1 /* 2 * driver.h -- SoC Regulator driver support. 3 * 4 * Copyright (C) 2007, 2008 Wolfson Microelectronics PLC. 5 * 6 * Author: Liam Girdwood <lrg@slimlogic.co.uk> 7 * 8 * This program is free software; you can redistribute it and/or modify 9 * it under the terms of the GNU General Public License version 2 as 10 * published by the Free Software Foundation. 11 * 12 * Regulator Driver Interface. 13 */ 14 15 #ifndef __LINUX_REGULATOR_DRIVER_H_ 16 #define __LINUX_REGULATOR_DRIVER_H_ 17 18 #include <linux/device.h> 19 #include <linux/notifier.h> 20 #include <linux/regulator/consumer.h> 21 22 struct regmap; 23 struct regulator_dev; 24 struct regulator_config; 25 struct regulator_init_data; 26 struct regulator_enable_gpio; 27 28 enum regulator_status { 29 REGULATOR_STATUS_OFF, 30 REGULATOR_STATUS_ON, 31 REGULATOR_STATUS_ERROR, 32 /* fast/normal/idle/standby are flavors of "on" */ 33 REGULATOR_STATUS_FAST, 34 REGULATOR_STATUS_NORMAL, 35 REGULATOR_STATUS_IDLE, 36 REGULATOR_STATUS_STANDBY, 37 /* The regulator is enabled but not regulating */ 38 REGULATOR_STATUS_BYPASS, 39 /* in case that any other status doesn't apply */ 40 REGULATOR_STATUS_UNDEFINED, 41 }; 42 43 /** 44 * struct regulator_linear_range - specify linear voltage ranges 45 * 46 * Specify a range of voltages for regulator_map_linar_range() and 47 * regulator_list_linear_range(). 48 * 49 * @min_uV: Lowest voltage in range 50 * @min_sel: Lowest selector for range 51 * @max_sel: Highest selector for range 52 * @uV_step: Step size 53 */ 54 struct regulator_linear_range { 55 unsigned int min_uV; 56 unsigned int min_sel; 57 unsigned int max_sel; 58 unsigned int uV_step; 59 }; 60 61 /* Initialize struct regulator_linear_range */ 62 #define REGULATOR_LINEAR_RANGE(_min_uV, _min_sel, _max_sel, _step_uV) \ 63 { \ 64 .min_uV = _min_uV, \ 65 .min_sel = _min_sel, \ 66 .max_sel = _max_sel, \ 67 .uV_step = _step_uV, \ 68 } 69 70 /** 71 * struct regulator_ops - regulator operations. 72 * 73 * @enable: Configure the regulator as enabled. 74 * @disable: Configure the regulator as disabled. 75 * @is_enabled: Return 1 if the regulator is enabled, 0 if not. 76 * May also return negative errno. 77 * 78 * @set_voltage: Set the voltage for the regulator within the range specified. 79 * The driver should select the voltage closest to min_uV. 80 * @set_voltage_sel: Set the voltage for the regulator using the specified 81 * selector. 82 * @map_voltage: Convert a voltage into a selector 83 * @get_voltage: Return the currently configured voltage for the regulator. 84 * @get_voltage_sel: Return the currently configured voltage selector for the 85 * regulator. 86 * @list_voltage: Return one of the supported voltages, in microvolts; zero 87 * if the selector indicates a voltage that is unusable on this system; 88 * or negative errno. Selectors range from zero to one less than 89 * regulator_desc.n_voltages. Voltages may be reported in any order. 90 * 91 * @set_current_limit: Configure a limit for a current-limited regulator. 92 * The driver should select the current closest to max_uA. 93 * @get_current_limit: Get the configured limit for a current-limited regulator. 94 * 95 * @set_mode: Set the configured operating mode for the regulator. 96 * @get_mode: Get the configured operating mode for the regulator. 97 * @get_status: Return actual (not as-configured) status of regulator, as a 98 * REGULATOR_STATUS value (or negative errno) 99 * @get_optimum_mode: Get the most efficient operating mode for the regulator 100 * when running with the specified parameters. 101 * 102 * @set_bypass: Set the regulator in bypass mode. 103 * @get_bypass: Get the regulator bypass mode state. 104 * 105 * @enable_time: Time taken for the regulator voltage output voltage to 106 * stabilise after being enabled, in microseconds. 107 * @set_ramp_delay: Set the ramp delay for the regulator. The driver should 108 * select ramp delay equal to or less than(closest) ramp_delay. 109 * @set_voltage_time_sel: Time taken for the regulator voltage output voltage 110 * to stabilise after being set to a new value, in microseconds. 111 * The function provides the from and to voltage selector, the 112 * function should return the worst case. 113 * 114 * @set_suspend_voltage: Set the voltage for the regulator when the system 115 * is suspended. 116 * @set_suspend_enable: Mark the regulator as enabled when the system is 117 * suspended. 118 * @set_suspend_disable: Mark the regulator as disabled when the system is 119 * suspended. 120 * @set_suspend_mode: Set the operating mode for the regulator when the 121 * system is suspended. 122 * 123 * This struct describes regulator operations which can be implemented by 124 * regulator chip drivers. 125 */ 126 struct regulator_ops { 127 128 /* enumerate supported voltages */ 129 int (*list_voltage) (struct regulator_dev *, unsigned selector); 130 131 /* get/set regulator voltage */ 132 int (*set_voltage) (struct regulator_dev *, int min_uV, int max_uV, 133 unsigned *selector); 134 int (*map_voltage)(struct regulator_dev *, int min_uV, int max_uV); 135 int (*set_voltage_sel) (struct regulator_dev *, unsigned selector); 136 int (*get_voltage) (struct regulator_dev *); 137 int (*get_voltage_sel) (struct regulator_dev *); 138 139 /* get/set regulator current */ 140 int (*set_current_limit) (struct regulator_dev *, 141 int min_uA, int max_uA); 142 int (*get_current_limit) (struct regulator_dev *); 143 144 /* enable/disable regulator */ 145 int (*enable) (struct regulator_dev *); 146 int (*disable) (struct regulator_dev *); 147 int (*is_enabled) (struct regulator_dev *); 148 149 /* get/set regulator operating mode (defined in consumer.h) */ 150 int (*set_mode) (struct regulator_dev *, unsigned int mode); 151 unsigned int (*get_mode) (struct regulator_dev *); 152 153 /* Time taken to enable or set voltage on the regulator */ 154 int (*enable_time) (struct regulator_dev *); 155 int (*set_ramp_delay) (struct regulator_dev *, int ramp_delay); 156 int (*set_voltage_time_sel) (struct regulator_dev *, 157 unsigned int old_selector, 158 unsigned int new_selector); 159 160 /* report regulator status ... most other accessors report 161 * control inputs, this reports results of combining inputs 162 * from Linux (and other sources) with the actual load. 163 * returns REGULATOR_STATUS_* or negative errno. 164 */ 165 int (*get_status)(struct regulator_dev *); 166 167 /* get most efficient regulator operating mode for load */ 168 unsigned int (*get_optimum_mode) (struct regulator_dev *, int input_uV, 169 int output_uV, int load_uA); 170 171 /* control and report on bypass mode */ 172 int (*set_bypass)(struct regulator_dev *dev, bool enable); 173 int (*get_bypass)(struct regulator_dev *dev, bool *enable); 174 175 /* the operations below are for configuration of regulator state when 176 * its parent PMIC enters a global STANDBY/HIBERNATE state */ 177 178 /* set regulator suspend voltage */ 179 int (*set_suspend_voltage) (struct regulator_dev *, int uV); 180 181 /* enable/disable regulator in suspend state */ 182 int (*set_suspend_enable) (struct regulator_dev *); 183 int (*set_suspend_disable) (struct regulator_dev *); 184 185 /* set regulator suspend operating mode (defined in consumer.h) */ 186 int (*set_suspend_mode) (struct regulator_dev *, unsigned int mode); 187 }; 188 189 /* 190 * Regulators can either control voltage or current. 191 */ 192 enum regulator_type { 193 REGULATOR_VOLTAGE, 194 REGULATOR_CURRENT, 195 }; 196 197 /** 198 * struct regulator_desc - Static regulator descriptor 199 * 200 * Each regulator registered with the core is described with a 201 * structure of this type and a struct regulator_config. This 202 * structure contains the non-varying parts of the regulator 203 * description. 204 * 205 * @name: Identifying name for the regulator. 206 * @supply_name: Identifying the regulator supply 207 * @of_match: Name used to identify regulator in DT. 208 * @regulators_node: Name of node containing regulator definitions in DT. 209 * @of_parse_cb: Optional callback called only if of_match is present. 210 * Will be called for each regulator parsed from DT, during 211 * init_data parsing. 212 * The regulator_config passed as argument to the callback will 213 * be a copy of config passed to regulator_register, valid only 214 * for this particular call. Callback may freely change the 215 * config but it cannot store it for later usage. 216 * Callback should return 0 on success or negative ERRNO 217 * indicating failure. 218 * @id: Numerical identifier for the regulator. 219 * @ops: Regulator operations table. 220 * @irq: Interrupt number for the regulator. 221 * @type: Indicates if the regulator is a voltage or current regulator. 222 * @owner: Module providing the regulator, used for refcounting. 223 * 224 * @continuous_voltage_range: Indicates if the regulator can set any 225 * voltage within constrains range. 226 * @n_voltages: Number of selectors available for ops.list_voltage(). 227 * 228 * @min_uV: Voltage given by the lowest selector (if linear mapping) 229 * @uV_step: Voltage increase with each selector (if linear mapping) 230 * @linear_min_sel: Minimal selector for starting linear mapping 231 * @fixed_uV: Fixed voltage of rails. 232 * @ramp_delay: Time to settle down after voltage change (unit: uV/us) 233 * @linear_ranges: A constant table of possible voltage ranges. 234 * @n_linear_ranges: Number of entries in the @linear_ranges table. 235 * @volt_table: Voltage mapping table (if table based mapping) 236 * 237 * @vsel_reg: Register for selector when using regulator_regmap_X_voltage_ 238 * @vsel_mask: Mask for register bitfield used for selector 239 * @apply_reg: Register for initiate voltage change on the output when 240 * using regulator_set_voltage_sel_regmap 241 * @apply_bit: Register bitfield used for initiate voltage change on the 242 * output when using regulator_set_voltage_sel_regmap 243 * @enable_reg: Register for control when using regmap enable/disable ops 244 * @enable_mask: Mask for control when using regmap enable/disable ops 245 * @enable_val: Enabling value for control when using regmap enable/disable ops 246 * @disable_val: Disabling value for control when using regmap enable/disable ops 247 * @enable_is_inverted: A flag to indicate set enable_mask bits to disable 248 * when using regulator_enable_regmap and friends APIs. 249 * @bypass_reg: Register for control when using regmap set_bypass 250 * @bypass_mask: Mask for control when using regmap set_bypass 251 * @bypass_val_on: Enabling value for control when using regmap set_bypass 252 * @bypass_val_off: Disabling value for control when using regmap set_bypass 253 * 254 * @enable_time: Time taken for initial enable of regulator (in uS). 255 * @off_on_delay: guard time (in uS), before re-enabling a regulator 256 * 257 * @of_map_mode: Maps a hardware mode defined in a DeviceTree to a standard mode 258 */ 259 struct regulator_desc { 260 const char *name; 261 const char *supply_name; 262 const char *of_match; 263 const char *regulators_node; 264 int (*of_parse_cb)(struct device_node *, 265 const struct regulator_desc *, 266 struct regulator_config *); 267 int id; 268 bool continuous_voltage_range; 269 unsigned n_voltages; 270 const struct regulator_ops *ops; 271 int irq; 272 enum regulator_type type; 273 struct module *owner; 274 275 unsigned int min_uV; 276 unsigned int uV_step; 277 unsigned int linear_min_sel; 278 int fixed_uV; 279 unsigned int ramp_delay; 280 281 const struct regulator_linear_range *linear_ranges; 282 int n_linear_ranges; 283 284 const unsigned int *volt_table; 285 286 unsigned int vsel_reg; 287 unsigned int vsel_mask; 288 unsigned int apply_reg; 289 unsigned int apply_bit; 290 unsigned int enable_reg; 291 unsigned int enable_mask; 292 unsigned int enable_val; 293 unsigned int disable_val; 294 bool enable_is_inverted; 295 unsigned int bypass_reg; 296 unsigned int bypass_mask; 297 unsigned int bypass_val_on; 298 unsigned int bypass_val_off; 299 300 unsigned int enable_time; 301 302 unsigned int off_on_delay; 303 304 unsigned int (*of_map_mode)(unsigned int mode); 305 }; 306 307 /** 308 * struct regulator_config - Dynamic regulator descriptor 309 * 310 * Each regulator registered with the core is described with a 311 * structure of this type and a struct regulator_desc. This structure 312 * contains the runtime variable parts of the regulator description. 313 * 314 * @dev: struct device for the regulator 315 * @init_data: platform provided init data, passed through by driver 316 * @driver_data: private regulator data 317 * @of_node: OpenFirmware node to parse for device tree bindings (may be 318 * NULL). 319 * @regmap: regmap to use for core regmap helpers if dev_get_regmap() is 320 * insufficient. 321 * @ena_gpio_initialized: GPIO controlling regulator enable was properly 322 * initialized, meaning that >= 0 is a valid gpio 323 * identifier and < 0 is a non existent gpio. 324 * @ena_gpio: GPIO controlling regulator enable. 325 * @ena_gpio_invert: Sense for GPIO enable control. 326 * @ena_gpio_flags: Flags to use when calling gpio_request_one() 327 */ 328 struct regulator_config { 329 struct device *dev; 330 const struct regulator_init_data *init_data; 331 void *driver_data; 332 struct device_node *of_node; 333 struct regmap *regmap; 334 335 bool ena_gpio_initialized; 336 int ena_gpio; 337 unsigned int ena_gpio_invert:1; 338 unsigned int ena_gpio_flags; 339 }; 340 341 /* 342 * struct regulator_dev 343 * 344 * Voltage / Current regulator class device. One for each 345 * regulator. 346 * 347 * This should *not* be used directly by anything except the regulator 348 * core and notification injection (which should take the mutex and do 349 * no other direct access). 350 */ 351 struct regulator_dev { 352 const struct regulator_desc *desc; 353 int exclusive; 354 u32 use_count; 355 u32 open_count; 356 u32 bypass_count; 357 358 /* lists we belong to */ 359 struct list_head list; /* list of all regulators */ 360 361 /* lists we own */ 362 struct list_head consumer_list; /* consumers we supply */ 363 364 struct blocking_notifier_head notifier; 365 struct mutex mutex; /* consumer lock */ 366 struct module *owner; 367 struct device dev; 368 struct regulation_constraints *constraints; 369 struct regulator *supply; /* for tree */ 370 struct regmap *regmap; 371 372 struct delayed_work disable_work; 373 int deferred_disables; 374 375 void *reg_data; /* regulator_dev data */ 376 377 struct dentry *debugfs; 378 379 struct regulator_enable_gpio *ena_pin; 380 unsigned int ena_gpio_state:1; 381 382 /* time when this regulator was disabled last time */ 383 unsigned long last_off_jiffy; 384 }; 385 386 struct regulator_dev * 387 regulator_register(const struct regulator_desc *regulator_desc, 388 const struct regulator_config *config); 389 struct regulator_dev * 390 devm_regulator_register(struct device *dev, 391 const struct regulator_desc *regulator_desc, 392 const struct regulator_config *config); 393 void regulator_unregister(struct regulator_dev *rdev); 394 void devm_regulator_unregister(struct device *dev, struct regulator_dev *rdev); 395 396 int regulator_notifier_call_chain(struct regulator_dev *rdev, 397 unsigned long event, void *data); 398 399 void *rdev_get_drvdata(struct regulator_dev *rdev); 400 struct device *rdev_get_dev(struct regulator_dev *rdev); 401 int rdev_get_id(struct regulator_dev *rdev); 402 403 int regulator_mode_to_status(unsigned int); 404 405 int regulator_list_voltage_linear(struct regulator_dev *rdev, 406 unsigned int selector); 407 int regulator_list_voltage_linear_range(struct regulator_dev *rdev, 408 unsigned int selector); 409 int regulator_list_voltage_table(struct regulator_dev *rdev, 410 unsigned int selector); 411 int regulator_map_voltage_linear(struct regulator_dev *rdev, 412 int min_uV, int max_uV); 413 int regulator_map_voltage_linear_range(struct regulator_dev *rdev, 414 int min_uV, int max_uV); 415 int regulator_map_voltage_iterate(struct regulator_dev *rdev, 416 int min_uV, int max_uV); 417 int regulator_map_voltage_ascend(struct regulator_dev *rdev, 418 int min_uV, int max_uV); 419 int regulator_get_voltage_sel_regmap(struct regulator_dev *rdev); 420 int regulator_set_voltage_sel_regmap(struct regulator_dev *rdev, unsigned sel); 421 int regulator_is_enabled_regmap(struct regulator_dev *rdev); 422 int regulator_enable_regmap(struct regulator_dev *rdev); 423 int regulator_disable_regmap(struct regulator_dev *rdev); 424 int regulator_set_voltage_time_sel(struct regulator_dev *rdev, 425 unsigned int old_selector, 426 unsigned int new_selector); 427 int regulator_set_bypass_regmap(struct regulator_dev *rdev, bool enable); 428 int regulator_get_bypass_regmap(struct regulator_dev *rdev, bool *enable); 429 430 void *regulator_get_init_drvdata(struct regulator_init_data *reg_init_data); 431 432 #endif 433