1 // SPDX-License-Identifier: GPL-2.0 2 3 /* 4 * ATI Mach64 CT/VT/GT/LT Support 5 */ 6 7 #include <linux/fb.h> 8 #include <linux/delay.h> 9 #include <asm/io.h> 10 #include <video/mach64.h> 11 #include "atyfb.h" 12 #ifdef CONFIG_PPC 13 #include <asm/machdep.h> 14 #endif 15 16 #undef DEBUG 17 18 static int aty_valid_pll_ct (const struct fb_info *info, u32 vclk_per, struct pll_ct *pll); 19 static int aty_dsp_gt (const struct fb_info *info, u32 bpp, struct pll_ct *pll); 20 static int aty_var_to_pll_ct(const struct fb_info *info, u32 vclk_per, u32 bpp, union aty_pll *pll); 21 static u32 aty_pll_to_var_ct(const struct fb_info *info, const union aty_pll *pll); 22 23 u8 aty_ld_pll_ct(int offset, const struct atyfb_par *par) 24 { 25 26 /* write addr byte */ 27 aty_st_8(CLOCK_CNTL_ADDR, (offset << 2) & PLL_ADDR, par); 28 /* read the register value */ 29 return aty_ld_8(CLOCK_CNTL_DATA, par); 30 } 31 32 static void aty_st_pll_ct(int offset, u8 val, const struct atyfb_par *par) 33 { 34 /* write addr byte */ 35 aty_st_8(CLOCK_CNTL_ADDR, ((offset << 2) & PLL_ADDR) | PLL_WR_EN, par); 36 /* write the register value */ 37 aty_st_8(CLOCK_CNTL_DATA, val & PLL_DATA, par); 38 aty_st_8(CLOCK_CNTL_ADDR, ((offset << 2) & PLL_ADDR) & ~PLL_WR_EN, par); 39 } 40 41 /* 42 * by Daniel Mantione 43 * <daniel.mantione@freepascal.org> 44 * 45 * 46 * ATI Mach64 CT clock synthesis description. 47 * 48 * All clocks on the Mach64 can be calculated using the same principle: 49 * 50 * XTALIN * x * FB_DIV 51 * CLK = ---------------------- 52 * PLL_REF_DIV * POST_DIV 53 * 54 * XTALIN is a fixed speed clock. Common speeds are 14.31 MHz and 29.50 MHz. 55 * PLL_REF_DIV can be set by the user, but is the same for all clocks. 56 * FB_DIV can be set by the user for each clock individually, it should be set 57 * between 128 and 255, the chip will generate a bad clock signal for too low 58 * values. 59 * x depends on the type of clock; usually it is 2, but for the MCLK it can also 60 * be set to 4. 61 * POST_DIV can be set by the user for each clock individually, Possible values 62 * are 1,2,4,8 and for some clocks other values are available too. 63 * CLK is of course the clock speed that is generated. 64 * 65 * The Mach64 has these clocks: 66 * 67 * MCLK The clock rate of the chip 68 * XCLK The clock rate of the on-chip memory 69 * VCLK0 First pixel clock of first CRT controller 70 * VCLK1 Second pixel clock of first CRT controller 71 * VCLK2 Third pixel clock of first CRT controller 72 * VCLK3 Fourth pixel clock of first CRT controller 73 * VCLK Selected pixel clock, one of VCLK0, VCLK1, VCLK2, VCLK3 74 * V2CLK Pixel clock of the second CRT controller. 75 * SCLK Multi-purpose clock 76 * 77 * - MCLK and XCLK use the same FB_DIV 78 * - VCLK0 .. VCLK3 use the same FB_DIV 79 * - V2CLK is needed when the second CRTC is used (can be used for dualhead); 80 * i.e. CRT monitor connected to laptop has different resolution than built 81 * in LCD monitor. 82 * - SCLK is not available on all cards; it is know to exist on the Rage LT-PRO, 83 * Rage XL and Rage Mobility. It is know not to exist on the Mach64 VT. 84 * - V2CLK is not available on all cards, most likely only the Rage LT-PRO, 85 * the Rage XL and the Rage Mobility 86 * 87 * SCLK can be used to: 88 * - Clock the chip instead of MCLK 89 * - Replace XTALIN with a user defined frequency 90 * - Generate the pixel clock for the LCD monitor (instead of VCLK) 91 */ 92 93 /* 94 * It can be quite hard to calculate XCLK and MCLK if they don't run at the 95 * same frequency. Luckily, until now all cards that need asynchrone clock 96 * speeds seem to have SCLK. 97 * So this driver uses SCLK to clock the chip and XCLK to clock the memory. 98 */ 99 100 /* ------------------------------------------------------------------------- */ 101 102 /* 103 * PLL programming (Mach64 CT family) 104 * 105 * 106 * This procedure sets the display fifo. The display fifo is a buffer that 107 * contains data read from the video memory that waits to be processed by 108 * the CRT controller. 109 * 110 * On the more modern Mach64 variants, the chip doesn't calculate the 111 * interval after which the display fifo has to be reloaded from memory 112 * automatically, the driver has to do it instead. 113 */ 114 115 #define Maximum_DSP_PRECISION 7 116 const u8 aty_postdividers[8] = {1,2,4,8,3,5,6,12}; 117 118 static int aty_dsp_gt(const struct fb_info *info, u32 bpp, struct pll_ct *pll) 119 { 120 u32 dsp_off, dsp_on, dsp_xclks; 121 u32 multiplier, divider, ras_multiplier, ras_divider, tmp; 122 u8 vshift, xshift; 123 s8 dsp_precision; 124 125 multiplier = ((u32)pll->mclk_fb_div) * pll->vclk_post_div_real; 126 divider = ((u32)pll->vclk_fb_div) * pll->xclk_ref_div; 127 128 ras_multiplier = pll->xclkmaxrasdelay; 129 ras_divider = 1; 130 131 if (bpp>=8) 132 divider = divider * (bpp >> 2); 133 134 vshift = (6 - 2) - pll->xclk_post_div; /* FIFO is 64 bits wide in accelerator mode ... */ 135 136 if (bpp == 0) 137 vshift--; /* ... but only 32 bits in VGA mode. */ 138 139 #ifdef CONFIG_FB_ATY_GENERIC_LCD 140 if (pll->xres != 0) { 141 struct atyfb_par *par = (struct atyfb_par *) info->par; 142 143 multiplier = multiplier * par->lcd_width; 144 divider = divider * pll->xres & ~7; 145 146 ras_multiplier = ras_multiplier * par->lcd_width; 147 ras_divider = ras_divider * pll->xres & ~7; 148 } 149 #endif 150 /* If we don't do this, 32 bits for multiplier & divider won't be 151 enough in certain situations! */ 152 while (((multiplier | divider) & 1) == 0) { 153 multiplier = multiplier >> 1; 154 divider = divider >> 1; 155 } 156 157 /* Determine DSP precision first */ 158 tmp = ((multiplier * pll->fifo_size) << vshift) / divider; 159 160 for (dsp_precision = -5; tmp; dsp_precision++) 161 tmp >>= 1; 162 if (dsp_precision < 0) 163 dsp_precision = 0; 164 else if (dsp_precision > Maximum_DSP_PRECISION) 165 dsp_precision = Maximum_DSP_PRECISION; 166 167 xshift = 6 - dsp_precision; 168 vshift += xshift; 169 170 /* Move on to dsp_off */ 171 dsp_off = ((multiplier * (pll->fifo_size - 1)) << vshift) / divider - 172 (1 << (vshift - xshift)); 173 174 /* if (bpp == 0) 175 dsp_on = ((multiplier * 20 << vshift) + divider) / divider; 176 else */ 177 { 178 dsp_on = ((multiplier << vshift) + divider) / divider; 179 tmp = ((ras_multiplier << xshift) + ras_divider) / ras_divider; 180 if (dsp_on < tmp) 181 dsp_on = tmp; 182 dsp_on = dsp_on + (tmp * 2) + (pll->xclkpagefaultdelay << xshift); 183 } 184 185 /* Calculate rounding factor and apply it to dsp_on */ 186 tmp = ((1 << (Maximum_DSP_PRECISION - dsp_precision)) - 1) >> 1; 187 dsp_on = ((dsp_on + tmp) / (tmp + 1)) * (tmp + 1); 188 189 if (dsp_on >= ((dsp_off / (tmp + 1)) * (tmp + 1))) { 190 dsp_on = dsp_off - (multiplier << vshift) / divider; 191 dsp_on = (dsp_on / (tmp + 1)) * (tmp + 1); 192 } 193 194 /* Last but not least: dsp_xclks */ 195 dsp_xclks = ((multiplier << (vshift + 5)) + divider) / divider; 196 197 /* Get register values. */ 198 pll->dsp_on_off = (dsp_on << 16) + dsp_off; 199 pll->dsp_config = (dsp_precision << 20) | (pll->dsp_loop_latency << 16) | dsp_xclks; 200 #ifdef DEBUG 201 printk("atyfb(%s): dsp_config 0x%08x, dsp_on_off 0x%08x\n", 202 __func__, pll->dsp_config, pll->dsp_on_off); 203 #endif 204 return 0; 205 } 206 207 static int aty_valid_pll_ct(const struct fb_info *info, u32 vclk_per, struct pll_ct *pll) 208 { 209 u32 q; 210 struct atyfb_par *par = (struct atyfb_par *) info->par; 211 int pllvclk; 212 213 /* FIXME: use the VTB/GTB /{3,6,12} post dividers if they're better suited */ 214 q = par->ref_clk_per * pll->pll_ref_div * 4 / vclk_per; 215 if (q < 16*8 || q > 255*8) { 216 printk(KERN_CRIT "atyfb: vclk out of range\n"); 217 return -EINVAL; 218 } else { 219 pll->vclk_post_div = (q < 128*8); 220 pll->vclk_post_div += (q < 64*8); 221 pll->vclk_post_div += (q < 32*8); 222 } 223 pll->vclk_post_div_real = aty_postdividers[pll->vclk_post_div]; 224 // pll->vclk_post_div <<= 6; 225 pll->vclk_fb_div = q * pll->vclk_post_div_real / 8; 226 pllvclk = (1000000 * 2 * pll->vclk_fb_div) / 227 (par->ref_clk_per * pll->pll_ref_div); 228 #ifdef DEBUG 229 printk("atyfb(%s): pllvclk=%d MHz, vclk=%d MHz\n", 230 __func__, pllvclk, pllvclk / pll->vclk_post_div_real); 231 #endif 232 pll->pll_vclk_cntl = 0x03; /* VCLK = PLL_VCLK/VCLKx_POST */ 233 234 /* Set ECP (scaler/overlay clock) divider */ 235 if (par->pll_limits.ecp_max) { 236 int ecp = pllvclk / pll->vclk_post_div_real; 237 int ecp_div = 0; 238 239 while (ecp > par->pll_limits.ecp_max && ecp_div < 2) { 240 ecp >>= 1; 241 ecp_div++; 242 } 243 pll->pll_vclk_cntl |= ecp_div << 4; 244 } 245 246 return 0; 247 } 248 249 static int aty_var_to_pll_ct(const struct fb_info *info, u32 vclk_per, u32 bpp, union aty_pll *pll) 250 { 251 struct atyfb_par *par = (struct atyfb_par *) info->par; 252 int err; 253 254 if ((err = aty_valid_pll_ct(info, vclk_per, &pll->ct))) 255 return err; 256 if (M64_HAS(GTB_DSP) && (err = aty_dsp_gt(info, bpp, &pll->ct))) 257 return err; 258 /*aty_calc_pll_ct(info, &pll->ct);*/ 259 return 0; 260 } 261 262 static u32 aty_pll_to_var_ct(const struct fb_info *info, const union aty_pll *pll) 263 { 264 struct atyfb_par *par = (struct atyfb_par *) info->par; 265 u32 ret; 266 ret = par->ref_clk_per * pll->ct.pll_ref_div * pll->ct.vclk_post_div_real / pll->ct.vclk_fb_div / 2; 267 #ifdef CONFIG_FB_ATY_GENERIC_LCD 268 if(pll->ct.xres > 0) { 269 ret *= par->lcd_width; 270 ret /= pll->ct.xres; 271 } 272 #endif 273 #ifdef DEBUG 274 printk("atyfb(%s): calculated 0x%08X(%i)\n", __func__, ret, ret); 275 #endif 276 return ret; 277 } 278 279 void aty_set_pll_ct(const struct fb_info *info, const union aty_pll *pll) 280 { 281 struct atyfb_par *par = (struct atyfb_par *) info->par; 282 u32 crtc_gen_cntl; 283 u8 tmp, tmp2; 284 285 #ifdef CONFIG_FB_ATY_GENERIC_LCD 286 u32 lcd_gen_cntrl = 0; 287 #endif 288 289 #ifdef DEBUG 290 printk("atyfb(%s): about to program:\n" 291 "pll_ext_cntl=0x%02x pll_gen_cntl=0x%02x pll_vclk_cntl=0x%02x\n", 292 __func__, 293 pll->ct.pll_ext_cntl, pll->ct.pll_gen_cntl, pll->ct.pll_vclk_cntl); 294 295 printk("atyfb(%s): setting clock %lu for FeedBackDivider %i, ReferenceDivider %i, PostDivider %i(%i)\n", 296 __func__, 297 par->clk_wr_offset, pll->ct.vclk_fb_div, 298 pll->ct.pll_ref_div, pll->ct.vclk_post_div, pll->ct.vclk_post_div_real); 299 #endif 300 #ifdef CONFIG_FB_ATY_GENERIC_LCD 301 if (par->lcd_table != 0) { 302 /* turn off LCD */ 303 lcd_gen_cntrl = aty_ld_lcd(LCD_GEN_CNTL, par); 304 aty_st_lcd(LCD_GEN_CNTL, lcd_gen_cntrl & ~LCD_ON, par); 305 } 306 #endif 307 aty_st_8(CLOCK_CNTL, par->clk_wr_offset | CLOCK_STROBE, par); 308 309 /* Temporarily switch to accelerator mode */ 310 crtc_gen_cntl = aty_ld_le32(CRTC_GEN_CNTL, par); 311 if (!(crtc_gen_cntl & CRTC_EXT_DISP_EN)) 312 aty_st_le32(CRTC_GEN_CNTL, crtc_gen_cntl | CRTC_EXT_DISP_EN, par); 313 314 /* Reset VCLK generator */ 315 aty_st_pll_ct(PLL_VCLK_CNTL, pll->ct.pll_vclk_cntl, par); 316 317 /* Set post-divider */ 318 tmp2 = par->clk_wr_offset << 1; 319 tmp = aty_ld_pll_ct(VCLK_POST_DIV, par); 320 tmp &= ~(0x03U << tmp2); 321 tmp |= ((pll->ct.vclk_post_div & 0x03U) << tmp2); 322 aty_st_pll_ct(VCLK_POST_DIV, tmp, par); 323 324 /* Set extended post-divider */ 325 tmp = aty_ld_pll_ct(PLL_EXT_CNTL, par); 326 tmp &= ~(0x10U << par->clk_wr_offset); 327 tmp &= 0xF0U; 328 tmp |= pll->ct.pll_ext_cntl; 329 aty_st_pll_ct(PLL_EXT_CNTL, tmp, par); 330 331 /* Set feedback divider */ 332 tmp = VCLK0_FB_DIV + par->clk_wr_offset; 333 aty_st_pll_ct(tmp, (pll->ct.vclk_fb_div & 0xFFU), par); 334 335 aty_st_pll_ct(PLL_GEN_CNTL, (pll->ct.pll_gen_cntl & (~(PLL_OVERRIDE | PLL_MCLK_RST))) | OSC_EN, par); 336 337 /* End VCLK generator reset */ 338 aty_st_pll_ct(PLL_VCLK_CNTL, pll->ct.pll_vclk_cntl & ~(PLL_VCLK_RST), par); 339 mdelay(5); 340 341 aty_st_pll_ct(PLL_GEN_CNTL, pll->ct.pll_gen_cntl, par); 342 aty_st_pll_ct(PLL_VCLK_CNTL, pll->ct.pll_vclk_cntl, par); 343 mdelay(1); 344 345 /* Restore mode register */ 346 if (!(crtc_gen_cntl & CRTC_EXT_DISP_EN)) 347 aty_st_le32(CRTC_GEN_CNTL, crtc_gen_cntl, par); 348 349 if (M64_HAS(GTB_DSP)) { 350 u8 dll_cntl; 351 352 if (M64_HAS(XL_DLL)) 353 dll_cntl = 0x80; 354 else if (par->ram_type >= SDRAM) 355 dll_cntl = 0xa6; 356 else 357 dll_cntl = 0xa0; 358 aty_st_pll_ct(DLL_CNTL, dll_cntl, par); 359 aty_st_pll_ct(VFC_CNTL, 0x1b, par); 360 aty_st_le32(DSP_CONFIG, pll->ct.dsp_config, par); 361 aty_st_le32(DSP_ON_OFF, pll->ct.dsp_on_off, par); 362 363 mdelay(10); 364 aty_st_pll_ct(DLL_CNTL, dll_cntl, par); 365 mdelay(10); 366 aty_st_pll_ct(DLL_CNTL, dll_cntl | 0x40, par); 367 mdelay(10); 368 aty_st_pll_ct(DLL_CNTL, dll_cntl & ~0x40, par); 369 } 370 #ifdef CONFIG_FB_ATY_GENERIC_LCD 371 if (par->lcd_table != 0) { 372 /* restore LCD */ 373 aty_st_lcd(LCD_GEN_CNTL, lcd_gen_cntrl, par); 374 } 375 #endif 376 } 377 378 static void aty_get_pll_ct(const struct fb_info *info, union aty_pll *pll) 379 { 380 struct atyfb_par *par = (struct atyfb_par *) info->par; 381 u8 tmp, clock; 382 383 clock = aty_ld_8(CLOCK_CNTL, par) & 0x03U; 384 tmp = clock << 1; 385 pll->ct.vclk_post_div = (aty_ld_pll_ct(VCLK_POST_DIV, par) >> tmp) & 0x03U; 386 387 pll->ct.pll_ext_cntl = aty_ld_pll_ct(PLL_EXT_CNTL, par) & 0x0FU; 388 pll->ct.vclk_fb_div = aty_ld_pll_ct(VCLK0_FB_DIV + clock, par) & 0xFFU; 389 pll->ct.pll_ref_div = aty_ld_pll_ct(PLL_REF_DIV, par); 390 pll->ct.mclk_fb_div = aty_ld_pll_ct(MCLK_FB_DIV, par); 391 392 pll->ct.pll_gen_cntl = aty_ld_pll_ct(PLL_GEN_CNTL, par); 393 pll->ct.pll_vclk_cntl = aty_ld_pll_ct(PLL_VCLK_CNTL, par); 394 395 if (M64_HAS(GTB_DSP)) { 396 pll->ct.dsp_config = aty_ld_le32(DSP_CONFIG, par); 397 pll->ct.dsp_on_off = aty_ld_le32(DSP_ON_OFF, par); 398 } 399 } 400 401 static int aty_init_pll_ct(const struct fb_info *info, union aty_pll *pll) 402 { 403 struct atyfb_par *par = (struct atyfb_par *) info->par; 404 u8 mpost_div, xpost_div, sclk_post_div_real; 405 u32 q, memcntl, trp; 406 u32 dsp_config; 407 #ifdef DEBUG 408 int pllmclk, pllsclk; 409 #endif 410 pll->ct.pll_ext_cntl = aty_ld_pll_ct(PLL_EXT_CNTL, par); 411 pll->ct.xclk_post_div = pll->ct.pll_ext_cntl & 0x07; 412 pll->ct.xclk_ref_div = 1; 413 switch (pll->ct.xclk_post_div) { 414 case 0: case 1: case 2: case 3: 415 break; 416 417 case 4: 418 pll->ct.xclk_ref_div = 3; 419 pll->ct.xclk_post_div = 0; 420 break; 421 422 default: 423 printk(KERN_CRIT "atyfb: Unsupported xclk source: %d.\n", pll->ct.xclk_post_div); 424 return -EINVAL; 425 } 426 pll->ct.mclk_fb_mult = 2; 427 if(pll->ct.pll_ext_cntl & PLL_MFB_TIMES_4_2B) { 428 pll->ct.mclk_fb_mult = 4; 429 pll->ct.xclk_post_div -= 1; 430 } 431 432 #ifdef DEBUG 433 printk("atyfb(%s): mclk_fb_mult=%d, xclk_post_div=%d\n", 434 __func__, pll->ct.mclk_fb_mult, pll->ct.xclk_post_div); 435 #endif 436 437 memcntl = aty_ld_le32(MEM_CNTL, par); 438 trp = (memcntl & 0x300) >> 8; 439 440 pll->ct.xclkpagefaultdelay = ((memcntl & 0xc00) >> 10) + ((memcntl & 0x1000) >> 12) + trp + 2; 441 pll->ct.xclkmaxrasdelay = ((memcntl & 0x70000) >> 16) + trp + 2; 442 443 if (M64_HAS(FIFO_32)) { 444 pll->ct.fifo_size = 32; 445 } else { 446 pll->ct.fifo_size = 24; 447 pll->ct.xclkpagefaultdelay += 2; 448 pll->ct.xclkmaxrasdelay += 3; 449 } 450 451 switch (par->ram_type) { 452 case DRAM: 453 if (info->fix.smem_len<=ONE_MB) { 454 pll->ct.dsp_loop_latency = 10; 455 } else { 456 pll->ct.dsp_loop_latency = 8; 457 pll->ct.xclkpagefaultdelay += 2; 458 } 459 break; 460 case EDO: 461 case PSEUDO_EDO: 462 if (info->fix.smem_len<=ONE_MB) { 463 pll->ct.dsp_loop_latency = 9; 464 } else { 465 pll->ct.dsp_loop_latency = 8; 466 pll->ct.xclkpagefaultdelay += 1; 467 } 468 break; 469 case SDRAM: 470 if (info->fix.smem_len<=ONE_MB) { 471 pll->ct.dsp_loop_latency = 11; 472 } else { 473 pll->ct.dsp_loop_latency = 10; 474 pll->ct.xclkpagefaultdelay += 1; 475 } 476 break; 477 case SGRAM: 478 pll->ct.dsp_loop_latency = 8; 479 pll->ct.xclkpagefaultdelay += 3; 480 break; 481 default: 482 pll->ct.dsp_loop_latency = 11; 483 pll->ct.xclkpagefaultdelay += 3; 484 break; 485 } 486 487 if (pll->ct.xclkmaxrasdelay <= pll->ct.xclkpagefaultdelay) 488 pll->ct.xclkmaxrasdelay = pll->ct.xclkpagefaultdelay + 1; 489 490 /* Allow BIOS to override */ 491 dsp_config = aty_ld_le32(DSP_CONFIG, par); 492 aty_ld_le32(DSP_ON_OFF, par); 493 aty_ld_le32(VGA_DSP_CONFIG, par); 494 aty_ld_le32(VGA_DSP_ON_OFF, par); 495 496 if (dsp_config) 497 pll->ct.dsp_loop_latency = (dsp_config & DSP_LOOP_LATENCY) >> 16; 498 #if 0 499 FIXME: is it relevant for us? 500 if ((!dsp_on_off && !M64_HAS(RESET_3D)) || 501 ((dsp_on_off == vga_dsp_on_off) && 502 (!dsp_config || !((dsp_config ^ vga_dsp_config) & DSP_XCLKS_PER_QW)))) { 503 vga_dsp_on_off &= VGA_DSP_OFF; 504 vga_dsp_config &= VGA_DSP_XCLKS_PER_QW; 505 if (ATIDivide(vga_dsp_on_off, vga_dsp_config, 5, 1) > 24) 506 pll->ct.fifo_size = 32; 507 else 508 pll->ct.fifo_size = 24; 509 } 510 #endif 511 /* Exit if the user does not want us to tamper with the clock 512 rates of her chip. */ 513 if (par->mclk_per == 0) { 514 u8 mclk_fb_div, pll_ext_cntl; 515 pll->ct.pll_ref_div = aty_ld_pll_ct(PLL_REF_DIV, par); 516 pll_ext_cntl = aty_ld_pll_ct(PLL_EXT_CNTL, par); 517 pll->ct.xclk_post_div_real = aty_postdividers[pll_ext_cntl & 0x07]; 518 mclk_fb_div = aty_ld_pll_ct(MCLK_FB_DIV, par); 519 if (pll_ext_cntl & PLL_MFB_TIMES_4_2B) 520 mclk_fb_div <<= 1; 521 pll->ct.mclk_fb_div = mclk_fb_div; 522 return 0; 523 } 524 525 pll->ct.pll_ref_div = par->pll_per * 2 * 255 / par->ref_clk_per; 526 527 /* FIXME: use the VTB/GTB /3 post divider if it's better suited */ 528 q = par->ref_clk_per * pll->ct.pll_ref_div * 8 / 529 (pll->ct.mclk_fb_mult * par->xclk_per); 530 531 if (q < 16*8 || q > 255*8) { 532 printk(KERN_CRIT "atxfb: xclk out of range\n"); 533 return -EINVAL; 534 } else { 535 xpost_div = (q < 128*8); 536 xpost_div += (q < 64*8); 537 xpost_div += (q < 32*8); 538 } 539 pll->ct.xclk_post_div_real = aty_postdividers[xpost_div]; 540 pll->ct.mclk_fb_div = q * pll->ct.xclk_post_div_real / 8; 541 542 #ifdef CONFIG_PPC 543 if (machine_is(powermac)) { 544 /* Override PLL_EXT_CNTL & 0x07. */ 545 pll->ct.xclk_post_div = xpost_div; 546 pll->ct.xclk_ref_div = 1; 547 } 548 #endif 549 550 #ifdef DEBUG 551 pllmclk = (1000000 * pll->ct.mclk_fb_mult * pll->ct.mclk_fb_div) / 552 (par->ref_clk_per * pll->ct.pll_ref_div); 553 printk("atyfb(%s): pllmclk=%d MHz, xclk=%d MHz\n", 554 __func__, pllmclk, pllmclk / pll->ct.xclk_post_div_real); 555 #endif 556 557 if (M64_HAS(SDRAM_MAGIC_PLL) && (par->ram_type >= SDRAM)) 558 pll->ct.pll_gen_cntl = OSC_EN; 559 else 560 pll->ct.pll_gen_cntl = OSC_EN | DLL_PWDN /* | FORCE_DCLK_TRI_STATE */; 561 562 if (M64_HAS(MAGIC_POSTDIV)) 563 pll->ct.pll_ext_cntl = 0; 564 else 565 pll->ct.pll_ext_cntl = xpost_div; 566 567 if (pll->ct.mclk_fb_mult == 4) 568 pll->ct.pll_ext_cntl |= PLL_MFB_TIMES_4_2B; 569 570 if (par->mclk_per == par->xclk_per) { 571 pll->ct.pll_gen_cntl |= (xpost_div << 4); /* mclk == xclk */ 572 } else { 573 /* 574 * The chip clock is not equal to the memory clock. 575 * Therefore we will use sclk to clock the chip. 576 */ 577 pll->ct.pll_gen_cntl |= (6 << 4); /* mclk == sclk */ 578 579 q = par->ref_clk_per * pll->ct.pll_ref_div * 4 / par->mclk_per; 580 if (q < 16*8 || q > 255*8) { 581 printk(KERN_CRIT "atyfb: mclk out of range\n"); 582 return -EINVAL; 583 } else { 584 mpost_div = (q < 128*8); 585 mpost_div += (q < 64*8); 586 mpost_div += (q < 32*8); 587 } 588 sclk_post_div_real = aty_postdividers[mpost_div]; 589 pll->ct.sclk_fb_div = q * sclk_post_div_real / 8; 590 pll->ct.spll_cntl2 = mpost_div << 4; 591 #ifdef DEBUG 592 pllsclk = (1000000 * 2 * pll->ct.sclk_fb_div) / 593 (par->ref_clk_per * pll->ct.pll_ref_div); 594 printk("atyfb(%s): use sclk, pllsclk=%d MHz, sclk=mclk=%d MHz\n", 595 __func__, pllsclk, pllsclk / sclk_post_div_real); 596 #endif 597 } 598 599 /* Disable the extra precision pixel clock controls since we do not use them. */ 600 pll->ct.ext_vpll_cntl = aty_ld_pll_ct(EXT_VPLL_CNTL, par); 601 pll->ct.ext_vpll_cntl &= ~(EXT_VPLL_EN | EXT_VPLL_VGA_EN | EXT_VPLL_INSYNC); 602 603 return 0; 604 } 605 606 static void aty_resume_pll_ct(const struct fb_info *info, 607 union aty_pll *pll) 608 { 609 struct atyfb_par *par = info->par; 610 611 if (par->mclk_per != par->xclk_per) { 612 /* 613 * This disables the sclk, crashes the computer as reported: 614 * aty_st_pll_ct(SPLL_CNTL2, 3, info); 615 * 616 * So it seems the sclk must be enabled before it is used; 617 * so PLL_GEN_CNTL must be programmed *after* the sclk. 618 */ 619 aty_st_pll_ct(SCLK_FB_DIV, pll->ct.sclk_fb_div, par); 620 aty_st_pll_ct(SPLL_CNTL2, pll->ct.spll_cntl2, par); 621 /* 622 * SCLK has been started. Wait for the PLL to lock. 5 ms 623 * should be enough according to mach64 programmer's guide. 624 */ 625 mdelay(5); 626 } 627 628 aty_st_pll_ct(PLL_REF_DIV, pll->ct.pll_ref_div, par); 629 aty_st_pll_ct(PLL_GEN_CNTL, pll->ct.pll_gen_cntl, par); 630 aty_st_pll_ct(MCLK_FB_DIV, pll->ct.mclk_fb_div, par); 631 aty_st_pll_ct(PLL_EXT_CNTL, pll->ct.pll_ext_cntl, par); 632 aty_st_pll_ct(EXT_VPLL_CNTL, pll->ct.ext_vpll_cntl, par); 633 } 634 635 static int dummy(void) 636 { 637 return 0; 638 } 639 640 const struct aty_dac_ops aty_dac_ct = { 641 .set_dac = (void *) dummy, 642 }; 643 644 const struct aty_pll_ops aty_pll_ct = { 645 .var_to_pll = aty_var_to_pll_ct, 646 .pll_to_var = aty_pll_to_var_ct, 647 .set_pll = aty_set_pll_ct, 648 .get_pll = aty_get_pll_ct, 649 .init_pll = aty_init_pll_ct, 650 .resume_pll = aty_resume_pll_ct, 651 }; 652