1 /* 2 * Definitions for the FTDI USB Single Port Serial Converter - 3 * known as FTDI_SIO (Serial Input/Output application of the chipset) 4 * 5 * The example I have is known as the USC-1000 which is available from 6 * http://www.dse.co.nz - cat no XH4214 It looks similar to this: 7 * http://www.dansdata.com/usbser.htm but I can't be sure There are other 8 * USC-1000s which don't look like my device though so beware! 9 * 10 * The device is based on the FTDI FT8U100AX chip. It has a DB25 on one side, 11 * USB on the other. 12 * 13 * Thanx to FTDI (http://www.ftdi.co.uk) for so kindly providing details 14 * of the protocol required to talk to the device and ongoing assistence 15 * during development. 16 * 17 * Bill Ryder - bryder@sgi.com formerly of Silicon Graphics, Inc.- wrote the 18 * FTDI_SIO implementation. 19 * 20 * Philipp G�hring - pg@futureware.at - added the Device ID of the USB relais 21 * from Rudolf Gugler 22 * 23 */ 24 25 #define FTDI_VID 0x0403 /* Vendor Id */ 26 #define FTDI_SIO_PID 0x8372 /* Product Id SIO application of 8U100AX */ 27 #define FTDI_8U232AM_PID 0x6001 /* Similar device to SIO above */ 28 #define FTDI_8U232AM_ALT_PID 0x6006 /* FTDI's alternate PID for above */ 29 #define FTDI_8U2232C_PID 0x6010 /* Dual channel device */ 30 #define FTDI_RELAIS_PID 0xFA10 /* Relais device from Rudolf Gugler */ 31 #define FTDI_NF_RIC_VID 0x0DCD /* Vendor Id */ 32 #define FTDI_NF_RIC_PID 0x0001 /* Product Id */ 33 34 35 /* www.irtrans.de device */ 36 #define FTDI_IRTRANS_PID 0xFC60 /* Product Id */ 37 38 39 /* www.thoughttechnology.com/ TT-USB provide with procomp use ftdi_sio */ 40 #define FTDI_TTUSB_PID 0xFF20 /* Product Id */ 41 42 /* www.crystalfontz.com devices - thanx for providing free devices for evaluation ! */ 43 /* they use the ftdi chipset for the USB interface and the vendor id is the same */ 44 #define FTDI_XF_632_PID 0xFC08 /* 632: 16x2 Character Display */ 45 #define FTDI_XF_634_PID 0xFC09 /* 634: 20x4 Character Display */ 46 #define FTDI_XF_547_PID 0xFC0A /* 547: Two line Display */ 47 #define FTDI_XF_633_PID 0xFC0B /* 633: 16x2 Character Display with Keys */ 48 #define FTDI_XF_631_PID 0xFC0C /* 631: 20x2 Character Display */ 49 #define FTDI_XF_635_PID 0xFC0D /* 635: 20x4 Character Display */ 50 #define FTDI_XF_640_PID 0xFC0E /* 640: Two line Display */ 51 #define FTDI_XF_642_PID 0xFC0F /* 642: Two line Display */ 52 53 /* Video Networks Limited / Homechoice in the UK use an ftdi-based device for their 1Mb */ 54 /* broadband internet service. The following PID is exhibited by the usb device supplied */ 55 /* (the VID is the standard ftdi vid (FTDI_VID) */ 56 #define FTDI_VNHCPCUSB_D_PID 0xfe38 /* Product Id */ 57 58 /* 59 * PCDJ use ftdi based dj-controllers. The following PID is for their DAC-2 device 60 * http://www.pcdjhardware.com/DAC2.asp (PID sent by Wouter Paesen) 61 * (the VID is the standard ftdi vid (FTDI_VID) */ 62 #define FTDI_PCDJ_DAC2_PID 0xFA88 63 64 /* 65 * The following are the values for the Matrix Orbital LCD displays, 66 * which are the FT232BM ( similar to the 8U232AM ) 67 */ 68 #define FTDI_MTXORB_0_PID 0xFA00 /* Matrix Orbital Product Id */ 69 #define FTDI_MTXORB_1_PID 0xFA01 /* Matrix Orbital Product Id */ 70 #define FTDI_MTXORB_2_PID 0xFA02 /* Matrix Orbital Product Id */ 71 #define FTDI_MTXORB_3_PID 0xFA03 /* Matrix Orbital Product Id */ 72 #define FTDI_MTXORB_4_PID 0xFA04 /* Matrix Orbital Product Id */ 73 #define FTDI_MTXORB_5_PID 0xFA05 /* Matrix Orbital Product Id */ 74 #define FTDI_MTXORB_6_PID 0xFA06 /* Matrix Orbital Product Id */ 75 76 /* Interbiometrics USB I/O Board */ 77 /* Developed for Interbiometrics by Rudolf Gugler */ 78 #define INTERBIOMETRICS_VID 0x1209 79 #define INTERBIOMETRICS_IOBOARD_PID 0x1002 80 #define INTERBIOMETRICS_MINI_IOBOARD_PID 0x1006 81 82 /* 83 * The following are the values for the Perle Systems 84 * UltraPort USB serial converters 85 */ 86 #define FTDI_PERLE_ULTRAPORT_PID 0xF0C0 /* Perle UltraPort Product Id */ 87 88 /* 89 * The following are the values for the Sealevel SeaLINK+ adapters. 90 * (Original list sent by Tuan Hoang. Ian Abbott renamed the macros and 91 * removed some PIDs that don't seem to match any existing products.) 92 */ 93 #define SEALEVEL_VID 0x0c52 /* Sealevel Vendor ID */ 94 #define SEALEVEL_2101_PID 0x2101 /* SeaLINK+232 (2101/2105) */ 95 #define SEALEVEL_2102_PID 0x2102 /* SeaLINK+485 (2102) */ 96 #define SEALEVEL_2103_PID 0x2103 /* SeaLINK+232I (2103) */ 97 #define SEALEVEL_2104_PID 0x2104 /* SeaLINK+485I (2104) */ 98 #define SEALEVEL_2201_1_PID 0x2211 /* SeaPORT+2/232 (2201) Port 1 */ 99 #define SEALEVEL_2201_2_PID 0x2221 /* SeaPORT+2/232 (2201) Port 2 */ 100 #define SEALEVEL_2202_1_PID 0x2212 /* SeaPORT+2/485 (2202) Port 1 */ 101 #define SEALEVEL_2202_2_PID 0x2222 /* SeaPORT+2/485 (2202) Port 2 */ 102 #define SEALEVEL_2203_1_PID 0x2213 /* SeaPORT+2 (2203) Port 1 */ 103 #define SEALEVEL_2203_2_PID 0x2223 /* SeaPORT+2 (2203) Port 2 */ 104 #define SEALEVEL_2401_1_PID 0x2411 /* SeaPORT+4/232 (2401) Port 1 */ 105 #define SEALEVEL_2401_2_PID 0x2421 /* SeaPORT+4/232 (2401) Port 2 */ 106 #define SEALEVEL_2401_3_PID 0x2431 /* SeaPORT+4/232 (2401) Port 3 */ 107 #define SEALEVEL_2401_4_PID 0x2441 /* SeaPORT+4/232 (2401) Port 4 */ 108 #define SEALEVEL_2402_1_PID 0x2412 /* SeaPORT+4/485 (2402) Port 1 */ 109 #define SEALEVEL_2402_2_PID 0x2422 /* SeaPORT+4/485 (2402) Port 2 */ 110 #define SEALEVEL_2402_3_PID 0x2432 /* SeaPORT+4/485 (2402) Port 3 */ 111 #define SEALEVEL_2402_4_PID 0x2442 /* SeaPORT+4/485 (2402) Port 4 */ 112 #define SEALEVEL_2403_1_PID 0x2413 /* SeaPORT+4 (2403) Port 1 */ 113 #define SEALEVEL_2403_2_PID 0x2423 /* SeaPORT+4 (2403) Port 2 */ 114 #define SEALEVEL_2403_3_PID 0x2433 /* SeaPORT+4 (2403) Port 3 */ 115 #define SEALEVEL_2403_4_PID 0x2443 /* SeaPORT+4 (2403) Port 4 */ 116 #define SEALEVEL_2801_1_PID 0X2811 /* SeaLINK+8/232 (2801) Port 1 */ 117 #define SEALEVEL_2801_2_PID 0X2821 /* SeaLINK+8/232 (2801) Port 2 */ 118 #define SEALEVEL_2801_3_PID 0X2831 /* SeaLINK+8/232 (2801) Port 3 */ 119 #define SEALEVEL_2801_4_PID 0X2841 /* SeaLINK+8/232 (2801) Port 4 */ 120 #define SEALEVEL_2801_5_PID 0X2851 /* SeaLINK+8/232 (2801) Port 5 */ 121 #define SEALEVEL_2801_6_PID 0X2861 /* SeaLINK+8/232 (2801) Port 6 */ 122 #define SEALEVEL_2801_7_PID 0X2871 /* SeaLINK+8/232 (2801) Port 7 */ 123 #define SEALEVEL_2801_8_PID 0X2881 /* SeaLINK+8/232 (2801) Port 8 */ 124 #define SEALEVEL_2802_1_PID 0X2812 /* SeaLINK+8/485 (2802) Port 1 */ 125 #define SEALEVEL_2802_2_PID 0X2822 /* SeaLINK+8/485 (2802) Port 2 */ 126 #define SEALEVEL_2802_3_PID 0X2832 /* SeaLINK+8/485 (2802) Port 3 */ 127 #define SEALEVEL_2802_4_PID 0X2842 /* SeaLINK+8/485 (2802) Port 4 */ 128 #define SEALEVEL_2802_5_PID 0X2852 /* SeaLINK+8/485 (2802) Port 5 */ 129 #define SEALEVEL_2802_6_PID 0X2862 /* SeaLINK+8/485 (2802) Port 6 */ 130 #define SEALEVEL_2802_7_PID 0X2872 /* SeaLINK+8/485 (2802) Port 7 */ 131 #define SEALEVEL_2802_8_PID 0X2882 /* SeaLINK+8/485 (2802) Port 8 */ 132 #define SEALEVEL_2803_1_PID 0X2813 /* SeaLINK+8 (2803) Port 1 */ 133 #define SEALEVEL_2803_2_PID 0X2823 /* SeaLINK+8 (2803) Port 2 */ 134 #define SEALEVEL_2803_3_PID 0X2833 /* SeaLINK+8 (2803) Port 3 */ 135 #define SEALEVEL_2803_4_PID 0X2843 /* SeaLINK+8 (2803) Port 4 */ 136 #define SEALEVEL_2803_5_PID 0X2853 /* SeaLINK+8 (2803) Port 5 */ 137 #define SEALEVEL_2803_6_PID 0X2863 /* SeaLINK+8 (2803) Port 6 */ 138 #define SEALEVEL_2803_7_PID 0X2873 /* SeaLINK+8 (2803) Port 7 */ 139 #define SEALEVEL_2803_8_PID 0X2883 /* SeaLINK+8 (2803) Port 8 */ 140 141 /* 142 * The following are the values for two KOBIL chipcard terminals. 143 */ 144 #define KOBIL_VID 0x0d46 /* KOBIL Vendor ID */ 145 #define KOBIL_CONV_B1_PID 0x2020 /* KOBIL Konverter for B1 */ 146 #define KOBIL_CONV_KAAN_PID 0x2021 /* KOBIL_Konverter for KAAN */ 147 148 /* 149 * Icom ID-1 digital transceiver 150 */ 151 152 #define ICOM_ID1_VID 0x0C26 153 #define ICOM_ID1_PID 0x0004 154 155 /* 156 * DSS-20 Sync Station for Sony Ericsson P800 157 */ 158 159 #define FTDI_DSS20_PID 0xFC82 160 161 /* 162 * Home Electronics (www.home-electro.com) USB gadgets 163 */ 164 #define FTDI_HE_TIRA1_PID 0xFA78 /* Tira-1 IR transceiver */ 165 166 /* USB-UIRT - An infrared receiver and transmitter using the 8U232AM chip */ 167 /* http://home.earthlink.net/~jrhees/USBUIRT/index.htm */ 168 #define FTDI_USB_UIRT_PID 0xF850 /* Product Id */ 169 170 /* 171 * ELV USB devices submitted by Christian Abt of ELV (www.elv.de). 172 * All of these devices use FTDI's vendor ID (0x0403). 173 * 174 * The previously included PID for the UO 100 module was incorrect. 175 * In fact, that PID was for ELV's UR 100 USB-RS232 converter (0xFB58). 176 * 177 * Armin Laeuger originally sent the PID for the UM 100 module. 178 */ 179 #define FTDI_ELV_UR100_PID 0xFB58 /* USB-RS232-Umsetzer (UR 100) */ 180 #define FTDI_ELV_UM100_PID 0xFB5A /* USB-Modul UM 100 */ 181 #define FTDI_ELV_UO100_PID 0xFB5B /* USB-Modul UO 100 */ 182 #define FTDI_ELV_ALC8500_PID 0xF06E /* ALC 8500 Expert */ 183 /* Additional ELV PIDs that default to using the FTDI D2XX drivers on 184 * MS Windows, rather than the FTDI Virtual Com Port drivers. 185 * Maybe these will be easier to use with the libftdi/libusb user-space 186 * drivers, or possibly the Comedi drivers in some cases. */ 187 #define FTDI_ELV_CLI7000_PID 0xFB59 /* Computer-Light-Interface (CLI 7000) */ 188 #define FTDI_ELV_PPS7330_PID 0xFB5C /* Processor-Power-Supply (PPS 7330) */ 189 #define FTDI_ELV_TFM100_PID 0xFB5D /* Temperartur-Feuchte Messgeraet (TFM 100) */ 190 #define FTDI_ELV_UDF77_PID 0xFB5E /* USB DCF Funkurh (UDF 77) */ 191 #define FTDI_ELV_UIO88_PID 0xFB5F /* USB-I/O Interface (UIO 88) */ 192 #define FTDI_ELV_UAD8_PID 0xF068 /* USB-AD-Wandler (UAD 8) */ 193 #define FTDI_ELV_UDA7_PID 0xF069 /* USB-DA-Wandler (UDA 7) */ 194 #define FTDI_ELV_USI2_PID 0xF06A /* USB-Schrittmotoren-Interface (USI 2) */ 195 #define FTDI_ELV_T1100_PID 0xF06B /* Thermometer (T 1100) */ 196 #define FTDI_ELV_PCD200_PID 0xF06C /* PC-Datenlogger (PCD 200) */ 197 #define FTDI_ELV_ULA200_PID 0xF06D /* USB-LCD-Ansteuerung (ULA 200) */ 198 #define FTDI_ELV_FHZ1000PC_PID 0xF06F /* FHZ 1000 PC */ 199 #define FTDI_ELV_CSI8_PID 0xE0F0 /* Computer-Schalt-Interface (CSI 8) */ 200 #define FTDI_ELV_EM1000DL_PID 0xE0F1 /* PC-Datenlogger fuer Energiemonitor (EM 1000 DL) */ 201 #define FTDI_ELV_PCK100_PID 0xE0F2 /* PC-Kabeltester (PCK 100) */ 202 #define FTDI_ELV_RFP500_PID 0xE0F3 /* HF-Leistungsmesser (RFP 500) */ 203 #define FTDI_ELV_FS20SIG_PID 0xE0F4 /* Signalgeber (FS 20 SIG) */ 204 #define FTDI_ELV_WS300PC_PID 0xE0F6 /* PC-Wetterstation (WS 300 PC) */ 205 #define FTDI_ELV_FHZ1300PC_PID 0xE0E8 /* FHZ 1300 PC */ 206 #define FTDI_ELV_WS500_PID 0xE0E9 /* PC-Wetterstation (WS 500) */ 207 208 /* 209 * Definitions for ID TECH (www.idt-net.com) devices 210 */ 211 #define IDTECH_VID 0x0ACD /* ID TECH Vendor ID */ 212 #define IDTECH_IDT1221U_PID 0x0300 /* IDT1221U USB to RS-232 adapter */ 213 214 /* 215 * Definitions for Omnidirectional Control Technology, Inc. devices 216 */ 217 #define OCT_VID 0x0B39 /* OCT vendor ID */ 218 /* Note: OCT US101 is also rebadged as Dick Smith Electronics (NZ) XH6381 */ 219 /* Also rebadged as Dick Smith Electronics (Aus) XH6451 */ 220 /* Also rebadged as SIIG Inc. model US2308 hardware version 1 */ 221 #define OCT_US101_PID 0x0421 /* OCT US101 USB to RS-232 */ 222 223 /* an infrared receiver for user access control with IR tags */ 224 #define FTDI_PIEGROUP_PID 0xF208 /* Product Id */ 225 226 /* 227 * Definitions for Artemis astronomical USB based cameras 228 * Check it at http://www.artemisccd.co.uk/ 229 */ 230 #define FTDI_ARTEMIS_PID 0xDF28 /* All Artemis Cameras */ 231 232 /* 233 * Definitions for ATIK Instruments astronomical USB based cameras 234 * Check it at http://www.atik-instruments.com/ 235 */ 236 #define FTDI_ATIK_ATK16_PID 0xDF30 /* ATIK ATK-16 Grayscale Camera */ 237 #define FTDI_ATIK_ATK16C_PID 0xDF32 /* ATIK ATK-16C Colour Camera */ 238 #define FTDI_ATIK_ATK16HR_PID 0xDF31 /* ATIK ATK-16HR Grayscale Camera */ 239 #define FTDI_ATIK_ATK16HRC_PID 0xDF33 /* ATIK ATK-16HRC Colour Camera */ 240 241 /* 242 * Protego product ids 243 */ 244 #define PROTEGO_SPECIAL_1 0xFC70 /* special/unknown device */ 245 #define PROTEGO_R2X0 0xFC71 /* R200-USB TRNG unit (R210, R220, and R230) */ 246 #define PROTEGO_SPECIAL_3 0xFC72 /* special/unknown device */ 247 #define PROTEGO_SPECIAL_4 0xFC73 /* special/unknown device */ 248 249 /* 250 * Gude Analog- und Digitalsysteme GmbH 251 */ 252 #define FTDI_GUDEADS_E808_PID 0xE808 253 #define FTDI_GUDEADS_E809_PID 0xE809 254 #define FTDI_GUDEADS_E80A_PID 0xE80A 255 #define FTDI_GUDEADS_E80B_PID 0xE80B 256 #define FTDI_GUDEADS_E80C_PID 0xE80C 257 #define FTDI_GUDEADS_E80D_PID 0xE80D 258 #define FTDI_GUDEADS_E80E_PID 0xE80E 259 #define FTDI_GUDEADS_E80F_PID 0xE80F 260 #define FTDI_GUDEADS_E888_PID 0xE888 /* Expert ISDN Control USB */ 261 #define FTDI_GUDEADS_E889_PID 0xE889 /* USB RS-232 OptoBridge */ 262 #define FTDI_GUDEADS_E88A_PID 0xE88A 263 #define FTDI_GUDEADS_E88B_PID 0xE88B 264 #define FTDI_GUDEADS_E88C_PID 0xE88C 265 #define FTDI_GUDEADS_E88D_PID 0xE88D 266 #define FTDI_GUDEADS_E88E_PID 0xE88E 267 #define FTDI_GUDEADS_E88F_PID 0xE88F 268 269 /* 270 * Linx Technologies product ids 271 */ 272 #define LINX_SDMUSBQSS_PID 0xF448 /* Linx SDM-USB-QS-S */ 273 #define LINX_MASTERDEVEL2_PID 0xF449 /* Linx Master Development 2.0 */ 274 #define LINX_FUTURE_0_PID 0xF44A /* Linx future device */ 275 #define LINX_FUTURE_1_PID 0xF44B /* Linx future device */ 276 #define LINX_FUTURE_2_PID 0xF44C /* Linx future device */ 277 278 /* CCS Inc. ICDU/ICDU40 product ID - the FT232BM is used in an in-circuit-debugger */ 279 /* unit for PIC16's/PIC18's */ 280 #define FTDI_CCSICDU20_0_PID 0xF9D0 281 #define FTDI_CCSICDU40_1_PID 0xF9D1 282 283 /* Inside Accesso contactless reader (http://www.insidefr.com) */ 284 #define INSIDE_ACCESSO 0xFAD0 285 286 /* 287 * Intrepid Control Systems (http://www.intrepidcs.com/) ValueCAN and NeoVI 288 */ 289 #define INTREPID_VID 0x093C 290 #define INTREPID_VALUECAN_PID 0x0601 291 #define INTREPID_NEOVI_PID 0x0701 292 293 /* 294 * Falcom Wireless Communications GmbH 295 */ 296 #define FALCOM_VID 0x0F94 /* Vendor Id */ 297 #define FALCOM_TWIST_PID 0x0001 /* Falcom Twist USB GPRS modem */ 298 #define FALCOM_SAMBA_PID 0x0005 /* Falcom Samba USB GPRS modem */ 299 300 /* 301 * SUUNTO product ids 302 */ 303 #define FTDI_SUUNTO_SPORTS_PID 0xF680 /* Suunto Sports instrument */ 304 305 /* 306 * Definitions for B&B Electronics products. 307 */ 308 #define BANDB_VID 0x0856 /* B&B Electronics Vendor ID */ 309 #define BANDB_USOTL4_PID 0xAC01 /* USOTL4 Isolated RS-485 Converter */ 310 #define BANDB_USTL4_PID 0xAC02 /* USTL4 RS-485 Converter */ 311 #define BANDB_USO9ML2_PID 0xAC03 /* USO9ML2 Isolated RS-232 Converter */ 312 313 /* 314 * RM Michaelides CANview USB (http://www.rmcan.com) 315 * CAN fieldbus interface adapter, added by port GmbH www.port.de) 316 * Ian Abbott changed the macro names for consistency. 317 */ 318 #define FTDI_RM_CANVIEW_PID 0xfd60 /* Product Id */ 319 320 /* 321 * EVER Eco Pro UPS (http://www.ever.com.pl/) 322 */ 323 324 #define EVER_ECO_PRO_CDS 0xe520 /* RS-232 converter */ 325 326 /* 327 * 4N-GALAXY.DE PIDs for CAN-USB, USB-RS232, USB-RS422, USB-RS485, 328 * USB-TTY activ, USB-TTY passiv. Some PIDs are used by several devices 329 * and I'm not entirely sure which are used by which. 330 */ 331 #define FTDI_4N_GALAXY_DE_0_PID 0x8372 332 #define FTDI_4N_GALAXY_DE_1_PID 0xF3C0 333 #define FTDI_4N_GALAXY_DE_2_PID 0xF3C1 334 335 /* 336 * Mobility Electronics products. 337 */ 338 #define MOBILITY_VID 0x1342 339 #define MOBILITY_USB_SERIAL_PID 0x0202 /* EasiDock USB 200 serial */ 340 341 /* 342 * microHAM product IDs (http://www.microham.com). 343 * Submitted by Justin Burket (KL1RL) <zorton@jtan.com> 344 * and Mike Studer (K6EEP) <k6eep@hamsoftware.org>. 345 * Ian Abbott <abbotti@mev.co.uk> added a few more from the driver INF file. 346 */ 347 #define FTDI_MHAM_KW_PID 0xEEE8 /* USB-KW interface */ 348 #define FTDI_MHAM_YS_PID 0xEEE9 /* USB-YS interface */ 349 #define FTDI_MHAM_Y6_PID 0xEEEA /* USB-Y6 interface */ 350 #define FTDI_MHAM_Y8_PID 0xEEEB /* USB-Y8 interface */ 351 #define FTDI_MHAM_IC_PID 0xEEEC /* USB-IC interface */ 352 #define FTDI_MHAM_DB9_PID 0xEEED /* USB-DB9 interface */ 353 #define FTDI_MHAM_RS232_PID 0xEEEE /* USB-RS232 interface */ 354 #define FTDI_MHAM_Y9_PID 0xEEEF /* USB-Y9 interface */ 355 356 /* 357 * Active Robots product ids. 358 */ 359 #define FTDI_ACTIVE_ROBOTS_PID 0xE548 /* USB comms board */ 360 361 /* 362 * Xsens Technologies BV products (http://www.xsens.com). 363 */ 364 #define XSENS_CONVERTER_0_PID 0xD388 365 #define XSENS_CONVERTER_1_PID 0xD389 366 #define XSENS_CONVERTER_2_PID 0xD38A 367 #define XSENS_CONVERTER_3_PID 0xD38B 368 #define XSENS_CONVERTER_4_PID 0xD38C 369 #define XSENS_CONVERTER_5_PID 0xD38D 370 #define XSENS_CONVERTER_6_PID 0xD38E 371 #define XSENS_CONVERTER_7_PID 0xD38F 372 373 /* 374 * Teratronik product ids. 375 * Submitted by O. W�lfelschneider. 376 */ 377 #define FTDI_TERATRONIK_VCP_PID 0xEC88 /* Teratronik device (preferring VCP driver on windows) */ 378 #define FTDI_TERATRONIK_D2XX_PID 0xEC89 /* Teratronik device (preferring D2XX driver on windows) */ 379 380 /* 381 * Evolution Robotics products (http://www.evolution.com/). 382 * Submitted by Shawn M. Lavelle. 383 */ 384 #define EVOLUTION_VID 0xDEEE /* Vendor ID */ 385 #define EVOLUTION_ER1_PID 0x0300 /* ER1 Control Module */ 386 387 /* Pyramid Computer GmbH */ 388 #define FTDI_PYRAMID_PID 0xE6C8 /* Pyramid Appliance Display */ 389 390 /* 391 * Posiflex inc retail equipment (http://www.posiflex.com.tw) 392 */ 393 #define POSIFLEX_VID 0x0d3a /* Vendor ID */ 394 #define POSIFLEX_PP7000_PID 0x0300 /* PP-7000II thermal printer */ 395 396 /* 397 * Westrex International devices submitted by Cory Lee 398 */ 399 #define FTDI_WESTREX_MODEL_777_PID 0xDC00 /* Model 777 */ 400 #define FTDI_WESTREX_MODEL_8900F_PID 0xDC01 /* Model 8900F */ 401 402 /* Commands */ 403 #define FTDI_SIO_RESET 0 /* Reset the port */ 404 #define FTDI_SIO_MODEM_CTRL 1 /* Set the modem control register */ 405 #define FTDI_SIO_SET_FLOW_CTRL 2 /* Set flow control register */ 406 #define FTDI_SIO_SET_BAUD_RATE 3 /* Set baud rate */ 407 #define FTDI_SIO_SET_DATA 4 /* Set the data characteristics of the port */ 408 #define FTDI_SIO_GET_MODEM_STATUS 5 /* Retrieve current value of modern status register */ 409 #define FTDI_SIO_SET_EVENT_CHAR 6 /* Set the event character */ 410 #define FTDI_SIO_SET_ERROR_CHAR 7 /* Set the error character */ 411 #define FTDI_SIO_SET_LATENCY_TIMER 9 /* Set the latency timer */ 412 #define FTDI_SIO_GET_LATENCY_TIMER 10 /* Get the latency timer */ 413 414 415 /* 416 * BmRequestType: 1100 0000b 417 * bRequest: FTDI_E2_READ 418 * wValue: 0 419 * wIndex: Address of word to read 420 * wLength: 2 421 * Data: Will return a word of data from E2Address 422 * 423 */ 424 425 /* Port Identifier Table */ 426 #define PIT_DEFAULT 0 /* SIOA */ 427 #define PIT_SIOA 1 /* SIOA */ 428 /* The device this driver is tested with one has only one port */ 429 #define PIT_SIOB 2 /* SIOB */ 430 #define PIT_PARALLEL 3 /* Parallel */ 431 432 /* FTDI_SIO_RESET */ 433 #define FTDI_SIO_RESET_REQUEST FTDI_SIO_RESET 434 #define FTDI_SIO_RESET_REQUEST_TYPE 0x40 435 #define FTDI_SIO_RESET_SIO 0 436 #define FTDI_SIO_RESET_PURGE_RX 1 437 #define FTDI_SIO_RESET_PURGE_TX 2 438 439 /* 440 * BmRequestType: 0100 0000B 441 * bRequest: FTDI_SIO_RESET 442 * wValue: Control Value 443 * 0 = Reset SIO 444 * 1 = Purge RX buffer 445 * 2 = Purge TX buffer 446 * wIndex: Port 447 * wLength: 0 448 * Data: None 449 * 450 * The Reset SIO command has this effect: 451 * 452 * Sets flow control set to 'none' 453 * Event char = $0D 454 * Event trigger = disabled 455 * Purge RX buffer 456 * Purge TX buffer 457 * Clear DTR 458 * Clear RTS 459 * baud and data format not reset 460 * 461 * The Purge RX and TX buffer commands affect nothing except the buffers 462 * 463 */ 464 465 /* FTDI_SIO_SET_BAUDRATE */ 466 #define FTDI_SIO_SET_BAUDRATE_REQUEST_TYPE 0x40 467 #define FTDI_SIO_SET_BAUDRATE_REQUEST 3 468 469 /* 470 * BmRequestType: 0100 0000B 471 * bRequest: FTDI_SIO_SET_BAUDRATE 472 * wValue: BaudDivisor value - see below 473 * wIndex: Port 474 * wLength: 0 475 * Data: None 476 * The BaudDivisor values are calculated as follows: 477 * - BaseClock is either 12000000 or 48000000 depending on the device. FIXME: I wish 478 * I knew how to detect old chips to select proper base clock! 479 * - BaudDivisor is a fixed point number encoded in a funny way. 480 * (--WRONG WAY OF THINKING--) 481 * BaudDivisor is a fixed point number encoded with following bit weighs: 482 * (-2)(-1)(13..0). It is a radical with a denominator of 4, so values 483 * end with 0.0 (00...), 0.25 (10...), 0.5 (01...), and 0.75 (11...). 484 * (--THE REALITY--) 485 * The both-bits-set has quite different meaning from 0.75 - the chip designers 486 * have decided it to mean 0.125 instead of 0.75. 487 * This info looked up in FTDI application note "FT8U232 DEVICES \ Data Rates 488 * and Flow Control Consideration for USB to RS232". 489 * - BaudDivisor = (BaseClock / 16) / BaudRate, where the (=) operation should 490 * automagically re-encode the resulting value to take fractions into consideration. 491 * As all values are integers, some bit twiddling is in order: 492 * BaudDivisor = (BaseClock / 16 / BaudRate) | 493 * (((BaseClock / 2 / BaudRate) & 4) ? 0x4000 // 0.5 494 * : ((BaseClock / 2 / BaudRate) & 2) ? 0x8000 // 0.25 495 * : ((BaseClock / 2 / BaudRate) & 1) ? 0xc000 // 0.125 496 * : 0) 497 * 498 * For the FT232BM, a 17th divisor bit was introduced to encode the multiples 499 * of 0.125 missing from the FT8U232AM. Bits 16 to 14 are coded as follows 500 * (the first four codes are the same as for the FT8U232AM, where bit 16 is 501 * always 0): 502 * 000 - add .000 to divisor 503 * 001 - add .500 to divisor 504 * 010 - add .250 to divisor 505 * 011 - add .125 to divisor 506 * 100 - add .375 to divisor 507 * 101 - add .625 to divisor 508 * 110 - add .750 to divisor 509 * 111 - add .875 to divisor 510 * Bits 15 to 0 of the 17-bit divisor are placed in the urb value. Bit 16 is 511 * placed in bit 0 of the urb index. 512 * 513 * Note that there are a couple of special cases to support the highest baud 514 * rates. If the calculated divisor value is 1, this needs to be replaced with 515 * 0. Additionally for the FT232BM, if the calculated divisor value is 0x4001 516 * (1.5), this needs to be replaced with 0x0001 (1) (but this divisor value is 517 * not supported by the FT8U232AM). 518 */ 519 520 typedef enum { 521 SIO = 1, 522 FT8U232AM = 2, 523 FT232BM = 3, 524 FT2232C = 4, 525 } ftdi_chip_type_t; 526 527 typedef enum { 528 ftdi_sio_b300 = 0, 529 ftdi_sio_b600 = 1, 530 ftdi_sio_b1200 = 2, 531 ftdi_sio_b2400 = 3, 532 ftdi_sio_b4800 = 4, 533 ftdi_sio_b9600 = 5, 534 ftdi_sio_b19200 = 6, 535 ftdi_sio_b38400 = 7, 536 ftdi_sio_b57600 = 8, 537 ftdi_sio_b115200 = 9 538 } FTDI_SIO_baudrate_t ; 539 540 /* 541 * The ftdi_8U232AM_xxMHz_byyy constants have been removed. The encoded divisor values 542 * are calculated internally. 543 */ 544 545 #define FTDI_SIO_SET_DATA_REQUEST FTDI_SIO_SET_DATA 546 #define FTDI_SIO_SET_DATA_REQUEST_TYPE 0x40 547 #define FTDI_SIO_SET_DATA_PARITY_NONE (0x0 << 8 ) 548 #define FTDI_SIO_SET_DATA_PARITY_ODD (0x1 << 8 ) 549 #define FTDI_SIO_SET_DATA_PARITY_EVEN (0x2 << 8 ) 550 #define FTDI_SIO_SET_DATA_PARITY_MARK (0x3 << 8 ) 551 #define FTDI_SIO_SET_DATA_PARITY_SPACE (0x4 << 8 ) 552 #define FTDI_SIO_SET_DATA_STOP_BITS_1 (0x0 << 11 ) 553 #define FTDI_SIO_SET_DATA_STOP_BITS_15 (0x1 << 11 ) 554 #define FTDI_SIO_SET_DATA_STOP_BITS_2 (0x2 << 11 ) 555 #define FTDI_SIO_SET_BREAK (0x1 << 14) 556 /* FTDI_SIO_SET_DATA */ 557 558 /* 559 * BmRequestType: 0100 0000B 560 * bRequest: FTDI_SIO_SET_DATA 561 * wValue: Data characteristics (see below) 562 * wIndex: Port 563 * wLength: 0 564 * Data: No 565 * 566 * Data characteristics 567 * 568 * B0..7 Number of data bits 569 * B8..10 Parity 570 * 0 = None 571 * 1 = Odd 572 * 2 = Even 573 * 3 = Mark 574 * 4 = Space 575 * B11..13 Stop Bits 576 * 0 = 1 577 * 1 = 1.5 578 * 2 = 2 579 * B14 580 * 1 = TX ON (break) 581 * 0 = TX OFF (normal state) 582 * B15 Reserved 583 * 584 */ 585 586 587 588 /* FTDI_SIO_MODEM_CTRL */ 589 #define FTDI_SIO_SET_MODEM_CTRL_REQUEST_TYPE 0x40 590 #define FTDI_SIO_SET_MODEM_CTRL_REQUEST FTDI_SIO_MODEM_CTRL 591 592 /* 593 * BmRequestType: 0100 0000B 594 * bRequest: FTDI_SIO_MODEM_CTRL 595 * wValue: ControlValue (see below) 596 * wIndex: Port 597 * wLength: 0 598 * Data: None 599 * 600 * NOTE: If the device is in RTS/CTS flow control, the RTS set by this 601 * command will be IGNORED without an error being returned 602 * Also - you can not set DTR and RTS with one control message 603 */ 604 605 #define FTDI_SIO_SET_DTR_MASK 0x1 606 #define FTDI_SIO_SET_DTR_HIGH ( 1 | ( FTDI_SIO_SET_DTR_MASK << 8)) 607 #define FTDI_SIO_SET_DTR_LOW ( 0 | ( FTDI_SIO_SET_DTR_MASK << 8)) 608 #define FTDI_SIO_SET_RTS_MASK 0x2 609 #define FTDI_SIO_SET_RTS_HIGH ( 2 | ( FTDI_SIO_SET_RTS_MASK << 8 )) 610 #define FTDI_SIO_SET_RTS_LOW ( 0 | ( FTDI_SIO_SET_RTS_MASK << 8 )) 611 612 /* 613 * ControlValue 614 * B0 DTR state 615 * 0 = reset 616 * 1 = set 617 * B1 RTS state 618 * 0 = reset 619 * 1 = set 620 * B2..7 Reserved 621 * B8 DTR state enable 622 * 0 = ignore 623 * 1 = use DTR state 624 * B9 RTS state enable 625 * 0 = ignore 626 * 1 = use RTS state 627 * B10..15 Reserved 628 */ 629 630 /* FTDI_SIO_SET_FLOW_CTRL */ 631 #define FTDI_SIO_SET_FLOW_CTRL_REQUEST_TYPE 0x40 632 #define FTDI_SIO_SET_FLOW_CTRL_REQUEST FTDI_SIO_SET_FLOW_CTRL 633 #define FTDI_SIO_DISABLE_FLOW_CTRL 0x0 634 #define FTDI_SIO_RTS_CTS_HS (0x1 << 8) 635 #define FTDI_SIO_DTR_DSR_HS (0x2 << 8) 636 #define FTDI_SIO_XON_XOFF_HS (0x4 << 8) 637 /* 638 * BmRequestType: 0100 0000b 639 * bRequest: FTDI_SIO_SET_FLOW_CTRL 640 * wValue: Xoff/Xon 641 * wIndex: Protocol/Port - hIndex is protocl / lIndex is port 642 * wLength: 0 643 * Data: None 644 * 645 * hIndex protocol is: 646 * B0 Output handshaking using RTS/CTS 647 * 0 = disabled 648 * 1 = enabled 649 * B1 Output handshaking using DTR/DSR 650 * 0 = disabled 651 * 1 = enabled 652 * B2 Xon/Xoff handshaking 653 * 0 = disabled 654 * 1 = enabled 655 * 656 * A value of zero in the hIndex field disables handshaking 657 * 658 * If Xon/Xoff handshaking is specified, the hValue field should contain the XOFF character 659 * and the lValue field contains the XON character. 660 */ 661 662 /* 663 * FTDI_SIO_GET_LATENCY_TIMER 664 * 665 * Set the timeout interval. The FTDI collects data from the slave 666 * device, transmitting it to the host when either A) 62 bytes are 667 * received, or B) the timeout interval has elapsed and the buffer 668 * contains at least 1 byte. Setting this value to a small number 669 * can dramatically improve performance for applications which send 670 * small packets, since the default value is 16ms. 671 */ 672 #define FTDI_SIO_GET_LATENCY_TIMER_REQUEST FTDI_SIO_GET_LATENCY_TIMER 673 #define FTDI_SIO_GET_LATENCY_TIMER_REQUEST_TYPE 0xC0 674 675 /* 676 * BmRequestType: 1100 0000b 677 * bRequest: FTDI_SIO_GET_LATENCY_TIMER 678 * wValue: 0 679 * wIndex: Port 680 * wLength: 0 681 * Data: latency (on return) 682 */ 683 684 /* 685 * FTDI_SIO_SET_LATENCY_TIMER 686 * 687 * Set the timeout interval. The FTDI collects data from the slave 688 * device, transmitting it to the host when either A) 62 bytes are 689 * received, or B) the timeout interval has elapsed and the buffer 690 * contains at least 1 byte. Setting this value to a small number 691 * can dramatically improve performance for applications which send 692 * small packets, since the default value is 16ms. 693 */ 694 #define FTDI_SIO_SET_LATENCY_TIMER_REQUEST FTDI_SIO_SET_LATENCY_TIMER 695 #define FTDI_SIO_SET_LATENCY_TIMER_REQUEST_TYPE 0x40 696 697 /* 698 * BmRequestType: 0100 0000b 699 * bRequest: FTDI_SIO_SET_LATENCY_TIMER 700 * wValue: Latency (milliseconds) 701 * wIndex: Port 702 * wLength: 0 703 * Data: None 704 * 705 * wValue: 706 * B0..7 Latency timer 707 * B8..15 0 708 * 709 */ 710 711 /* 712 * FTDI_SIO_SET_EVENT_CHAR 713 * 714 * Set the special event character for the specified communications port. 715 * If the device sees this character it will immediately return the 716 * data read so far - rather than wait 40ms or until 62 bytes are read 717 * which is what normally happens. 718 */ 719 720 721 #define FTDI_SIO_SET_EVENT_CHAR_REQUEST FTDI_SIO_SET_EVENT_CHAR 722 #define FTDI_SIO_SET_EVENT_CHAR_REQUEST_TYPE 0x40 723 724 725 /* 726 * BmRequestType: 0100 0000b 727 * bRequest: FTDI_SIO_SET_EVENT_CHAR 728 * wValue: EventChar 729 * wIndex: Port 730 * wLength: 0 731 * Data: None 732 * 733 * wValue: 734 * B0..7 Event Character 735 * B8 Event Character Processing 736 * 0 = disabled 737 * 1 = enabled 738 * B9..15 Reserved 739 * 740 */ 741 742 /* FTDI_SIO_SET_ERROR_CHAR */ 743 744 /* Set the parity error replacement character for the specified communications port */ 745 746 /* 747 * BmRequestType: 0100 0000b 748 * bRequest: FTDI_SIO_SET_EVENT_CHAR 749 * wValue: Error Char 750 * wIndex: Port 751 * wLength: 0 752 * Data: None 753 * 754 *Error Char 755 * B0..7 Error Character 756 * B8 Error Character Processing 757 * 0 = disabled 758 * 1 = enabled 759 * B9..15 Reserved 760 * 761 */ 762 763 /* FTDI_SIO_GET_MODEM_STATUS */ 764 /* Retrieve the current value of the modem status register */ 765 766 #define FTDI_SIO_GET_MODEM_STATUS_REQUEST_TYPE 0xc0 767 #define FTDI_SIO_GET_MODEM_STATUS_REQUEST FTDI_SIO_GET_MODEM_STATUS 768 #define FTDI_SIO_CTS_MASK 0x10 769 #define FTDI_SIO_DSR_MASK 0x20 770 #define FTDI_SIO_RI_MASK 0x40 771 #define FTDI_SIO_RLSD_MASK 0x80 772 /* 773 * BmRequestType: 1100 0000b 774 * bRequest: FTDI_SIO_GET_MODEM_STATUS 775 * wValue: zero 776 * wIndex: Port 777 * wLength: 1 778 * Data: Status 779 * 780 * One byte of data is returned 781 * B0..3 0 782 * B4 CTS 783 * 0 = inactive 784 * 1 = active 785 * B5 DSR 786 * 0 = inactive 787 * 1 = active 788 * B6 Ring Indicator (RI) 789 * 0 = inactive 790 * 1 = active 791 * B7 Receive Line Signal Detect (RLSD) 792 * 0 = inactive 793 * 1 = active 794 */ 795 796 797 798 /* Descriptors returned by the device 799 * 800 * Device Descriptor 801 * 802 * Offset Field Size Value Description 803 * 0 bLength 1 0x12 Size of descriptor in bytes 804 * 1 bDescriptorType 1 0x01 DEVICE Descriptor Type 805 * 2 bcdUSB 2 0x0110 USB Spec Release Number 806 * 4 bDeviceClass 1 0x00 Class Code 807 * 5 bDeviceSubClass 1 0x00 SubClass Code 808 * 6 bDeviceProtocol 1 0x00 Protocol Code 809 * 7 bMaxPacketSize0 1 0x08 Maximum packet size for endpoint 0 810 * 8 idVendor 2 0x0403 Vendor ID 811 * 10 idProduct 2 0x8372 Product ID (FTDI_SIO_PID) 812 * 12 bcdDevice 2 0x0001 Device release number 813 * 14 iManufacturer 1 0x01 Index of man. string desc 814 * 15 iProduct 1 0x02 Index of prod string desc 815 * 16 iSerialNumber 1 0x02 Index of serial nmr string desc 816 * 17 bNumConfigurations 1 0x01 Number of possible configurations 817 * 818 * Configuration Descriptor 819 * 820 * Offset Field Size Value 821 * 0 bLength 1 0x09 Size of descriptor in bytes 822 * 1 bDescriptorType 1 0x02 CONFIGURATION Descriptor Type 823 * 2 wTotalLength 2 0x0020 Total length of data 824 * 4 bNumInterfaces 1 0x01 Number of interfaces supported 825 * 5 bConfigurationValue 1 0x01 Argument for SetCOnfiguration() req 826 * 6 iConfiguration 1 0x02 Index of config string descriptor 827 * 7 bmAttributes 1 0x20 Config characteristics Remote Wakeup 828 * 8 MaxPower 1 0x1E Max power consumption 829 * 830 * Interface Descriptor 831 * 832 * Offset Field Size Value 833 * 0 bLength 1 0x09 Size of descriptor in bytes 834 * 1 bDescriptorType 1 0x04 INTERFACE Descriptor Type 835 * 2 bInterfaceNumber 1 0x00 Number of interface 836 * 3 bAlternateSetting 1 0x00 Value used to select alternate 837 * 4 bNumEndpoints 1 0x02 Number of endpoints 838 * 5 bInterfaceClass 1 0xFF Class Code 839 * 6 bInterfaceSubClass 1 0xFF Subclass Code 840 * 7 bInterfaceProtocol 1 0xFF Protocol Code 841 * 8 iInterface 1 0x02 Index of interface string description 842 * 843 * IN Endpoint Descriptor 844 * 845 * Offset Field Size Value 846 * 0 bLength 1 0x07 Size of descriptor in bytes 847 * 1 bDescriptorType 1 0x05 ENDPOINT descriptor type 848 * 2 bEndpointAddress 1 0x82 Address of endpoint 849 * 3 bmAttributes 1 0x02 Endpoint attributes - Bulk 850 * 4 bNumEndpoints 2 0x0040 maximum packet size 851 * 5 bInterval 1 0x00 Interval for polling endpoint 852 * 853 * OUT Endpoint Descriptor 854 * 855 * Offset Field Size Value 856 * 0 bLength 1 0x07 Size of descriptor in bytes 857 * 1 bDescriptorType 1 0x05 ENDPOINT descriptor type 858 * 2 bEndpointAddress 1 0x02 Address of endpoint 859 * 3 bmAttributes 1 0x02 Endpoint attributes - Bulk 860 * 4 bNumEndpoints 2 0x0040 maximum packet size 861 * 5 bInterval 1 0x00 Interval for polling endpoint 862 * 863 * DATA FORMAT 864 * 865 * IN Endpoint 866 * 867 * The device reserves the first two bytes of data on this endpoint to contain the current 868 * values of the modem and line status registers. In the absence of data, the device 869 * generates a message consisting of these two status bytes every 40 ms 870 * 871 * Byte 0: Modem Status 872 * 873 * Offset Description 874 * B0 Reserved - must be 1 875 * B1 Reserved - must be 0 876 * B2 Reserved - must be 0 877 * B3 Reserved - must be 0 878 * B4 Clear to Send (CTS) 879 * B5 Data Set Ready (DSR) 880 * B6 Ring Indicator (RI) 881 * B7 Receive Line Signal Detect (RLSD) 882 * 883 * Byte 1: Line Status 884 * 885 * Offset Description 886 * B0 Data Ready (DR) 887 * B1 Overrun Error (OE) 888 * B2 Parity Error (PE) 889 * B3 Framing Error (FE) 890 * B4 Break Interrupt (BI) 891 * B5 Transmitter Holding Register (THRE) 892 * B6 Transmitter Empty (TEMT) 893 * B7 Error in RCVR FIFO 894 * 895 */ 896 #define FTDI_RS0_CTS (1 << 4) 897 #define FTDI_RS0_DSR (1 << 5) 898 #define FTDI_RS0_RI (1 << 6) 899 #define FTDI_RS0_RLSD (1 << 7) 900 901 #define FTDI_RS_DR 1 902 #define FTDI_RS_OE (1<<1) 903 #define FTDI_RS_PE (1<<2) 904 #define FTDI_RS_FE (1<<3) 905 #define FTDI_RS_BI (1<<4) 906 #define FTDI_RS_THRE (1<<5) 907 #define FTDI_RS_TEMT (1<<6) 908 #define FTDI_RS_FIFO (1<<7) 909 910 /* 911 * OUT Endpoint 912 * 913 * This device reserves the first bytes of data on this endpoint contain the length 914 * and port identifier of the message. For the FTDI USB Serial converter the port 915 * identifier is always 1. 916 * 917 * Byte 0: Line Status 918 * 919 * Offset Description 920 * B0 Reserved - must be 1 921 * B1 Reserved - must be 0 922 * B2..7 Length of message - (not including Byte 0) 923 * 924 */ 925 926