1 /* 2 * Xilinx TFT frame buffer driver 3 * 4 * Author: MontaVista Software, Inc. 5 * source@mvista.com 6 * 7 * 2002-2007 (c) MontaVista Software, Inc. 8 * 2007 (c) Secret Lab Technologies, Ltd. 9 * 2009 (c) Xilinx Inc. 10 * 11 * This file is licensed under the terms of the GNU General Public License 12 * version 2. This program is licensed "as is" without any warranty of any 13 * kind, whether express or implied. 14 */ 15 16 /* 17 * This driver was based on au1100fb.c by MontaVista rewritten for 2.6 18 * by Embedded Alley Solutions <source@embeddedalley.com>, which in turn 19 * was based on skeletonfb.c, Skeleton for a frame buffer device by 20 * Geert Uytterhoeven. 21 */ 22 23 #include <linux/device.h> 24 #include <linux/module.h> 25 #include <linux/kernel.h> 26 #include <linux/errno.h> 27 #include <linux/string.h> 28 #include <linux/mm.h> 29 #include <linux/fb.h> 30 #include <linux/init.h> 31 #include <linux/dma-mapping.h> 32 #include <linux/of_device.h> 33 #include <linux/of_platform.h> 34 #include <linux/of_address.h> 35 #include <linux/io.h> 36 #include <linux/slab.h> 37 38 #ifdef CONFIG_PPC_DCR 39 #include <asm/dcr.h> 40 #endif 41 42 #define DRIVER_NAME "xilinxfb" 43 44 45 /* 46 * Xilinx calls it "TFT LCD Controller" though it can also be used for 47 * the VGA port on the Xilinx ML40x board. This is a hardware display 48 * controller for a 640x480 resolution TFT or VGA screen. 49 * 50 * The interface to the framebuffer is nice and simple. There are two 51 * control registers. The first tells the LCD interface where in memory 52 * the frame buffer is (only the 11 most significant bits are used, so 53 * don't start thinking about scrolling). The second allows the LCD to 54 * be turned on or off as well as rotated 180 degrees. 55 * 56 * In case of direct BUS access the second control register will be at 57 * an offset of 4 as compared to the DCR access where the offset is 1 58 * i.e. REG_CTRL. So this is taken care in the function 59 * xilinx_fb_out32 where it left shifts the offset 2 times in case of 60 * direct BUS access. 61 */ 62 #define NUM_REGS 2 63 #define REG_FB_ADDR 0 64 #define REG_CTRL 1 65 #define REG_CTRL_ENABLE 0x0001 66 #define REG_CTRL_ROTATE 0x0002 67 68 /* 69 * The hardware only handles a single mode: 640x480 24 bit true 70 * color. Each pixel gets a word (32 bits) of memory. Within each word, 71 * the 8 most significant bits are ignored, the next 8 bits are the red 72 * level, the next 8 bits are the green level and the 8 least 73 * significant bits are the blue level. Each row of the LCD uses 1024 74 * words, but only the first 640 pixels are displayed with the other 384 75 * words being ignored. There are 480 rows. 76 */ 77 #define BYTES_PER_PIXEL 4 78 #define BITS_PER_PIXEL (BYTES_PER_PIXEL * 8) 79 80 #define RED_SHIFT 16 81 #define GREEN_SHIFT 8 82 #define BLUE_SHIFT 0 83 84 #define PALETTE_ENTRIES_NO 16 /* passed to fb_alloc_cmap() */ 85 86 /* ML300/403 reference design framebuffer driver platform data struct */ 87 struct xilinxfb_platform_data { 88 u32 rotate_screen; /* Flag to rotate display 180 degrees */ 89 u32 screen_height_mm; /* Physical dimensions of screen in mm */ 90 u32 screen_width_mm; 91 u32 xres, yres; /* resolution of screen in pixels */ 92 u32 xvirt, yvirt; /* resolution of memory buffer */ 93 94 /* Physical address of framebuffer memory; If non-zero, driver 95 * will use provided memory address instead of allocating one from 96 * the consistent pool. */ 97 u32 fb_phys; 98 }; 99 100 /* 101 * Default xilinxfb configuration 102 */ 103 static struct xilinxfb_platform_data xilinx_fb_default_pdata = { 104 .xres = 640, 105 .yres = 480, 106 .xvirt = 1024, 107 .yvirt = 480, 108 }; 109 110 /* 111 * Here are the default fb_fix_screeninfo and fb_var_screeninfo structures 112 */ 113 static struct fb_fix_screeninfo xilinx_fb_fix = { 114 .id = "Xilinx", 115 .type = FB_TYPE_PACKED_PIXELS, 116 .visual = FB_VISUAL_TRUECOLOR, 117 .accel = FB_ACCEL_NONE 118 }; 119 120 static struct fb_var_screeninfo xilinx_fb_var = { 121 .bits_per_pixel = BITS_PER_PIXEL, 122 123 .red = { RED_SHIFT, 8, 0 }, 124 .green = { GREEN_SHIFT, 8, 0 }, 125 .blue = { BLUE_SHIFT, 8, 0 }, 126 .transp = { 0, 0, 0 }, 127 128 .activate = FB_ACTIVATE_NOW 129 }; 130 131 132 #define BUS_ACCESS_FLAG 0x1 /* 1 = BUS, 0 = DCR */ 133 #define LITTLE_ENDIAN_ACCESS 0x2 /* LITTLE ENDIAN IO functions */ 134 135 struct xilinxfb_drvdata { 136 137 struct fb_info info; /* FB driver info record */ 138 139 phys_addr_t regs_phys; /* phys. address of the control 140 registers */ 141 void __iomem *regs; /* virt. address of the control 142 registers */ 143 #ifdef CONFIG_PPC_DCR 144 dcr_host_t dcr_host; 145 unsigned int dcr_len; 146 #endif 147 void *fb_virt; /* virt. address of the frame buffer */ 148 dma_addr_t fb_phys; /* phys. address of the frame buffer */ 149 int fb_alloced; /* Flag, was the fb memory alloced? */ 150 151 u8 flags; /* features of the driver */ 152 153 u32 reg_ctrl_default; 154 155 u32 pseudo_palette[PALETTE_ENTRIES_NO]; 156 /* Fake palette of 16 colors */ 157 }; 158 159 #define to_xilinxfb_drvdata(_info) \ 160 container_of(_info, struct xilinxfb_drvdata, info) 161 162 /* 163 * The XPS TFT Controller can be accessed through BUS or DCR interface. 164 * To perform the read/write on the registers we need to check on 165 * which bus its connected and call the appropriate write API. 166 */ 167 static void xilinx_fb_out32(struct xilinxfb_drvdata *drvdata, u32 offset, 168 u32 val) 169 { 170 if (drvdata->flags & BUS_ACCESS_FLAG) { 171 if (drvdata->flags & LITTLE_ENDIAN_ACCESS) 172 iowrite32(val, drvdata->regs + (offset << 2)); 173 else 174 iowrite32be(val, drvdata->regs + (offset << 2)); 175 } 176 #ifdef CONFIG_PPC_DCR 177 else 178 dcr_write(drvdata->dcr_host, offset, val); 179 #endif 180 } 181 182 static u32 xilinx_fb_in32(struct xilinxfb_drvdata *drvdata, u32 offset) 183 { 184 if (drvdata->flags & BUS_ACCESS_FLAG) { 185 if (drvdata->flags & LITTLE_ENDIAN_ACCESS) 186 return ioread32(drvdata->regs + (offset << 2)); 187 else 188 return ioread32be(drvdata->regs + (offset << 2)); 189 } 190 #ifdef CONFIG_PPC_DCR 191 else 192 return dcr_read(drvdata->dcr_host, offset); 193 #endif 194 return 0; 195 } 196 197 static int 198 xilinx_fb_setcolreg(unsigned regno, unsigned red, unsigned green, unsigned blue, 199 unsigned transp, struct fb_info *fbi) 200 { 201 u32 *palette = fbi->pseudo_palette; 202 203 if (regno >= PALETTE_ENTRIES_NO) 204 return -EINVAL; 205 206 if (fbi->var.grayscale) { 207 /* Convert color to grayscale. 208 * grayscale = 0.30*R + 0.59*G + 0.11*B */ 209 red = green = blue = 210 (red * 77 + green * 151 + blue * 28 + 127) >> 8; 211 } 212 213 /* fbi->fix.visual is always FB_VISUAL_TRUECOLOR */ 214 215 /* We only handle 8 bits of each color. */ 216 red >>= 8; 217 green >>= 8; 218 blue >>= 8; 219 palette[regno] = (red << RED_SHIFT) | (green << GREEN_SHIFT) | 220 (blue << BLUE_SHIFT); 221 222 return 0; 223 } 224 225 static int 226 xilinx_fb_blank(int blank_mode, struct fb_info *fbi) 227 { 228 struct xilinxfb_drvdata *drvdata = to_xilinxfb_drvdata(fbi); 229 230 switch (blank_mode) { 231 case FB_BLANK_UNBLANK: 232 /* turn on panel */ 233 xilinx_fb_out32(drvdata, REG_CTRL, drvdata->reg_ctrl_default); 234 break; 235 236 case FB_BLANK_NORMAL: 237 case FB_BLANK_VSYNC_SUSPEND: 238 case FB_BLANK_HSYNC_SUSPEND: 239 case FB_BLANK_POWERDOWN: 240 /* turn off panel */ 241 xilinx_fb_out32(drvdata, REG_CTRL, 0); 242 default: 243 break; 244 245 } 246 return 0; /* success */ 247 } 248 249 static struct fb_ops xilinxfb_ops = 250 { 251 .owner = THIS_MODULE, 252 .fb_setcolreg = xilinx_fb_setcolreg, 253 .fb_blank = xilinx_fb_blank, 254 .fb_fillrect = cfb_fillrect, 255 .fb_copyarea = cfb_copyarea, 256 .fb_imageblit = cfb_imageblit, 257 }; 258 259 /* --------------------------------------------------------------------- 260 * Bus independent setup/teardown 261 */ 262 263 static int xilinxfb_assign(struct platform_device *pdev, 264 struct xilinxfb_drvdata *drvdata, 265 struct xilinxfb_platform_data *pdata) 266 { 267 int rc; 268 struct device *dev = &pdev->dev; 269 int fbsize = pdata->xvirt * pdata->yvirt * BYTES_PER_PIXEL; 270 271 if (drvdata->flags & BUS_ACCESS_FLAG) { 272 struct resource *res; 273 274 res = platform_get_resource(pdev, IORESOURCE_MEM, 0); 275 drvdata->regs = devm_ioremap_resource(&pdev->dev, res); 276 if (IS_ERR(drvdata->regs)) 277 return PTR_ERR(drvdata->regs); 278 279 drvdata->regs_phys = res->start; 280 } 281 282 /* Allocate the framebuffer memory */ 283 if (pdata->fb_phys) { 284 drvdata->fb_phys = pdata->fb_phys; 285 drvdata->fb_virt = ioremap(pdata->fb_phys, fbsize); 286 } else { 287 drvdata->fb_alloced = 1; 288 drvdata->fb_virt = dma_alloc_coherent(dev, PAGE_ALIGN(fbsize), 289 &drvdata->fb_phys, GFP_KERNEL); 290 } 291 292 if (!drvdata->fb_virt) { 293 dev_err(dev, "Could not allocate frame buffer memory\n"); 294 return -ENOMEM; 295 } 296 297 /* Clear (turn to black) the framebuffer */ 298 memset_io((void __iomem *)drvdata->fb_virt, 0, fbsize); 299 300 /* Tell the hardware where the frame buffer is */ 301 xilinx_fb_out32(drvdata, REG_FB_ADDR, drvdata->fb_phys); 302 rc = xilinx_fb_in32(drvdata, REG_FB_ADDR); 303 /* Endianess detection */ 304 if (rc != drvdata->fb_phys) { 305 drvdata->flags |= LITTLE_ENDIAN_ACCESS; 306 xilinx_fb_out32(drvdata, REG_FB_ADDR, drvdata->fb_phys); 307 } 308 309 /* Turn on the display */ 310 drvdata->reg_ctrl_default = REG_CTRL_ENABLE; 311 if (pdata->rotate_screen) 312 drvdata->reg_ctrl_default |= REG_CTRL_ROTATE; 313 xilinx_fb_out32(drvdata, REG_CTRL, 314 drvdata->reg_ctrl_default); 315 316 /* Fill struct fb_info */ 317 drvdata->info.device = dev; 318 drvdata->info.screen_base = (void __iomem *)drvdata->fb_virt; 319 drvdata->info.fbops = &xilinxfb_ops; 320 drvdata->info.fix = xilinx_fb_fix; 321 drvdata->info.fix.smem_start = drvdata->fb_phys; 322 drvdata->info.fix.smem_len = fbsize; 323 drvdata->info.fix.line_length = pdata->xvirt * BYTES_PER_PIXEL; 324 325 drvdata->info.pseudo_palette = drvdata->pseudo_palette; 326 drvdata->info.flags = FBINFO_DEFAULT; 327 drvdata->info.var = xilinx_fb_var; 328 drvdata->info.var.height = pdata->screen_height_mm; 329 drvdata->info.var.width = pdata->screen_width_mm; 330 drvdata->info.var.xres = pdata->xres; 331 drvdata->info.var.yres = pdata->yres; 332 drvdata->info.var.xres_virtual = pdata->xvirt; 333 drvdata->info.var.yres_virtual = pdata->yvirt; 334 335 /* Allocate a colour map */ 336 rc = fb_alloc_cmap(&drvdata->info.cmap, PALETTE_ENTRIES_NO, 0); 337 if (rc) { 338 dev_err(dev, "Fail to allocate colormap (%d entries)\n", 339 PALETTE_ENTRIES_NO); 340 goto err_cmap; 341 } 342 343 /* Register new frame buffer */ 344 rc = register_framebuffer(&drvdata->info); 345 if (rc) { 346 dev_err(dev, "Could not register frame buffer\n"); 347 goto err_regfb; 348 } 349 350 if (drvdata->flags & BUS_ACCESS_FLAG) { 351 /* Put a banner in the log (for DEBUG) */ 352 dev_dbg(dev, "regs: phys=%pa, virt=%p\n", 353 &drvdata->regs_phys, drvdata->regs); 354 } 355 /* Put a banner in the log (for DEBUG) */ 356 dev_dbg(dev, "fb: phys=%llx, virt=%p, size=%x\n", 357 (unsigned long long)drvdata->fb_phys, drvdata->fb_virt, fbsize); 358 359 return 0; /* success */ 360 361 err_regfb: 362 fb_dealloc_cmap(&drvdata->info.cmap); 363 364 err_cmap: 365 if (drvdata->fb_alloced) 366 dma_free_coherent(dev, PAGE_ALIGN(fbsize), drvdata->fb_virt, 367 drvdata->fb_phys); 368 else 369 iounmap(drvdata->fb_virt); 370 371 /* Turn off the display */ 372 xilinx_fb_out32(drvdata, REG_CTRL, 0); 373 374 return rc; 375 } 376 377 static int xilinxfb_release(struct device *dev) 378 { 379 struct xilinxfb_drvdata *drvdata = dev_get_drvdata(dev); 380 381 #if !defined(CONFIG_FRAMEBUFFER_CONSOLE) && defined(CONFIG_LOGO) 382 xilinx_fb_blank(VESA_POWERDOWN, &drvdata->info); 383 #endif 384 385 unregister_framebuffer(&drvdata->info); 386 387 fb_dealloc_cmap(&drvdata->info.cmap); 388 389 if (drvdata->fb_alloced) 390 dma_free_coherent(dev, PAGE_ALIGN(drvdata->info.fix.smem_len), 391 drvdata->fb_virt, drvdata->fb_phys); 392 else 393 iounmap(drvdata->fb_virt); 394 395 /* Turn off the display */ 396 xilinx_fb_out32(drvdata, REG_CTRL, 0); 397 398 #ifdef CONFIG_PPC_DCR 399 /* Release the resources, as allocated based on interface */ 400 if (!(drvdata->flags & BUS_ACCESS_FLAG)) 401 dcr_unmap(drvdata->dcr_host, drvdata->dcr_len); 402 #endif 403 404 return 0; 405 } 406 407 /* --------------------------------------------------------------------- 408 * OF bus binding 409 */ 410 411 static int xilinxfb_of_probe(struct platform_device *pdev) 412 { 413 const u32 *prop; 414 u32 tft_access = 0; 415 struct xilinxfb_platform_data pdata; 416 int size; 417 struct xilinxfb_drvdata *drvdata; 418 419 /* Copy with the default pdata (not a ptr reference!) */ 420 pdata = xilinx_fb_default_pdata; 421 422 /* Allocate the driver data region */ 423 drvdata = devm_kzalloc(&pdev->dev, sizeof(*drvdata), GFP_KERNEL); 424 if (!drvdata) 425 return -ENOMEM; 426 427 /* 428 * To check whether the core is connected directly to DCR or BUS 429 * interface and initialize the tft_access accordingly. 430 */ 431 of_property_read_u32(pdev->dev.of_node, "xlnx,dcr-splb-slave-if", 432 &tft_access); 433 434 /* 435 * Fill the resource structure if its direct BUS interface 436 * otherwise fill the dcr_host structure. 437 */ 438 if (tft_access) { 439 drvdata->flags |= BUS_ACCESS_FLAG; 440 } 441 #ifdef CONFIG_PPC_DCR 442 else { 443 int start; 444 start = dcr_resource_start(pdev->dev.of_node, 0); 445 drvdata->dcr_len = dcr_resource_len(pdev->dev.of_node, 0); 446 drvdata->dcr_host = dcr_map(pdev->dev.of_node, start, drvdata->dcr_len); 447 if (!DCR_MAP_OK(drvdata->dcr_host)) { 448 dev_err(&pdev->dev, "invalid DCR address\n"); 449 return -ENODEV; 450 } 451 } 452 #endif 453 454 prop = of_get_property(pdev->dev.of_node, "phys-size", &size); 455 if ((prop) && (size >= sizeof(u32)*2)) { 456 pdata.screen_width_mm = prop[0]; 457 pdata.screen_height_mm = prop[1]; 458 } 459 460 prop = of_get_property(pdev->dev.of_node, "resolution", &size); 461 if ((prop) && (size >= sizeof(u32)*2)) { 462 pdata.xres = prop[0]; 463 pdata.yres = prop[1]; 464 } 465 466 prop = of_get_property(pdev->dev.of_node, "virtual-resolution", &size); 467 if ((prop) && (size >= sizeof(u32)*2)) { 468 pdata.xvirt = prop[0]; 469 pdata.yvirt = prop[1]; 470 } 471 472 if (of_find_property(pdev->dev.of_node, "rotate-display", NULL)) 473 pdata.rotate_screen = 1; 474 475 dev_set_drvdata(&pdev->dev, drvdata); 476 return xilinxfb_assign(pdev, drvdata, &pdata); 477 } 478 479 static int xilinxfb_of_remove(struct platform_device *op) 480 { 481 return xilinxfb_release(&op->dev); 482 } 483 484 /* Match table for of_platform binding */ 485 static struct of_device_id xilinxfb_of_match[] = { 486 { .compatible = "xlnx,xps-tft-1.00.a", }, 487 { .compatible = "xlnx,xps-tft-2.00.a", }, 488 { .compatible = "xlnx,xps-tft-2.01.a", }, 489 { .compatible = "xlnx,plb-tft-cntlr-ref-1.00.a", }, 490 { .compatible = "xlnx,plb-dvi-cntlr-ref-1.00.c", }, 491 {}, 492 }; 493 MODULE_DEVICE_TABLE(of, xilinxfb_of_match); 494 495 static struct platform_driver xilinxfb_of_driver = { 496 .probe = xilinxfb_of_probe, 497 .remove = xilinxfb_of_remove, 498 .driver = { 499 .name = DRIVER_NAME, 500 .owner = THIS_MODULE, 501 .of_match_table = xilinxfb_of_match, 502 }, 503 }; 504 505 module_platform_driver(xilinxfb_of_driver); 506 507 MODULE_AUTHOR("MontaVista Software, Inc. <source@mvista.com>"); 508 MODULE_DESCRIPTION("Xilinx TFT frame buffer driver"); 509 MODULE_LICENSE("GPL"); 510