviceTree to a standard mode 361 */ 362 struct regulator_desc { 363 const char *name; 364 const char *supply_name; 365 const char *of_match; 366 bool of_match_full_name; 367 const char *regulators_node; 368 int (*of_parse_cb)(struct device_node *, 369 const struct regulator_desc *, 370 struct regulator_config *); 371 int id; 372 unsigned int continuous_voltage_range:1; 373 unsigned n_voltages; 374 unsigned int n_current_limits; 375 const struct regulator_ops *ops; 376 int irq; 377 enum regulator_type type; 378 struct module *owner; 379 380 unsigned int min_uV; 381 unsigned int uV_step; 382 unsigned int linear_min_sel; 383 int fixed_uV; 384 unsigned int ramp_delay; 385 int min_dropout_uV; 386 387 const struct linear_range *linear_ranges; 388 const unsigned int *linear_range_selectors_bitfield; 389 390 int n_linear_ranges; 391 392 const unsigned int *volt_table; 393 const unsigned int *curr_table; 394 395 unsigned int vsel_range_reg; 396 unsigned int vsel_range_mask; 397 unsigned int vsel_reg; 398 unsigned int vsel_mask; 399 unsigned int vsel_step; 400 unsigned int csel_reg; 401 unsigned int csel_mask; 402 unsigned int apply_reg; 403 unsigned int apply_bit; 404 unsigned int enable_reg; 405 unsigned int enable_mask; 406 unsigned int enable_val; 407 unsigned int disable_val; 408 bool enable_is_inverted; 409 unsigned int bypass_reg; 410 unsigned int bypass_mask; 411 unsigned int bypass_val_on; 412 unsigned int bypass_val_off; 413 unsigned int active_discharge_on; 414 unsigned int active_discharge_off; 415 unsigned int active_discharge_mask; 416 unsigned int active_discharge_reg; 417 unsigned int soft_start_reg; 418 unsigned int soft_start_mask; 419 unsigned int soft_start_val_on; 420 unsigned int pull_down_reg; 421 unsigned int pull_down_mask; 422 unsigned int pull_down_val_on; 423 unsigned int ramp_reg; 424 unsigned int ramp_mask; 425 const unsigned int *ramp_delay_table; 426 unsigned int n_ramp_values; 427 428 unsigned int enable_time; 429 430 unsigned int off_on_delay; 431 432 unsigned int poll_enabled_time; 433 434 unsigned int (*of_map_mode)(unsigned int mode); 435 }; 436 437 /** 438 * struct regulator_config - Dynamic regulator descriptor 439 * 440 * Each regulator registered with the core is described with a 441 * structure of this type and a struct regulator_desc. This structure 442 * contains the runtime variable parts of the regulator description. 443 * 444 * @dev: struct device for the regulator 445 * @init_data: platform provided init data, passed through by driver 446 * @driver_data: private regulator data 447 * @of_node: OpenFirmware node to parse for device tree bindings (may be 448 * NULL). 449 * @regmap: regmap to use for core regmap helpers if dev_get_regmap() is 450 * insufficient. 451 * @ena_gpiod: GPIO controlling regulator enable. 452 */ 453 struct regulator_config { 454 struct device *dev; 455 const struct regulator_init_data *init_data; 456 void *driver_data; 457 struct device_node *of_node; 458 struct regmap *regmap; 459 460 struct gpio_desc *ena_gpiod; 461 }; 462 463 /** 464 * struct regulator_err_state - regulator error/notification status 465 * 466 * @rdev: Regulator which status the struct indicates. 467 * @notifs: Events which have occurred on the regulator. 468 * @errors: Errors which are active on the regulator. 469 * @possible_errs: Errors which can be signaled (by given IRQ). 470 */ 471 struct regulator_err_state { 472 struct regulator_dev *rdev; 473 unsigned long notifs; 474 unsigned long errors; 475 int possible_errs; 476 }; 477 478 /** 479 * struct regulator_irq_data - regulator error/notification status data 480 * 481 * @states: Status structs for each of the associated regulators. 482 * @num_states: Amount of associated regulators. 483 * @data: Driver data pointer given at regulator_irq_desc. 484 * @opaque: Value storage for IC driver. Core does not update this. ICs 485 * may want to store status register value here at map_event and 486 * compare contents at 'renable' callback to see if new problems 487 * have been added to status. If that is the case it may be 488 * desirable to return REGULATOR_ERROR_CLEARED and not 489 * REGULATOR_ERROR_ON to allow IRQ fire again and to generate 490 * notifications also for the new issues. 491 * 492 * This structure is passed to 'map_event' and 'renable' callbacks for 493 * reporting regulator status to core. 494 */ 495 struct regulator_irq_data { 496 struct regulator_err_state *states; 497 int num_states; 498 void *data; 499 long opaque; 500 }; 501 502 /** 503 * struct regulator_irq_desc - notification sender for IRQ based events. 504 * 505 * @name: The visible name for the IRQ 506 * @fatal_cnt: If this IRQ is used to signal HW damaging condition it may be 507 * best to shut-down regulator(s) or reboot the SOC if error 508 * handling is repeatedly failing. If fatal_cnt is given the IRQ 509 * handling is aborted if it fails for fatal_cnt times and die() 510 * callback (if populated) is called. If die() is not populated 511 * poweroff for the system is attempted in order to prevent any 512 * further damage. 513 * @reread_ms: The time which is waited before attempting to re-read status 514 * at the worker if IC reading fails. Immediate re-read is done 515 * if time is not specified. 516 * @irq_off_ms: The time which IRQ is kept disabled before re-evaluating the 517 * status for devices which keep IRQ disabled for duration of the 518 * error. If this is not given the IRQ is left enabled and renable 519 * is not called. 520 * @skip_off: If set to true the IRQ handler will attempt to check if any of 521 * the associated regulators are enabled prior to taking other 522 * actions. If no regulators are enabled and this is set to true 523 * a spurious IRQ is assumed and IRQ_NONE is returned. 524 * @high_prio: Boolean to indicate that high priority WQ should be used. 525 * @data: Driver private data pointer which will be passed as such to 526 * the renable, map_event and die callbacks in regulator_irq_data. 527 * @die: Protection callback. If IC status reading or recovery actions 528 * fail fatal_cnt times this callback is called or system is 529 * powered off. This callback should implement a final protection 530 * attempt like disabling the regulator. If protection succeeded 531 * die() may return 0. If anything else is returned the core 532 * assumes final protection failed and attempts to perform a 533 * poweroff as a last resort. 534 * @map_event: Driver callback to map IRQ status into regulator devices with 535 * events / errors. NOTE: callback MUST initialize both the 536 * errors and notifs for all rdevs which it signals having 537 * active events as core does not clean the map data. 538 * REGULATOR_FAILED_RETRY can be returned to indicate that the 539 * status reading from IC failed. If this is repeated for 540 * fatal_cnt times the core will call die() callback or power-off 541 * the system as a last resort to protect the HW. 542 * @renable: Optional callback to check status (if HW supports that) before 543 * re-enabling IRQ. If implemented this should clear the error 544 * flags so that errors fetched by regulator_get_error_flags() 545 * are updated. If callback is not implemented then errors are 546 * assumed to be cleared and IRQ is re-enabled. 547 * REGULATOR_FAILED_RETRY can be returned to 548 * indicate that the status reading from IC failed. If this is 549 * repeated for 'fatal_cnt' times the core will call die() 550 * callback or if die() is not populated then attempt to power-off 551 * the system as a last resort to protect the HW. 552 * Returning zero indicates that the problem in HW has been solved 553 * and IRQ will be re-enabled. Returning REGULATOR_ERROR_ON 554 * indicates the error condition is still active and keeps IRQ 555 * disabled. Please note that returning REGULATOR_ERROR_ON does 556 * not retrigger evaluating what events are active or resending 557 * notifications. If this is needed you probably want to return 558 * zero and allow IRQ to retrigger causing events to be 559 * re-evaluated and re-sent. 560 * 561 * This structure is used for registering regulator IRQ notification helper. 562 */ 563 struct regulator_irq_desc { 564 const char *name; 565 int fatal_cnt; 566 int reread_ms; 567 int irq_off_ms; 568 bool skip_off; 569 bool high_prio; 570 void *data; 571 572 int (*die)(struct regulator_irq_data *rid); 573 int (*map_event)(int irq, struct regulator_irq_data *rid, 574 unsigned long *dev_mask); 575 int (*renable)(struct regulator_irq_data *rid); 576 }; 577 578 /* 579 * Return values for regulator IRQ helpers. 580 */ 581 enum { 582 REGULATOR_ERROR_CLEARED, 583 REGULATOR_FAILED_RETRY, 584 REGULATOR_ERROR_ON, 585 }; 586 587 /* 588 * struct coupling_desc 589 * 590 * Describes coupling of regulators. Each regulator should have 591 * at least a pointer to itself in coupled_rdevs array. 592 * When a new coupled regulator is resolved, n_resolved is 593 * incremented. 594 */ 595 struct coupling_desc { 596 struct regulator_dev **coupled_rdevs; 597 struct regulator_coupler *coupler; 598 int n_resolved; 599 int n_coupled; 600 }; 601 602 /* 603 * struct regulator_dev 604 * 605 * Voltage / Current regulator class device. One for each 606 * regulator. 607 * 608 * This should *not* be used directly by anything except the regulator 609 * core and notification injection (which should take the mutex and do 610 * no other direct access). 611 */ 612 struct regulator_dev { 613 const struct regulator_desc *desc; 614 int exclusive; 615 u32 use_count; 616 u32 open_count; 617 u32 bypass_count; 618 619 /* lists we belong to */ 620 struct list_head list; /* list of all regulators */ 621 622 /* lists we own */ 623 struct list_head consumer_list; /* consumers we supply */ 624 625 struct coupling_desc coupling_desc; 626 627 struct blocking_notifier_head notifier; 628 struct ww_mutex mutex; /* consumer lock */ 629 struct task_struct *mutex_owner; 630 int ref_cnt; 631 struct module *owner; 632 struct device dev; 633 struct regulation_constraints *constraints; 634 struct regulator *supply; /* for tree */ 635 const char *supply_name; 636 struct regmap *regmap; 637 638 struct delayed_work disable_work; 639 640 void *reg_data; /* regulator_dev data */ 641 642 struct dentry *debugfs; 643 644 struct regulator_enable_gpio *ena_pin; 645 unsigned int ena_gpio_state:1; 646 647 unsigned int is_switch:1; 648 649 /* time when this regulator was disabled last time */ 650 ktime_t last_off; 651 int cached_err; 652 bool use_cached_err; 653 spinlock_t err_lock; 654 }; 655 656 /* 657 * Convert error flags to corresponding notifications. 658 * 659 * Can be used by drivers which use the notification helpers to 660 * find out correct notification flags based on the error flags. Drivers 661 * can avoid storing both supported notification and error flags which 662 * may save few bytes. 663 */ 664 static inline int regulator_err2notif(int err) 665 { 666 switch (err) { 667 case REGULATOR_ERROR_UNDER_VOLTAGE: 668 return REGULATOR_EVENT_UNDER_VOLTAGE; 669 case REGULATOR_ERROR_OVER_CURRENT: 670 return REGULATOR_EVENT_OVER_CURRENT; 671 case REGULATOR_ERROR_REGULATION_OUT: 672 return REGULATOR_EVENT_REGULATION_OUT; 673 case REGULATOR_ERROR_FAIL: 674 return REGULATOR_EVENT_FAIL; 675 case REGULATOR_ERROR_OVER_TEMP: 676 return REGULATOR_EVENT_OVER_TEMP; 677 case REGULATOR_ERROR_UNDER_VOLTAGE_WARN: 678 return REGULATOR_EVENT_UNDER_VOLTAGE_WARN; 679 case REGULATOR_ERROR_OVER_CURRENT_WARN: 680 return REGULATOR_EVENT_OVER_CURRENT_WARN; 681 case REGULATOR_ERROR_OVER_VOLTAGE_WARN: 682 return REGULATOR_EVENT_OVER_VOLTAGE_WARN; 683 case REGULATOR_ERROR_OVER_TEMP_WARN: 684 return REGULATOR_EVENT_OVER_TEMP_WARN; 685 } 686 return 0; 687 } 688 689 690 struct regulator_dev * 691 regulator_register(struct device *dev, 692 const struct regulator_desc *regulator_desc, 693 const struct regulator_config *config); 694 struct regulator_dev * 695 devm_regulator_register(struct device *dev, 696 const struct regulator_desc *regulator_desc, 697 const struct regulator_config *config); 698 void regulator_unregister(struct regulator_dev *rdev); 699 700 int regulator_notifier_call_chain(struct regulator_dev *rdev, 701 unsigned long event, void *data); 702 void *devm_regulator_irq_helper(struct device *dev, 703 const struct regulator_irq_desc *d, int irq, 704 int irq_flags, int common_errs, 705 int *per_rdev_errs, struct regulator_dev **rdev, 706 int rdev_amount); 707 void *regulator_irq_helper(struct device *dev, 708 const struct regulator_irq_desc *d, int irq, 709 int irq_flags, int common_errs, int *per_rdev_errs, 710 struct regulator_dev **rdev, int rdev_amount); 711 void regulator_irq_helper_cancel(void **handle); 712 int regulator_irq_map_event_simple(int irq, struct regulator_irq_data *rid, 713 unsigned long *dev_mask); 714 715 void *rdev_get_drvdata(struct regulator_dev *rdev); 716 struct device *rdev_get_dev(struct regulator_dev *rdev); 717 struct regmap *rdev_get_regmap(struct regulator_dev *rdev); 718 int rdev_get_id(struct regulator_dev *rdev); 719 720 int regulator_mode_to_status(unsigned int); 721 722 int regulator_list_voltage_linear(struct regulator_dev *rdev, 723 unsigned int selector); 724 int regulator_list_voltage_pickable_linear_range(struct regulator_dev *rdev, 725 unsigned int selector); 726 int regulator_list_voltage_linear_range(struct regulator_dev *rdev, 727 unsigned int selector); 728 int regulator_list_voltage_table(struct regulator_dev *rdev, 729 unsigned int selector); 730 int regulator_map_voltage_linear(struct regulator_dev *rdev, 731 int min_uV, int max_uV); 732 int regulator_map_voltage_pickable_linear_range(struct regulator_dev *rdev, 733 int min_uV, int max_uV); 734 int regulator_map_voltage_linear_range(struct regulator_dev *rdev, 735 int min_uV, int max_uV); 736 int regulator_map_voltage_iterate(struct regulator_dev *rdev, 737 int min_uV, int max_uV); 738 int regulator_map_voltage_ascend(struct regulator_dev *rdev, 739 int min_uV, int max_uV); 740 int regulator_get_voltage_sel_pickable_regmap(struct regulator_dev *rdev); 741 int regulator_set_voltage_sel_pickable_regmap(struct regulator_dev *rdev, 742 unsigned int sel); 743 int regulator_get_voltage_sel_regmap(struct regulator_dev *rdev); 744 int regulator_set_voltage_sel_regmap(struct regulator_dev *rdev, unsigned sel); 745 int regulator_is_enabled_regmap(struct regulator_dev *rdev); 746 int regulator_enable_regmap(struct regulator_dev *rdev); 747 int regulator_disable_regmap(struct regulator_dev *rdev); 748 int regulator_set_voltage_time_sel(struct regulator_dev *rdev, 749 unsigned int old_selector, 750 unsigned int new_selector); 751 int regulator_set_bypass_regmap(struct regulator_dev *rdev, bool enable); 752 int regulator_get_bypass_regmap(struct regulator_dev *rdev, bool *enable); 753 int regulator_set_soft_start_regmap(struct regulator_dev *rdev); 754 int regulator_set_pull_down_regmap(struct regulator_dev *rdev); 755 756 int regulator_set_active_discharge_regmap(struct regulator_dev *rdev, 757 bool enable); 758 int regulator_set_current_limit_regmap(struct regulator_dev *rdev, 759 int min_uA, int max_uA); 760 int regulator_get_current_limit_regmap(struct regulator_dev *rdev); 761 void *regulator_get_init_drvdata(struct regulator_init_data *reg_init_data); 762 int regulator_find_closest_bigger(unsigned int target, const unsigned int *table, 763 unsigned int num_sel, unsigned int *sel); 764 int regulator_set_ramp_delay_regmap(struct regulator_dev *rdev, int ramp_delay); 765 int regulator_sync_voltage_rdev(struct regulator_dev *rdev); 766 767 /* 768 * Helper functions intended to be used by regulator drivers prior registering 769 * their regulators. 770 */ 771 int regulator_desc_list_voltage_linear_range(const struct regulator_desc *desc, 772 unsigned int selector); 773 774 int regulator_desc_list_voltage_linear(const struct regulator_desc *desc, 775 unsigned int selector); 776 777 #ifdef CONFIG_REGULATOR 778 const char *rdev_get_name(struct regulator_dev *rdev); 779 #else 780 static inline const char *rdev_get_name(struct regulator_dev *rdev) 781 { 782 return NULL; 783 } 784 #endif 785 786 #endif 787