1 /* 2 * Digi AccelePort USB-4 and USB-2 Serial Converters 3 * 4 * Copyright 2000 by Digi International 5 * 6 * This program is free software; you can redistribute it and/or modify 7 * it under the terms of the GNU General Public License as published by 8 * the Free Software Foundation; either version 2 of the License, or 9 * (at your option) any later version. 10 * 11 * Shamelessly based on Brian Warner's keyspan_pda.c and Greg Kroah-Hartman's 12 * usb-serial driver. 13 * 14 * Peter Berger (pberger@brimson.com) 15 * Al Borchers (borchers@steinerpoint.com) 16 * 17 * (12/03/2001) gkh 18 * switched to using port->open_count instead of private version. 19 * Removed port->active 20 * 21 * (04/08/2001) gb 22 * Identify version on module load. 23 * 24 * (11/01/2000) Adam J. Richter 25 * usb_device_id table support 26 * 27 * (11/01/2000) pberger and borchers 28 * -- Turned off the USB_DISABLE_SPD flag for write bulk urbs--it caused 29 * USB 4 ports to hang on startup. 30 * -- Serialized access to write urbs by adding the dp_write_urb_in_use 31 * flag; otherwise, the driver caused SMP system hangs. Watching the 32 * urb status is not sufficient. 33 * 34 * (10/05/2000) gkh 35 * -- Fixed bug with urb->dev not being set properly, now that the usb 36 * core needs it. 37 * 38 * (8/8/2000) pberger and borchers 39 * -- Fixed close so that 40 * - it can timeout while waiting for transmit idle, if needed; 41 * - it ignores interrupts when flushing the port, turning 42 * of modem signalling, and so on; 43 * - it waits for the flush to really complete before returning. 44 * -- Read_bulk_callback and write_bulk_callback check for a closed 45 * port before using the tty struct or writing to the port. 46 * -- The two changes above fix the oops caused by interrupted closes. 47 * -- Added interruptible args to write_oob_command and set_modem_signals 48 * and added a timeout arg to transmit_idle; needed for fixes to 49 * close. 50 * -- Added code for rx_throttle and rx_unthrottle so that input flow 51 * control works. 52 * -- Added code to set overrun, parity, framing, and break errors 53 * (untested). 54 * -- Set USB_DISABLE_SPD flag for write bulk urbs, so no 0 length 55 * bulk writes are done. These hung the Digi USB device. The 56 * 0 length bulk writes were a new feature of usb-uhci added in 57 * the 2.4.0-test6 kernels. 58 * -- Fixed mod inc race in open; do mod inc before sleeping to wait 59 * for a close to finish. 60 * 61 * (7/31/2000) pberger 62 * -- Fixed bugs with hardware handshaking: 63 * - Added code to set/clear tty->hw_stopped in digi_read_oob_callback() 64 * and digi_set_termios() 65 * -- Added code in digi_set_termios() to 66 * - add conditional in code handling transition from B0 to only 67 * set RTS if RTS/CTS flow control is either not in use or if 68 * the port is not currently throttled. 69 * - handle turning off CRTSCTS. 70 * 71 * (7/30/2000) borchers 72 * -- Added support for more than one Digi USB device by moving 73 * globals to a private structure in the pointed to from the 74 * usb_serial structure. 75 * -- Moved the modem change and transmit idle wait queues into 76 * the port private structure, so each port has its own queue 77 * rather than sharing global queues. 78 * -- Added support for break signals. 79 * 80 * (7/25/2000) pberger 81 * -- Added USB-2 support. Note: the USB-2 supports 3 devices: two 82 * serial and a parallel port. The parallel port is implemented 83 * as a serial-to-parallel converter. That is, the driver actually 84 * presents all three USB-2 interfaces as serial ports, but the third 85 * one physically connects to a parallel device. Thus, for example, 86 * one could plug a parallel printer into the USB-2's third port, 87 * but from the kernel's (and userland's) point of view what's 88 * actually out there is a serial device. 89 * 90 * (7/15/2000) borchers 91 * -- Fixed race in open when a close is in progress. 92 * -- Keep count of opens and dec the module use count for each 93 * outstanding open when shutdown is called (on disconnect). 94 * -- Fixed sanity checks in read_bulk_callback and write_bulk_callback 95 * so pointers are checked before use. 96 * -- Split read bulk callback into in band and out of band 97 * callbacks, and no longer restart read chains if there is 98 * a status error or a sanity error. This fixed the seg 99 * faults and other errors we used to get on disconnect. 100 * -- Port->active is once again a flag as usb-serial intended it 101 * to be, not a count. Since it was only a char it would 102 * have been limited to 256 simultaneous opens. Now the open 103 * count is kept in the port private structure in dp_open_count. 104 * -- Added code for modularization of the digi_acceleport driver. 105 * 106 * (6/27/2000) pberger and borchers 107 * -- Zeroed out sync field in the wakeup_task before first use; 108 * otherwise the uninitialized value might prevent the task from 109 * being scheduled. 110 * -- Initialized ret value to 0 in write_bulk_callback, otherwise 111 * the uninitialized value could cause a spurious debugging message. 112 * 113 * (6/22/2000) pberger and borchers 114 * -- Made cond_wait_... inline--apparently on SPARC the flags arg 115 * to spin_lock_irqsave cannot be passed to another function 116 * to call spin_unlock_irqrestore. Thanks to Pauline Middelink. 117 * -- In digi_set_modem_signals the inner nested spin locks use just 118 * spin_lock() rather than spin_lock_irqsave(). The old code 119 * mistakenly left interrupts off. Thanks to Pauline Middelink. 120 * -- copy_from_user (which can sleep) is no longer called while a 121 * spinlock is held. We copy to a local buffer before getting 122 * the spinlock--don't like the extra copy but the code is simpler. 123 * -- Printk and dbg are no longer called while a spin lock is held. 124 * 125 * (6/4/2000) pberger and borchers 126 * -- Replaced separate calls to spin_unlock_irqrestore and 127 * interruptible_sleep_on_timeout with a new function 128 * cond_wait_interruptible_timeout_irqrestore. This eliminates 129 * the race condition where the wake up could happen after 130 * the unlock and before the sleep. 131 * -- Close now waits for output to drain. 132 * -- Open waits until any close in progress is finished. 133 * -- All out of band responses are now processed, not just the 134 * first in a USB packet. 135 * -- Fixed a bug that prevented the driver from working when the 136 * first Digi port was not the first USB serial port--the driver 137 * was mistakenly using the external USB serial port number to 138 * try to index into its internal ports. 139 * -- Fixed an SMP bug -- write_bulk_callback is called directly from 140 * an interrupt, so spin_lock_irqsave/spin_unlock_irqrestore are 141 * needed for locks outside write_bulk_callback that are also 142 * acquired by write_bulk_callback to prevent deadlocks. 143 * -- Fixed support for select() by making digi_chars_in_buffer() 144 * return 256 when -EINPROGRESS is set, as the line discipline 145 * code in n_tty.c expects. 146 * -- Fixed an include file ordering problem that prevented debugging 147 * messages from working. 148 * -- Fixed an intermittent timeout problem that caused writes to 149 * sometimes get stuck on some machines on some kernels. It turns 150 * out in these circumstances write_chan() (in n_tty.c) was 151 * asleep waiting for our wakeup call. Even though we call 152 * wake_up_interruptible() in digi_write_bulk_callback(), there is 153 * a race condition that could cause the wakeup to fail: if our 154 * wake_up_interruptible() call occurs between the time that our 155 * driver write routine finishes and write_chan() sets current->state 156 * to TASK_INTERRUPTIBLE, the effect of our wakeup setting the state 157 * to TASK_RUNNING will be lost and write_chan's subsequent call to 158 * schedule() will never return (unless it catches a signal). 159 * This race condition occurs because write_bulk_callback() (and thus 160 * the wakeup) are called asynchonously from an interrupt, rather than 161 * from the scheduler. We can avoid the race by calling the wakeup 162 * from the scheduler queue and that's our fix: Now, at the end of 163 * write_bulk_callback() we queue up a wakeup call on the scheduler 164 * task queue. We still also invoke the wakeup directly since that 165 * squeezes a bit more performance out of the driver, and any lost 166 * race conditions will get cleaned up at the next scheduler run. 167 * 168 * NOTE: The problem also goes away if you comment out 169 * the two code lines in write_chan() where current->state 170 * is set to TASK_RUNNING just before calling driver.write() and to 171 * TASK_INTERRUPTIBLE immediately afterwards. This is why the 172 * problem did not show up with the 2.2 kernels -- they do not 173 * include that code. 174 * 175 * (5/16/2000) pberger and borchers 176 * -- Added timeouts to sleeps, to defend against lost wake ups. 177 * -- Handle transition to/from B0 baud rate in digi_set_termios. 178 * 179 * (5/13/2000) pberger and borchers 180 * -- All commands now sent on out of band port, using 181 * digi_write_oob_command. 182 * -- Get modem control signals whenever they change, support TIOCMGET/ 183 * SET/BIS/BIC ioctls. 184 * -- digi_set_termios now supports parity, word size, stop bits, and 185 * receive enable. 186 * -- Cleaned up open and close, use digi_set_termios and 187 * digi_write_oob_command to set port parameters. 188 * -- Added digi_startup_device to start read chains on all ports. 189 * -- Write buffer is only used when count==1, to be sure put_char can 190 * write a char (unless the buffer is full). 191 * 192 * (5/10/2000) pberger and borchers 193 * -- Added MOD_INC_USE_COUNT/MOD_DEC_USE_COUNT calls on open/close. 194 * -- Fixed problem where the first incoming character is lost on 195 * port opens after the first close on that port. Now we keep 196 * the read_urb chain open until shutdown. 197 * -- Added more port conditioning calls in digi_open and digi_close. 198 * -- Convert port->active to a use count so that we can deal with multiple 199 * opens and closes properly. 200 * -- Fixed some problems with the locking code. 201 * 202 * (5/3/2000) pberger and borchers 203 * -- First alpha version of the driver--many known limitations and bugs. 204 * 205 * 206 * Locking and SMP 207 * 208 * - Each port, including the out-of-band port, has a lock used to 209 * serialize all access to the port's private structure. 210 * - The port lock is also used to serialize all writes and access to 211 * the port's URB. 212 * - The port lock is also used for the port write_wait condition 213 * variable. Holding the port lock will prevent a wake up on the 214 * port's write_wait; this can be used with cond_wait_... to be sure 215 * the wake up is not lost in a race when dropping the lock and 216 * sleeping waiting for the wakeup. 217 * - digi_write() does not sleep, since it is sometimes called on 218 * interrupt time. 219 * - digi_write_bulk_callback() and digi_read_bulk_callback() are 220 * called directly from interrupts. Hence spin_lock_irqsave() 221 * and spin_unlock_irqrestore() are used in the rest of the code 222 * for any locks they acquire. 223 * - digi_write_bulk_callback() gets the port lock before waking up 224 * processes sleeping on the port write_wait. It also schedules 225 * wake ups so they happen from the scheduler, because the tty 226 * system can miss wake ups from interrupts. 227 * - All sleeps use a timeout of DIGI_RETRY_TIMEOUT before looping to 228 * recheck the condition they are sleeping on. This is defensive, 229 * in case a wake up is lost. 230 * - Following Documentation/DocBook/kernel-locking.pdf no spin locks 231 * are held when calling copy_to/from_user or printk. 232 * 233 * $Id: digi_acceleport.c,v 1.80.1.2 2000/11/02 05:45:08 root Exp $ 234 */ 235 236 #include <linux/config.h> 237 #include <linux/kernel.h> 238 #include <linux/errno.h> 239 #include <linux/init.h> 240 #include <linux/slab.h> 241 #include <linux/tty.h> 242 #include <linux/tty_driver.h> 243 #include <linux/tty_flip.h> 244 #include <linux/module.h> 245 #include <linux/spinlock.h> 246 #include <linux/workqueue.h> 247 #include <asm/uaccess.h> 248 #include <linux/usb.h> 249 #include <linux/wait.h> 250 #include "usb-serial.h" 251 252 /* Defines */ 253 254 /* 255 * Version Information 256 */ 257 #define DRIVER_VERSION "v1.80.1.2" 258 #define DRIVER_AUTHOR "Peter Berger <pberger@brimson.com>, Al Borchers <borchers@steinerpoint.com>" 259 #define DRIVER_DESC "Digi AccelePort USB-2/USB-4 Serial Converter driver" 260 261 /* port output buffer length -- must be <= transfer buffer length - 2 */ 262 /* so we can be sure to send the full buffer in one urb */ 263 #define DIGI_OUT_BUF_SIZE 8 264 265 /* port input buffer length -- must be >= transfer buffer length - 3 */ 266 /* so we can be sure to hold at least one full buffer from one urb */ 267 #define DIGI_IN_BUF_SIZE 64 268 269 /* retry timeout while sleeping */ 270 #define DIGI_RETRY_TIMEOUT (HZ/10) 271 272 /* timeout while waiting for tty output to drain in close */ 273 /* this delay is used twice in close, so the total delay could */ 274 /* be twice this value */ 275 #define DIGI_CLOSE_TIMEOUT (5*HZ) 276 277 278 /* AccelePort USB Defines */ 279 280 /* ids */ 281 #define DIGI_VENDOR_ID 0x05c5 282 #define DIGI_2_ID 0x0002 /* USB-2 */ 283 #define DIGI_4_ID 0x0004 /* USB-4 */ 284 285 /* commands 286 * "INB": can be used on the in-band endpoint 287 * "OOB": can be used on the out-of-band endpoint 288 */ 289 #define DIGI_CMD_SET_BAUD_RATE 0 /* INB, OOB */ 290 #define DIGI_CMD_SET_WORD_SIZE 1 /* INB, OOB */ 291 #define DIGI_CMD_SET_PARITY 2 /* INB, OOB */ 292 #define DIGI_CMD_SET_STOP_BITS 3 /* INB, OOB */ 293 #define DIGI_CMD_SET_INPUT_FLOW_CONTROL 4 /* INB, OOB */ 294 #define DIGI_CMD_SET_OUTPUT_FLOW_CONTROL 5 /* INB, OOB */ 295 #define DIGI_CMD_SET_DTR_SIGNAL 6 /* INB, OOB */ 296 #define DIGI_CMD_SET_RTS_SIGNAL 7 /* INB, OOB */ 297 #define DIGI_CMD_READ_INPUT_SIGNALS 8 /* OOB */ 298 #define DIGI_CMD_IFLUSH_FIFO 9 /* OOB */ 299 #define DIGI_CMD_RECEIVE_ENABLE 10 /* INB, OOB */ 300 #define DIGI_CMD_BREAK_CONTROL 11 /* INB, OOB */ 301 #define DIGI_CMD_LOCAL_LOOPBACK 12 /* INB, OOB */ 302 #define DIGI_CMD_TRANSMIT_IDLE 13 /* INB, OOB */ 303 #define DIGI_CMD_READ_UART_REGISTER 14 /* OOB */ 304 #define DIGI_CMD_WRITE_UART_REGISTER 15 /* INB, OOB */ 305 #define DIGI_CMD_AND_UART_REGISTER 16 /* INB, OOB */ 306 #define DIGI_CMD_OR_UART_REGISTER 17 /* INB, OOB */ 307 #define DIGI_CMD_SEND_DATA 18 /* INB */ 308 #define DIGI_CMD_RECEIVE_DATA 19 /* INB */ 309 #define DIGI_CMD_RECEIVE_DISABLE 20 /* INB */ 310 #define DIGI_CMD_GET_PORT_TYPE 21 /* OOB */ 311 312 /* baud rates */ 313 #define DIGI_BAUD_50 0 314 #define DIGI_BAUD_75 1 315 #define DIGI_BAUD_110 2 316 #define DIGI_BAUD_150 3 317 #define DIGI_BAUD_200 4 318 #define DIGI_BAUD_300 5 319 #define DIGI_BAUD_600 6 320 #define DIGI_BAUD_1200 7 321 #define DIGI_BAUD_1800 8 322 #define DIGI_BAUD_2400 9 323 #define DIGI_BAUD_4800 10 324 #define DIGI_BAUD_7200 11 325 #define DIGI_BAUD_9600 12 326 #define DIGI_BAUD_14400 13 327 #define DIGI_BAUD_19200 14 328 #define DIGI_BAUD_28800 15 329 #define DIGI_BAUD_38400 16 330 #define DIGI_BAUD_57600 17 331 #define DIGI_BAUD_76800 18 332 #define DIGI_BAUD_115200 19 333 #define DIGI_BAUD_153600 20 334 #define DIGI_BAUD_230400 21 335 #define DIGI_BAUD_460800 22 336 337 /* arguments */ 338 #define DIGI_WORD_SIZE_5 0 339 #define DIGI_WORD_SIZE_6 1 340 #define DIGI_WORD_SIZE_7 2 341 #define DIGI_WORD_SIZE_8 3 342 343 #define DIGI_PARITY_NONE 0 344 #define DIGI_PARITY_ODD 1 345 #define DIGI_PARITY_EVEN 2 346 #define DIGI_PARITY_MARK 3 347 #define DIGI_PARITY_SPACE 4 348 349 #define DIGI_STOP_BITS_1 0 350 #define DIGI_STOP_BITS_2 1 351 352 #define DIGI_INPUT_FLOW_CONTROL_XON_XOFF 1 353 #define DIGI_INPUT_FLOW_CONTROL_RTS 2 354 #define DIGI_INPUT_FLOW_CONTROL_DTR 4 355 356 #define DIGI_OUTPUT_FLOW_CONTROL_XON_XOFF 1 357 #define DIGI_OUTPUT_FLOW_CONTROL_CTS 2 358 #define DIGI_OUTPUT_FLOW_CONTROL_DSR 4 359 360 #define DIGI_DTR_INACTIVE 0 361 #define DIGI_DTR_ACTIVE 1 362 #define DIGI_DTR_INPUT_FLOW_CONTROL 2 363 364 #define DIGI_RTS_INACTIVE 0 365 #define DIGI_RTS_ACTIVE 1 366 #define DIGI_RTS_INPUT_FLOW_CONTROL 2 367 #define DIGI_RTS_TOGGLE 3 368 369 #define DIGI_FLUSH_TX 1 370 #define DIGI_FLUSH_RX 2 371 #define DIGI_RESUME_TX 4 /* clears xoff condition */ 372 373 #define DIGI_TRANSMIT_NOT_IDLE 0 374 #define DIGI_TRANSMIT_IDLE 1 375 376 #define DIGI_DISABLE 0 377 #define DIGI_ENABLE 1 378 379 #define DIGI_DEASSERT 0 380 #define DIGI_ASSERT 1 381 382 /* in band status codes */ 383 #define DIGI_OVERRUN_ERROR 4 384 #define DIGI_PARITY_ERROR 8 385 #define DIGI_FRAMING_ERROR 16 386 #define DIGI_BREAK_ERROR 32 387 388 /* out of band status */ 389 #define DIGI_NO_ERROR 0 390 #define DIGI_BAD_FIRST_PARAMETER 1 391 #define DIGI_BAD_SECOND_PARAMETER 2 392 #define DIGI_INVALID_LINE 3 393 #define DIGI_INVALID_OPCODE 4 394 395 /* input signals */ 396 #define DIGI_READ_INPUT_SIGNALS_SLOT 1 397 #define DIGI_READ_INPUT_SIGNALS_ERR 2 398 #define DIGI_READ_INPUT_SIGNALS_BUSY 4 399 #define DIGI_READ_INPUT_SIGNALS_PE 8 400 #define DIGI_READ_INPUT_SIGNALS_CTS 16 401 #define DIGI_READ_INPUT_SIGNALS_DSR 32 402 #define DIGI_READ_INPUT_SIGNALS_RI 64 403 #define DIGI_READ_INPUT_SIGNALS_DCD 128 404 405 406 /* Structures */ 407 408 struct digi_serial { 409 spinlock_t ds_serial_lock; 410 struct usb_serial_port *ds_oob_port; /* out-of-band port */ 411 int ds_oob_port_num; /* index of out-of-band port */ 412 int ds_device_started; 413 }; 414 415 struct digi_port { 416 spinlock_t dp_port_lock; 417 int dp_port_num; 418 int dp_out_buf_len; 419 unsigned char dp_out_buf[DIGI_OUT_BUF_SIZE]; 420 int dp_in_buf_len; 421 unsigned char dp_in_buf[DIGI_IN_BUF_SIZE]; 422 unsigned char dp_in_flag_buf[DIGI_IN_BUF_SIZE]; 423 int dp_write_urb_in_use; 424 unsigned int dp_modem_signals; 425 wait_queue_head_t dp_modem_change_wait; 426 int dp_transmit_idle; 427 wait_queue_head_t dp_transmit_idle_wait; 428 int dp_throttled; 429 int dp_throttle_restart; 430 wait_queue_head_t dp_flush_wait; 431 int dp_in_close; /* close in progress */ 432 wait_queue_head_t dp_close_wait; /* wait queue for close */ 433 struct work_struct dp_wakeup_work; 434 }; 435 436 437 /* Local Function Declarations */ 438 439 static void digi_wakeup_write( struct usb_serial_port *port ); 440 static void digi_wakeup_write_lock(void *); 441 static int digi_write_oob_command( struct usb_serial_port *port, 442 unsigned char *buf, int count, int interruptible ); 443 static int digi_write_inb_command( struct usb_serial_port *port, 444 unsigned char *buf, int count, unsigned long timeout ); 445 static int digi_set_modem_signals( struct usb_serial_port *port, 446 unsigned int modem_signals, int interruptible ); 447 static int digi_transmit_idle( struct usb_serial_port *port, 448 unsigned long timeout ); 449 static void digi_rx_throttle (struct usb_serial_port *port); 450 static void digi_rx_unthrottle (struct usb_serial_port *port); 451 static void digi_set_termios( struct usb_serial_port *port, 452 struct termios *old_termios ); 453 static void digi_break_ctl( struct usb_serial_port *port, int break_state ); 454 static int digi_ioctl( struct usb_serial_port *port, struct file *file, 455 unsigned int cmd, unsigned long arg ); 456 static int digi_tiocmget( struct usb_serial_port *port, struct file *file ); 457 static int digi_tiocmset( struct usb_serial_port *port, struct file *file, 458 unsigned int set, unsigned int clear ); 459 static int digi_write( struct usb_serial_port *port, const unsigned char *buf, int count ); 460 static void digi_write_bulk_callback( struct urb *urb, struct pt_regs *regs ); 461 static int digi_write_room( struct usb_serial_port *port ); 462 static int digi_chars_in_buffer( struct usb_serial_port *port ); 463 static int digi_open( struct usb_serial_port *port, struct file *filp ); 464 static void digi_close( struct usb_serial_port *port, struct file *filp ); 465 static int digi_startup_device( struct usb_serial *serial ); 466 static int digi_startup( struct usb_serial *serial ); 467 static void digi_shutdown( struct usb_serial *serial ); 468 static void digi_read_bulk_callback( struct urb *urb, struct pt_regs *regs ); 469 static int digi_read_inb_callback( struct urb *urb ); 470 static int digi_read_oob_callback( struct urb *urb ); 471 472 473 /* Statics */ 474 475 static int debug; 476 477 static struct usb_device_id id_table_combined [] = { 478 { USB_DEVICE(DIGI_VENDOR_ID, DIGI_2_ID) }, 479 { USB_DEVICE(DIGI_VENDOR_ID, DIGI_4_ID) }, 480 { } /* Terminating entry */ 481 }; 482 483 static struct usb_device_id id_table_2 [] = { 484 { USB_DEVICE(DIGI_VENDOR_ID, DIGI_2_ID) }, 485 { } /* Terminating entry */ 486 }; 487 488 static struct usb_device_id id_table_4 [] = { 489 { USB_DEVICE(DIGI_VENDOR_ID, DIGI_4_ID) }, 490 { } /* Terminating entry */ 491 }; 492 493 MODULE_DEVICE_TABLE (usb, id_table_combined); 494 495 static struct usb_driver digi_driver = { 496 .name = "digi_acceleport", 497 .probe = usb_serial_probe, 498 .disconnect = usb_serial_disconnect, 499 .id_table = id_table_combined, 500 .no_dynamic_id = 1, 501 }; 502 503 504 /* device info needed for the Digi serial converter */ 505 506 static struct usb_serial_driver digi_acceleport_2_device = { 507 .driver = { 508 .owner = THIS_MODULE, 509 .name = "digi_2", 510 }, 511 .description = "Digi 2 port USB adapter", 512 .id_table = id_table_2, 513 .num_interrupt_in = 0, 514 .num_bulk_in = 4, 515 .num_bulk_out = 4, 516 .num_ports = 3, 517 .open = digi_open, 518 .close = digi_close, 519 .write = digi_write, 520 .write_room = digi_write_room, 521 .write_bulk_callback = digi_write_bulk_callback, 522 .read_bulk_callback = digi_read_bulk_callback, 523 .chars_in_buffer = digi_chars_in_buffer, 524 .throttle = digi_rx_throttle, 525 .unthrottle = digi_rx_unthrottle, 526 .ioctl = digi_ioctl, 527 .set_termios = digi_set_termios, 528 .break_ctl = digi_break_ctl, 529 .tiocmget = digi_tiocmget, 530 .tiocmset = digi_tiocmset, 531 .attach = digi_startup, 532 .shutdown = digi_shutdown, 533 }; 534 535 static struct usb_serial_driver digi_acceleport_4_device = { 536 .driver = { 537 .owner = THIS_MODULE, 538 .name = "digi_4", 539 }, 540 .description = "Digi 4 port USB adapter", 541 .id_table = id_table_4, 542 .num_interrupt_in = 0, 543 .num_bulk_in = 5, 544 .num_bulk_out = 5, 545 .num_ports = 4, 546 .open = digi_open, 547 .close = digi_close, 548 .write = digi_write, 549 .write_room = digi_write_room, 550 .write_bulk_callback = digi_write_bulk_callback, 551 .read_bulk_callback = digi_read_bulk_callback, 552 .chars_in_buffer = digi_chars_in_buffer, 553 .throttle = digi_rx_throttle, 554 .unthrottle = digi_rx_unthrottle, 555 .ioctl = digi_ioctl, 556 .set_termios = digi_set_termios, 557 .break_ctl = digi_break_ctl, 558 .tiocmget = digi_tiocmget, 559 .tiocmset = digi_tiocmset, 560 .attach = digi_startup, 561 .shutdown = digi_shutdown, 562 }; 563 564 565 /* Functions */ 566 567 /* 568 * Cond Wait Interruptible Timeout Irqrestore 569 * 570 * Do spin_unlock_irqrestore and interruptible_sleep_on_timeout 571 * so that wake ups are not lost if they occur between the unlock 572 * and the sleep. In other words, spin_unlock_irqrestore and 573 * interruptible_sleep_on_timeout are "atomic" with respect to 574 * wake ups. This is used to implement condition variables. 575 * 576 * interruptible_sleep_on_timeout is deprecated and has been replaced 577 * with the equivalent code. 578 */ 579 580 static inline long cond_wait_interruptible_timeout_irqrestore( 581 wait_queue_head_t *q, long timeout, 582 spinlock_t *lock, unsigned long flags ) 583 { 584 DEFINE_WAIT(wait); 585 586 prepare_to_wait(q, &wait, TASK_INTERRUPTIBLE); 587 spin_unlock_irqrestore(lock, flags); 588 timeout = schedule_timeout(timeout); 589 finish_wait(q, &wait); 590 591 return timeout; 592 } 593 594 595 /* 596 * Digi Wakeup Write 597 * 598 * Wake up port, line discipline, and tty processes sleeping 599 * on writes. 600 */ 601 602 static void digi_wakeup_write_lock(void *arg) 603 { 604 struct usb_serial_port *port = arg; 605 unsigned long flags; 606 struct digi_port *priv = usb_get_serial_port_data(port); 607 608 609 spin_lock_irqsave( &priv->dp_port_lock, flags ); 610 digi_wakeup_write( port ); 611 spin_unlock_irqrestore( &priv->dp_port_lock, flags ); 612 } 613 614 static void digi_wakeup_write( struct usb_serial_port *port ) 615 { 616 617 struct tty_struct *tty = port->tty; 618 619 620 /* wake up port processes */ 621 wake_up_interruptible( &port->write_wait ); 622 623 /* wake up line discipline */ 624 tty_wakeup(tty); 625 } 626 627 628 /* 629 * Digi Write OOB Command 630 * 631 * Write commands on the out of band port. Commands are 4 632 * bytes each, multiple commands can be sent at once, and 633 * no command will be split across USB packets. Returns 0 634 * if successful, -EINTR if interrupted while sleeping and 635 * the interruptible flag is true, or a negative error 636 * returned by usb_submit_urb. 637 */ 638 639 static int digi_write_oob_command( struct usb_serial_port *port, 640 unsigned char *buf, int count, int interruptible ) 641 { 642 643 int ret = 0; 644 int len; 645 struct usb_serial_port *oob_port = (struct usb_serial_port *)((struct digi_serial *)(usb_get_serial_data(port->serial)))->ds_oob_port; 646 struct digi_port *oob_priv = usb_get_serial_port_data(oob_port); 647 unsigned long flags = 0; 648 649 650 dbg( "digi_write_oob_command: TOP: port=%d, count=%d", oob_priv->dp_port_num, count ); 651 652 spin_lock_irqsave( &oob_priv->dp_port_lock, flags ); 653 654 while( count > 0 ) { 655 656 while( oob_port->write_urb->status == -EINPROGRESS 657 || oob_priv->dp_write_urb_in_use ) { 658 cond_wait_interruptible_timeout_irqrestore( 659 &oob_port->write_wait, DIGI_RETRY_TIMEOUT, 660 &oob_priv->dp_port_lock, flags ); 661 if( interruptible && signal_pending(current) ) { 662 return( -EINTR ); 663 } 664 spin_lock_irqsave( &oob_priv->dp_port_lock, flags ); 665 } 666 667 /* len must be a multiple of 4, so commands are not split */ 668 len = min(count, oob_port->bulk_out_size ); 669 if( len > 4 ) 670 len &= ~3; 671 672 memcpy( oob_port->write_urb->transfer_buffer, buf, len ); 673 oob_port->write_urb->transfer_buffer_length = len; 674 oob_port->write_urb->dev = port->serial->dev; 675 676 if( (ret=usb_submit_urb(oob_port->write_urb, GFP_ATOMIC)) == 0 ) { 677 oob_priv->dp_write_urb_in_use = 1; 678 count -= len; 679 buf += len; 680 } 681 682 } 683 684 spin_unlock_irqrestore( &oob_priv->dp_port_lock, flags ); 685 686 if( ret ) { 687 err("%s: usb_submit_urb failed, ret=%d", __FUNCTION__, 688 ret ); 689 } 690 691 return( ret ); 692 693 } 694 695 696 /* 697 * Digi Write In Band Command 698 * 699 * Write commands on the given port. Commands are 4 700 * bytes each, multiple commands can be sent at once, and 701 * no command will be split across USB packets. If timeout 702 * is non-zero, write in band command will return after 703 * waiting unsuccessfully for the URB status to clear for 704 * timeout ticks. Returns 0 if successful, or a negative 705 * error returned by digi_write. 706 */ 707 708 static int digi_write_inb_command( struct usb_serial_port *port, 709 unsigned char *buf, int count, unsigned long timeout ) 710 { 711 712 int ret = 0; 713 int len; 714 struct digi_port *priv = usb_get_serial_port_data(port); 715 unsigned char *data = port->write_urb->transfer_buffer; 716 unsigned long flags = 0; 717 718 719 dbg( "digi_write_inb_command: TOP: port=%d, count=%d", priv->dp_port_num, 720 count ); 721 722 if( timeout ) 723 timeout += jiffies; 724 else 725 timeout = ULONG_MAX; 726 727 spin_lock_irqsave( &priv->dp_port_lock, flags ); 728 729 while( count > 0 && ret == 0 ) { 730 731 while( (port->write_urb->status == -EINPROGRESS 732 || priv->dp_write_urb_in_use) && time_before(jiffies, timeout)) { 733 cond_wait_interruptible_timeout_irqrestore( 734 &port->write_wait, DIGI_RETRY_TIMEOUT, 735 &priv->dp_port_lock, flags ); 736 if( signal_pending(current) ) { 737 return( -EINTR ); 738 } 739 spin_lock_irqsave( &priv->dp_port_lock, flags ); 740 } 741 742 /* len must be a multiple of 4 and small enough to */ 743 /* guarantee the write will send buffered data first, */ 744 /* so commands are in order with data and not split */ 745 len = min(count, port->bulk_out_size-2-priv->dp_out_buf_len ); 746 if( len > 4 ) 747 len &= ~3; 748 749 /* write any buffered data first */ 750 if( priv->dp_out_buf_len > 0 ) { 751 data[0] = DIGI_CMD_SEND_DATA; 752 data[1] = priv->dp_out_buf_len; 753 memcpy( data+2, priv->dp_out_buf, 754 priv->dp_out_buf_len ); 755 memcpy( data+2+priv->dp_out_buf_len, buf, len ); 756 port->write_urb->transfer_buffer_length 757 = priv->dp_out_buf_len+2+len; 758 } else { 759 memcpy( data, buf, len ); 760 port->write_urb->transfer_buffer_length = len; 761 } 762 port->write_urb->dev = port->serial->dev; 763 764 if( (ret=usb_submit_urb(port->write_urb, GFP_ATOMIC)) == 0 ) { 765 priv->dp_write_urb_in_use = 1; 766 priv->dp_out_buf_len = 0; 767 count -= len; 768 buf += len; 769 } 770 771 } 772 773 spin_unlock_irqrestore( &priv->dp_port_lock, flags ); 774 775 if( ret ) { 776 err("%s: usb_submit_urb failed, ret=%d, port=%d", __FUNCTION__, 777 ret, priv->dp_port_num ); 778 } 779 780 return( ret ); 781 782 } 783 784 785 /* 786 * Digi Set Modem Signals 787 * 788 * Sets or clears DTR and RTS on the port, according to the 789 * modem_signals argument. Use TIOCM_DTR and TIOCM_RTS flags 790 * for the modem_signals argument. Returns 0 if successful, 791 * -EINTR if interrupted while sleeping, or a non-zero error 792 * returned by usb_submit_urb. 793 */ 794 795 static int digi_set_modem_signals( struct usb_serial_port *port, 796 unsigned int modem_signals, int interruptible ) 797 { 798 799 int ret; 800 struct digi_port *port_priv = usb_get_serial_port_data(port); 801 struct usb_serial_port *oob_port = (struct usb_serial_port *)((struct digi_serial *)(usb_get_serial_data(port->serial)))->ds_oob_port; 802 struct digi_port *oob_priv = usb_get_serial_port_data(oob_port); 803 unsigned char *data = oob_port->write_urb->transfer_buffer; 804 unsigned long flags = 0; 805 806 807 dbg( "digi_set_modem_signals: TOP: port=%d, modem_signals=0x%x", 808 port_priv->dp_port_num, modem_signals ); 809 810 spin_lock_irqsave( &oob_priv->dp_port_lock, flags ); 811 spin_lock( &port_priv->dp_port_lock ); 812 813 while( oob_port->write_urb->status == -EINPROGRESS 814 || oob_priv->dp_write_urb_in_use ) { 815 spin_unlock( &port_priv->dp_port_lock ); 816 cond_wait_interruptible_timeout_irqrestore( 817 &oob_port->write_wait, DIGI_RETRY_TIMEOUT, 818 &oob_priv->dp_port_lock, flags ); 819 if( interruptible && signal_pending(current) ) { 820 return( -EINTR ); 821 } 822 spin_lock_irqsave( &oob_priv->dp_port_lock, flags ); 823 spin_lock( &port_priv->dp_port_lock ); 824 } 825 826 data[0] = DIGI_CMD_SET_DTR_SIGNAL; 827 data[1] = port_priv->dp_port_num; 828 data[2] = (modem_signals&TIOCM_DTR) ? 829 DIGI_DTR_ACTIVE : DIGI_DTR_INACTIVE; 830 data[3] = 0; 831 832 data[4] = DIGI_CMD_SET_RTS_SIGNAL; 833 data[5] = port_priv->dp_port_num; 834 data[6] = (modem_signals&TIOCM_RTS) ? 835 DIGI_RTS_ACTIVE : DIGI_RTS_INACTIVE; 836 data[7] = 0; 837 838 oob_port->write_urb->transfer_buffer_length = 8; 839 oob_port->write_urb->dev = port->serial->dev; 840 841 if( (ret=usb_submit_urb(oob_port->write_urb, GFP_ATOMIC)) == 0 ) { 842 oob_priv->dp_write_urb_in_use = 1; 843 port_priv->dp_modem_signals = 844 (port_priv->dp_modem_signals&~(TIOCM_DTR|TIOCM_RTS)) 845 | (modem_signals&(TIOCM_DTR|TIOCM_RTS)); 846 } 847 848 spin_unlock( &port_priv->dp_port_lock ); 849 spin_unlock_irqrestore( &oob_priv->dp_port_lock, flags ); 850 851 if( ret ) { 852 err("%s: usb_submit_urb failed, ret=%d", __FUNCTION__, 853 ret ); 854 } 855 856 return( ret ); 857 858 } 859 860 861 /* 862 * Digi Transmit Idle 863 * 864 * Digi transmit idle waits, up to timeout ticks, for the transmitter 865 * to go idle. It returns 0 if successful or a negative error. 866 * 867 * There are race conditions here if more than one process is calling 868 * digi_transmit_idle on the same port at the same time. However, this 869 * is only called from close, and only one process can be in close on a 870 * port at a time, so its ok. 871 */ 872 873 static int digi_transmit_idle( struct usb_serial_port *port, 874 unsigned long timeout ) 875 { 876 877 int ret; 878 unsigned char buf[2]; 879 struct digi_port *priv = usb_get_serial_port_data(port); 880 unsigned long flags = 0; 881 882 883 spin_lock_irqsave( &priv->dp_port_lock, flags ); 884 priv->dp_transmit_idle = 0; 885 spin_unlock_irqrestore( &priv->dp_port_lock, flags ); 886 887 buf[0] = DIGI_CMD_TRANSMIT_IDLE; 888 buf[1] = 0; 889 890 timeout += jiffies; 891 892 if( (ret=digi_write_inb_command( port, buf, 2, timeout-jiffies )) != 0 ) 893 return( ret ); 894 895 spin_lock_irqsave( &priv->dp_port_lock, flags ); 896 897 while( time_before(jiffies, timeout) && !priv->dp_transmit_idle ) { 898 cond_wait_interruptible_timeout_irqrestore( 899 &priv->dp_transmit_idle_wait, DIGI_RETRY_TIMEOUT, 900 &priv->dp_port_lock, flags ); 901 if( signal_pending(current) ) { 902 return( -EINTR ); 903 } 904 spin_lock_irqsave( &priv->dp_port_lock, flags ); 905 } 906 907 priv->dp_transmit_idle = 0; 908 spin_unlock_irqrestore( &priv->dp_port_lock, flags ); 909 910 return( 0 ); 911 912 } 913 914 915 static void digi_rx_throttle( struct usb_serial_port *port ) 916 { 917 918 unsigned long flags; 919 struct digi_port *priv = usb_get_serial_port_data(port); 920 921 922 dbg( "digi_rx_throttle: TOP: port=%d", priv->dp_port_num ); 923 924 /* stop receiving characters by not resubmitting the read urb */ 925 spin_lock_irqsave( &priv->dp_port_lock, flags ); 926 priv->dp_throttled = 1; 927 priv->dp_throttle_restart = 0; 928 priv->dp_in_buf_len = 0; 929 spin_unlock_irqrestore( &priv->dp_port_lock, flags ); 930 931 } 932 933 934 static void digi_rx_unthrottle( struct usb_serial_port *port ) 935 { 936 937 int ret = 0; 938 int len; 939 unsigned long flags; 940 struct digi_port *priv = usb_get_serial_port_data(port); 941 struct tty_struct *tty = port->tty; 942 943 944 dbg( "digi_rx_unthrottle: TOP: port=%d", priv->dp_port_num ); 945 946 spin_lock_irqsave( &priv->dp_port_lock, flags ); 947 948 /* send any buffered chars from throttle time on to tty subsystem */ 949 950 len = tty_buffer_request_room(tty, priv->dp_in_buf_len); 951 if( len > 0 ) { 952 tty_insert_flip_string_flags(tty, priv->dp_in_buf, priv->dp_in_flag_buf, len); 953 tty_flip_buffer_push( tty ); 954 } 955 956 /* restart read chain */ 957 if( priv->dp_throttle_restart ) { 958 port->read_urb->dev = port->serial->dev; 959 ret = usb_submit_urb( port->read_urb, GFP_ATOMIC ); 960 } 961 962 /* turn throttle off */ 963 priv->dp_throttled = 0; 964 priv->dp_in_buf_len = 0; 965 priv->dp_throttle_restart = 0; 966 967 spin_unlock_irqrestore( &priv->dp_port_lock, flags ); 968 969 if( ret ) { 970 err("%s: usb_submit_urb failed, ret=%d, port=%d", __FUNCTION__, 971 ret, priv->dp_port_num ); 972 } 973 974 } 975 976 977 static void digi_set_termios( struct usb_serial_port *port, 978 struct termios *old_termios ) 979 { 980 981 struct digi_port *priv = usb_get_serial_port_data(port); 982 unsigned int iflag = port->tty->termios->c_iflag; 983 unsigned int cflag = port->tty->termios->c_cflag; 984 unsigned int old_iflag = old_termios->c_iflag; 985 unsigned int old_cflag = old_termios->c_cflag; 986 unsigned char buf[32]; 987 unsigned int modem_signals; 988 int arg,ret; 989 int i = 0; 990 991 992 dbg( "digi_set_termios: TOP: port=%d, iflag=0x%x, old_iflag=0x%x, cflag=0x%x, old_cflag=0x%x", priv->dp_port_num, iflag, old_iflag, cflag, old_cflag ); 993 994 /* set baud rate */ 995 if( (cflag&CBAUD) != (old_cflag&CBAUD) ) { 996 997 arg = -1; 998 999 /* reassert DTR and (maybe) RTS on transition from B0 */ 1000 if( (old_cflag&CBAUD) == B0 ) { 1001 /* don't set RTS if using hardware flow control */ 1002 /* and throttling input */ 1003 modem_signals = TIOCM_DTR; 1004 if( !(port->tty->termios->c_cflag & CRTSCTS) || 1005 !test_bit(TTY_THROTTLED, &port->tty->flags) ) { 1006 modem_signals |= TIOCM_RTS; 1007 } 1008 digi_set_modem_signals( port, modem_signals, 1 ); 1009 } 1010 1011 switch( (cflag&CBAUD) ) { 1012 /* drop DTR and RTS on transition to B0 */ 1013 case B0: digi_set_modem_signals( port, 0, 1 ); break; 1014 case B50: arg = DIGI_BAUD_50; break; 1015 case B75: arg = DIGI_BAUD_75; break; 1016 case B110: arg = DIGI_BAUD_110; break; 1017 case B150: arg = DIGI_BAUD_150; break; 1018 case B200: arg = DIGI_BAUD_200; break; 1019 case B300: arg = DIGI_BAUD_300; break; 1020 case B600: arg = DIGI_BAUD_600; break; 1021 case B1200: arg = DIGI_BAUD_1200; break; 1022 case B1800: arg = DIGI_BAUD_1800; break; 1023 case B2400: arg = DIGI_BAUD_2400; break; 1024 case B4800: arg = DIGI_BAUD_4800; break; 1025 case B9600: arg = DIGI_BAUD_9600; break; 1026 case B19200: arg = DIGI_BAUD_19200; break; 1027 case B38400: arg = DIGI_BAUD_38400; break; 1028 case B57600: arg = DIGI_BAUD_57600; break; 1029 case B115200: arg = DIGI_BAUD_115200; break; 1030 case B230400: arg = DIGI_BAUD_230400; break; 1031 case B460800: arg = DIGI_BAUD_460800; break; 1032 default: 1033 dbg( "digi_set_termios: can't handle baud rate 0x%x", 1034 (cflag&CBAUD) ); 1035 break; 1036 } 1037 1038 if( arg != -1 ) { 1039 buf[i++] = DIGI_CMD_SET_BAUD_RATE; 1040 buf[i++] = priv->dp_port_num; 1041 buf[i++] = arg; 1042 buf[i++] = 0; 1043 } 1044 1045 } 1046 1047 /* set parity */ 1048 if( (cflag&(PARENB|PARODD)) != (old_cflag&(PARENB|PARODD)) ) { 1049 1050 if( (cflag&PARENB) ) { 1051 if( (cflag&PARODD) ) 1052 arg = DIGI_PARITY_ODD; 1053 else 1054 arg = DIGI_PARITY_EVEN; 1055 } else { 1056 arg = DIGI_PARITY_NONE; 1057 } 1058 1059 buf[i++] = DIGI_CMD_SET_PARITY; 1060 buf[i++] = priv->dp_port_num; 1061 buf[i++] = arg; 1062 buf[i++] = 0; 1063 1064 } 1065 1066 /* set word size */ 1067 if( (cflag&CSIZE) != (old_cflag&CSIZE) ) { 1068 1069 arg = -1; 1070 1071 switch( (cflag&CSIZE) ) { 1072 case CS5: arg = DIGI_WORD_SIZE_5; break; 1073 case CS6: arg = DIGI_WORD_SIZE_6; break; 1074 case CS7: arg = DIGI_WORD_SIZE_7; break; 1075 case CS8: arg = DIGI_WORD_SIZE_8; break; 1076 default: 1077 dbg( "digi_set_termios: can't handle word size %d", 1078 (cflag&CSIZE) ); 1079 break; 1080 } 1081 1082 if( arg != -1 ) { 1083 buf[i++] = DIGI_CMD_SET_WORD_SIZE; 1084 buf[i++] = priv->dp_port_num; 1085 buf[i++] = arg; 1086 buf[i++] = 0; 1087 } 1088 1089 } 1090 1091 /* set stop bits */ 1092 if( (cflag&CSTOPB) != (old_cflag&CSTOPB) ) { 1093 1094 if( (cflag&CSTOPB) ) 1095 arg = DIGI_STOP_BITS_2; 1096 else 1097 arg = DIGI_STOP_BITS_1; 1098 1099 buf[i++] = DIGI_CMD_SET_STOP_BITS; 1100 buf[i++] = priv->dp_port_num; 1101 buf[i++] = arg; 1102 buf[i++] = 0; 1103 1104 } 1105 1106 /* set input flow control */ 1107 if( (iflag&IXOFF) != (old_iflag&IXOFF) 1108 || (cflag&CRTSCTS) != (old_cflag&CRTSCTS) ) { 1109 1110 arg = 0; 1111 1112 if( (iflag&IXOFF) ) 1113 arg |= DIGI_INPUT_FLOW_CONTROL_XON_XOFF; 1114 else 1115 arg &= ~DIGI_INPUT_FLOW_CONTROL_XON_XOFF; 1116 1117 if( (cflag&CRTSCTS) ) { 1118 1119 arg |= DIGI_INPUT_FLOW_CONTROL_RTS; 1120 1121 /* On USB-4 it is necessary to assert RTS prior */ 1122 /* to selecting RTS input flow control. */ 1123 buf[i++] = DIGI_CMD_SET_RTS_SIGNAL; 1124 buf[i++] = priv->dp_port_num; 1125 buf[i++] = DIGI_RTS_ACTIVE; 1126 buf[i++] = 0; 1127 1128 } else { 1129 arg &= ~DIGI_INPUT_FLOW_CONTROL_RTS; 1130 } 1131 1132 buf[i++] = DIGI_CMD_SET_INPUT_FLOW_CONTROL; 1133 buf[i++] = priv->dp_port_num; 1134 buf[i++] = arg; 1135 buf[i++] = 0; 1136 1137 } 1138 1139 /* set output flow control */ 1140 if( (iflag&IXON) != (old_iflag&IXON) 1141 || (cflag&CRTSCTS) != (old_cflag&CRTSCTS) ) { 1142 1143 arg = 0; 1144 1145 if( (iflag&IXON) ) 1146 arg |= DIGI_OUTPUT_FLOW_CONTROL_XON_XOFF; 1147 else 1148 arg &= ~DIGI_OUTPUT_FLOW_CONTROL_XON_XOFF; 1149 1150 if( (cflag&CRTSCTS) ) { 1151 arg |= DIGI_OUTPUT_FLOW_CONTROL_CTS; 1152 } else { 1153 arg &= ~DIGI_OUTPUT_FLOW_CONTROL_CTS; 1154 port->tty->hw_stopped = 0; 1155 } 1156 1157 buf[i++] = DIGI_CMD_SET_OUTPUT_FLOW_CONTROL; 1158 buf[i++] = priv->dp_port_num; 1159 buf[i++] = arg; 1160 buf[i++] = 0; 1161 1162 } 1163 1164 /* set receive enable/disable */ 1165 if( (cflag&CREAD) != (old_cflag&CREAD) ) { 1166 1167 if( (cflag&CREAD) ) 1168 arg = DIGI_ENABLE; 1169 else 1170 arg = DIGI_DISABLE; 1171 1172 buf[i++] = DIGI_CMD_RECEIVE_ENABLE; 1173 buf[i++] = priv->dp_port_num; 1174 buf[i++] = arg; 1175 buf[i++] = 0; 1176 1177 } 1178 1179 if( (ret=digi_write_oob_command( port, buf, i, 1 )) != 0 ) 1180 dbg( "digi_set_termios: write oob failed, ret=%d", ret ); 1181 1182 } 1183 1184 1185 static void digi_break_ctl( struct usb_serial_port *port, int break_state ) 1186 { 1187 1188 unsigned char buf[4]; 1189 1190 1191 buf[0] = DIGI_CMD_BREAK_CONTROL; 1192 buf[1] = 2; /* length */ 1193 buf[2] = break_state ? 1 : 0; 1194 buf[3] = 0; /* pad */ 1195 1196 digi_write_inb_command( port, buf, 4, 0 ); 1197 1198 } 1199 1200 1201 static int digi_tiocmget( struct usb_serial_port *port, struct file *file ) 1202 { 1203 struct digi_port *priv = usb_get_serial_port_data(port); 1204 unsigned int val; 1205 unsigned long flags; 1206 1207 dbg("%s: TOP: port=%d", __FUNCTION__, priv->dp_port_num); 1208 1209 spin_lock_irqsave( &priv->dp_port_lock, flags ); 1210 val = priv->dp_modem_signals; 1211 spin_unlock_irqrestore( &priv->dp_port_lock, flags ); 1212 return val; 1213 } 1214 1215 1216 static int digi_tiocmset( struct usb_serial_port *port, struct file *file, 1217 unsigned int set, unsigned int clear ) 1218 { 1219 struct digi_port *priv = usb_get_serial_port_data(port); 1220 unsigned int val; 1221 unsigned long flags; 1222 1223 dbg("%s: TOP: port=%d", __FUNCTION__, priv->dp_port_num); 1224 1225 spin_lock_irqsave( &priv->dp_port_lock, flags ); 1226 val = (priv->dp_modem_signals & ~clear) | set; 1227 spin_unlock_irqrestore( &priv->dp_port_lock, flags ); 1228 return digi_set_modem_signals( port, val, 1 ); 1229 } 1230 1231 1232 static int digi_ioctl( struct usb_serial_port *port, struct file *file, 1233 unsigned int cmd, unsigned long arg ) 1234 { 1235 1236 struct digi_port *priv = usb_get_serial_port_data(port); 1237 1238 dbg( "digi_ioctl: TOP: port=%d, cmd=0x%x", priv->dp_port_num, cmd ); 1239 1240 switch (cmd) { 1241 1242 case TIOCMIWAIT: 1243 /* wait for any of the 4 modem inputs (DCD,RI,DSR,CTS)*/ 1244 /* TODO */ 1245 return( 0 ); 1246 1247 case TIOCGICOUNT: 1248 /* return count of modemline transitions */ 1249 /* TODO */ 1250 return 0; 1251 1252 } 1253 1254 return( -ENOIOCTLCMD ); 1255 1256 } 1257 1258 1259 static int digi_write( struct usb_serial_port *port, const unsigned char *buf, int count ) 1260 { 1261 1262 int ret,data_len,new_len; 1263 struct digi_port *priv = usb_get_serial_port_data(port); 1264 unsigned char *data = port->write_urb->transfer_buffer; 1265 unsigned long flags = 0; 1266 1267 1268 dbg( "digi_write: TOP: port=%d, count=%d, in_interrupt=%ld", 1269 priv->dp_port_num, count, in_interrupt() ); 1270 1271 /* copy user data (which can sleep) before getting spin lock */ 1272 count = min( count, port->bulk_out_size-2 ); 1273 count = min( 64, count); 1274 1275 /* be sure only one write proceeds at a time */ 1276 /* there are races on the port private buffer */ 1277 /* and races to check write_urb->status */ 1278 spin_lock_irqsave( &priv->dp_port_lock, flags ); 1279 1280 /* wait for urb status clear to submit another urb */ 1281 if( port->write_urb->status == -EINPROGRESS 1282 || priv->dp_write_urb_in_use ) { 1283 1284 /* buffer data if count is 1 (probably put_char) if possible */ 1285 if( count == 1 && priv->dp_out_buf_len < DIGI_OUT_BUF_SIZE ) { 1286 priv->dp_out_buf[priv->dp_out_buf_len++] = *buf; 1287 new_len = 1; 1288 } else { 1289 new_len = 0; 1290 } 1291 1292 spin_unlock_irqrestore( &priv->dp_port_lock, flags ); 1293 1294 return( new_len ); 1295 1296 } 1297 1298 /* allow space for any buffered data and for new data, up to */ 1299 /* transfer buffer size - 2 (for command and length bytes) */ 1300 new_len = min(count, port->bulk_out_size-2-priv->dp_out_buf_len); 1301 data_len = new_len + priv->dp_out_buf_len; 1302 1303 if( data_len == 0 ) { 1304 spin_unlock_irqrestore( &priv->dp_port_lock, flags ); 1305 return( 0 ); 1306 } 1307 1308 port->write_urb->transfer_buffer_length = data_len+2; 1309 port->write_urb->dev = port->serial->dev; 1310 1311 *data++ = DIGI_CMD_SEND_DATA; 1312 *data++ = data_len; 1313 1314 /* copy in buffered data first */ 1315 memcpy( data, priv->dp_out_buf, priv->dp_out_buf_len ); 1316 data += priv->dp_out_buf_len; 1317 1318 /* copy in new data */ 1319 memcpy( data, buf, new_len ); 1320 1321 if( (ret=usb_submit_urb(port->write_urb, GFP_ATOMIC)) == 0 ) { 1322 priv->dp_write_urb_in_use = 1; 1323 ret = new_len; 1324 priv->dp_out_buf_len = 0; 1325 } 1326 1327 /* return length of new data written, or error */ 1328 spin_unlock_irqrestore( &priv->dp_port_lock, flags ); 1329 if( ret < 0 ) { 1330 err("%s: usb_submit_urb failed, ret=%d, port=%d", __FUNCTION__, 1331 ret, priv->dp_port_num ); 1332 } 1333 1334 dbg( "digi_write: returning %d", ret ); 1335 return( ret ); 1336 1337 } 1338 1339 1340 static void digi_write_bulk_callback( struct urb *urb, struct pt_regs *regs ) 1341 { 1342 1343 struct usb_serial_port *port = (struct usb_serial_port *)urb->context; 1344 struct usb_serial *serial; 1345 struct digi_port *priv; 1346 struct digi_serial *serial_priv; 1347 int ret = 0; 1348 1349 1350 dbg( "digi_write_bulk_callback: TOP, urb->status=%d", urb->status ); 1351 1352 /* port and serial sanity check */ 1353 if( port == NULL || (priv=usb_get_serial_port_data(port)) == NULL ) { 1354 err("%s: port or port->private is NULL, status=%d", __FUNCTION__, 1355 urb->status ); 1356 return; 1357 } 1358 serial = port->serial; 1359 if( serial == NULL || (serial_priv=usb_get_serial_data(serial)) == NULL ) { 1360 err("%s: serial or serial->private is NULL, status=%d", __FUNCTION__, urb->status ); 1361 return; 1362 } 1363 1364 /* handle oob callback */ 1365 if( priv->dp_port_num == serial_priv->ds_oob_port_num ) { 1366 dbg( "digi_write_bulk_callback: oob callback" ); 1367 spin_lock( &priv->dp_port_lock ); 1368 priv->dp_write_urb_in_use = 0; 1369 wake_up_interruptible( &port->write_wait ); 1370 spin_unlock( &priv->dp_port_lock ); 1371 return; 1372 } 1373 1374 /* try to send any buffered data on this port, if it is open */ 1375 spin_lock( &priv->dp_port_lock ); 1376 priv->dp_write_urb_in_use = 0; 1377 if( port->open_count && port->write_urb->status != -EINPROGRESS 1378 && priv->dp_out_buf_len > 0 ) { 1379 1380 *((unsigned char *)(port->write_urb->transfer_buffer)) 1381 = (unsigned char)DIGI_CMD_SEND_DATA; 1382 *((unsigned char *)(port->write_urb->transfer_buffer)+1) 1383 = (unsigned char)priv->dp_out_buf_len; 1384 1385 port->write_urb->transfer_buffer_length 1386 = priv->dp_out_buf_len+2; 1387 port->write_urb->dev = serial->dev; 1388 1389 memcpy( port->write_urb->transfer_buffer+2, priv->dp_out_buf, 1390 priv->dp_out_buf_len ); 1391 1392 if( (ret=usb_submit_urb(port->write_urb, GFP_ATOMIC)) == 0 ) { 1393 priv->dp_write_urb_in_use = 1; 1394 priv->dp_out_buf_len = 0; 1395 } 1396 1397 } 1398 1399 /* wake up processes sleeping on writes immediately */ 1400 digi_wakeup_write( port ); 1401 1402 /* also queue up a wakeup at scheduler time, in case we */ 1403 /* lost the race in write_chan(). */ 1404 schedule_work(&priv->dp_wakeup_work); 1405 1406 spin_unlock( &priv->dp_port_lock ); 1407 1408 if( ret ) { 1409 err("%s: usb_submit_urb failed, ret=%d, port=%d", __FUNCTION__, 1410 ret, priv->dp_port_num ); 1411 } 1412 1413 } 1414 1415 1416 static int digi_write_room( struct usb_serial_port *port ) 1417 { 1418 1419 int room; 1420 struct digi_port *priv = usb_get_serial_port_data(port); 1421 unsigned long flags = 0; 1422 1423 1424 spin_lock_irqsave( &priv->dp_port_lock, flags ); 1425 1426 if( port->write_urb->status == -EINPROGRESS 1427 || priv->dp_write_urb_in_use ) 1428 room = 0; 1429 else 1430 room = port->bulk_out_size - 2 - priv->dp_out_buf_len; 1431 1432 spin_unlock_irqrestore( &priv->dp_port_lock, flags ); 1433 1434 dbg( "digi_write_room: port=%d, room=%d", priv->dp_port_num, room ); 1435 return( room ); 1436 1437 } 1438 1439 1440 static int digi_chars_in_buffer( struct usb_serial_port *port ) 1441 { 1442 1443 struct digi_port *priv = usb_get_serial_port_data(port); 1444 1445 1446 if( port->write_urb->status == -EINPROGRESS 1447 || priv->dp_write_urb_in_use ) { 1448 dbg( "digi_chars_in_buffer: port=%d, chars=%d", priv->dp_port_num, port->bulk_out_size - 2 ); 1449 /* return( port->bulk_out_size - 2 ); */ 1450 return( 256 ); 1451 } else { 1452 dbg( "digi_chars_in_buffer: port=%d, chars=%d", priv->dp_port_num, priv->dp_out_buf_len ); 1453 return( priv->dp_out_buf_len ); 1454 } 1455 1456 } 1457 1458 1459 static int digi_open( struct usb_serial_port *port, struct file *filp ) 1460 { 1461 1462 int ret; 1463 unsigned char buf[32]; 1464 struct digi_port *priv = usb_get_serial_port_data(port); 1465 struct termios not_termios; 1466 unsigned long flags = 0; 1467 1468 1469 dbg( "digi_open: TOP: port=%d, open_count=%d", priv->dp_port_num, port->open_count ); 1470 1471 /* be sure the device is started up */ 1472 if( digi_startup_device( port->serial ) != 0 ) 1473 return( -ENXIO ); 1474 1475 spin_lock_irqsave( &priv->dp_port_lock, flags ); 1476 1477 /* don't wait on a close in progress for non-blocking opens */ 1478 if( priv->dp_in_close && (filp->f_flags&(O_NDELAY|O_NONBLOCK)) == 0 ) { 1479 spin_unlock_irqrestore( &priv->dp_port_lock, flags ); 1480 return( -EAGAIN ); 1481 } 1482 1483 /* wait for a close in progress to finish */ 1484 while( priv->dp_in_close ) { 1485 cond_wait_interruptible_timeout_irqrestore( 1486 &priv->dp_close_wait, DIGI_RETRY_TIMEOUT, 1487 &priv->dp_port_lock, flags ); 1488 if( signal_pending(current) ) { 1489 return( -EINTR ); 1490 } 1491 spin_lock_irqsave( &priv->dp_port_lock, flags ); 1492 } 1493 1494 spin_unlock_irqrestore( &priv->dp_port_lock, flags ); 1495 1496 /* read modem signals automatically whenever they change */ 1497 buf[0] = DIGI_CMD_READ_INPUT_SIGNALS; 1498 buf[1] = priv->dp_port_num; 1499 buf[2] = DIGI_ENABLE; 1500 buf[3] = 0; 1501 1502 /* flush fifos */ 1503 buf[4] = DIGI_CMD_IFLUSH_FIFO; 1504 buf[5] = priv->dp_port_num; 1505 buf[6] = DIGI_FLUSH_TX | DIGI_FLUSH_RX; 1506 buf[7] = 0; 1507 1508 if( (ret=digi_write_oob_command( port, buf, 8, 1 )) != 0 ) 1509 dbg( "digi_open: write oob failed, ret=%d", ret ); 1510 1511 /* set termios settings */ 1512 not_termios.c_cflag = ~port->tty->termios->c_cflag; 1513 not_termios.c_iflag = ~port->tty->termios->c_iflag; 1514 digi_set_termios( port, ¬_termios ); 1515 1516 /* set DTR and RTS */ 1517 digi_set_modem_signals( port, TIOCM_DTR|TIOCM_RTS, 1 ); 1518 1519 return( 0 ); 1520 1521 } 1522 1523 1524 static void digi_close( struct usb_serial_port *port, struct file *filp ) 1525 { 1526 DEFINE_WAIT(wait); 1527 int ret; 1528 unsigned char buf[32]; 1529 struct tty_struct *tty = port->tty; 1530 struct digi_port *priv = usb_get_serial_port_data(port); 1531 unsigned long flags = 0; 1532 1533 1534 dbg( "digi_close: TOP: port=%d, open_count=%d", priv->dp_port_num, port->open_count ); 1535 1536 1537 /* if disconnected, just clear flags */ 1538 if (!usb_get_intfdata(port->serial->interface)) 1539 goto exit; 1540 1541 /* do cleanup only after final close on this port */ 1542 spin_lock_irqsave( &priv->dp_port_lock, flags ); 1543 priv->dp_in_close = 1; 1544 spin_unlock_irqrestore( &priv->dp_port_lock, flags ); 1545 1546 /* tell line discipline to process only XON/XOFF */ 1547 tty->closing = 1; 1548 1549 /* wait for output to drain */ 1550 if( (filp->f_flags&(O_NDELAY|O_NONBLOCK)) == 0 ) { 1551 tty_wait_until_sent( tty, DIGI_CLOSE_TIMEOUT ); 1552 } 1553 1554 /* flush driver and line discipline buffers */ 1555 if( tty->driver->flush_buffer ) 1556 tty->driver->flush_buffer( tty ); 1557 tty_ldisc_flush(tty); 1558 1559 if (port->serial->dev) { 1560 /* wait for transmit idle */ 1561 if( (filp->f_flags&(O_NDELAY|O_NONBLOCK)) == 0 ) { 1562 digi_transmit_idle( port, DIGI_CLOSE_TIMEOUT ); 1563 } 1564 1565 /* drop DTR and RTS */ 1566 digi_set_modem_signals( port, 0, 0 ); 1567 1568 /* disable input flow control */ 1569 buf[0] = DIGI_CMD_SET_INPUT_FLOW_CONTROL; 1570 buf[1] = priv->dp_port_num; 1571 buf[2] = DIGI_DISABLE; 1572 buf[3] = 0; 1573 1574 /* disable output flow control */ 1575 buf[4] = DIGI_CMD_SET_OUTPUT_FLOW_CONTROL; 1576 buf[5] = priv->dp_port_num; 1577 buf[6] = DIGI_DISABLE; 1578 buf[7] = 0; 1579 1580 /* disable reading modem signals automatically */ 1581 buf[8] = DIGI_CMD_READ_INPUT_SIGNALS; 1582 buf[9] = priv->dp_port_num; 1583 buf[10] = DIGI_DISABLE; 1584 buf[11] = 0; 1585 1586 /* disable receive */ 1587 buf[12] = DIGI_CMD_RECEIVE_ENABLE; 1588 buf[13] = priv->dp_port_num; 1589 buf[14] = DIGI_DISABLE; 1590 buf[15] = 0; 1591 1592 /* flush fifos */ 1593 buf[16] = DIGI_CMD_IFLUSH_FIFO; 1594 buf[17] = priv->dp_port_num; 1595 buf[18] = DIGI_FLUSH_TX | DIGI_FLUSH_RX; 1596 buf[19] = 0; 1597 1598 if( (ret=digi_write_oob_command( port, buf, 20, 0 )) != 0 ) 1599 dbg( "digi_close: write oob failed, ret=%d", ret ); 1600 1601 /* wait for final commands on oob port to complete */ 1602 prepare_to_wait(&priv->dp_flush_wait, &wait, TASK_INTERRUPTIBLE); 1603 schedule_timeout(DIGI_CLOSE_TIMEOUT); 1604 finish_wait(&priv->dp_flush_wait, &wait); 1605 1606 /* shutdown any outstanding bulk writes */ 1607 usb_kill_urb(port->write_urb); 1608 } 1609 1610 tty->closing = 0; 1611 1612 exit: 1613 spin_lock_irqsave( &priv->dp_port_lock, flags ); 1614 priv->dp_write_urb_in_use = 0; 1615 priv->dp_in_close = 0; 1616 wake_up_interruptible( &priv->dp_close_wait ); 1617 spin_unlock_irqrestore( &priv->dp_port_lock, flags ); 1618 1619 dbg( "digi_close: done" ); 1620 } 1621 1622 1623 /* 1624 * Digi Startup Device 1625 * 1626 * Starts reads on all ports. Must be called AFTER startup, with 1627 * urbs initialized. Returns 0 if successful, non-zero error otherwise. 1628 */ 1629 1630 static int digi_startup_device( struct usb_serial *serial ) 1631 { 1632 1633 int i,ret = 0; 1634 struct digi_serial *serial_priv = usb_get_serial_data(serial); 1635 struct usb_serial_port *port; 1636 1637 1638 /* be sure this happens exactly once */ 1639 spin_lock( &serial_priv->ds_serial_lock ); 1640 if( serial_priv->ds_device_started ) { 1641 spin_unlock( &serial_priv->ds_serial_lock ); 1642 return( 0 ); 1643 } 1644 serial_priv->ds_device_started = 1; 1645 spin_unlock( &serial_priv->ds_serial_lock ); 1646 1647 /* start reading from each bulk in endpoint for the device */ 1648 /* set USB_DISABLE_SPD flag for write bulk urbs */ 1649 for( i=0; i<serial->type->num_ports+1; i++ ) { 1650 1651 port = serial->port[i]; 1652 1653 port->write_urb->dev = port->serial->dev; 1654 1655 if( (ret=usb_submit_urb(port->read_urb, GFP_KERNEL)) != 0 ) { 1656 err("%s: usb_submit_urb failed, ret=%d, port=%d", __FUNCTION__, 1657 ret, i ); 1658 break; 1659 } 1660 1661 } 1662 1663 return( ret ); 1664 1665 } 1666 1667 1668 static int digi_startup( struct usb_serial *serial ) 1669 { 1670 1671 int i; 1672 struct digi_port *priv; 1673 struct digi_serial *serial_priv; 1674 1675 1676 dbg( "digi_startup: TOP" ); 1677 1678 /* allocate the private data structures for all ports */ 1679 /* number of regular ports + 1 for the out-of-band port */ 1680 for( i=0; i<serial->type->num_ports+1; i++ ) { 1681 1682 /* allocate port private structure */ 1683 priv = (struct digi_port *)kmalloc( sizeof(struct digi_port), 1684 GFP_KERNEL ); 1685 if( priv == (struct digi_port *)0 ) { 1686 while( --i >= 0 ) 1687 kfree( usb_get_serial_port_data(serial->port[i]) ); 1688 return( 1 ); /* error */ 1689 } 1690 1691 /* initialize port private structure */ 1692 spin_lock_init( &priv->dp_port_lock ); 1693 priv->dp_port_num = i; 1694 priv->dp_out_buf_len = 0; 1695 priv->dp_in_buf_len = 0; 1696 priv->dp_write_urb_in_use = 0; 1697 priv->dp_modem_signals = 0; 1698 init_waitqueue_head( &priv->dp_modem_change_wait ); 1699 priv->dp_transmit_idle = 0; 1700 init_waitqueue_head( &priv->dp_transmit_idle_wait ); 1701 priv->dp_throttled = 0; 1702 priv->dp_throttle_restart = 0; 1703 init_waitqueue_head( &priv->dp_flush_wait ); 1704 priv->dp_in_close = 0; 1705 init_waitqueue_head( &priv->dp_close_wait ); 1706 INIT_WORK(&priv->dp_wakeup_work, 1707 digi_wakeup_write_lock, serial->port[i]); 1708 1709 /* initialize write wait queue for this port */ 1710 init_waitqueue_head( &serial->port[i]->write_wait ); 1711 1712 usb_set_serial_port_data(serial->port[i], priv); 1713 } 1714 1715 /* allocate serial private structure */ 1716 serial_priv = (struct digi_serial *)kmalloc( sizeof(struct digi_serial), 1717 GFP_KERNEL ); 1718 if( serial_priv == (struct digi_serial *)0 ) { 1719 for( i=0; i<serial->type->num_ports+1; i++ ) 1720 kfree( usb_get_serial_port_data(serial->port[i]) ); 1721 return( 1 ); /* error */ 1722 } 1723 1724 /* initialize serial private structure */ 1725 spin_lock_init( &serial_priv->ds_serial_lock ); 1726 serial_priv->ds_oob_port_num = serial->type->num_ports; 1727 serial_priv->ds_oob_port = serial->port[serial_priv->ds_oob_port_num]; 1728 serial_priv->ds_device_started = 0; 1729 usb_set_serial_data(serial, serial_priv); 1730 1731 return( 0 ); 1732 1733 } 1734 1735 1736 static void digi_shutdown( struct usb_serial *serial ) 1737 { 1738 1739 int i; 1740 1741 1742 dbg( "digi_shutdown: TOP, in_interrupt()=%ld", in_interrupt() ); 1743 1744 /* stop reads and writes on all ports */ 1745 for( i=0; i<serial->type->num_ports+1; i++ ) { 1746 usb_kill_urb(serial->port[i]->read_urb); 1747 usb_kill_urb(serial->port[i]->write_urb); 1748 } 1749 1750 /* free the private data structures for all ports */ 1751 /* number of regular ports + 1 for the out-of-band port */ 1752 for( i=0; i<serial->type->num_ports+1; i++ ) 1753 kfree( usb_get_serial_port_data(serial->port[i]) ); 1754 kfree( usb_get_serial_data(serial) ); 1755 } 1756 1757 1758 static void digi_read_bulk_callback( struct urb *urb, struct pt_regs *regs ) 1759 { 1760 1761 struct usb_serial_port *port = (struct usb_serial_port *)urb->context; 1762 struct digi_port *priv; 1763 struct digi_serial *serial_priv; 1764 int ret; 1765 1766 1767 dbg( "digi_read_bulk_callback: TOP" ); 1768 1769 /* port sanity check, do not resubmit if port is not valid */ 1770 if( port == NULL || (priv=usb_get_serial_port_data(port)) == NULL ) { 1771 err("%s: port or port->private is NULL, status=%d", __FUNCTION__, 1772 urb->status ); 1773 return; 1774 } 1775 if( port->serial == NULL 1776 || (serial_priv=usb_get_serial_data(port->serial)) == NULL ) { 1777 err("%s: serial is bad or serial->private is NULL, status=%d", __FUNCTION__, urb->status ); 1778 return; 1779 } 1780 1781 /* do not resubmit urb if it has any status error */ 1782 if( urb->status ) { 1783 err("%s: nonzero read bulk status: status=%d, port=%d", __FUNCTION__, urb->status, priv->dp_port_num ); 1784 return; 1785 } 1786 1787 /* handle oob or inb callback, do not resubmit if error */ 1788 if( priv->dp_port_num == serial_priv->ds_oob_port_num ) { 1789 if( digi_read_oob_callback( urb ) != 0 ) 1790 return; 1791 } else { 1792 if( digi_read_inb_callback( urb ) != 0 ) 1793 return; 1794 } 1795 1796 /* continue read */ 1797 urb->dev = port->serial->dev; 1798 if( (ret=usb_submit_urb(urb, GFP_ATOMIC)) != 0 ) { 1799 err("%s: failed resubmitting urb, ret=%d, port=%d", __FUNCTION__, 1800 ret, priv->dp_port_num ); 1801 } 1802 1803 } 1804 1805 1806 /* 1807 * Digi Read INB Callback 1808 * 1809 * Digi Read INB Callback handles reads on the in band ports, sending 1810 * the data on to the tty subsystem. When called we know port and 1811 * port->private are not NULL and port->serial has been validated. 1812 * It returns 0 if successful, 1 if successful but the port is 1813 * throttled, and -1 if the sanity checks failed. 1814 */ 1815 1816 static int digi_read_inb_callback( struct urb *urb ) 1817 { 1818 1819 struct usb_serial_port *port = (struct usb_serial_port *)urb->context; 1820 struct tty_struct *tty = port->tty; 1821 struct digi_port *priv = usb_get_serial_port_data(port); 1822 int opcode = ((unsigned char *)urb->transfer_buffer)[0]; 1823 int len = ((unsigned char *)urb->transfer_buffer)[1]; 1824 int status = ((unsigned char *)urb->transfer_buffer)[2]; 1825 unsigned char *data = ((unsigned char *)urb->transfer_buffer)+3; 1826 int flag,throttled; 1827 int i; 1828 1829 /* do not process callbacks on closed ports */ 1830 /* but do continue the read chain */ 1831 if( port->open_count == 0 ) 1832 return( 0 ); 1833 1834 /* short/multiple packet check */ 1835 if( urb->actual_length != len + 2 ) { 1836 err("%s: INCOMPLETE OR MULTIPLE PACKET, urb->status=%d, port=%d, opcode=%d, len=%d, actual_length=%d, status=%d", __FUNCTION__, urb->status, priv->dp_port_num, opcode, len, urb->actual_length, status ); 1837 return( -1 ); 1838 } 1839 1840 spin_lock( &priv->dp_port_lock ); 1841 1842 /* check for throttle; if set, do not resubmit read urb */ 1843 /* indicate the read chain needs to be restarted on unthrottle */ 1844 throttled = priv->dp_throttled; 1845 if( throttled ) 1846 priv->dp_throttle_restart = 1; 1847 1848 /* receive data */ 1849 if( opcode == DIGI_CMD_RECEIVE_DATA ) { 1850 1851 /* get flag from status */ 1852 flag = 0; 1853 1854 /* overrun is special, not associated with a char */ 1855 if( status & DIGI_OVERRUN_ERROR ) { 1856 tty_insert_flip_char( tty, 0, TTY_OVERRUN ); 1857 } 1858 1859 /* break takes precedence over parity, */ 1860 /* which takes precedence over framing errors */ 1861 if( status & DIGI_BREAK_ERROR ) { 1862 flag = TTY_BREAK; 1863 } else if( status & DIGI_PARITY_ERROR ) { 1864 flag = TTY_PARITY; 1865 } else if( status & DIGI_FRAMING_ERROR ) { 1866 flag = TTY_FRAME; 1867 } 1868 1869 /* data length is len-1 (one byte of len is status) */ 1870 --len; 1871 1872 if( throttled ) { 1873 1874 len = min( len, 1875 DIGI_IN_BUF_SIZE - priv->dp_in_buf_len ); 1876 1877 if( len > 0 ) { 1878 memcpy( priv->dp_in_buf + priv->dp_in_buf_len, 1879 data, len ); 1880 memset( priv->dp_in_flag_buf 1881 + priv->dp_in_buf_len, flag, len ); 1882 priv->dp_in_buf_len += len; 1883 } 1884 1885 } else { 1886 len = tty_buffer_request_room(tty, len); 1887 if( len > 0 ) { 1888 /* Hot path */ 1889 if(flag == TTY_NORMAL) 1890 tty_insert_flip_string(tty, data, len); 1891 else { 1892 for(i = 0; i < len; i++) 1893 tty_insert_flip_char(tty, data[i], flag); 1894 } 1895 tty_flip_buffer_push( tty ); 1896 } 1897 } 1898 } 1899 1900 spin_unlock( &priv->dp_port_lock ); 1901 1902 if( opcode == DIGI_CMD_RECEIVE_DISABLE ) { 1903 dbg("%s: got RECEIVE_DISABLE", __FUNCTION__ ); 1904 } else if( opcode != DIGI_CMD_RECEIVE_DATA ) { 1905 dbg("%s: unknown opcode: %d", __FUNCTION__, opcode ); 1906 } 1907 1908 return( throttled ? 1 : 0 ); 1909 1910 } 1911 1912 1913 /* 1914 * Digi Read OOB Callback 1915 * 1916 * Digi Read OOB Callback handles reads on the out of band port. 1917 * When called we know port and port->private are not NULL and 1918 * the port->serial is valid. It returns 0 if successful, and 1919 * -1 if the sanity checks failed. 1920 */ 1921 1922 static int digi_read_oob_callback( struct urb *urb ) 1923 { 1924 1925 struct usb_serial_port *port = (struct usb_serial_port *)urb->context; 1926 struct usb_serial *serial = port->serial; 1927 struct digi_port *priv = usb_get_serial_port_data(port); 1928 int opcode, line, status, val; 1929 int i; 1930 1931 1932 dbg( "digi_read_oob_callback: port=%d, len=%d", priv->dp_port_num, 1933 urb->actual_length ); 1934 1935 /* handle each oob command */ 1936 for( i=0; i<urb->actual_length-3; ) { 1937 1938 opcode = ((unsigned char *)urb->transfer_buffer)[i++]; 1939 line = ((unsigned char *)urb->transfer_buffer)[i++]; 1940 status = ((unsigned char *)urb->transfer_buffer)[i++]; 1941 val = ((unsigned char *)urb->transfer_buffer)[i++]; 1942 1943 dbg( "digi_read_oob_callback: opcode=%d, line=%d, status=%d, val=%d", 1944 opcode, line, status, val ); 1945 1946 if( status != 0 || line >= serial->type->num_ports ) 1947 continue; 1948 1949 port = serial->port[line]; 1950 1951 if ((priv=usb_get_serial_port_data(port)) == NULL ) 1952 return -1; 1953 1954 if( opcode == DIGI_CMD_READ_INPUT_SIGNALS ) { 1955 1956 spin_lock( &priv->dp_port_lock ); 1957 1958 /* convert from digi flags to termiox flags */ 1959 if( val & DIGI_READ_INPUT_SIGNALS_CTS ) { 1960 priv->dp_modem_signals |= TIOCM_CTS; 1961 /* port must be open to use tty struct */ 1962 if( port->open_count 1963 && port->tty->termios->c_cflag & CRTSCTS ) { 1964 port->tty->hw_stopped = 0; 1965 digi_wakeup_write( port ); 1966 } 1967 } else { 1968 priv->dp_modem_signals &= ~TIOCM_CTS; 1969 /* port must be open to use tty struct */ 1970 if( port->open_count 1971 && port->tty->termios->c_cflag & CRTSCTS ) { 1972 port->tty->hw_stopped = 1; 1973 } 1974 } 1975 if( val & DIGI_READ_INPUT_SIGNALS_DSR ) 1976 priv->dp_modem_signals |= TIOCM_DSR; 1977 else 1978 priv->dp_modem_signals &= ~TIOCM_DSR; 1979 if( val & DIGI_READ_INPUT_SIGNALS_RI ) 1980 priv->dp_modem_signals |= TIOCM_RI; 1981 else 1982 priv->dp_modem_signals &= ~TIOCM_RI; 1983 if( val & DIGI_READ_INPUT_SIGNALS_DCD ) 1984 priv->dp_modem_signals |= TIOCM_CD; 1985 else 1986 priv->dp_modem_signals &= ~TIOCM_CD; 1987 1988 wake_up_interruptible( &priv->dp_modem_change_wait ); 1989 spin_unlock( &priv->dp_port_lock ); 1990 1991 } else if( opcode == DIGI_CMD_TRANSMIT_IDLE ) { 1992 1993 spin_lock( &priv->dp_port_lock ); 1994 priv->dp_transmit_idle = 1; 1995 wake_up_interruptible( &priv->dp_transmit_idle_wait ); 1996 spin_unlock( &priv->dp_port_lock ); 1997 1998 } else if( opcode == DIGI_CMD_IFLUSH_FIFO ) { 1999 2000 wake_up_interruptible( &priv->dp_flush_wait ); 2001 2002 } 2003 2004 } 2005 2006 return( 0 ); 2007 2008 } 2009 2010 2011 static int __init digi_init (void) 2012 { 2013 int retval; 2014 retval = usb_serial_register(&digi_acceleport_2_device); 2015 if (retval) 2016 goto failed_acceleport_2_device; 2017 retval = usb_serial_register(&digi_acceleport_4_device); 2018 if (retval) 2019 goto failed_acceleport_4_device; 2020 retval = usb_register(&digi_driver); 2021 if (retval) 2022 goto failed_usb_register; 2023 info(DRIVER_VERSION ":" DRIVER_DESC); 2024 return 0; 2025 failed_usb_register: 2026 usb_serial_deregister(&digi_acceleport_4_device); 2027 failed_acceleport_4_device: 2028 usb_serial_deregister(&digi_acceleport_2_device); 2029 failed_acceleport_2_device: 2030 return retval; 2031 } 2032 2033 2034 static void __exit digi_exit (void) 2035 { 2036 usb_deregister (&digi_driver); 2037 usb_serial_deregister (&digi_acceleport_2_device); 2038 usb_serial_deregister (&digi_acceleport_4_device); 2039 } 2040 2041 2042 module_init(digi_init); 2043 module_exit(digi_exit); 2044 2045 2046 MODULE_AUTHOR( DRIVER_AUTHOR ); 2047 MODULE_DESCRIPTION( DRIVER_DESC ); 2048 MODULE_LICENSE("GPL"); 2049 2050 module_param(debug, bool, S_IRUGO | S_IWUSR); 2051 MODULE_PARM_DESC(debug, "Debug enabled or not"); 2052