1 // SPDX-License-Identifier: GPL-2.0+ 2 /* 3 * mxuport.c - MOXA UPort series driver 4 * 5 * Copyright (c) 2006 Moxa Technologies Co., Ltd. 6 * Copyright (c) 2013 Andrew Lunn <andrew@lunn.ch> 7 * 8 * Supports the following Moxa USB to serial converters: 9 * 2 ports : UPort 1250, UPort 1250I 10 * 4 ports : UPort 1410, UPort 1450, UPort 1450I 11 * 8 ports : UPort 1610-8, UPort 1650-8 12 * 16 ports : UPort 1610-16, UPort 1650-16 13 */ 14 15 #include <linux/kernel.h> 16 #include <linux/module.h> 17 #include <linux/firmware.h> 18 #include <linux/jiffies.h> 19 #include <linux/serial.h> 20 #include <linux/serial_reg.h> 21 #include <linux/slab.h> 22 #include <linux/tty.h> 23 #include <linux/tty_driver.h> 24 #include <linux/tty_flip.h> 25 #include <linux/uaccess.h> 26 #include <linux/usb.h> 27 #include <linux/usb/serial.h> 28 #include <asm/unaligned.h> 29 30 /* Definitions for the vendor ID and device ID */ 31 #define MX_USBSERIAL_VID 0x110A 32 #define MX_UPORT1250_PID 0x1250 33 #define MX_UPORT1251_PID 0x1251 34 #define MX_UPORT1410_PID 0x1410 35 #define MX_UPORT1450_PID 0x1450 36 #define MX_UPORT1451_PID 0x1451 37 #define MX_UPORT1618_PID 0x1618 38 #define MX_UPORT1658_PID 0x1658 39 #define MX_UPORT1613_PID 0x1613 40 #define MX_UPORT1653_PID 0x1653 41 42 /* Definitions for USB info */ 43 #define HEADER_SIZE 4 44 #define EVENT_LENGTH 8 45 #define DOWN_BLOCK_SIZE 64 46 47 /* Definitions for firmware info */ 48 #define VER_ADDR_1 0x20 49 #define VER_ADDR_2 0x24 50 #define VER_ADDR_3 0x28 51 52 /* Definitions for USB vendor request */ 53 #define RQ_VENDOR_NONE 0x00 54 #define RQ_VENDOR_SET_BAUD 0x01 /* Set baud rate */ 55 #define RQ_VENDOR_SET_LINE 0x02 /* Set line status */ 56 #define RQ_VENDOR_SET_CHARS 0x03 /* Set Xon/Xoff chars */ 57 #define RQ_VENDOR_SET_RTS 0x04 /* Set RTS */ 58 #define RQ_VENDOR_SET_DTR 0x05 /* Set DTR */ 59 #define RQ_VENDOR_SET_XONXOFF 0x06 /* Set auto Xon/Xoff */ 60 #define RQ_VENDOR_SET_RX_HOST_EN 0x07 /* Set RX host enable */ 61 #define RQ_VENDOR_SET_OPEN 0x08 /* Set open/close port */ 62 #define RQ_VENDOR_PURGE 0x09 /* Purge Rx/Tx buffer */ 63 #define RQ_VENDOR_SET_MCR 0x0A /* Set MCR register */ 64 #define RQ_VENDOR_SET_BREAK 0x0B /* Set Break signal */ 65 66 #define RQ_VENDOR_START_FW_DOWN 0x0C /* Start firmware download */ 67 #define RQ_VENDOR_STOP_FW_DOWN 0x0D /* Stop firmware download */ 68 #define RQ_VENDOR_QUERY_FW_READY 0x0E /* Query if new firmware ready */ 69 70 #define RQ_VENDOR_SET_FIFO_DISABLE 0x0F /* Set fifo disable */ 71 #define RQ_VENDOR_SET_INTERFACE 0x10 /* Set interface */ 72 #define RQ_VENDOR_SET_HIGH_PERFOR 0x11 /* Set hi-performance */ 73 74 #define RQ_VENDOR_ERASE_BLOCK 0x12 /* Erase flash block */ 75 #define RQ_VENDOR_WRITE_PAGE 0x13 /* Write flash page */ 76 #define RQ_VENDOR_PREPARE_WRITE 0x14 /* Prepare write flash */ 77 #define RQ_VENDOR_CONFIRM_WRITE 0x15 /* Confirm write flash */ 78 #define RQ_VENDOR_LOCATE 0x16 /* Locate the device */ 79 80 #define RQ_VENDOR_START_ROM_DOWN 0x17 /* Start firmware download */ 81 #define RQ_VENDOR_ROM_DATA 0x18 /* Rom file data */ 82 #define RQ_VENDOR_STOP_ROM_DOWN 0x19 /* Stop firmware download */ 83 #define RQ_VENDOR_FW_DATA 0x20 /* Firmware data */ 84 85 #define RQ_VENDOR_RESET_DEVICE 0x23 /* Try to reset the device */ 86 #define RQ_VENDOR_QUERY_FW_CONFIG 0x24 87 88 #define RQ_VENDOR_GET_VERSION 0x81 /* Get firmware version */ 89 #define RQ_VENDOR_GET_PAGE 0x82 /* Read flash page */ 90 #define RQ_VENDOR_GET_ROM_PROC 0x83 /* Get ROM process state */ 91 92 #define RQ_VENDOR_GET_INQUEUE 0x84 /* Data in input buffer */ 93 #define RQ_VENDOR_GET_OUTQUEUE 0x85 /* Data in output buffer */ 94 95 #define RQ_VENDOR_GET_MSR 0x86 /* Get modem status register */ 96 97 /* Definitions for UPort event type */ 98 #define UPORT_EVENT_NONE 0 /* None */ 99 #define UPORT_EVENT_TXBUF_THRESHOLD 1 /* Tx buffer threshold */ 100 #define UPORT_EVENT_SEND_NEXT 2 /* Send next */ 101 #define UPORT_EVENT_MSR 3 /* Modem status */ 102 #define UPORT_EVENT_LSR 4 /* Line status */ 103 #define UPORT_EVENT_MCR 5 /* Modem control */ 104 105 /* Definitions for serial event type */ 106 #define SERIAL_EV_CTS 0x0008 /* CTS changed state */ 107 #define SERIAL_EV_DSR 0x0010 /* DSR changed state */ 108 #define SERIAL_EV_RLSD 0x0020 /* RLSD changed state */ 109 110 /* Definitions for modem control event type */ 111 #define SERIAL_EV_XOFF 0x40 /* XOFF received */ 112 113 /* Definitions for line control of communication */ 114 #define MX_WORDLENGTH_5 5 115 #define MX_WORDLENGTH_6 6 116 #define MX_WORDLENGTH_7 7 117 #define MX_WORDLENGTH_8 8 118 119 #define MX_PARITY_NONE 0 120 #define MX_PARITY_ODD 1 121 #define MX_PARITY_EVEN 2 122 #define MX_PARITY_MARK 3 123 #define MX_PARITY_SPACE 4 124 125 #define MX_STOP_BITS_1 0 126 #define MX_STOP_BITS_1_5 1 127 #define MX_STOP_BITS_2 2 128 129 #define MX_RTS_DISABLE 0x0 130 #define MX_RTS_ENABLE 0x1 131 #define MX_RTS_HW 0x2 132 #define MX_RTS_NO_CHANGE 0x3 /* Flag, not valid register value*/ 133 134 #define MX_INT_RS232 0 135 #define MX_INT_2W_RS485 1 136 #define MX_INT_RS422 2 137 #define MX_INT_4W_RS485 3 138 139 /* Definitions for holding reason */ 140 #define MX_WAIT_FOR_CTS 0x0001 141 #define MX_WAIT_FOR_DSR 0x0002 142 #define MX_WAIT_FOR_DCD 0x0004 143 #define MX_WAIT_FOR_XON 0x0008 144 #define MX_WAIT_FOR_START_TX 0x0010 145 #define MX_WAIT_FOR_UNTHROTTLE 0x0020 146 #define MX_WAIT_FOR_LOW_WATER 0x0040 147 #define MX_WAIT_FOR_SEND_NEXT 0x0080 148 149 #define MX_UPORT_2_PORT BIT(0) 150 #define MX_UPORT_4_PORT BIT(1) 151 #define MX_UPORT_8_PORT BIT(2) 152 #define MX_UPORT_16_PORT BIT(3) 153 154 /* This structure holds all of the local port information */ 155 struct mxuport_port { 156 u8 mcr_state; /* Last MCR state */ 157 u8 msr_state; /* Last MSR state */ 158 struct mutex mutex; /* Protects mcr_state */ 159 spinlock_t spinlock; /* Protects msr_state */ 160 }; 161 162 /* Table of devices that work with this driver */ 163 static const struct usb_device_id mxuport_idtable[] = { 164 { USB_DEVICE(MX_USBSERIAL_VID, MX_UPORT1250_PID), 165 .driver_info = MX_UPORT_2_PORT }, 166 { USB_DEVICE(MX_USBSERIAL_VID, MX_UPORT1251_PID), 167 .driver_info = MX_UPORT_2_PORT }, 168 { USB_DEVICE(MX_USBSERIAL_VID, MX_UPORT1410_PID), 169 .driver_info = MX_UPORT_4_PORT }, 170 { USB_DEVICE(MX_USBSERIAL_VID, MX_UPORT1450_PID), 171 .driver_info = MX_UPORT_4_PORT }, 172 { USB_DEVICE(MX_USBSERIAL_VID, MX_UPORT1451_PID), 173 .driver_info = MX_UPORT_4_PORT }, 174 { USB_DEVICE(MX_USBSERIAL_VID, MX_UPORT1618_PID), 175 .driver_info = MX_UPORT_8_PORT }, 176 { USB_DEVICE(MX_USBSERIAL_VID, MX_UPORT1658_PID), 177 .driver_info = MX_UPORT_8_PORT }, 178 { USB_DEVICE(MX_USBSERIAL_VID, MX_UPORT1613_PID), 179 .driver_info = MX_UPORT_16_PORT }, 180 { USB_DEVICE(MX_USBSERIAL_VID, MX_UPORT1653_PID), 181 .driver_info = MX_UPORT_16_PORT }, 182 {} /* Terminating entry */ 183 }; 184 185 MODULE_DEVICE_TABLE(usb, mxuport_idtable); 186 187 /* 188 * Add a four byte header containing the port number and the number of 189 * bytes of data in the message. Return the number of bytes in the 190 * buffer. 191 */ 192 static int mxuport_prepare_write_buffer(struct usb_serial_port *port, 193 void *dest, size_t size) 194 { 195 u8 *buf = dest; 196 int count; 197 198 count = kfifo_out_locked(&port->write_fifo, buf + HEADER_SIZE, 199 size - HEADER_SIZE, 200 &port->lock); 201 202 put_unaligned_be16(port->port_number, buf); 203 put_unaligned_be16(count, buf + 2); 204 205 dev_dbg(&port->dev, "%s - size %zd count %d\n", __func__, 206 size, count); 207 208 return count + HEADER_SIZE; 209 } 210 211 /* Read the given buffer in from the control pipe. */ 212 static int mxuport_recv_ctrl_urb(struct usb_serial *serial, 213 u8 request, u16 value, u16 index, 214 u8 *data, size_t size) 215 { 216 int status; 217 218 status = usb_control_msg(serial->dev, 219 usb_rcvctrlpipe(serial->dev, 0), 220 request, 221 (USB_DIR_IN | USB_TYPE_VENDOR | 222 USB_RECIP_DEVICE), value, index, 223 data, size, 224 USB_CTRL_GET_TIMEOUT); 225 if (status < 0) { 226 dev_err(&serial->interface->dev, 227 "%s - usb_control_msg failed (%d)\n", 228 __func__, status); 229 return status; 230 } 231 232 if (status != size) { 233 dev_err(&serial->interface->dev, 234 "%s - short read (%d / %zd)\n", 235 __func__, status, size); 236 return -EIO; 237 } 238 239 return status; 240 } 241 242 /* Write the given buffer out to the control pipe. */ 243 static int mxuport_send_ctrl_data_urb(struct usb_serial *serial, 244 u8 request, 245 u16 value, u16 index, 246 u8 *data, size_t size) 247 { 248 int status; 249 250 status = usb_control_msg(serial->dev, 251 usb_sndctrlpipe(serial->dev, 0), 252 request, 253 (USB_DIR_OUT | USB_TYPE_VENDOR | 254 USB_RECIP_DEVICE), value, index, 255 data, size, 256 USB_CTRL_SET_TIMEOUT); 257 if (status < 0) { 258 dev_err(&serial->interface->dev, 259 "%s - usb_control_msg failed (%d)\n", 260 __func__, status); 261 return status; 262 } 263 264 if (status != size) { 265 dev_err(&serial->interface->dev, 266 "%s - short write (%d / %zd)\n", 267 __func__, status, size); 268 return -EIO; 269 } 270 271 return 0; 272 } 273 274 /* Send a vendor request without any data */ 275 static int mxuport_send_ctrl_urb(struct usb_serial *serial, 276 u8 request, u16 value, u16 index) 277 { 278 return mxuport_send_ctrl_data_urb(serial, request, value, index, 279 NULL, 0); 280 } 281 282 /* 283 * mxuport_throttle - throttle function of driver 284 * 285 * This function is called by the tty driver when it wants to stop the 286 * data being read from the port. Since all the data comes over one 287 * bulk in endpoint, we cannot stop submitting urbs by setting 288 * port->throttle. Instead tell the device to stop sending us data for 289 * the port. 290 */ 291 static void mxuport_throttle(struct tty_struct *tty) 292 { 293 struct usb_serial_port *port = tty->driver_data; 294 struct usb_serial *serial = port->serial; 295 296 dev_dbg(&port->dev, "%s\n", __func__); 297 298 mxuport_send_ctrl_urb(serial, RQ_VENDOR_SET_RX_HOST_EN, 299 0, port->port_number); 300 } 301 302 /* 303 * mxuport_unthrottle - unthrottle function of driver 304 * 305 * This function is called by the tty driver when it wants to resume 306 * the data being read from the port. Tell the device it can resume 307 * sending us received data from the port. 308 */ 309 static void mxuport_unthrottle(struct tty_struct *tty) 310 { 311 312 struct usb_serial_port *port = tty->driver_data; 313 struct usb_serial *serial = port->serial; 314 315 dev_dbg(&port->dev, "%s\n", __func__); 316 317 mxuport_send_ctrl_urb(serial, RQ_VENDOR_SET_RX_HOST_EN, 318 1, port->port_number); 319 } 320 321 /* 322 * Processes one chunk of data received for a port. Mostly a copy of 323 * usb_serial_generic_process_read_urb(). 324 */ 325 static void mxuport_process_read_urb_data(struct usb_serial_port *port, 326 char *data, int size) 327 { 328 int i; 329 330 if (!port->port.console || !port->sysrq) { 331 tty_insert_flip_string(&port->port, data, size); 332 } else { 333 for (i = 0; i < size; i++, data++) { 334 if (!usb_serial_handle_sysrq_char(port, *data)) 335 tty_insert_flip_char(&port->port, *data, 336 TTY_NORMAL); 337 } 338 } 339 tty_flip_buffer_push(&port->port); 340 } 341 342 static void mxuport_msr_event(struct usb_serial_port *port, u8 buf[4]) 343 { 344 struct mxuport_port *mxport = usb_get_serial_port_data(port); 345 u8 rcv_msr_hold = buf[2] & 0xF0; 346 u16 rcv_msr_event = get_unaligned_be16(buf); 347 unsigned long flags; 348 349 if (rcv_msr_event == 0) 350 return; 351 352 /* Update MSR status */ 353 spin_lock_irqsave(&mxport->spinlock, flags); 354 355 dev_dbg(&port->dev, "%s - current MSR status = 0x%x\n", 356 __func__, mxport->msr_state); 357 358 if (rcv_msr_hold & UART_MSR_CTS) { 359 mxport->msr_state |= UART_MSR_CTS; 360 dev_dbg(&port->dev, "%s - CTS high\n", __func__); 361 } else { 362 mxport->msr_state &= ~UART_MSR_CTS; 363 dev_dbg(&port->dev, "%s - CTS low\n", __func__); 364 } 365 366 if (rcv_msr_hold & UART_MSR_DSR) { 367 mxport->msr_state |= UART_MSR_DSR; 368 dev_dbg(&port->dev, "%s - DSR high\n", __func__); 369 } else { 370 mxport->msr_state &= ~UART_MSR_DSR; 371 dev_dbg(&port->dev, "%s - DSR low\n", __func__); 372 } 373 374 if (rcv_msr_hold & UART_MSR_DCD) { 375 mxport->msr_state |= UART_MSR_DCD; 376 dev_dbg(&port->dev, "%s - DCD high\n", __func__); 377 } else { 378 mxport->msr_state &= ~UART_MSR_DCD; 379 dev_dbg(&port->dev, "%s - DCD low\n", __func__); 380 } 381 spin_unlock_irqrestore(&mxport->spinlock, flags); 382 383 if (rcv_msr_event & 384 (SERIAL_EV_CTS | SERIAL_EV_DSR | SERIAL_EV_RLSD)) { 385 386 if (rcv_msr_event & SERIAL_EV_CTS) { 387 port->icount.cts++; 388 dev_dbg(&port->dev, "%s - CTS change\n", __func__); 389 } 390 391 if (rcv_msr_event & SERIAL_EV_DSR) { 392 port->icount.dsr++; 393 dev_dbg(&port->dev, "%s - DSR change\n", __func__); 394 } 395 396 if (rcv_msr_event & SERIAL_EV_RLSD) { 397 port->icount.dcd++; 398 dev_dbg(&port->dev, "%s - DCD change\n", __func__); 399 } 400 wake_up_interruptible(&port->port.delta_msr_wait); 401 } 402 } 403 404 static void mxuport_lsr_event(struct usb_serial_port *port, u8 buf[4]) 405 { 406 u8 lsr_event = buf[2]; 407 408 if (lsr_event & UART_LSR_BI) { 409 port->icount.brk++; 410 dev_dbg(&port->dev, "%s - break error\n", __func__); 411 } 412 413 if (lsr_event & UART_LSR_FE) { 414 port->icount.frame++; 415 dev_dbg(&port->dev, "%s - frame error\n", __func__); 416 } 417 418 if (lsr_event & UART_LSR_PE) { 419 port->icount.parity++; 420 dev_dbg(&port->dev, "%s - parity error\n", __func__); 421 } 422 423 if (lsr_event & UART_LSR_OE) { 424 port->icount.overrun++; 425 dev_dbg(&port->dev, "%s - overrun error\n", __func__); 426 } 427 } 428 429 /* 430 * When something interesting happens, modem control lines XON/XOFF 431 * etc, the device sends an event. Process these events. 432 */ 433 static void mxuport_process_read_urb_event(struct usb_serial_port *port, 434 u8 buf[4], u32 event) 435 { 436 dev_dbg(&port->dev, "%s - receive event : %04x\n", __func__, event); 437 438 switch (event) { 439 case UPORT_EVENT_SEND_NEXT: 440 /* 441 * Sent as part of the flow control on device buffers. 442 * Not currently used. 443 */ 444 break; 445 case UPORT_EVENT_MSR: 446 mxuport_msr_event(port, buf); 447 break; 448 case UPORT_EVENT_LSR: 449 mxuport_lsr_event(port, buf); 450 break; 451 case UPORT_EVENT_MCR: 452 /* 453 * Event to indicate a change in XON/XOFF from the 454 * peer. Currently not used. We just continue 455 * sending the device data and it will buffer it if 456 * needed. This event could be used for flow control 457 * between the host and the device. 458 */ 459 break; 460 default: 461 dev_dbg(&port->dev, "Unexpected event\n"); 462 break; 463 } 464 } 465 466 /* 467 * One URB can contain data for multiple ports. Demultiplex the data, 468 * checking the port exists, is opened and the message is valid. 469 */ 470 static void mxuport_process_read_urb_demux_data(struct urb *urb) 471 { 472 struct usb_serial_port *port = urb->context; 473 struct usb_serial *serial = port->serial; 474 u8 *data = urb->transfer_buffer; 475 u8 *end = data + urb->actual_length; 476 struct usb_serial_port *demux_port; 477 u8 *ch; 478 u16 rcv_port; 479 u16 rcv_len; 480 481 while (data < end) { 482 if (data + HEADER_SIZE > end) { 483 dev_warn(&port->dev, "%s - message with short header\n", 484 __func__); 485 return; 486 } 487 488 rcv_port = get_unaligned_be16(data); 489 if (rcv_port >= serial->num_ports) { 490 dev_warn(&port->dev, "%s - message for invalid port\n", 491 __func__); 492 return; 493 } 494 495 demux_port = serial->port[rcv_port]; 496 rcv_len = get_unaligned_be16(data + 2); 497 if (!rcv_len || data + HEADER_SIZE + rcv_len > end) { 498 dev_warn(&port->dev, "%s - short data\n", __func__); 499 return; 500 } 501 502 if (tty_port_initialized(&demux_port->port)) { 503 ch = data + HEADER_SIZE; 504 mxuport_process_read_urb_data(demux_port, ch, rcv_len); 505 } else { 506 dev_dbg(&demux_port->dev, "%s - data for closed port\n", 507 __func__); 508 } 509 data += HEADER_SIZE + rcv_len; 510 } 511 } 512 513 /* 514 * One URB can contain events for multiple ports. Demultiplex the event, 515 * checking the port exists, and is opened. 516 */ 517 static void mxuport_process_read_urb_demux_event(struct urb *urb) 518 { 519 struct usb_serial_port *port = urb->context; 520 struct usb_serial *serial = port->serial; 521 u8 *data = urb->transfer_buffer; 522 u8 *end = data + urb->actual_length; 523 struct usb_serial_port *demux_port; 524 u8 *ch; 525 u16 rcv_port; 526 u16 rcv_event; 527 528 while (data < end) { 529 if (data + EVENT_LENGTH > end) { 530 dev_warn(&port->dev, "%s - message with short event\n", 531 __func__); 532 return; 533 } 534 535 rcv_port = get_unaligned_be16(data); 536 if (rcv_port >= serial->num_ports) { 537 dev_warn(&port->dev, "%s - message for invalid port\n", 538 __func__); 539 return; 540 } 541 542 demux_port = serial->port[rcv_port]; 543 if (tty_port_initialized(&demux_port->port)) { 544 ch = data + HEADER_SIZE; 545 rcv_event = get_unaligned_be16(data + 2); 546 mxuport_process_read_urb_event(demux_port, ch, 547 rcv_event); 548 } else { 549 dev_dbg(&demux_port->dev, 550 "%s - event for closed port\n", __func__); 551 } 552 data += EVENT_LENGTH; 553 } 554 } 555 556 /* 557 * This is called when we have received data on the bulk in 558 * endpoint. Depending on which port it was received on, it can 559 * contain serial data or events. 560 */ 561 static void mxuport_process_read_urb(struct urb *urb) 562 { 563 struct usb_serial_port *port = urb->context; 564 struct usb_serial *serial = port->serial; 565 566 if (port == serial->port[0]) 567 mxuport_process_read_urb_demux_data(urb); 568 569 if (port == serial->port[1]) 570 mxuport_process_read_urb_demux_event(urb); 571 } 572 573 /* 574 * Ask the device how many bytes it has queued to be sent out. If 575 * there are none, return true. 576 */ 577 static bool mxuport_tx_empty(struct usb_serial_port *port) 578 { 579 struct usb_serial *serial = port->serial; 580 bool is_empty = true; 581 u32 txlen; 582 u8 *len_buf; 583 int err; 584 585 len_buf = kzalloc(4, GFP_KERNEL); 586 if (!len_buf) 587 goto out; 588 589 err = mxuport_recv_ctrl_urb(serial, RQ_VENDOR_GET_OUTQUEUE, 0, 590 port->port_number, len_buf, 4); 591 if (err < 0) 592 goto out; 593 594 txlen = get_unaligned_be32(len_buf); 595 dev_dbg(&port->dev, "%s - tx len = %u\n", __func__, txlen); 596 597 if (txlen != 0) 598 is_empty = false; 599 600 out: 601 kfree(len_buf); 602 return is_empty; 603 } 604 605 static int mxuport_set_mcr(struct usb_serial_port *port, u8 mcr_state) 606 { 607 struct usb_serial *serial = port->serial; 608 int err; 609 610 dev_dbg(&port->dev, "%s - %02x\n", __func__, mcr_state); 611 612 err = mxuport_send_ctrl_urb(serial, RQ_VENDOR_SET_MCR, 613 mcr_state, port->port_number); 614 if (err) 615 dev_err(&port->dev, "%s - failed to change MCR\n", __func__); 616 617 return err; 618 } 619 620 static int mxuport_set_dtr(struct usb_serial_port *port, int on) 621 { 622 struct mxuport_port *mxport = usb_get_serial_port_data(port); 623 struct usb_serial *serial = port->serial; 624 int err; 625 626 mutex_lock(&mxport->mutex); 627 628 err = mxuport_send_ctrl_urb(serial, RQ_VENDOR_SET_DTR, 629 !!on, port->port_number); 630 if (!err) { 631 if (on) 632 mxport->mcr_state |= UART_MCR_DTR; 633 else 634 mxport->mcr_state &= ~UART_MCR_DTR; 635 } 636 637 mutex_unlock(&mxport->mutex); 638 639 return err; 640 } 641 642 static int mxuport_set_rts(struct usb_serial_port *port, u8 state) 643 { 644 struct mxuport_port *mxport = usb_get_serial_port_data(port); 645 struct usb_serial *serial = port->serial; 646 int err; 647 u8 mcr_state; 648 649 mutex_lock(&mxport->mutex); 650 mcr_state = mxport->mcr_state; 651 652 switch (state) { 653 case MX_RTS_DISABLE: 654 mcr_state &= ~UART_MCR_RTS; 655 break; 656 case MX_RTS_ENABLE: 657 mcr_state |= UART_MCR_RTS; 658 break; 659 case MX_RTS_HW: 660 /* 661 * Do not update mxport->mcr_state when doing hardware 662 * flow control. 663 */ 664 break; 665 default: 666 /* 667 * Should not happen, but somebody might try passing 668 * MX_RTS_NO_CHANGE, which is not valid. 669 */ 670 err = -EINVAL; 671 goto out; 672 } 673 err = mxuport_send_ctrl_urb(serial, RQ_VENDOR_SET_RTS, 674 state, port->port_number); 675 if (!err) 676 mxport->mcr_state = mcr_state; 677 678 out: 679 mutex_unlock(&mxport->mutex); 680 681 return err; 682 } 683 684 static void mxuport_dtr_rts(struct usb_serial_port *port, int on) 685 { 686 struct mxuport_port *mxport = usb_get_serial_port_data(port); 687 u8 mcr_state; 688 int err; 689 690 mutex_lock(&mxport->mutex); 691 mcr_state = mxport->mcr_state; 692 693 if (on) 694 mcr_state |= (UART_MCR_RTS | UART_MCR_DTR); 695 else 696 mcr_state &= ~(UART_MCR_RTS | UART_MCR_DTR); 697 698 err = mxuport_set_mcr(port, mcr_state); 699 if (!err) 700 mxport->mcr_state = mcr_state; 701 702 mutex_unlock(&mxport->mutex); 703 } 704 705 static int mxuport_tiocmset(struct tty_struct *tty, unsigned int set, 706 unsigned int clear) 707 { 708 struct usb_serial_port *port = tty->driver_data; 709 struct mxuport_port *mxport = usb_get_serial_port_data(port); 710 int err; 711 u8 mcr_state; 712 713 mutex_lock(&mxport->mutex); 714 mcr_state = mxport->mcr_state; 715 716 if (set & TIOCM_RTS) 717 mcr_state |= UART_MCR_RTS; 718 719 if (set & TIOCM_DTR) 720 mcr_state |= UART_MCR_DTR; 721 722 if (clear & TIOCM_RTS) 723 mcr_state &= ~UART_MCR_RTS; 724 725 if (clear & TIOCM_DTR) 726 mcr_state &= ~UART_MCR_DTR; 727 728 err = mxuport_set_mcr(port, mcr_state); 729 if (!err) 730 mxport->mcr_state = mcr_state; 731 732 mutex_unlock(&mxport->mutex); 733 734 return err; 735 } 736 737 static int mxuport_tiocmget(struct tty_struct *tty) 738 { 739 struct mxuport_port *mxport; 740 struct usb_serial_port *port = tty->driver_data; 741 unsigned int result; 742 unsigned long flags; 743 unsigned int msr; 744 unsigned int mcr; 745 746 mxport = usb_get_serial_port_data(port); 747 748 mutex_lock(&mxport->mutex); 749 spin_lock_irqsave(&mxport->spinlock, flags); 750 751 msr = mxport->msr_state; 752 mcr = mxport->mcr_state; 753 754 spin_unlock_irqrestore(&mxport->spinlock, flags); 755 mutex_unlock(&mxport->mutex); 756 757 result = (((mcr & UART_MCR_DTR) ? TIOCM_DTR : 0) | /* 0x002 */ 758 ((mcr & UART_MCR_RTS) ? TIOCM_RTS : 0) | /* 0x004 */ 759 ((msr & UART_MSR_CTS) ? TIOCM_CTS : 0) | /* 0x020 */ 760 ((msr & UART_MSR_DCD) ? TIOCM_CAR : 0) | /* 0x040 */ 761 ((msr & UART_MSR_RI) ? TIOCM_RI : 0) | /* 0x080 */ 762 ((msr & UART_MSR_DSR) ? TIOCM_DSR : 0)); /* 0x100 */ 763 764 dev_dbg(&port->dev, "%s - 0x%04x\n", __func__, result); 765 766 return result; 767 } 768 769 static int mxuport_set_termios_flow(struct tty_struct *tty, 770 struct ktermios *old_termios, 771 struct usb_serial_port *port, 772 struct usb_serial *serial) 773 { 774 u8 xon = START_CHAR(tty); 775 u8 xoff = STOP_CHAR(tty); 776 int enable; 777 int err; 778 u8 *buf; 779 u8 rts; 780 781 buf = kmalloc(2, GFP_KERNEL); 782 if (!buf) 783 return -ENOMEM; 784 785 /* S/W flow control settings */ 786 if (I_IXOFF(tty) || I_IXON(tty)) { 787 enable = 1; 788 buf[0] = xon; 789 buf[1] = xoff; 790 791 err = mxuport_send_ctrl_data_urb(serial, RQ_VENDOR_SET_CHARS, 792 0, port->port_number, 793 buf, 2); 794 if (err) 795 goto out; 796 797 dev_dbg(&port->dev, "%s - XON = 0x%02x, XOFF = 0x%02x\n", 798 __func__, xon, xoff); 799 } else { 800 enable = 0; 801 } 802 803 err = mxuport_send_ctrl_urb(serial, RQ_VENDOR_SET_XONXOFF, 804 enable, port->port_number); 805 if (err) 806 goto out; 807 808 rts = MX_RTS_NO_CHANGE; 809 810 /* H/W flow control settings */ 811 if (!old_termios || 812 C_CRTSCTS(tty) != (old_termios->c_cflag & CRTSCTS)) { 813 if (C_CRTSCTS(tty)) 814 rts = MX_RTS_HW; 815 else 816 rts = MX_RTS_ENABLE; 817 } 818 819 if (C_BAUD(tty)) { 820 if (old_termios && (old_termios->c_cflag & CBAUD) == B0) { 821 /* Raise DTR and RTS */ 822 if (C_CRTSCTS(tty)) 823 rts = MX_RTS_HW; 824 else 825 rts = MX_RTS_ENABLE; 826 mxuport_set_dtr(port, 1); 827 } 828 } else { 829 /* Drop DTR and RTS */ 830 rts = MX_RTS_DISABLE; 831 mxuport_set_dtr(port, 0); 832 } 833 834 if (rts != MX_RTS_NO_CHANGE) 835 err = mxuport_set_rts(port, rts); 836 837 out: 838 kfree(buf); 839 return err; 840 } 841 842 static void mxuport_set_termios(struct tty_struct *tty, 843 struct usb_serial_port *port, 844 struct ktermios *old_termios) 845 { 846 struct usb_serial *serial = port->serial; 847 u8 *buf; 848 u8 data_bits; 849 u8 stop_bits; 850 u8 parity; 851 int baud; 852 int err; 853 854 if (old_termios && 855 !tty_termios_hw_change(&tty->termios, old_termios) && 856 tty->termios.c_iflag == old_termios->c_iflag) { 857 dev_dbg(&port->dev, "%s - nothing to change\n", __func__); 858 return; 859 } 860 861 buf = kmalloc(4, GFP_KERNEL); 862 if (!buf) 863 return; 864 865 /* Set data bit of termios */ 866 switch (C_CSIZE(tty)) { 867 case CS5: 868 data_bits = MX_WORDLENGTH_5; 869 break; 870 case CS6: 871 data_bits = MX_WORDLENGTH_6; 872 break; 873 case CS7: 874 data_bits = MX_WORDLENGTH_7; 875 break; 876 case CS8: 877 default: 878 data_bits = MX_WORDLENGTH_8; 879 break; 880 } 881 882 /* Set parity of termios */ 883 if (C_PARENB(tty)) { 884 if (C_CMSPAR(tty)) { 885 if (C_PARODD(tty)) 886 parity = MX_PARITY_MARK; 887 else 888 parity = MX_PARITY_SPACE; 889 } else { 890 if (C_PARODD(tty)) 891 parity = MX_PARITY_ODD; 892 else 893 parity = MX_PARITY_EVEN; 894 } 895 } else { 896 parity = MX_PARITY_NONE; 897 } 898 899 /* Set stop bit of termios */ 900 if (C_CSTOPB(tty)) 901 stop_bits = MX_STOP_BITS_2; 902 else 903 stop_bits = MX_STOP_BITS_1; 904 905 buf[0] = data_bits; 906 buf[1] = parity; 907 buf[2] = stop_bits; 908 buf[3] = 0; 909 910 err = mxuport_send_ctrl_data_urb(serial, RQ_VENDOR_SET_LINE, 911 0, port->port_number, buf, 4); 912 if (err) 913 goto out; 914 915 err = mxuport_set_termios_flow(tty, old_termios, port, serial); 916 if (err) 917 goto out; 918 919 baud = tty_get_baud_rate(tty); 920 if (!baud) 921 baud = 9600; 922 923 /* Note: Little Endian */ 924 put_unaligned_le32(baud, buf); 925 926 err = mxuport_send_ctrl_data_urb(serial, RQ_VENDOR_SET_BAUD, 927 0, port->port_number, 928 buf, 4); 929 if (err) 930 goto out; 931 932 dev_dbg(&port->dev, "baud_rate : %d\n", baud); 933 dev_dbg(&port->dev, "data_bits : %d\n", data_bits); 934 dev_dbg(&port->dev, "parity : %d\n", parity); 935 dev_dbg(&port->dev, "stop_bits : %d\n", stop_bits); 936 937 out: 938 kfree(buf); 939 } 940 941 /* 942 * Determine how many ports this device has dynamically. It will be 943 * called after the probe() callback is called, but before attach(). 944 */ 945 static int mxuport_calc_num_ports(struct usb_serial *serial, 946 struct usb_serial_endpoints *epds) 947 { 948 unsigned long features = (unsigned long)usb_get_serial_data(serial); 949 int num_ports; 950 int i; 951 952 if (features & MX_UPORT_2_PORT) { 953 num_ports = 2; 954 } else if (features & MX_UPORT_4_PORT) { 955 num_ports = 4; 956 } else if (features & MX_UPORT_8_PORT) { 957 num_ports = 8; 958 } else if (features & MX_UPORT_16_PORT) { 959 num_ports = 16; 960 } else { 961 dev_warn(&serial->interface->dev, 962 "unknown device, assuming two ports\n"); 963 num_ports = 2; 964 } 965 966 /* 967 * Setup bulk-out endpoint multiplexing. All ports share the same 968 * bulk-out endpoint. 969 */ 970 BUILD_BUG_ON(ARRAY_SIZE(epds->bulk_out) < 16); 971 972 for (i = 1; i < num_ports; ++i) 973 epds->bulk_out[i] = epds->bulk_out[0]; 974 975 epds->num_bulk_out = num_ports; 976 977 return num_ports; 978 } 979 980 /* Get the version of the firmware currently running. */ 981 static int mxuport_get_fw_version(struct usb_serial *serial, u32 *version) 982 { 983 u8 *ver_buf; 984 int err; 985 986 ver_buf = kzalloc(4, GFP_KERNEL); 987 if (!ver_buf) 988 return -ENOMEM; 989 990 /* Get firmware version from SDRAM */ 991 err = mxuport_recv_ctrl_urb(serial, RQ_VENDOR_GET_VERSION, 0, 0, 992 ver_buf, 4); 993 if (err != 4) { 994 err = -EIO; 995 goto out; 996 } 997 998 *version = (ver_buf[0] << 16) | (ver_buf[1] << 8) | ver_buf[2]; 999 err = 0; 1000 out: 1001 kfree(ver_buf); 1002 return err; 1003 } 1004 1005 /* Given a firmware blob, download it to the device. */ 1006 static int mxuport_download_fw(struct usb_serial *serial, 1007 const struct firmware *fw_p) 1008 { 1009 u8 *fw_buf; 1010 size_t txlen; 1011 size_t fwidx; 1012 int err; 1013 1014 fw_buf = kmalloc(DOWN_BLOCK_SIZE, GFP_KERNEL); 1015 if (!fw_buf) 1016 return -ENOMEM; 1017 1018 dev_dbg(&serial->interface->dev, "Starting firmware download...\n"); 1019 err = mxuport_send_ctrl_urb(serial, RQ_VENDOR_START_FW_DOWN, 0, 0); 1020 if (err) 1021 goto out; 1022 1023 fwidx = 0; 1024 do { 1025 txlen = min_t(size_t, (fw_p->size - fwidx), DOWN_BLOCK_SIZE); 1026 1027 memcpy(fw_buf, &fw_p->data[fwidx], txlen); 1028 err = mxuport_send_ctrl_data_urb(serial, RQ_VENDOR_FW_DATA, 1029 0, 0, fw_buf, txlen); 1030 if (err) { 1031 mxuport_send_ctrl_urb(serial, RQ_VENDOR_STOP_FW_DOWN, 1032 0, 0); 1033 goto out; 1034 } 1035 1036 fwidx += txlen; 1037 usleep_range(1000, 2000); 1038 1039 } while (fwidx < fw_p->size); 1040 1041 msleep(1000); 1042 err = mxuport_send_ctrl_urb(serial, RQ_VENDOR_STOP_FW_DOWN, 0, 0); 1043 if (err) 1044 goto out; 1045 1046 msleep(1000); 1047 err = mxuport_send_ctrl_urb(serial, RQ_VENDOR_QUERY_FW_READY, 0, 0); 1048 1049 out: 1050 kfree(fw_buf); 1051 return err; 1052 } 1053 1054 static int mxuport_probe(struct usb_serial *serial, 1055 const struct usb_device_id *id) 1056 { 1057 u16 productid = le16_to_cpu(serial->dev->descriptor.idProduct); 1058 const struct firmware *fw_p = NULL; 1059 u32 version; 1060 int local_ver; 1061 char buf[32]; 1062 int err; 1063 1064 /* Load our firmware */ 1065 err = mxuport_send_ctrl_urb(serial, RQ_VENDOR_QUERY_FW_CONFIG, 0, 0); 1066 if (err) { 1067 mxuport_send_ctrl_urb(serial, RQ_VENDOR_RESET_DEVICE, 0, 0); 1068 return err; 1069 } 1070 1071 err = mxuport_get_fw_version(serial, &version); 1072 if (err < 0) 1073 return err; 1074 1075 dev_dbg(&serial->interface->dev, "Device firmware version v%x.%x.%x\n", 1076 (version & 0xff0000) >> 16, 1077 (version & 0xff00) >> 8, 1078 (version & 0xff)); 1079 1080 snprintf(buf, sizeof(buf) - 1, "moxa/moxa-%04x.fw", productid); 1081 1082 err = request_firmware(&fw_p, buf, &serial->interface->dev); 1083 if (err) { 1084 dev_warn(&serial->interface->dev, "Firmware %s not found\n", 1085 buf); 1086 1087 /* Use the firmware already in the device */ 1088 err = 0; 1089 } else { 1090 local_ver = ((fw_p->data[VER_ADDR_1] << 16) | 1091 (fw_p->data[VER_ADDR_2] << 8) | 1092 fw_p->data[VER_ADDR_3]); 1093 dev_dbg(&serial->interface->dev, 1094 "Available firmware version v%x.%x.%x\n", 1095 fw_p->data[VER_ADDR_1], fw_p->data[VER_ADDR_2], 1096 fw_p->data[VER_ADDR_3]); 1097 if (local_ver > version) { 1098 err = mxuport_download_fw(serial, fw_p); 1099 if (err) 1100 goto out; 1101 err = mxuport_get_fw_version(serial, &version); 1102 if (err < 0) 1103 goto out; 1104 } 1105 } 1106 1107 dev_info(&serial->interface->dev, 1108 "Using device firmware version v%x.%x.%x\n", 1109 (version & 0xff0000) >> 16, 1110 (version & 0xff00) >> 8, 1111 (version & 0xff)); 1112 1113 /* 1114 * Contains the features of this hardware. Store away for 1115 * later use, eg, number of ports. 1116 */ 1117 usb_set_serial_data(serial, (void *)id->driver_info); 1118 out: 1119 if (fw_p) 1120 release_firmware(fw_p); 1121 return err; 1122 } 1123 1124 1125 static int mxuport_port_probe(struct usb_serial_port *port) 1126 { 1127 struct usb_serial *serial = port->serial; 1128 struct mxuport_port *mxport; 1129 int err; 1130 1131 mxport = devm_kzalloc(&port->dev, sizeof(struct mxuport_port), 1132 GFP_KERNEL); 1133 if (!mxport) 1134 return -ENOMEM; 1135 1136 mutex_init(&mxport->mutex); 1137 spin_lock_init(&mxport->spinlock); 1138 1139 /* Set the port private data */ 1140 usb_set_serial_port_data(port, mxport); 1141 1142 /* Set FIFO (Enable) */ 1143 err = mxuport_send_ctrl_urb(serial, RQ_VENDOR_SET_FIFO_DISABLE, 1144 0, port->port_number); 1145 if (err) 1146 return err; 1147 1148 /* Set transmission mode (Hi-Performance) */ 1149 err = mxuport_send_ctrl_urb(serial, RQ_VENDOR_SET_HIGH_PERFOR, 1150 0, port->port_number); 1151 if (err) 1152 return err; 1153 1154 /* Set interface (RS-232) */ 1155 return mxuport_send_ctrl_urb(serial, RQ_VENDOR_SET_INTERFACE, 1156 MX_INT_RS232, 1157 port->port_number); 1158 } 1159 1160 static int mxuport_attach(struct usb_serial *serial) 1161 { 1162 struct usb_serial_port *port0 = serial->port[0]; 1163 struct usb_serial_port *port1 = serial->port[1]; 1164 int err; 1165 1166 /* 1167 * All data from the ports is received on the first bulk in 1168 * endpoint, with a multiplex header. The second bulk in is 1169 * used for events. 1170 * 1171 * Start to read from the device. 1172 */ 1173 err = usb_serial_generic_submit_read_urbs(port0, GFP_KERNEL); 1174 if (err) 1175 return err; 1176 1177 err = usb_serial_generic_submit_read_urbs(port1, GFP_KERNEL); 1178 if (err) { 1179 usb_serial_generic_close(port0); 1180 return err; 1181 } 1182 1183 return 0; 1184 } 1185 1186 static void mxuport_release(struct usb_serial *serial) 1187 { 1188 struct usb_serial_port *port0 = serial->port[0]; 1189 struct usb_serial_port *port1 = serial->port[1]; 1190 1191 usb_serial_generic_close(port1); 1192 usb_serial_generic_close(port0); 1193 } 1194 1195 static int mxuport_open(struct tty_struct *tty, struct usb_serial_port *port) 1196 { 1197 struct mxuport_port *mxport = usb_get_serial_port_data(port); 1198 struct usb_serial *serial = port->serial; 1199 int err; 1200 1201 /* Set receive host (enable) */ 1202 err = mxuport_send_ctrl_urb(serial, RQ_VENDOR_SET_RX_HOST_EN, 1203 1, port->port_number); 1204 if (err) 1205 return err; 1206 1207 err = mxuport_send_ctrl_urb(serial, RQ_VENDOR_SET_OPEN, 1208 1, port->port_number); 1209 if (err) { 1210 mxuport_send_ctrl_urb(serial, RQ_VENDOR_SET_RX_HOST_EN, 1211 0, port->port_number); 1212 return err; 1213 } 1214 1215 /* Initial port termios */ 1216 if (tty) 1217 mxuport_set_termios(tty, port, NULL); 1218 1219 /* 1220 * TODO: use RQ_VENDOR_GET_MSR, once we know what it 1221 * returns. 1222 */ 1223 mxport->msr_state = 0; 1224 1225 return err; 1226 } 1227 1228 static void mxuport_close(struct usb_serial_port *port) 1229 { 1230 struct usb_serial *serial = port->serial; 1231 1232 mxuport_send_ctrl_urb(serial, RQ_VENDOR_SET_OPEN, 0, 1233 port->port_number); 1234 1235 mxuport_send_ctrl_urb(serial, RQ_VENDOR_SET_RX_HOST_EN, 0, 1236 port->port_number); 1237 } 1238 1239 /* Send a break to the port. */ 1240 static void mxuport_break_ctl(struct tty_struct *tty, int break_state) 1241 { 1242 struct usb_serial_port *port = tty->driver_data; 1243 struct usb_serial *serial = port->serial; 1244 int enable; 1245 1246 if (break_state == -1) { 1247 enable = 1; 1248 dev_dbg(&port->dev, "%s - sending break\n", __func__); 1249 } else { 1250 enable = 0; 1251 dev_dbg(&port->dev, "%s - clearing break\n", __func__); 1252 } 1253 1254 mxuport_send_ctrl_urb(serial, RQ_VENDOR_SET_BREAK, 1255 enable, port->port_number); 1256 } 1257 1258 static int mxuport_resume(struct usb_serial *serial) 1259 { 1260 struct usb_serial_port *port; 1261 int c = 0; 1262 int i; 1263 int r; 1264 1265 for (i = 0; i < 2; i++) { 1266 port = serial->port[i]; 1267 1268 r = usb_serial_generic_submit_read_urbs(port, GFP_NOIO); 1269 if (r < 0) 1270 c++; 1271 } 1272 1273 for (i = 0; i < serial->num_ports; i++) { 1274 port = serial->port[i]; 1275 if (!tty_port_initialized(&port->port)) 1276 continue; 1277 1278 r = usb_serial_generic_write_start(port, GFP_NOIO); 1279 if (r < 0) 1280 c++; 1281 } 1282 1283 return c ? -EIO : 0; 1284 } 1285 1286 static struct usb_serial_driver mxuport_device = { 1287 .driver = { 1288 .owner = THIS_MODULE, 1289 .name = "mxuport", 1290 }, 1291 .description = "MOXA UPort", 1292 .id_table = mxuport_idtable, 1293 .num_bulk_in = 2, 1294 .num_bulk_out = 1, 1295 .probe = mxuport_probe, 1296 .port_probe = mxuport_port_probe, 1297 .attach = mxuport_attach, 1298 .release = mxuport_release, 1299 .calc_num_ports = mxuport_calc_num_ports, 1300 .open = mxuport_open, 1301 .close = mxuport_close, 1302 .set_termios = mxuport_set_termios, 1303 .break_ctl = mxuport_break_ctl, 1304 .tx_empty = mxuport_tx_empty, 1305 .tiocmiwait = usb_serial_generic_tiocmiwait, 1306 .get_icount = usb_serial_generic_get_icount, 1307 .throttle = mxuport_throttle, 1308 .unthrottle = mxuport_unthrottle, 1309 .tiocmget = mxuport_tiocmget, 1310 .tiocmset = mxuport_tiocmset, 1311 .dtr_rts = mxuport_dtr_rts, 1312 .process_read_urb = mxuport_process_read_urb, 1313 .prepare_write_buffer = mxuport_prepare_write_buffer, 1314 .resume = mxuport_resume, 1315 }; 1316 1317 static struct usb_serial_driver *const serial_drivers[] = { 1318 &mxuport_device, NULL 1319 }; 1320 1321 module_usb_serial_driver(serial_drivers, mxuport_idtable); 1322 1323 MODULE_AUTHOR("Andrew Lunn <andrew@lunn.ch>"); 1324 MODULE_AUTHOR("<support@moxa.com>"); 1325 MODULE_LICENSE("GPL"); 1326