1 /* 2 * USB ConnectTech WhiteHEAT driver 3 * 4 * Copyright (C) 2002 5 * Connect Tech Inc. 6 * 7 * Copyright (C) 1999 - 2001 8 * Greg Kroah-Hartman (greg@kroah.com) 9 * 10 * This program is free software; you can redistribute it and/or modify 11 * it under the terms of the GNU General Public License as published by 12 * the Free Software Foundation; either version 2 of the License, or 13 * (at your option) any later version. 14 * 15 * See Documentation/usb/usb-serial.txt for more information on using this 16 * driver 17 */ 18 19 #include <linux/kernel.h> 20 #include <linux/errno.h> 21 #include <linux/init.h> 22 #include <linux/slab.h> 23 #include <linux/tty.h> 24 #include <linux/tty_driver.h> 25 #include <linux/tty_flip.h> 26 #include <linux/module.h> 27 #include <linux/spinlock.h> 28 #include <linux/mutex.h> 29 #include <linux/uaccess.h> 30 #include <asm/termbits.h> 31 #include <linux/usb.h> 32 #include <linux/serial_reg.h> 33 #include <linux/serial.h> 34 #include <linux/usb/serial.h> 35 #include <linux/firmware.h> 36 #include <linux/ihex.h> 37 #include "whiteheat.h" /* WhiteHEAT specific commands */ 38 39 static bool debug; 40 41 #ifndef CMSPAR 42 #define CMSPAR 0 43 #endif 44 45 /* 46 * Version Information 47 */ 48 #define DRIVER_AUTHOR "Greg Kroah-Hartman <greg@kroah.com>, Stuart MacDonald <stuartm@connecttech.com>" 49 #define DRIVER_DESC "USB ConnectTech WhiteHEAT driver" 50 51 #define CONNECT_TECH_VENDOR_ID 0x0710 52 #define CONNECT_TECH_FAKE_WHITE_HEAT_ID 0x0001 53 #define CONNECT_TECH_WHITE_HEAT_ID 0x8001 54 55 /* 56 ID tables for whiteheat are unusual, because we want to different 57 things for different versions of the device. Eventually, this 58 will be doable from a single table. But, for now, we define two 59 separate ID tables, and then a third table that combines them 60 just for the purpose of exporting the autoloading information. 61 */ 62 static const struct usb_device_id id_table_std[] = { 63 { USB_DEVICE(CONNECT_TECH_VENDOR_ID, CONNECT_TECH_WHITE_HEAT_ID) }, 64 { } /* Terminating entry */ 65 }; 66 67 static const struct usb_device_id id_table_prerenumeration[] = { 68 { USB_DEVICE(CONNECT_TECH_VENDOR_ID, CONNECT_TECH_FAKE_WHITE_HEAT_ID) }, 69 { } /* Terminating entry */ 70 }; 71 72 static const struct usb_device_id id_table_combined[] = { 73 { USB_DEVICE(CONNECT_TECH_VENDOR_ID, CONNECT_TECH_WHITE_HEAT_ID) }, 74 { USB_DEVICE(CONNECT_TECH_VENDOR_ID, CONNECT_TECH_FAKE_WHITE_HEAT_ID) }, 75 { } /* Terminating entry */ 76 }; 77 78 MODULE_DEVICE_TABLE(usb, id_table_combined); 79 80 81 /* function prototypes for the Connect Tech WhiteHEAT prerenumeration device */ 82 static int whiteheat_firmware_download(struct usb_serial *serial, 83 const struct usb_device_id *id); 84 static int whiteheat_firmware_attach(struct usb_serial *serial); 85 86 /* function prototypes for the Connect Tech WhiteHEAT serial converter */ 87 static int whiteheat_attach(struct usb_serial *serial); 88 static void whiteheat_release(struct usb_serial *serial); 89 static int whiteheat_open(struct tty_struct *tty, 90 struct usb_serial_port *port); 91 static void whiteheat_close(struct usb_serial_port *port); 92 static int whiteheat_ioctl(struct tty_struct *tty, 93 unsigned int cmd, unsigned long arg); 94 static void whiteheat_set_termios(struct tty_struct *tty, 95 struct usb_serial_port *port, struct ktermios *old); 96 static int whiteheat_tiocmget(struct tty_struct *tty); 97 static int whiteheat_tiocmset(struct tty_struct *tty, 98 unsigned int set, unsigned int clear); 99 static void whiteheat_break_ctl(struct tty_struct *tty, int break_state); 100 101 static struct usb_serial_driver whiteheat_fake_device = { 102 .driver = { 103 .owner = THIS_MODULE, 104 .name = "whiteheatnofirm", 105 }, 106 .description = "Connect Tech - WhiteHEAT - (prerenumeration)", 107 .id_table = id_table_prerenumeration, 108 .num_ports = 1, 109 .probe = whiteheat_firmware_download, 110 .attach = whiteheat_firmware_attach, 111 }; 112 113 static struct usb_serial_driver whiteheat_device = { 114 .driver = { 115 .owner = THIS_MODULE, 116 .name = "whiteheat", 117 }, 118 .description = "Connect Tech - WhiteHEAT", 119 .id_table = id_table_std, 120 .num_ports = 4, 121 .attach = whiteheat_attach, 122 .release = whiteheat_release, 123 .open = whiteheat_open, 124 .close = whiteheat_close, 125 .ioctl = whiteheat_ioctl, 126 .set_termios = whiteheat_set_termios, 127 .break_ctl = whiteheat_break_ctl, 128 .tiocmget = whiteheat_tiocmget, 129 .tiocmset = whiteheat_tiocmset, 130 .throttle = usb_serial_generic_throttle, 131 .unthrottle = usb_serial_generic_unthrottle, 132 }; 133 134 static struct usb_serial_driver * const serial_drivers[] = { 135 &whiteheat_fake_device, &whiteheat_device, NULL 136 }; 137 138 struct whiteheat_command_private { 139 struct mutex mutex; 140 __u8 port_running; 141 __u8 command_finished; 142 wait_queue_head_t wait_command; /* for handling sleeping whilst 143 waiting for a command to 144 finish */ 145 __u8 result_buffer[64]; 146 }; 147 148 struct whiteheat_private { 149 __u8 mcr; /* FIXME: no locking on mcr */ 150 }; 151 152 153 /* local function prototypes */ 154 static int start_command_port(struct usb_serial *serial); 155 static void stop_command_port(struct usb_serial *serial); 156 static void command_port_write_callback(struct urb *urb); 157 static void command_port_read_callback(struct urb *urb); 158 159 static int firm_send_command(struct usb_serial_port *port, __u8 command, 160 __u8 *data, __u8 datasize); 161 static int firm_open(struct usb_serial_port *port); 162 static int firm_close(struct usb_serial_port *port); 163 static void firm_setup_port(struct tty_struct *tty); 164 static int firm_set_rts(struct usb_serial_port *port, __u8 onoff); 165 static int firm_set_dtr(struct usb_serial_port *port, __u8 onoff); 166 static int firm_set_break(struct usb_serial_port *port, __u8 onoff); 167 static int firm_purge(struct usb_serial_port *port, __u8 rxtx); 168 static int firm_get_dtr_rts(struct usb_serial_port *port); 169 static int firm_report_tx_done(struct usb_serial_port *port); 170 171 172 #define COMMAND_PORT 4 173 #define COMMAND_TIMEOUT (2*HZ) /* 2 second timeout for a command */ 174 #define COMMAND_TIMEOUT_MS 2000 175 #define CLOSING_DELAY (30 * HZ) 176 177 178 /***************************************************************************** 179 * Connect Tech's White Heat prerenumeration driver functions 180 *****************************************************************************/ 181 182 /* steps to download the firmware to the WhiteHEAT device: 183 - hold the reset (by writing to the reset bit of the CPUCS register) 184 - download the VEND_AX.HEX file to the chip using VENDOR_REQUEST-ANCHOR_LOAD 185 - release the reset (by writing to the CPUCS register) 186 - download the WH.HEX file for all addresses greater than 0x1b3f using 187 VENDOR_REQUEST-ANCHOR_EXTERNAL_RAM_LOAD 188 - hold the reset 189 - download the WH.HEX file for all addresses less than 0x1b40 using 190 VENDOR_REQUEST_ANCHOR_LOAD 191 - release the reset 192 - device renumerated itself and comes up as new device id with all 193 firmware download completed. 194 */ 195 static int whiteheat_firmware_download(struct usb_serial *serial, 196 const struct usb_device_id *id) 197 { 198 int response, ret = -ENOENT; 199 const struct firmware *loader_fw = NULL, *firmware_fw = NULL; 200 const struct ihex_binrec *record; 201 202 if (request_ihex_firmware(&firmware_fw, "whiteheat.fw", 203 &serial->dev->dev)) { 204 dev_err(&serial->dev->dev, 205 "%s - request \"whiteheat.fw\" failed\n", __func__); 206 goto out; 207 } 208 if (request_ihex_firmware(&loader_fw, "whiteheat_loader.fw", 209 &serial->dev->dev)) { 210 dev_err(&serial->dev->dev, 211 "%s - request \"whiteheat_loader.fw\" failed\n", 212 __func__); 213 goto out; 214 } 215 ret = 0; 216 response = ezusb_set_reset (serial, 1); 217 218 record = (const struct ihex_binrec *)loader_fw->data; 219 while (record) { 220 response = ezusb_writememory (serial, be32_to_cpu(record->addr), 221 (unsigned char *)record->data, 222 be16_to_cpu(record->len), 0xa0); 223 if (response < 0) { 224 dev_err(&serial->dev->dev, "%s - ezusb_writememory " 225 "failed for loader (%d %04X %p %d)\n", 226 __func__, response, be32_to_cpu(record->addr), 227 record->data, be16_to_cpu(record->len)); 228 break; 229 } 230 record = ihex_next_binrec(record); 231 } 232 233 response = ezusb_set_reset(serial, 0); 234 235 record = (const struct ihex_binrec *)firmware_fw->data; 236 while (record && be32_to_cpu(record->addr) < 0x1b40) 237 record = ihex_next_binrec(record); 238 while (record) { 239 response = ezusb_writememory (serial, be32_to_cpu(record->addr), 240 (unsigned char *)record->data, 241 be16_to_cpu(record->len), 0xa3); 242 if (response < 0) { 243 dev_err(&serial->dev->dev, "%s - ezusb_writememory " 244 "failed for first firmware step " 245 "(%d %04X %p %d)\n", __func__, response, 246 be32_to_cpu(record->addr), record->data, 247 be16_to_cpu(record->len)); 248 break; 249 } 250 ++record; 251 } 252 253 response = ezusb_set_reset(serial, 1); 254 255 record = (const struct ihex_binrec *)firmware_fw->data; 256 while (record && be32_to_cpu(record->addr) < 0x1b40) { 257 response = ezusb_writememory (serial, be32_to_cpu(record->addr), 258 (unsigned char *)record->data, 259 be16_to_cpu(record->len), 0xa0); 260 if (response < 0) { 261 dev_err(&serial->dev->dev, "%s - ezusb_writememory " 262 "failed for second firmware step " 263 "(%d %04X %p %d)\n", __func__, response, 264 be32_to_cpu(record->addr), record->data, 265 be16_to_cpu(record->len)); 266 break; 267 } 268 ++record; 269 } 270 ret = 0; 271 response = ezusb_set_reset (serial, 0); 272 out: 273 release_firmware(loader_fw); 274 release_firmware(firmware_fw); 275 return ret; 276 } 277 278 279 static int whiteheat_firmware_attach(struct usb_serial *serial) 280 { 281 /* We want this device to fail to have a driver assigned to it */ 282 return 1; 283 } 284 285 286 /***************************************************************************** 287 * Connect Tech's White Heat serial driver functions 288 *****************************************************************************/ 289 static int whiteheat_attach(struct usb_serial *serial) 290 { 291 struct usb_serial_port *command_port; 292 struct whiteheat_command_private *command_info; 293 struct usb_serial_port *port; 294 struct whiteheat_private *info; 295 struct whiteheat_hw_info *hw_info; 296 int pipe; 297 int ret; 298 int alen; 299 __u8 *command; 300 __u8 *result; 301 int i; 302 303 command_port = serial->port[COMMAND_PORT]; 304 305 pipe = usb_sndbulkpipe(serial->dev, 306 command_port->bulk_out_endpointAddress); 307 command = kmalloc(2, GFP_KERNEL); 308 if (!command) 309 goto no_command_buffer; 310 command[0] = WHITEHEAT_GET_HW_INFO; 311 command[1] = 0; 312 313 result = kmalloc(sizeof(*hw_info) + 1, GFP_KERNEL); 314 if (!result) 315 goto no_result_buffer; 316 /* 317 * When the module is reloaded the firmware is still there and 318 * the endpoints are still in the usb core unchanged. This is the 319 * unlinking bug in disguise. Same for the call below. 320 */ 321 usb_clear_halt(serial->dev, pipe); 322 ret = usb_bulk_msg(serial->dev, pipe, command, 2, 323 &alen, COMMAND_TIMEOUT_MS); 324 if (ret) { 325 dev_err(&serial->dev->dev, "%s: Couldn't send command [%d]\n", 326 serial->type->description, ret); 327 goto no_firmware; 328 } else if (alen != 2) { 329 dev_err(&serial->dev->dev, "%s: Send command incomplete [%d]\n", 330 serial->type->description, alen); 331 goto no_firmware; 332 } 333 334 pipe = usb_rcvbulkpipe(serial->dev, 335 command_port->bulk_in_endpointAddress); 336 /* See the comment on the usb_clear_halt() above */ 337 usb_clear_halt(serial->dev, pipe); 338 ret = usb_bulk_msg(serial->dev, pipe, result, 339 sizeof(*hw_info) + 1, &alen, COMMAND_TIMEOUT_MS); 340 if (ret) { 341 dev_err(&serial->dev->dev, "%s: Couldn't get results [%d]\n", 342 serial->type->description, ret); 343 goto no_firmware; 344 } else if (alen != sizeof(*hw_info) + 1) { 345 dev_err(&serial->dev->dev, "%s: Get results incomplete [%d]\n", 346 serial->type->description, alen); 347 goto no_firmware; 348 } else if (result[0] != command[0]) { 349 dev_err(&serial->dev->dev, "%s: Command failed [%d]\n", 350 serial->type->description, result[0]); 351 goto no_firmware; 352 } 353 354 hw_info = (struct whiteheat_hw_info *)&result[1]; 355 356 dev_info(&serial->dev->dev, "%s: Firmware v%d.%02d\n", 357 serial->type->description, 358 hw_info->sw_major_rev, hw_info->sw_minor_rev); 359 360 for (i = 0; i < serial->num_ports; i++) { 361 port = serial->port[i]; 362 363 info = kmalloc(sizeof(struct whiteheat_private), GFP_KERNEL); 364 if (info == NULL) { 365 dev_err(&port->dev, 366 "%s: Out of memory for port structures\n", 367 serial->type->description); 368 goto no_private; 369 } 370 371 info->mcr = 0; 372 373 usb_set_serial_port_data(port, info); 374 } 375 376 command_info = kmalloc(sizeof(struct whiteheat_command_private), 377 GFP_KERNEL); 378 if (command_info == NULL) { 379 dev_err(&serial->dev->dev, 380 "%s: Out of memory for port structures\n", 381 serial->type->description); 382 goto no_command_private; 383 } 384 385 mutex_init(&command_info->mutex); 386 command_info->port_running = 0; 387 init_waitqueue_head(&command_info->wait_command); 388 usb_set_serial_port_data(command_port, command_info); 389 command_port->write_urb->complete = command_port_write_callback; 390 command_port->read_urb->complete = command_port_read_callback; 391 kfree(result); 392 kfree(command); 393 394 return 0; 395 396 no_firmware: 397 /* Firmware likely not running */ 398 dev_err(&serial->dev->dev, 399 "%s: Unable to retrieve firmware version, try replugging\n", 400 serial->type->description); 401 dev_err(&serial->dev->dev, 402 "%s: If the firmware is not running (status led not blinking)\n", 403 serial->type->description); 404 dev_err(&serial->dev->dev, 405 "%s: please contact support@connecttech.com\n", 406 serial->type->description); 407 kfree(result); 408 return -ENODEV; 409 410 no_command_private: 411 for (i = serial->num_ports - 1; i >= 0; i--) { 412 port = serial->port[i]; 413 info = usb_get_serial_port_data(port); 414 kfree(info); 415 no_private: 416 ; 417 } 418 kfree(result); 419 no_result_buffer: 420 kfree(command); 421 no_command_buffer: 422 return -ENOMEM; 423 } 424 425 426 static void whiteheat_release(struct usb_serial *serial) 427 { 428 struct usb_serial_port *command_port; 429 struct whiteheat_private *info; 430 int i; 431 432 /* free up our private data for our command port */ 433 command_port = serial->port[COMMAND_PORT]; 434 kfree(usb_get_serial_port_data(command_port)); 435 436 for (i = 0; i < serial->num_ports; i++) { 437 info = usb_get_serial_port_data(serial->port[i]); 438 kfree(info); 439 } 440 } 441 442 static int whiteheat_open(struct tty_struct *tty, struct usb_serial_port *port) 443 { 444 int retval; 445 446 retval = start_command_port(port->serial); 447 if (retval) 448 goto exit; 449 450 /* send an open port command */ 451 retval = firm_open(port); 452 if (retval) { 453 stop_command_port(port->serial); 454 goto exit; 455 } 456 457 retval = firm_purge(port, WHITEHEAT_PURGE_RX | WHITEHEAT_PURGE_TX); 458 if (retval) { 459 firm_close(port); 460 stop_command_port(port->serial); 461 goto exit; 462 } 463 464 if (tty) 465 firm_setup_port(tty); 466 467 /* Work around HCD bugs */ 468 usb_clear_halt(port->serial->dev, port->read_urb->pipe); 469 usb_clear_halt(port->serial->dev, port->write_urb->pipe); 470 471 retval = usb_serial_generic_open(tty, port); 472 if (retval) { 473 firm_close(port); 474 stop_command_port(port->serial); 475 goto exit; 476 } 477 exit: 478 return retval; 479 } 480 481 482 static void whiteheat_close(struct usb_serial_port *port) 483 { 484 firm_report_tx_done(port); 485 firm_close(port); 486 487 usb_serial_generic_close(port); 488 489 stop_command_port(port->serial); 490 } 491 492 static int whiteheat_tiocmget(struct tty_struct *tty) 493 { 494 struct usb_serial_port *port = tty->driver_data; 495 struct whiteheat_private *info = usb_get_serial_port_data(port); 496 unsigned int modem_signals = 0; 497 498 firm_get_dtr_rts(port); 499 if (info->mcr & UART_MCR_DTR) 500 modem_signals |= TIOCM_DTR; 501 if (info->mcr & UART_MCR_RTS) 502 modem_signals |= TIOCM_RTS; 503 504 return modem_signals; 505 } 506 507 static int whiteheat_tiocmset(struct tty_struct *tty, 508 unsigned int set, unsigned int clear) 509 { 510 struct usb_serial_port *port = tty->driver_data; 511 struct whiteheat_private *info = usb_get_serial_port_data(port); 512 513 if (set & TIOCM_RTS) 514 info->mcr |= UART_MCR_RTS; 515 if (set & TIOCM_DTR) 516 info->mcr |= UART_MCR_DTR; 517 518 if (clear & TIOCM_RTS) 519 info->mcr &= ~UART_MCR_RTS; 520 if (clear & TIOCM_DTR) 521 info->mcr &= ~UART_MCR_DTR; 522 523 firm_set_dtr(port, info->mcr & UART_MCR_DTR); 524 firm_set_rts(port, info->mcr & UART_MCR_RTS); 525 return 0; 526 } 527 528 529 static int whiteheat_ioctl(struct tty_struct *tty, 530 unsigned int cmd, unsigned long arg) 531 { 532 struct usb_serial_port *port = tty->driver_data; 533 struct serial_struct serstruct; 534 void __user *user_arg = (void __user *)arg; 535 536 dbg("%s - port %d, cmd 0x%.4x", __func__, port->number, cmd); 537 538 switch (cmd) { 539 case TIOCGSERIAL: 540 memset(&serstruct, 0, sizeof(serstruct)); 541 serstruct.type = PORT_16654; 542 serstruct.line = port->serial->minor; 543 serstruct.port = port->number; 544 serstruct.flags = ASYNC_SKIP_TEST | ASYNC_AUTO_IRQ; 545 serstruct.xmit_fifo_size = kfifo_size(&port->write_fifo); 546 serstruct.custom_divisor = 0; 547 serstruct.baud_base = 460800; 548 serstruct.close_delay = CLOSING_DELAY; 549 serstruct.closing_wait = CLOSING_DELAY; 550 551 if (copy_to_user(user_arg, &serstruct, sizeof(serstruct))) 552 return -EFAULT; 553 break; 554 default: 555 break; 556 } 557 558 return -ENOIOCTLCMD; 559 } 560 561 562 static void whiteheat_set_termios(struct tty_struct *tty, 563 struct usb_serial_port *port, struct ktermios *old_termios) 564 { 565 firm_setup_port(tty); 566 } 567 568 static void whiteheat_break_ctl(struct tty_struct *tty, int break_state) 569 { 570 struct usb_serial_port *port = tty->driver_data; 571 firm_set_break(port, break_state); 572 } 573 574 575 /***************************************************************************** 576 * Connect Tech's White Heat callback routines 577 *****************************************************************************/ 578 static void command_port_write_callback(struct urb *urb) 579 { 580 int status = urb->status; 581 582 if (status) { 583 dbg("nonzero urb status: %d", status); 584 return; 585 } 586 } 587 588 589 static void command_port_read_callback(struct urb *urb) 590 { 591 struct usb_serial_port *command_port = urb->context; 592 struct whiteheat_command_private *command_info; 593 int status = urb->status; 594 unsigned char *data = urb->transfer_buffer; 595 int result; 596 597 command_info = usb_get_serial_port_data(command_port); 598 if (!command_info) { 599 dbg("%s - command_info is NULL, exiting.", __func__); 600 return; 601 } 602 if (status) { 603 dbg("%s - nonzero urb status: %d", __func__, status); 604 if (status != -ENOENT) 605 command_info->command_finished = WHITEHEAT_CMD_FAILURE; 606 wake_up(&command_info->wait_command); 607 return; 608 } 609 610 usb_serial_debug_data(debug, &command_port->dev, 611 __func__, urb->actual_length, data); 612 613 if (data[0] == WHITEHEAT_CMD_COMPLETE) { 614 command_info->command_finished = WHITEHEAT_CMD_COMPLETE; 615 wake_up(&command_info->wait_command); 616 } else if (data[0] == WHITEHEAT_CMD_FAILURE) { 617 command_info->command_finished = WHITEHEAT_CMD_FAILURE; 618 wake_up(&command_info->wait_command); 619 } else if (data[0] == WHITEHEAT_EVENT) { 620 /* These are unsolicited reports from the firmware, hence no 621 waiting command to wakeup */ 622 dbg("%s - event received", __func__); 623 } else if (data[0] == WHITEHEAT_GET_DTR_RTS) { 624 memcpy(command_info->result_buffer, &data[1], 625 urb->actual_length - 1); 626 command_info->command_finished = WHITEHEAT_CMD_COMPLETE; 627 wake_up(&command_info->wait_command); 628 } else 629 dbg("%s - bad reply from firmware", __func__); 630 631 /* Continue trying to always read */ 632 result = usb_submit_urb(command_port->read_urb, GFP_ATOMIC); 633 if (result) 634 dbg("%s - failed resubmitting read urb, error %d", 635 __func__, result); 636 } 637 638 639 /***************************************************************************** 640 * Connect Tech's White Heat firmware interface 641 *****************************************************************************/ 642 static int firm_send_command(struct usb_serial_port *port, __u8 command, 643 __u8 *data, __u8 datasize) 644 { 645 struct usb_serial_port *command_port; 646 struct whiteheat_command_private *command_info; 647 struct whiteheat_private *info; 648 __u8 *transfer_buffer; 649 int retval = 0; 650 int t; 651 652 dbg("%s - command %d", __func__, command); 653 654 command_port = port->serial->port[COMMAND_PORT]; 655 command_info = usb_get_serial_port_data(command_port); 656 mutex_lock(&command_info->mutex); 657 command_info->command_finished = false; 658 659 transfer_buffer = (__u8 *)command_port->write_urb->transfer_buffer; 660 transfer_buffer[0] = command; 661 memcpy(&transfer_buffer[1], data, datasize); 662 command_port->write_urb->transfer_buffer_length = datasize + 1; 663 retval = usb_submit_urb(command_port->write_urb, GFP_NOIO); 664 if (retval) { 665 dbg("%s - submit urb failed", __func__); 666 goto exit; 667 } 668 669 /* wait for the command to complete */ 670 t = wait_event_timeout(command_info->wait_command, 671 (bool)command_info->command_finished, COMMAND_TIMEOUT); 672 if (!t) 673 usb_kill_urb(command_port->write_urb); 674 675 if (command_info->command_finished == false) { 676 dbg("%s - command timed out.", __func__); 677 retval = -ETIMEDOUT; 678 goto exit; 679 } 680 681 if (command_info->command_finished == WHITEHEAT_CMD_FAILURE) { 682 dbg("%s - command failed.", __func__); 683 retval = -EIO; 684 goto exit; 685 } 686 687 if (command_info->command_finished == WHITEHEAT_CMD_COMPLETE) { 688 dbg("%s - command completed.", __func__); 689 switch (command) { 690 case WHITEHEAT_GET_DTR_RTS: 691 info = usb_get_serial_port_data(port); 692 memcpy(&info->mcr, command_info->result_buffer, 693 sizeof(struct whiteheat_dr_info)); 694 break; 695 } 696 } 697 exit: 698 mutex_unlock(&command_info->mutex); 699 return retval; 700 } 701 702 703 static int firm_open(struct usb_serial_port *port) 704 { 705 struct whiteheat_simple open_command; 706 707 open_command.port = port->number - port->serial->minor + 1; 708 return firm_send_command(port, WHITEHEAT_OPEN, 709 (__u8 *)&open_command, sizeof(open_command)); 710 } 711 712 713 static int firm_close(struct usb_serial_port *port) 714 { 715 struct whiteheat_simple close_command; 716 717 close_command.port = port->number - port->serial->minor + 1; 718 return firm_send_command(port, WHITEHEAT_CLOSE, 719 (__u8 *)&close_command, sizeof(close_command)); 720 } 721 722 723 static void firm_setup_port(struct tty_struct *tty) 724 { 725 struct usb_serial_port *port = tty->driver_data; 726 struct whiteheat_port_settings port_settings; 727 unsigned int cflag = tty->termios->c_cflag; 728 729 port_settings.port = port->number + 1; 730 731 /* get the byte size */ 732 switch (cflag & CSIZE) { 733 case CS5: port_settings.bits = 5; break; 734 case CS6: port_settings.bits = 6; break; 735 case CS7: port_settings.bits = 7; break; 736 default: 737 case CS8: port_settings.bits = 8; break; 738 } 739 dbg("%s - data bits = %d", __func__, port_settings.bits); 740 741 /* determine the parity */ 742 if (cflag & PARENB) 743 if (cflag & CMSPAR) 744 if (cflag & PARODD) 745 port_settings.parity = WHITEHEAT_PAR_MARK; 746 else 747 port_settings.parity = WHITEHEAT_PAR_SPACE; 748 else 749 if (cflag & PARODD) 750 port_settings.parity = WHITEHEAT_PAR_ODD; 751 else 752 port_settings.parity = WHITEHEAT_PAR_EVEN; 753 else 754 port_settings.parity = WHITEHEAT_PAR_NONE; 755 dbg("%s - parity = %c", __func__, port_settings.parity); 756 757 /* figure out the stop bits requested */ 758 if (cflag & CSTOPB) 759 port_settings.stop = 2; 760 else 761 port_settings.stop = 1; 762 dbg("%s - stop bits = %d", __func__, port_settings.stop); 763 764 /* figure out the flow control settings */ 765 if (cflag & CRTSCTS) 766 port_settings.hflow = (WHITEHEAT_HFLOW_CTS | 767 WHITEHEAT_HFLOW_RTS); 768 else 769 port_settings.hflow = WHITEHEAT_HFLOW_NONE; 770 dbg("%s - hardware flow control = %s %s %s %s", __func__, 771 (port_settings.hflow & WHITEHEAT_HFLOW_CTS) ? "CTS" : "", 772 (port_settings.hflow & WHITEHEAT_HFLOW_RTS) ? "RTS" : "", 773 (port_settings.hflow & WHITEHEAT_HFLOW_DSR) ? "DSR" : "", 774 (port_settings.hflow & WHITEHEAT_HFLOW_DTR) ? "DTR" : ""); 775 776 /* determine software flow control */ 777 if (I_IXOFF(tty)) 778 port_settings.sflow = WHITEHEAT_SFLOW_RXTX; 779 else 780 port_settings.sflow = WHITEHEAT_SFLOW_NONE; 781 dbg("%s - software flow control = %c", __func__, port_settings.sflow); 782 783 port_settings.xon = START_CHAR(tty); 784 port_settings.xoff = STOP_CHAR(tty); 785 dbg("%s - XON = %2x, XOFF = %2x", 786 __func__, port_settings.xon, port_settings.xoff); 787 788 /* get the baud rate wanted */ 789 port_settings.baud = tty_get_baud_rate(tty); 790 dbg("%s - baud rate = %d", __func__, port_settings.baud); 791 792 /* fixme: should set validated settings */ 793 tty_encode_baud_rate(tty, port_settings.baud, port_settings.baud); 794 /* handle any settings that aren't specified in the tty structure */ 795 port_settings.lloop = 0; 796 797 /* now send the message to the device */ 798 firm_send_command(port, WHITEHEAT_SETUP_PORT, 799 (__u8 *)&port_settings, sizeof(port_settings)); 800 } 801 802 803 static int firm_set_rts(struct usb_serial_port *port, __u8 onoff) 804 { 805 struct whiteheat_set_rdb rts_command; 806 807 rts_command.port = port->number - port->serial->minor + 1; 808 rts_command.state = onoff; 809 return firm_send_command(port, WHITEHEAT_SET_RTS, 810 (__u8 *)&rts_command, sizeof(rts_command)); 811 } 812 813 814 static int firm_set_dtr(struct usb_serial_port *port, __u8 onoff) 815 { 816 struct whiteheat_set_rdb dtr_command; 817 818 dtr_command.port = port->number - port->serial->minor + 1; 819 dtr_command.state = onoff; 820 return firm_send_command(port, WHITEHEAT_SET_DTR, 821 (__u8 *)&dtr_command, sizeof(dtr_command)); 822 } 823 824 825 static int firm_set_break(struct usb_serial_port *port, __u8 onoff) 826 { 827 struct whiteheat_set_rdb break_command; 828 829 break_command.port = port->number - port->serial->minor + 1; 830 break_command.state = onoff; 831 return firm_send_command(port, WHITEHEAT_SET_BREAK, 832 (__u8 *)&break_command, sizeof(break_command)); 833 } 834 835 836 static int firm_purge(struct usb_serial_port *port, __u8 rxtx) 837 { 838 struct whiteheat_purge purge_command; 839 840 purge_command.port = port->number - port->serial->minor + 1; 841 purge_command.what = rxtx; 842 return firm_send_command(port, WHITEHEAT_PURGE, 843 (__u8 *)&purge_command, sizeof(purge_command)); 844 } 845 846 847 static int firm_get_dtr_rts(struct usb_serial_port *port) 848 { 849 struct whiteheat_simple get_dr_command; 850 851 get_dr_command.port = port->number - port->serial->minor + 1; 852 return firm_send_command(port, WHITEHEAT_GET_DTR_RTS, 853 (__u8 *)&get_dr_command, sizeof(get_dr_command)); 854 } 855 856 857 static int firm_report_tx_done(struct usb_serial_port *port) 858 { 859 struct whiteheat_simple close_command; 860 861 close_command.port = port->number - port->serial->minor + 1; 862 return firm_send_command(port, WHITEHEAT_REPORT_TX_DONE, 863 (__u8 *)&close_command, sizeof(close_command)); 864 } 865 866 867 /***************************************************************************** 868 * Connect Tech's White Heat utility functions 869 *****************************************************************************/ 870 static int start_command_port(struct usb_serial *serial) 871 { 872 struct usb_serial_port *command_port; 873 struct whiteheat_command_private *command_info; 874 int retval = 0; 875 876 command_port = serial->port[COMMAND_PORT]; 877 command_info = usb_get_serial_port_data(command_port); 878 mutex_lock(&command_info->mutex); 879 if (!command_info->port_running) { 880 /* Work around HCD bugs */ 881 usb_clear_halt(serial->dev, command_port->read_urb->pipe); 882 883 retval = usb_submit_urb(command_port->read_urb, GFP_KERNEL); 884 if (retval) { 885 dev_err(&serial->dev->dev, 886 "%s - failed submitting read urb, error %d\n", 887 __func__, retval); 888 goto exit; 889 } 890 } 891 command_info->port_running++; 892 893 exit: 894 mutex_unlock(&command_info->mutex); 895 return retval; 896 } 897 898 899 static void stop_command_port(struct usb_serial *serial) 900 { 901 struct usb_serial_port *command_port; 902 struct whiteheat_command_private *command_info; 903 904 command_port = serial->port[COMMAND_PORT]; 905 command_info = usb_get_serial_port_data(command_port); 906 mutex_lock(&command_info->mutex); 907 command_info->port_running--; 908 if (!command_info->port_running) 909 usb_kill_urb(command_port->read_urb); 910 mutex_unlock(&command_info->mutex); 911 } 912 913 module_usb_serial_driver(serial_drivers, id_table_combined); 914 915 MODULE_AUTHOR(DRIVER_AUTHOR); 916 MODULE_DESCRIPTION(DRIVER_DESC); 917 MODULE_LICENSE("GPL"); 918 919 MODULE_FIRMWARE("whiteheat.fw"); 920 MODULE_FIRMWARE("whiteheat_loader.fw"); 921 922 module_param(debug, bool, S_IRUGO | S_IWUSR); 923 MODULE_PARM_DESC(debug, "Debug enabled or not"); 924