1 /* 2 * linux/include/linux/mmc/host.h 3 * 4 * This program is free software; you can redistribute it and/or modify 5 * it under the terms of the GNU General Public License version 2 as 6 * published by the Free Software Foundation. 7 * 8 * Host driver specific definitions. 9 */ 10 #ifndef LINUX_MMC_HOST_H 11 #define LINUX_MMC_HOST_H 12 13 #include <linux/leds.h> 14 #include <linux/mutex.h> 15 #include <linux/timer.h> 16 #include <linux/sched.h> 17 #include <linux/device.h> 18 #include <linux/fault-inject.h> 19 20 #include <linux/mmc/core.h> 21 #include <linux/mmc/card.h> 22 #include <linux/mmc/pm.h> 23 24 struct mmc_ios { 25 unsigned int clock; /* clock rate */ 26 unsigned short vdd; 27 28 /* vdd stores the bit number of the selected voltage range from below. */ 29 30 unsigned char bus_mode; /* command output mode */ 31 32 #define MMC_BUSMODE_OPENDRAIN 1 33 #define MMC_BUSMODE_PUSHPULL 2 34 35 unsigned char chip_select; /* SPI chip select */ 36 37 #define MMC_CS_DONTCARE 0 38 #define MMC_CS_HIGH 1 39 #define MMC_CS_LOW 2 40 41 unsigned char power_mode; /* power supply mode */ 42 43 #define MMC_POWER_OFF 0 44 #define MMC_POWER_UP 1 45 #define MMC_POWER_ON 2 46 #define MMC_POWER_UNDEFINED 3 47 48 unsigned char bus_width; /* data bus width */ 49 50 #define MMC_BUS_WIDTH_1 0 51 #define MMC_BUS_WIDTH_4 2 52 #define MMC_BUS_WIDTH_8 3 53 54 unsigned char timing; /* timing specification used */ 55 56 #define MMC_TIMING_LEGACY 0 57 #define MMC_TIMING_MMC_HS 1 58 #define MMC_TIMING_SD_HS 2 59 #define MMC_TIMING_UHS_SDR12 3 60 #define MMC_TIMING_UHS_SDR25 4 61 #define MMC_TIMING_UHS_SDR50 5 62 #define MMC_TIMING_UHS_SDR104 6 63 #define MMC_TIMING_UHS_DDR50 7 64 #define MMC_TIMING_MMC_DDR52 8 65 #define MMC_TIMING_MMC_HS200 9 66 #define MMC_TIMING_MMC_HS400 10 67 68 unsigned char signal_voltage; /* signalling voltage (1.8V or 3.3V) */ 69 70 #define MMC_SIGNAL_VOLTAGE_330 0 71 #define MMC_SIGNAL_VOLTAGE_180 1 72 #define MMC_SIGNAL_VOLTAGE_120 2 73 74 unsigned char drv_type; /* driver type (A, B, C, D) */ 75 76 #define MMC_SET_DRIVER_TYPE_B 0 77 #define MMC_SET_DRIVER_TYPE_A 1 78 #define MMC_SET_DRIVER_TYPE_C 2 79 #define MMC_SET_DRIVER_TYPE_D 3 80 }; 81 82 struct mmc_host_ops { 83 /* 84 * It is optional for the host to implement pre_req and post_req in 85 * order to support double buffering of requests (prepare one 86 * request while another request is active). 87 * pre_req() must always be followed by a post_req(). 88 * To undo a call made to pre_req(), call post_req() with 89 * a nonzero err condition. 90 */ 91 void (*post_req)(struct mmc_host *host, struct mmc_request *req, 92 int err); 93 void (*pre_req)(struct mmc_host *host, struct mmc_request *req, 94 bool is_first_req); 95 void (*request)(struct mmc_host *host, struct mmc_request *req); 96 97 /* 98 * Avoid calling the next three functions too often or in a "fast 99 * path", since underlaying controller might implement them in an 100 * expensive and/or slow way. Also note that these functions might 101 * sleep, so don't call them in the atomic contexts! 102 */ 103 104 /* 105 * Notes to the set_ios callback: 106 * ios->clock might be 0. For some controllers, setting 0Hz 107 * as any other frequency works. However, some controllers 108 * explicitly need to disable the clock. Otherwise e.g. voltage 109 * switching might fail because the SDCLK is not really quiet. 110 */ 111 void (*set_ios)(struct mmc_host *host, struct mmc_ios *ios); 112 113 /* 114 * Return values for the get_ro callback should be: 115 * 0 for a read/write card 116 * 1 for a read-only card 117 * -ENOSYS when not supported (equal to NULL callback) 118 * or a negative errno value when something bad happened 119 */ 120 int (*get_ro)(struct mmc_host *host); 121 122 /* 123 * Return values for the get_cd callback should be: 124 * 0 for a absent card 125 * 1 for a present card 126 * -ENOSYS when not supported (equal to NULL callback) 127 * or a negative errno value when something bad happened 128 */ 129 int (*get_cd)(struct mmc_host *host); 130 131 void (*enable_sdio_irq)(struct mmc_host *host, int enable); 132 133 /* optional callback for HC quirks */ 134 void (*init_card)(struct mmc_host *host, struct mmc_card *card); 135 136 int (*start_signal_voltage_switch)(struct mmc_host *host, struct mmc_ios *ios); 137 138 /* Check if the card is pulling dat[0:3] low */ 139 int (*card_busy)(struct mmc_host *host); 140 141 /* The tuning command opcode value is different for SD and eMMC cards */ 142 int (*execute_tuning)(struct mmc_host *host, u32 opcode); 143 144 /* Prepare HS400 target operating frequency depending host driver */ 145 int (*prepare_hs400_tuning)(struct mmc_host *host, struct mmc_ios *ios); 146 int (*select_drive_strength)(struct mmc_card *card, 147 unsigned int max_dtr, int host_drv, 148 int card_drv, int *drv_type); 149 void (*hw_reset)(struct mmc_host *host); 150 void (*card_event)(struct mmc_host *host); 151 152 /* 153 * Optional callback to support controllers with HW issues for multiple 154 * I/O. Returns the number of supported blocks for the request. 155 */ 156 int (*multi_io_quirk)(struct mmc_card *card, 157 unsigned int direction, int blk_size); 158 }; 159 160 struct mmc_card; 161 struct device; 162 163 struct mmc_async_req { 164 /* active mmc request */ 165 struct mmc_request *mrq; 166 /* 167 * Check error status of completed mmc request. 168 * Returns 0 if success otherwise non zero. 169 */ 170 int (*err_check) (struct mmc_card *, struct mmc_async_req *); 171 }; 172 173 /** 174 * struct mmc_slot - MMC slot functions 175 * 176 * @cd_irq: MMC/SD-card slot hotplug detection IRQ or -EINVAL 177 * @handler_priv: MMC/SD-card slot context 178 * 179 * Some MMC/SD host controllers implement slot-functions like card and 180 * write-protect detection natively. However, a large number of controllers 181 * leave these functions to the CPU. This struct provides a hook to attach 182 * such slot-function drivers. 183 */ 184 struct mmc_slot { 185 int cd_irq; 186 void *handler_priv; 187 }; 188 189 /** 190 * mmc_context_info - synchronization details for mmc context 191 * @is_done_rcv wake up reason was done request 192 * @is_new_req wake up reason was new request 193 * @is_waiting_last_req mmc context waiting for single running request 194 * @wait wait queue 195 * @lock lock to protect data fields 196 */ 197 struct mmc_context_info { 198 bool is_done_rcv; 199 bool is_new_req; 200 bool is_waiting_last_req; 201 wait_queue_head_t wait; 202 spinlock_t lock; 203 }; 204 205 struct regulator; 206 struct mmc_pwrseq; 207 208 struct mmc_supply { 209 struct regulator *vmmc; /* Card power supply */ 210 struct regulator *vqmmc; /* Optional Vccq supply */ 211 }; 212 213 struct mmc_host { 214 struct device *parent; 215 struct device class_dev; 216 int index; 217 const struct mmc_host_ops *ops; 218 struct mmc_pwrseq *pwrseq; 219 unsigned int f_min; 220 unsigned int f_max; 221 unsigned int f_init; 222 u32 ocr_avail; 223 u32 ocr_avail_sdio; /* SDIO-specific OCR */ 224 u32 ocr_avail_sd; /* SD-specific OCR */ 225 u32 ocr_avail_mmc; /* MMC-specific OCR */ 226 #ifdef CONFIG_PM_SLEEP 227 struct notifier_block pm_notify; 228 #endif 229 u32 max_current_330; 230 u32 max_current_300; 231 u32 max_current_180; 232 233 #define MMC_VDD_165_195 0x00000080 /* VDD voltage 1.65 - 1.95 */ 234 #define MMC_VDD_20_21 0x00000100 /* VDD voltage 2.0 ~ 2.1 */ 235 #define MMC_VDD_21_22 0x00000200 /* VDD voltage 2.1 ~ 2.2 */ 236 #define MMC_VDD_22_23 0x00000400 /* VDD voltage 2.2 ~ 2.3 */ 237 #define MMC_VDD_23_24 0x00000800 /* VDD voltage 2.3 ~ 2.4 */ 238 #define MMC_VDD_24_25 0x00001000 /* VDD voltage 2.4 ~ 2.5 */ 239 #define MMC_VDD_25_26 0x00002000 /* VDD voltage 2.5 ~ 2.6 */ 240 #define MMC_VDD_26_27 0x00004000 /* VDD voltage 2.6 ~ 2.7 */ 241 #define MMC_VDD_27_28 0x00008000 /* VDD voltage 2.7 ~ 2.8 */ 242 #define MMC_VDD_28_29 0x00010000 /* VDD voltage 2.8 ~ 2.9 */ 243 #define MMC_VDD_29_30 0x00020000 /* VDD voltage 2.9 ~ 3.0 */ 244 #define MMC_VDD_30_31 0x00040000 /* VDD voltage 3.0 ~ 3.1 */ 245 #define MMC_VDD_31_32 0x00080000 /* VDD voltage 3.1 ~ 3.2 */ 246 #define MMC_VDD_32_33 0x00100000 /* VDD voltage 3.2 ~ 3.3 */ 247 #define MMC_VDD_33_34 0x00200000 /* VDD voltage 3.3 ~ 3.4 */ 248 #define MMC_VDD_34_35 0x00400000 /* VDD voltage 3.4 ~ 3.5 */ 249 #define MMC_VDD_35_36 0x00800000 /* VDD voltage 3.5 ~ 3.6 */ 250 251 u32 caps; /* Host capabilities */ 252 253 #define MMC_CAP_4_BIT_DATA (1 << 0) /* Can the host do 4 bit transfers */ 254 #define MMC_CAP_MMC_HIGHSPEED (1 << 1) /* Can do MMC high-speed timing */ 255 #define MMC_CAP_SD_HIGHSPEED (1 << 2) /* Can do SD high-speed timing */ 256 #define MMC_CAP_SDIO_IRQ (1 << 3) /* Can signal pending SDIO IRQs */ 257 #define MMC_CAP_SPI (1 << 4) /* Talks only SPI protocols */ 258 #define MMC_CAP_NEEDS_POLL (1 << 5) /* Needs polling for card-detection */ 259 #define MMC_CAP_8_BIT_DATA (1 << 6) /* Can the host do 8 bit transfers */ 260 #define MMC_CAP_AGGRESSIVE_PM (1 << 7) /* Suspend (e)MMC/SD at idle */ 261 #define MMC_CAP_NONREMOVABLE (1 << 8) /* Nonremovable e.g. eMMC */ 262 #define MMC_CAP_WAIT_WHILE_BUSY (1 << 9) /* Waits while card is busy */ 263 #define MMC_CAP_ERASE (1 << 10) /* Allow erase/trim commands */ 264 #define MMC_CAP_1_8V_DDR (1 << 11) /* can support */ 265 /* DDR mode at 1.8V */ 266 #define MMC_CAP_1_2V_DDR (1 << 12) /* can support */ 267 /* DDR mode at 1.2V */ 268 #define MMC_CAP_POWER_OFF_CARD (1 << 13) /* Can power off after boot */ 269 #define MMC_CAP_BUS_WIDTH_TEST (1 << 14) /* CMD14/CMD19 bus width ok */ 270 #define MMC_CAP_UHS_SDR12 (1 << 15) /* Host supports UHS SDR12 mode */ 271 #define MMC_CAP_UHS_SDR25 (1 << 16) /* Host supports UHS SDR25 mode */ 272 #define MMC_CAP_UHS_SDR50 (1 << 17) /* Host supports UHS SDR50 mode */ 273 #define MMC_CAP_UHS_SDR104 (1 << 18) /* Host supports UHS SDR104 mode */ 274 #define MMC_CAP_UHS_DDR50 (1 << 19) /* Host supports UHS DDR50 mode */ 275 #define MMC_CAP_DRIVER_TYPE_A (1 << 23) /* Host supports Driver Type A */ 276 #define MMC_CAP_DRIVER_TYPE_C (1 << 24) /* Host supports Driver Type C */ 277 #define MMC_CAP_DRIVER_TYPE_D (1 << 25) /* Host supports Driver Type D */ 278 #define MMC_CAP_CMD23 (1 << 30) /* CMD23 supported. */ 279 #define MMC_CAP_HW_RESET (1 << 31) /* Hardware reset */ 280 281 u32 caps2; /* More host capabilities */ 282 283 #define MMC_CAP2_BOOTPART_NOACC (1 << 0) /* Boot partition no access */ 284 #define MMC_CAP2_FULL_PWR_CYCLE (1 << 2) /* Can do full power cycle */ 285 #define MMC_CAP2_HS200_1_8V_SDR (1 << 5) /* can support */ 286 #define MMC_CAP2_HS200_1_2V_SDR (1 << 6) /* can support */ 287 #define MMC_CAP2_HS200 (MMC_CAP2_HS200_1_8V_SDR | \ 288 MMC_CAP2_HS200_1_2V_SDR) 289 #define MMC_CAP2_HC_ERASE_SZ (1 << 9) /* High-capacity erase size */ 290 #define MMC_CAP2_CD_ACTIVE_HIGH (1 << 10) /* Card-detect signal active high */ 291 #define MMC_CAP2_RO_ACTIVE_HIGH (1 << 11) /* Write-protect signal active high */ 292 #define MMC_CAP2_PACKED_RD (1 << 12) /* Allow packed read */ 293 #define MMC_CAP2_PACKED_WR (1 << 13) /* Allow packed write */ 294 #define MMC_CAP2_PACKED_CMD (MMC_CAP2_PACKED_RD | \ 295 MMC_CAP2_PACKED_WR) 296 #define MMC_CAP2_NO_PRESCAN_POWERUP (1 << 14) /* Don't power up before scan */ 297 #define MMC_CAP2_HS400_1_8V (1 << 15) /* Can support HS400 1.8V */ 298 #define MMC_CAP2_HS400_1_2V (1 << 16) /* Can support HS400 1.2V */ 299 #define MMC_CAP2_HS400 (MMC_CAP2_HS400_1_8V | \ 300 MMC_CAP2_HS400_1_2V) 301 #define MMC_CAP2_HSX00_1_2V (MMC_CAP2_HS200_1_2V_SDR | MMC_CAP2_HS400_1_2V) 302 #define MMC_CAP2_SDIO_IRQ_NOTHREAD (1 << 17) 303 #define MMC_CAP2_NO_WRITE_PROTECT (1 << 18) /* No physical write protect pin, assume that card is always read-write */ 304 #define MMC_CAP2_NO_SDIO (1 << 19) /* Do not send SDIO commands during initialization */ 305 306 mmc_pm_flag_t pm_caps; /* supported pm features */ 307 308 /* host specific block data */ 309 unsigned int max_seg_size; /* see blk_queue_max_segment_size */ 310 unsigned short max_segs; /* see blk_queue_max_segments */ 311 unsigned short unused; 312 unsigned int max_req_size; /* maximum number of bytes in one req */ 313 unsigned int max_blk_size; /* maximum size of one mmc block */ 314 unsigned int max_blk_count; /* maximum number of blocks in one req */ 315 unsigned int max_busy_timeout; /* max busy timeout in ms */ 316 317 /* private data */ 318 spinlock_t lock; /* lock for claim and bus ops */ 319 320 struct mmc_ios ios; /* current io bus settings */ 321 322 /* group bitfields together to minimize padding */ 323 unsigned int use_spi_crc:1; 324 unsigned int claimed:1; /* host exclusively claimed */ 325 unsigned int bus_dead:1; /* bus has been released */ 326 #ifdef CONFIG_MMC_DEBUG 327 unsigned int removed:1; /* host is being removed */ 328 #endif 329 unsigned int can_retune:1; /* re-tuning can be used */ 330 unsigned int doing_retune:1; /* re-tuning in progress */ 331 unsigned int retune_now:1; /* do re-tuning at next req */ 332 unsigned int retune_paused:1; /* re-tuning is temporarily disabled */ 333 334 int rescan_disable; /* disable card detection */ 335 int rescan_entered; /* used with nonremovable devices */ 336 337 int need_retune; /* re-tuning is needed */ 338 int hold_retune; /* hold off re-tuning */ 339 unsigned int retune_period; /* re-tuning period in secs */ 340 struct timer_list retune_timer; /* for periodic re-tuning */ 341 342 bool trigger_card_event; /* card_event necessary */ 343 344 struct mmc_card *card; /* device attached to this host */ 345 346 wait_queue_head_t wq; 347 struct task_struct *claimer; /* task that has host claimed */ 348 int claim_cnt; /* "claim" nesting count */ 349 350 struct delayed_work detect; 351 int detect_change; /* card detect flag */ 352 struct mmc_slot slot; 353 354 const struct mmc_bus_ops *bus_ops; /* current bus driver */ 355 unsigned int bus_refs; /* reference counter */ 356 357 unsigned int sdio_irqs; 358 struct task_struct *sdio_irq_thread; 359 bool sdio_irq_pending; 360 atomic_t sdio_irq_thread_abort; 361 362 mmc_pm_flag_t pm_flags; /* requested pm features */ 363 364 struct led_trigger *led; /* activity led */ 365 366 #ifdef CONFIG_REGULATOR 367 bool regulator_enabled; /* regulator state */ 368 #endif 369 struct mmc_supply supply; 370 371 struct dentry *debugfs_root; 372 373 struct mmc_async_req *areq; /* active async req */ 374 struct mmc_context_info context_info; /* async synchronization info */ 375 376 #ifdef CONFIG_FAIL_MMC_REQUEST 377 struct fault_attr fail_mmc_request; 378 #endif 379 380 unsigned int actual_clock; /* Actual HC clock rate */ 381 382 unsigned int slotno; /* used for sdio acpi binding */ 383 384 int dsr_req; /* DSR value is valid */ 385 u32 dsr; /* optional driver stage (DSR) value */ 386 387 unsigned long private[0] ____cacheline_aligned; 388 }; 389 390 struct mmc_host *mmc_alloc_host(int extra, struct device *); 391 int mmc_add_host(struct mmc_host *); 392 void mmc_remove_host(struct mmc_host *); 393 void mmc_free_host(struct mmc_host *); 394 int mmc_of_parse(struct mmc_host *host); 395 396 static inline void *mmc_priv(struct mmc_host *host) 397 { 398 return (void *)host->private; 399 } 400 401 #define mmc_host_is_spi(host) ((host)->caps & MMC_CAP_SPI) 402 403 #define mmc_dev(x) ((x)->parent) 404 #define mmc_classdev(x) (&(x)->class_dev) 405 #define mmc_hostname(x) (dev_name(&(x)->class_dev)) 406 407 int mmc_power_save_host(struct mmc_host *host); 408 int mmc_power_restore_host(struct mmc_host *host); 409 410 void mmc_detect_change(struct mmc_host *, unsigned long delay); 411 void mmc_request_done(struct mmc_host *, struct mmc_request *); 412 413 static inline void mmc_signal_sdio_irq(struct mmc_host *host) 414 { 415 host->ops->enable_sdio_irq(host, 0); 416 host->sdio_irq_pending = true; 417 if (host->sdio_irq_thread) 418 wake_up_process(host->sdio_irq_thread); 419 } 420 421 void sdio_run_irqs(struct mmc_host *host); 422 423 #ifdef CONFIG_REGULATOR 424 int mmc_regulator_get_ocrmask(struct regulator *supply); 425 int mmc_regulator_set_ocr(struct mmc_host *mmc, 426 struct regulator *supply, 427 unsigned short vdd_bit); 428 int mmc_regulator_set_vqmmc(struct mmc_host *mmc, struct mmc_ios *ios); 429 #else 430 static inline int mmc_regulator_get_ocrmask(struct regulator *supply) 431 { 432 return 0; 433 } 434 435 static inline int mmc_regulator_set_ocr(struct mmc_host *mmc, 436 struct regulator *supply, 437 unsigned short vdd_bit) 438 { 439 return 0; 440 } 441 442 static inline int mmc_regulator_set_vqmmc(struct mmc_host *mmc, 443 struct mmc_ios *ios) 444 { 445 return -EINVAL; 446 } 447 #endif 448 449 int mmc_regulator_get_supply(struct mmc_host *mmc); 450 451 static inline int mmc_card_is_removable(struct mmc_host *host) 452 { 453 return !(host->caps & MMC_CAP_NONREMOVABLE); 454 } 455 456 static inline int mmc_card_keep_power(struct mmc_host *host) 457 { 458 return host->pm_flags & MMC_PM_KEEP_POWER; 459 } 460 461 static inline int mmc_card_wake_sdio_irq(struct mmc_host *host) 462 { 463 return host->pm_flags & MMC_PM_WAKE_SDIO_IRQ; 464 } 465 466 static inline int mmc_host_cmd23(struct mmc_host *host) 467 { 468 return host->caps & MMC_CAP_CMD23; 469 } 470 471 static inline int mmc_boot_partition_access(struct mmc_host *host) 472 { 473 return !(host->caps2 & MMC_CAP2_BOOTPART_NOACC); 474 } 475 476 static inline int mmc_host_uhs(struct mmc_host *host) 477 { 478 return host->caps & 479 (MMC_CAP_UHS_SDR12 | MMC_CAP_UHS_SDR25 | 480 MMC_CAP_UHS_SDR50 | MMC_CAP_UHS_SDR104 | 481 MMC_CAP_UHS_DDR50); 482 } 483 484 static inline int mmc_host_packed_wr(struct mmc_host *host) 485 { 486 return host->caps2 & MMC_CAP2_PACKED_WR; 487 } 488 489 static inline int mmc_card_hs(struct mmc_card *card) 490 { 491 return card->host->ios.timing == MMC_TIMING_SD_HS || 492 card->host->ios.timing == MMC_TIMING_MMC_HS; 493 } 494 495 static inline int mmc_card_uhs(struct mmc_card *card) 496 { 497 return card->host->ios.timing >= MMC_TIMING_UHS_SDR12 && 498 card->host->ios.timing <= MMC_TIMING_UHS_DDR50; 499 } 500 501 static inline bool mmc_card_hs200(struct mmc_card *card) 502 { 503 return card->host->ios.timing == MMC_TIMING_MMC_HS200; 504 } 505 506 static inline bool mmc_card_ddr52(struct mmc_card *card) 507 { 508 return card->host->ios.timing == MMC_TIMING_MMC_DDR52; 509 } 510 511 static inline bool mmc_card_hs400(struct mmc_card *card) 512 { 513 return card->host->ios.timing == MMC_TIMING_MMC_HS400; 514 } 515 516 void mmc_retune_timer_stop(struct mmc_host *host); 517 518 static inline void mmc_retune_needed(struct mmc_host *host) 519 { 520 if (host->can_retune) 521 host->need_retune = 1; 522 } 523 524 static inline void mmc_retune_recheck(struct mmc_host *host) 525 { 526 if (host->hold_retune <= 1) 527 host->retune_now = 1; 528 } 529 530 void mmc_retune_pause(struct mmc_host *host); 531 void mmc_retune_unpause(struct mmc_host *host); 532 533 #endif /* LINUX_MMC_HOST_H */ 534