1 // SPDX-License-Identifier: GPL-2.0+ 2 /* 3 * Digi AccelePort USB-4 and USB-2 Serial Converters 4 * 5 * Copyright 2000 by Digi International 6 * 7 * Shamelessly based on Brian Warner's keyspan_pda.c and Greg Kroah-Hartman's 8 * usb-serial driver. 9 * 10 * Peter Berger (pberger@brimson.com) 11 * Al Borchers (borchers@steinerpoint.com) 12 */ 13 14 #include <linux/kernel.h> 15 #include <linux/errno.h> 16 #include <linux/slab.h> 17 #include <linux/tty.h> 18 #include <linux/tty_driver.h> 19 #include <linux/tty_flip.h> 20 #include <linux/module.h> 21 #include <linux/spinlock.h> 22 #include <linux/uaccess.h> 23 #include <linux/usb.h> 24 #include <linux/wait.h> 25 #include <linux/sched/signal.h> 26 #include <linux/usb/serial.h> 27 28 /* Defines */ 29 30 #define DRIVER_AUTHOR "Peter Berger <pberger@brimson.com>, Al Borchers <borchers@steinerpoint.com>" 31 #define DRIVER_DESC "Digi AccelePort USB-2/USB-4 Serial Converter driver" 32 33 /* port output buffer length -- must be <= transfer buffer length - 2 */ 34 /* so we can be sure to send the full buffer in one urb */ 35 #define DIGI_OUT_BUF_SIZE 8 36 37 /* port input buffer length -- must be >= transfer buffer length - 3 */ 38 /* so we can be sure to hold at least one full buffer from one urb */ 39 #define DIGI_IN_BUF_SIZE 64 40 41 /* retry timeout while sleeping */ 42 #define DIGI_RETRY_TIMEOUT (HZ/10) 43 44 /* timeout while waiting for tty output to drain in close */ 45 /* this delay is used twice in close, so the total delay could */ 46 /* be twice this value */ 47 #define DIGI_CLOSE_TIMEOUT (5*HZ) 48 49 50 /* AccelePort USB Defines */ 51 52 /* ids */ 53 #define DIGI_VENDOR_ID 0x05c5 54 #define DIGI_2_ID 0x0002 /* USB-2 */ 55 #define DIGI_4_ID 0x0004 /* USB-4 */ 56 57 /* commands 58 * "INB": can be used on the in-band endpoint 59 * "OOB": can be used on the out-of-band endpoint 60 */ 61 #define DIGI_CMD_SET_BAUD_RATE 0 /* INB, OOB */ 62 #define DIGI_CMD_SET_WORD_SIZE 1 /* INB, OOB */ 63 #define DIGI_CMD_SET_PARITY 2 /* INB, OOB */ 64 #define DIGI_CMD_SET_STOP_BITS 3 /* INB, OOB */ 65 #define DIGI_CMD_SET_INPUT_FLOW_CONTROL 4 /* INB, OOB */ 66 #define DIGI_CMD_SET_OUTPUT_FLOW_CONTROL 5 /* INB, OOB */ 67 #define DIGI_CMD_SET_DTR_SIGNAL 6 /* INB, OOB */ 68 #define DIGI_CMD_SET_RTS_SIGNAL 7 /* INB, OOB */ 69 #define DIGI_CMD_READ_INPUT_SIGNALS 8 /* OOB */ 70 #define DIGI_CMD_IFLUSH_FIFO 9 /* OOB */ 71 #define DIGI_CMD_RECEIVE_ENABLE 10 /* INB, OOB */ 72 #define DIGI_CMD_BREAK_CONTROL 11 /* INB, OOB */ 73 #define DIGI_CMD_LOCAL_LOOPBACK 12 /* INB, OOB */ 74 #define DIGI_CMD_TRANSMIT_IDLE 13 /* INB, OOB */ 75 #define DIGI_CMD_READ_UART_REGISTER 14 /* OOB */ 76 #define DIGI_CMD_WRITE_UART_REGISTER 15 /* INB, OOB */ 77 #define DIGI_CMD_AND_UART_REGISTER 16 /* INB, OOB */ 78 #define DIGI_CMD_OR_UART_REGISTER 17 /* INB, OOB */ 79 #define DIGI_CMD_SEND_DATA 18 /* INB */ 80 #define DIGI_CMD_RECEIVE_DATA 19 /* INB */ 81 #define DIGI_CMD_RECEIVE_DISABLE 20 /* INB */ 82 #define DIGI_CMD_GET_PORT_TYPE 21 /* OOB */ 83 84 /* baud rates */ 85 #define DIGI_BAUD_50 0 86 #define DIGI_BAUD_75 1 87 #define DIGI_BAUD_110 2 88 #define DIGI_BAUD_150 3 89 #define DIGI_BAUD_200 4 90 #define DIGI_BAUD_300 5 91 #define DIGI_BAUD_600 6 92 #define DIGI_BAUD_1200 7 93 #define DIGI_BAUD_1800 8 94 #define DIGI_BAUD_2400 9 95 #define DIGI_BAUD_4800 10 96 #define DIGI_BAUD_7200 11 97 #define DIGI_BAUD_9600 12 98 #define DIGI_BAUD_14400 13 99 #define DIGI_BAUD_19200 14 100 #define DIGI_BAUD_28800 15 101 #define DIGI_BAUD_38400 16 102 #define DIGI_BAUD_57600 17 103 #define DIGI_BAUD_76800 18 104 #define DIGI_BAUD_115200 19 105 #define DIGI_BAUD_153600 20 106 #define DIGI_BAUD_230400 21 107 #define DIGI_BAUD_460800 22 108 109 /* arguments */ 110 #define DIGI_WORD_SIZE_5 0 111 #define DIGI_WORD_SIZE_6 1 112 #define DIGI_WORD_SIZE_7 2 113 #define DIGI_WORD_SIZE_8 3 114 115 #define DIGI_PARITY_NONE 0 116 #define DIGI_PARITY_ODD 1 117 #define DIGI_PARITY_EVEN 2 118 #define DIGI_PARITY_MARK 3 119 #define DIGI_PARITY_SPACE 4 120 121 #define DIGI_STOP_BITS_1 0 122 #define DIGI_STOP_BITS_2 1 123 124 #define DIGI_INPUT_FLOW_CONTROL_XON_XOFF 1 125 #define DIGI_INPUT_FLOW_CONTROL_RTS 2 126 #define DIGI_INPUT_FLOW_CONTROL_DTR 4 127 128 #define DIGI_OUTPUT_FLOW_CONTROL_XON_XOFF 1 129 #define DIGI_OUTPUT_FLOW_CONTROL_CTS 2 130 #define DIGI_OUTPUT_FLOW_CONTROL_DSR 4 131 132 #define DIGI_DTR_INACTIVE 0 133 #define DIGI_DTR_ACTIVE 1 134 #define DIGI_DTR_INPUT_FLOW_CONTROL 2 135 136 #define DIGI_RTS_INACTIVE 0 137 #define DIGI_RTS_ACTIVE 1 138 #define DIGI_RTS_INPUT_FLOW_CONTROL 2 139 #define DIGI_RTS_TOGGLE 3 140 141 #define DIGI_FLUSH_TX 1 142 #define DIGI_FLUSH_RX 2 143 #define DIGI_RESUME_TX 4 /* clears xoff condition */ 144 145 #define DIGI_TRANSMIT_NOT_IDLE 0 146 #define DIGI_TRANSMIT_IDLE 1 147 148 #define DIGI_DISABLE 0 149 #define DIGI_ENABLE 1 150 151 #define DIGI_DEASSERT 0 152 #define DIGI_ASSERT 1 153 154 /* in band status codes */ 155 #define DIGI_OVERRUN_ERROR 4 156 #define DIGI_PARITY_ERROR 8 157 #define DIGI_FRAMING_ERROR 16 158 #define DIGI_BREAK_ERROR 32 159 160 /* out of band status */ 161 #define DIGI_NO_ERROR 0 162 #define DIGI_BAD_FIRST_PARAMETER 1 163 #define DIGI_BAD_SECOND_PARAMETER 2 164 #define DIGI_INVALID_LINE 3 165 #define DIGI_INVALID_OPCODE 4 166 167 /* input signals */ 168 #define DIGI_READ_INPUT_SIGNALS_SLOT 1 169 #define DIGI_READ_INPUT_SIGNALS_ERR 2 170 #define DIGI_READ_INPUT_SIGNALS_BUSY 4 171 #define DIGI_READ_INPUT_SIGNALS_PE 8 172 #define DIGI_READ_INPUT_SIGNALS_CTS 16 173 #define DIGI_READ_INPUT_SIGNALS_DSR 32 174 #define DIGI_READ_INPUT_SIGNALS_RI 64 175 #define DIGI_READ_INPUT_SIGNALS_DCD 128 176 177 178 /* Structures */ 179 180 struct digi_serial { 181 spinlock_t ds_serial_lock; 182 struct usb_serial_port *ds_oob_port; /* out-of-band port */ 183 int ds_oob_port_num; /* index of out-of-band port */ 184 int ds_device_started; 185 }; 186 187 struct digi_port { 188 spinlock_t dp_port_lock; 189 int dp_port_num; 190 int dp_out_buf_len; 191 unsigned char dp_out_buf[DIGI_OUT_BUF_SIZE]; 192 int dp_write_urb_in_use; 193 unsigned int dp_modem_signals; 194 int dp_transmit_idle; 195 wait_queue_head_t dp_transmit_idle_wait; 196 int dp_throttled; 197 int dp_throttle_restart; 198 wait_queue_head_t dp_flush_wait; 199 wait_queue_head_t dp_close_wait; /* wait queue for close */ 200 wait_queue_head_t write_wait; 201 struct usb_serial_port *dp_port; 202 }; 203 204 205 /* Local Function Declarations */ 206 207 static int digi_write_oob_command(struct usb_serial_port *port, 208 unsigned char *buf, int count, int interruptible); 209 static int digi_write_inb_command(struct usb_serial_port *port, 210 unsigned char *buf, int count, unsigned long timeout); 211 static int digi_set_modem_signals(struct usb_serial_port *port, 212 unsigned int modem_signals, int interruptible); 213 static int digi_transmit_idle(struct usb_serial_port *port, 214 unsigned long timeout); 215 static void digi_rx_throttle(struct tty_struct *tty); 216 static void digi_rx_unthrottle(struct tty_struct *tty); 217 static void digi_set_termios(struct tty_struct *tty, 218 struct usb_serial_port *port, 219 const struct ktermios *old_termios); 220 static int digi_break_ctl(struct tty_struct *tty, int break_state); 221 static int digi_tiocmget(struct tty_struct *tty); 222 static int digi_tiocmset(struct tty_struct *tty, unsigned int set, 223 unsigned int clear); 224 static int digi_write(struct tty_struct *tty, struct usb_serial_port *port, 225 const unsigned char *buf, int count); 226 static void digi_write_bulk_callback(struct urb *urb); 227 static unsigned int digi_write_room(struct tty_struct *tty); 228 static unsigned int digi_chars_in_buffer(struct tty_struct *tty); 229 static int digi_open(struct tty_struct *tty, struct usb_serial_port *port); 230 static void digi_close(struct usb_serial_port *port); 231 static void digi_dtr_rts(struct usb_serial_port *port, int on); 232 static int digi_startup_device(struct usb_serial *serial); 233 static int digi_startup(struct usb_serial *serial); 234 static void digi_disconnect(struct usb_serial *serial); 235 static void digi_release(struct usb_serial *serial); 236 static int digi_port_probe(struct usb_serial_port *port); 237 static void digi_port_remove(struct usb_serial_port *port); 238 static void digi_read_bulk_callback(struct urb *urb); 239 static int digi_read_inb_callback(struct urb *urb); 240 static int digi_read_oob_callback(struct urb *urb); 241 242 243 static const struct usb_device_id id_table_combined[] = { 244 { USB_DEVICE(DIGI_VENDOR_ID, DIGI_2_ID) }, 245 { USB_DEVICE(DIGI_VENDOR_ID, DIGI_4_ID) }, 246 { } /* Terminating entry */ 247 }; 248 249 static const struct usb_device_id id_table_2[] = { 250 { USB_DEVICE(DIGI_VENDOR_ID, DIGI_2_ID) }, 251 { } /* Terminating entry */ 252 }; 253 254 static const struct usb_device_id id_table_4[] = { 255 { USB_DEVICE(DIGI_VENDOR_ID, DIGI_4_ID) }, 256 { } /* Terminating entry */ 257 }; 258 259 MODULE_DEVICE_TABLE(usb, id_table_combined); 260 261 /* device info needed for the Digi serial converter */ 262 263 static struct usb_serial_driver digi_acceleport_2_device = { 264 .driver = { 265 .owner = THIS_MODULE, 266 .name = "digi_2", 267 }, 268 .description = "Digi 2 port USB adapter", 269 .id_table = id_table_2, 270 .num_ports = 3, 271 .num_bulk_in = 4, 272 .num_bulk_out = 4, 273 .open = digi_open, 274 .close = digi_close, 275 .dtr_rts = digi_dtr_rts, 276 .write = digi_write, 277 .write_room = digi_write_room, 278 .write_bulk_callback = digi_write_bulk_callback, 279 .read_bulk_callback = digi_read_bulk_callback, 280 .chars_in_buffer = digi_chars_in_buffer, 281 .throttle = digi_rx_throttle, 282 .unthrottle = digi_rx_unthrottle, 283 .set_termios = digi_set_termios, 284 .break_ctl = digi_break_ctl, 285 .tiocmget = digi_tiocmget, 286 .tiocmset = digi_tiocmset, 287 .attach = digi_startup, 288 .disconnect = digi_disconnect, 289 .release = digi_release, 290 .port_probe = digi_port_probe, 291 .port_remove = digi_port_remove, 292 }; 293 294 static struct usb_serial_driver digi_acceleport_4_device = { 295 .driver = { 296 .owner = THIS_MODULE, 297 .name = "digi_4", 298 }, 299 .description = "Digi 4 port USB adapter", 300 .id_table = id_table_4, 301 .num_ports = 4, 302 .num_bulk_in = 5, 303 .num_bulk_out = 5, 304 .open = digi_open, 305 .close = digi_close, 306 .write = digi_write, 307 .write_room = digi_write_room, 308 .write_bulk_callback = digi_write_bulk_callback, 309 .read_bulk_callback = digi_read_bulk_callback, 310 .chars_in_buffer = digi_chars_in_buffer, 311 .throttle = digi_rx_throttle, 312 .unthrottle = digi_rx_unthrottle, 313 .set_termios = digi_set_termios, 314 .break_ctl = digi_break_ctl, 315 .tiocmget = digi_tiocmget, 316 .tiocmset = digi_tiocmset, 317 .attach = digi_startup, 318 .disconnect = digi_disconnect, 319 .release = digi_release, 320 .port_probe = digi_port_probe, 321 .port_remove = digi_port_remove, 322 }; 323 324 static struct usb_serial_driver * const serial_drivers[] = { 325 &digi_acceleport_2_device, &digi_acceleport_4_device, NULL 326 }; 327 328 /* Functions */ 329 330 /* 331 * Cond Wait Interruptible Timeout Irqrestore 332 * 333 * Do spin_unlock_irqrestore and interruptible_sleep_on_timeout 334 * so that wake ups are not lost if they occur between the unlock 335 * and the sleep. In other words, spin_unlock_irqrestore and 336 * interruptible_sleep_on_timeout are "atomic" with respect to 337 * wake ups. This is used to implement condition variables. 338 * 339 * interruptible_sleep_on_timeout is deprecated and has been replaced 340 * with the equivalent code. 341 */ 342 343 static long cond_wait_interruptible_timeout_irqrestore( 344 wait_queue_head_t *q, long timeout, 345 spinlock_t *lock, unsigned long flags) 346 __releases(lock) 347 { 348 DEFINE_WAIT(wait); 349 350 prepare_to_wait(q, &wait, TASK_INTERRUPTIBLE); 351 spin_unlock_irqrestore(lock, flags); 352 timeout = schedule_timeout(timeout); 353 finish_wait(q, &wait); 354 355 return timeout; 356 } 357 358 /* 359 * Digi Write OOB Command 360 * 361 * Write commands on the out of band port. Commands are 4 362 * bytes each, multiple commands can be sent at once, and 363 * no command will be split across USB packets. Returns 0 364 * if successful, -EINTR if interrupted while sleeping and 365 * the interruptible flag is true, or a negative error 366 * returned by usb_submit_urb. 367 */ 368 369 static int digi_write_oob_command(struct usb_serial_port *port, 370 unsigned char *buf, int count, int interruptible) 371 { 372 int ret = 0; 373 int len; 374 struct usb_serial_port *oob_port = (struct usb_serial_port *)((struct digi_serial *)(usb_get_serial_data(port->serial)))->ds_oob_port; 375 struct digi_port *oob_priv = usb_get_serial_port_data(oob_port); 376 unsigned long flags; 377 378 dev_dbg(&port->dev, 379 "digi_write_oob_command: TOP: port=%d, count=%d\n", 380 oob_priv->dp_port_num, count); 381 382 spin_lock_irqsave(&oob_priv->dp_port_lock, flags); 383 while (count > 0) { 384 while (oob_priv->dp_write_urb_in_use) { 385 cond_wait_interruptible_timeout_irqrestore( 386 &oob_priv->write_wait, DIGI_RETRY_TIMEOUT, 387 &oob_priv->dp_port_lock, flags); 388 if (interruptible && signal_pending(current)) 389 return -EINTR; 390 spin_lock_irqsave(&oob_priv->dp_port_lock, flags); 391 } 392 393 /* len must be a multiple of 4, so commands are not split */ 394 len = min(count, oob_port->bulk_out_size); 395 if (len > 4) 396 len &= ~3; 397 memcpy(oob_port->write_urb->transfer_buffer, buf, len); 398 oob_port->write_urb->transfer_buffer_length = len; 399 ret = usb_submit_urb(oob_port->write_urb, GFP_ATOMIC); 400 if (ret == 0) { 401 oob_priv->dp_write_urb_in_use = 1; 402 count -= len; 403 buf += len; 404 } 405 } 406 spin_unlock_irqrestore(&oob_priv->dp_port_lock, flags); 407 if (ret) 408 dev_err(&port->dev, "%s: usb_submit_urb failed, ret=%d\n", 409 __func__, ret); 410 return ret; 411 412 } 413 414 415 /* 416 * Digi Write In Band Command 417 * 418 * Write commands on the given port. Commands are 4 419 * bytes each, multiple commands can be sent at once, and 420 * no command will be split across USB packets. If timeout 421 * is non-zero, write in band command will return after 422 * waiting unsuccessfully for the URB status to clear for 423 * timeout ticks. Returns 0 if successful, or a negative 424 * error returned by digi_write. 425 */ 426 427 static int digi_write_inb_command(struct usb_serial_port *port, 428 unsigned char *buf, int count, unsigned long timeout) 429 { 430 int ret = 0; 431 int len; 432 struct digi_port *priv = usb_get_serial_port_data(port); 433 unsigned char *data = port->write_urb->transfer_buffer; 434 unsigned long flags; 435 436 dev_dbg(&port->dev, "digi_write_inb_command: TOP: port=%d, count=%d\n", 437 priv->dp_port_num, count); 438 439 if (timeout) 440 timeout += jiffies; 441 else 442 timeout = ULONG_MAX; 443 444 spin_lock_irqsave(&priv->dp_port_lock, flags); 445 while (count > 0 && ret == 0) { 446 while (priv->dp_write_urb_in_use && 447 time_before(jiffies, timeout)) { 448 cond_wait_interruptible_timeout_irqrestore( 449 &priv->write_wait, DIGI_RETRY_TIMEOUT, 450 &priv->dp_port_lock, flags); 451 if (signal_pending(current)) 452 return -EINTR; 453 spin_lock_irqsave(&priv->dp_port_lock, flags); 454 } 455 456 /* len must be a multiple of 4 and small enough to */ 457 /* guarantee the write will send buffered data first, */ 458 /* so commands are in order with data and not split */ 459 len = min(count, port->bulk_out_size-2-priv->dp_out_buf_len); 460 if (len > 4) 461 len &= ~3; 462 463 /* write any buffered data first */ 464 if (priv->dp_out_buf_len > 0) { 465 data[0] = DIGI_CMD_SEND_DATA; 466 data[1] = priv->dp_out_buf_len; 467 memcpy(data + 2, priv->dp_out_buf, 468 priv->dp_out_buf_len); 469 memcpy(data + 2 + priv->dp_out_buf_len, buf, len); 470 port->write_urb->transfer_buffer_length 471 = priv->dp_out_buf_len + 2 + len; 472 } else { 473 memcpy(data, buf, len); 474 port->write_urb->transfer_buffer_length = len; 475 } 476 477 ret = usb_submit_urb(port->write_urb, GFP_ATOMIC); 478 if (ret == 0) { 479 priv->dp_write_urb_in_use = 1; 480 priv->dp_out_buf_len = 0; 481 count -= len; 482 buf += len; 483 } 484 485 } 486 spin_unlock_irqrestore(&priv->dp_port_lock, flags); 487 488 if (ret) 489 dev_err(&port->dev, 490 "%s: usb_submit_urb failed, ret=%d, port=%d\n", 491 __func__, ret, priv->dp_port_num); 492 return ret; 493 } 494 495 496 /* 497 * Digi Set Modem Signals 498 * 499 * Sets or clears DTR and RTS on the port, according to the 500 * modem_signals argument. Use TIOCM_DTR and TIOCM_RTS flags 501 * for the modem_signals argument. Returns 0 if successful, 502 * -EINTR if interrupted while sleeping, or a non-zero error 503 * returned by usb_submit_urb. 504 */ 505 506 static int digi_set_modem_signals(struct usb_serial_port *port, 507 unsigned int modem_signals, int interruptible) 508 { 509 510 int ret; 511 struct digi_port *port_priv = usb_get_serial_port_data(port); 512 struct usb_serial_port *oob_port = (struct usb_serial_port *) ((struct digi_serial *)(usb_get_serial_data(port->serial)))->ds_oob_port; 513 struct digi_port *oob_priv = usb_get_serial_port_data(oob_port); 514 unsigned char *data = oob_port->write_urb->transfer_buffer; 515 unsigned long flags; 516 517 dev_dbg(&port->dev, 518 "digi_set_modem_signals: TOP: port=%d, modem_signals=0x%x\n", 519 port_priv->dp_port_num, modem_signals); 520 521 spin_lock_irqsave(&oob_priv->dp_port_lock, flags); 522 spin_lock(&port_priv->dp_port_lock); 523 524 while (oob_priv->dp_write_urb_in_use) { 525 spin_unlock(&port_priv->dp_port_lock); 526 cond_wait_interruptible_timeout_irqrestore( 527 &oob_priv->write_wait, DIGI_RETRY_TIMEOUT, 528 &oob_priv->dp_port_lock, flags); 529 if (interruptible && signal_pending(current)) 530 return -EINTR; 531 spin_lock_irqsave(&oob_priv->dp_port_lock, flags); 532 spin_lock(&port_priv->dp_port_lock); 533 } 534 data[0] = DIGI_CMD_SET_DTR_SIGNAL; 535 data[1] = port_priv->dp_port_num; 536 data[2] = (modem_signals & TIOCM_DTR) ? 537 DIGI_DTR_ACTIVE : DIGI_DTR_INACTIVE; 538 data[3] = 0; 539 data[4] = DIGI_CMD_SET_RTS_SIGNAL; 540 data[5] = port_priv->dp_port_num; 541 data[6] = (modem_signals & TIOCM_RTS) ? 542 DIGI_RTS_ACTIVE : DIGI_RTS_INACTIVE; 543 data[7] = 0; 544 545 oob_port->write_urb->transfer_buffer_length = 8; 546 547 ret = usb_submit_urb(oob_port->write_urb, GFP_ATOMIC); 548 if (ret == 0) { 549 oob_priv->dp_write_urb_in_use = 1; 550 port_priv->dp_modem_signals &= ~(TIOCM_DTR | TIOCM_RTS); 551 port_priv->dp_modem_signals |= 552 modem_signals & (TIOCM_DTR | TIOCM_RTS); 553 } 554 spin_unlock(&port_priv->dp_port_lock); 555 spin_unlock_irqrestore(&oob_priv->dp_port_lock, flags); 556 if (ret) 557 dev_err(&port->dev, "%s: usb_submit_urb failed, ret=%d\n", 558 __func__, ret); 559 return ret; 560 } 561 562 /* 563 * Digi Transmit Idle 564 * 565 * Digi transmit idle waits, up to timeout ticks, for the transmitter 566 * to go idle. It returns 0 if successful or a negative error. 567 * 568 * There are race conditions here if more than one process is calling 569 * digi_transmit_idle on the same port at the same time. However, this 570 * is only called from close, and only one process can be in close on a 571 * port at a time, so its ok. 572 */ 573 574 static int digi_transmit_idle(struct usb_serial_port *port, 575 unsigned long timeout) 576 { 577 int ret; 578 unsigned char buf[2]; 579 struct digi_port *priv = usb_get_serial_port_data(port); 580 unsigned long flags; 581 582 spin_lock_irqsave(&priv->dp_port_lock, flags); 583 priv->dp_transmit_idle = 0; 584 spin_unlock_irqrestore(&priv->dp_port_lock, flags); 585 586 buf[0] = DIGI_CMD_TRANSMIT_IDLE; 587 buf[1] = 0; 588 589 timeout += jiffies; 590 591 ret = digi_write_inb_command(port, buf, 2, timeout - jiffies); 592 if (ret != 0) 593 return ret; 594 595 spin_lock_irqsave(&priv->dp_port_lock, flags); 596 597 while (time_before(jiffies, timeout) && !priv->dp_transmit_idle) { 598 cond_wait_interruptible_timeout_irqrestore( 599 &priv->dp_transmit_idle_wait, DIGI_RETRY_TIMEOUT, 600 &priv->dp_port_lock, flags); 601 if (signal_pending(current)) 602 return -EINTR; 603 spin_lock_irqsave(&priv->dp_port_lock, flags); 604 } 605 priv->dp_transmit_idle = 0; 606 spin_unlock_irqrestore(&priv->dp_port_lock, flags); 607 return 0; 608 609 } 610 611 612 static void digi_rx_throttle(struct tty_struct *tty) 613 { 614 unsigned long flags; 615 struct usb_serial_port *port = tty->driver_data; 616 struct digi_port *priv = usb_get_serial_port_data(port); 617 618 /* stop receiving characters by not resubmitting the read urb */ 619 spin_lock_irqsave(&priv->dp_port_lock, flags); 620 priv->dp_throttled = 1; 621 priv->dp_throttle_restart = 0; 622 spin_unlock_irqrestore(&priv->dp_port_lock, flags); 623 } 624 625 626 static void digi_rx_unthrottle(struct tty_struct *tty) 627 { 628 int ret = 0; 629 unsigned long flags; 630 struct usb_serial_port *port = tty->driver_data; 631 struct digi_port *priv = usb_get_serial_port_data(port); 632 633 spin_lock_irqsave(&priv->dp_port_lock, flags); 634 635 /* restart read chain */ 636 if (priv->dp_throttle_restart) 637 ret = usb_submit_urb(port->read_urb, GFP_ATOMIC); 638 639 /* turn throttle off */ 640 priv->dp_throttled = 0; 641 priv->dp_throttle_restart = 0; 642 643 spin_unlock_irqrestore(&priv->dp_port_lock, flags); 644 645 if (ret) 646 dev_err(&port->dev, 647 "%s: usb_submit_urb failed, ret=%d, port=%d\n", 648 __func__, ret, priv->dp_port_num); 649 } 650 651 652 static void digi_set_termios(struct tty_struct *tty, 653 struct usb_serial_port *port, 654 const struct ktermios *old_termios) 655 { 656 struct digi_port *priv = usb_get_serial_port_data(port); 657 struct device *dev = &port->dev; 658 unsigned int iflag = tty->termios.c_iflag; 659 unsigned int cflag = tty->termios.c_cflag; 660 unsigned int old_iflag = old_termios->c_iflag; 661 unsigned int old_cflag = old_termios->c_cflag; 662 unsigned char buf[32]; 663 unsigned int modem_signals; 664 int arg, ret; 665 int i = 0; 666 speed_t baud; 667 668 dev_dbg(dev, 669 "digi_set_termios: TOP: port=%d, iflag=0x%x, old_iflag=0x%x, cflag=0x%x, old_cflag=0x%x\n", 670 priv->dp_port_num, iflag, old_iflag, cflag, old_cflag); 671 672 /* set baud rate */ 673 baud = tty_get_baud_rate(tty); 674 if (baud != tty_termios_baud_rate(old_termios)) { 675 arg = -1; 676 677 /* reassert DTR and (maybe) RTS on transition from B0 */ 678 if ((old_cflag & CBAUD) == B0) { 679 /* don't set RTS if using hardware flow control */ 680 /* and throttling input */ 681 modem_signals = TIOCM_DTR; 682 if (!C_CRTSCTS(tty) || !tty_throttled(tty)) 683 modem_signals |= TIOCM_RTS; 684 digi_set_modem_signals(port, modem_signals, 1); 685 } 686 switch (baud) { 687 /* drop DTR and RTS on transition to B0 */ 688 case 0: digi_set_modem_signals(port, 0, 1); break; 689 case 50: arg = DIGI_BAUD_50; break; 690 case 75: arg = DIGI_BAUD_75; break; 691 case 110: arg = DIGI_BAUD_110; break; 692 case 150: arg = DIGI_BAUD_150; break; 693 case 200: arg = DIGI_BAUD_200; break; 694 case 300: arg = DIGI_BAUD_300; break; 695 case 600: arg = DIGI_BAUD_600; break; 696 case 1200: arg = DIGI_BAUD_1200; break; 697 case 1800: arg = DIGI_BAUD_1800; break; 698 case 2400: arg = DIGI_BAUD_2400; break; 699 case 4800: arg = DIGI_BAUD_4800; break; 700 case 9600: arg = DIGI_BAUD_9600; break; 701 case 19200: arg = DIGI_BAUD_19200; break; 702 case 38400: arg = DIGI_BAUD_38400; break; 703 case 57600: arg = DIGI_BAUD_57600; break; 704 case 115200: arg = DIGI_BAUD_115200; break; 705 case 230400: arg = DIGI_BAUD_230400; break; 706 case 460800: arg = DIGI_BAUD_460800; break; 707 default: 708 arg = DIGI_BAUD_9600; 709 baud = 9600; 710 break; 711 } 712 if (arg != -1) { 713 buf[i++] = DIGI_CMD_SET_BAUD_RATE; 714 buf[i++] = priv->dp_port_num; 715 buf[i++] = arg; 716 buf[i++] = 0; 717 } 718 } 719 /* set parity */ 720 tty->termios.c_cflag &= ~CMSPAR; 721 722 if ((cflag & (PARENB | PARODD)) != (old_cflag & (PARENB | PARODD))) { 723 if (cflag & PARENB) { 724 if (cflag & PARODD) 725 arg = DIGI_PARITY_ODD; 726 else 727 arg = DIGI_PARITY_EVEN; 728 } else { 729 arg = DIGI_PARITY_NONE; 730 } 731 buf[i++] = DIGI_CMD_SET_PARITY; 732 buf[i++] = priv->dp_port_num; 733 buf[i++] = arg; 734 buf[i++] = 0; 735 } 736 /* set word size */ 737 if ((cflag & CSIZE) != (old_cflag & CSIZE)) { 738 arg = -1; 739 switch (cflag & CSIZE) { 740 case CS5: arg = DIGI_WORD_SIZE_5; break; 741 case CS6: arg = DIGI_WORD_SIZE_6; break; 742 case CS7: arg = DIGI_WORD_SIZE_7; break; 743 case CS8: arg = DIGI_WORD_SIZE_8; break; 744 default: 745 dev_dbg(dev, 746 "digi_set_termios: can't handle word size %d\n", 747 cflag & CSIZE); 748 break; 749 } 750 751 if (arg != -1) { 752 buf[i++] = DIGI_CMD_SET_WORD_SIZE; 753 buf[i++] = priv->dp_port_num; 754 buf[i++] = arg; 755 buf[i++] = 0; 756 } 757 758 } 759 760 /* set stop bits */ 761 if ((cflag & CSTOPB) != (old_cflag & CSTOPB)) { 762 763 if ((cflag & CSTOPB)) 764 arg = DIGI_STOP_BITS_2; 765 else 766 arg = DIGI_STOP_BITS_1; 767 768 buf[i++] = DIGI_CMD_SET_STOP_BITS; 769 buf[i++] = priv->dp_port_num; 770 buf[i++] = arg; 771 buf[i++] = 0; 772 773 } 774 775 /* set input flow control */ 776 if ((iflag & IXOFF) != (old_iflag & IXOFF) || 777 (cflag & CRTSCTS) != (old_cflag & CRTSCTS)) { 778 arg = 0; 779 if (iflag & IXOFF) 780 arg |= DIGI_INPUT_FLOW_CONTROL_XON_XOFF; 781 else 782 arg &= ~DIGI_INPUT_FLOW_CONTROL_XON_XOFF; 783 784 if (cflag & CRTSCTS) { 785 arg |= DIGI_INPUT_FLOW_CONTROL_RTS; 786 787 /* On USB-4 it is necessary to assert RTS prior */ 788 /* to selecting RTS input flow control. */ 789 buf[i++] = DIGI_CMD_SET_RTS_SIGNAL; 790 buf[i++] = priv->dp_port_num; 791 buf[i++] = DIGI_RTS_ACTIVE; 792 buf[i++] = 0; 793 794 } else { 795 arg &= ~DIGI_INPUT_FLOW_CONTROL_RTS; 796 } 797 buf[i++] = DIGI_CMD_SET_INPUT_FLOW_CONTROL; 798 buf[i++] = priv->dp_port_num; 799 buf[i++] = arg; 800 buf[i++] = 0; 801 } 802 803 /* set output flow control */ 804 if ((iflag & IXON) != (old_iflag & IXON) || 805 (cflag & CRTSCTS) != (old_cflag & CRTSCTS)) { 806 arg = 0; 807 if (iflag & IXON) 808 arg |= DIGI_OUTPUT_FLOW_CONTROL_XON_XOFF; 809 else 810 arg &= ~DIGI_OUTPUT_FLOW_CONTROL_XON_XOFF; 811 812 if (cflag & CRTSCTS) 813 arg |= DIGI_OUTPUT_FLOW_CONTROL_CTS; 814 else 815 arg &= ~DIGI_OUTPUT_FLOW_CONTROL_CTS; 816 817 buf[i++] = DIGI_CMD_SET_OUTPUT_FLOW_CONTROL; 818 buf[i++] = priv->dp_port_num; 819 buf[i++] = arg; 820 buf[i++] = 0; 821 } 822 823 /* set receive enable/disable */ 824 if ((cflag & CREAD) != (old_cflag & CREAD)) { 825 if (cflag & CREAD) 826 arg = DIGI_ENABLE; 827 else 828 arg = DIGI_DISABLE; 829 830 buf[i++] = DIGI_CMD_RECEIVE_ENABLE; 831 buf[i++] = priv->dp_port_num; 832 buf[i++] = arg; 833 buf[i++] = 0; 834 } 835 ret = digi_write_oob_command(port, buf, i, 1); 836 if (ret != 0) 837 dev_dbg(dev, "digi_set_termios: write oob failed, ret=%d\n", ret); 838 tty_encode_baud_rate(tty, baud, baud); 839 } 840 841 842 static int digi_break_ctl(struct tty_struct *tty, int break_state) 843 { 844 struct usb_serial_port *port = tty->driver_data; 845 unsigned char buf[4]; 846 847 buf[0] = DIGI_CMD_BREAK_CONTROL; 848 buf[1] = 2; /* length */ 849 buf[2] = break_state ? 1 : 0; 850 buf[3] = 0; /* pad */ 851 852 return digi_write_inb_command(port, buf, 4, 0); 853 } 854 855 856 static int digi_tiocmget(struct tty_struct *tty) 857 { 858 struct usb_serial_port *port = tty->driver_data; 859 struct digi_port *priv = usb_get_serial_port_data(port); 860 unsigned int val; 861 unsigned long flags; 862 863 spin_lock_irqsave(&priv->dp_port_lock, flags); 864 val = priv->dp_modem_signals; 865 spin_unlock_irqrestore(&priv->dp_port_lock, flags); 866 return val; 867 } 868 869 870 static int digi_tiocmset(struct tty_struct *tty, 871 unsigned int set, unsigned int clear) 872 { 873 struct usb_serial_port *port = tty->driver_data; 874 struct digi_port *priv = usb_get_serial_port_data(port); 875 unsigned int val; 876 unsigned long flags; 877 878 spin_lock_irqsave(&priv->dp_port_lock, flags); 879 val = (priv->dp_modem_signals & ~clear) | set; 880 spin_unlock_irqrestore(&priv->dp_port_lock, flags); 881 return digi_set_modem_signals(port, val, 1); 882 } 883 884 885 static int digi_write(struct tty_struct *tty, struct usb_serial_port *port, 886 const unsigned char *buf, int count) 887 { 888 889 int ret, data_len, new_len; 890 struct digi_port *priv = usb_get_serial_port_data(port); 891 unsigned char *data = port->write_urb->transfer_buffer; 892 unsigned long flags; 893 894 dev_dbg(&port->dev, "digi_write: TOP: port=%d, count=%d\n", 895 priv->dp_port_num, count); 896 897 /* copy user data (which can sleep) before getting spin lock */ 898 count = min(count, port->bulk_out_size-2); 899 count = min(64, count); 900 901 /* be sure only one write proceeds at a time */ 902 /* there are races on the port private buffer */ 903 spin_lock_irqsave(&priv->dp_port_lock, flags); 904 905 /* wait for urb status clear to submit another urb */ 906 if (priv->dp_write_urb_in_use) { 907 /* buffer data if count is 1 (probably put_char) if possible */ 908 if (count == 1 && priv->dp_out_buf_len < DIGI_OUT_BUF_SIZE) { 909 priv->dp_out_buf[priv->dp_out_buf_len++] = *buf; 910 new_len = 1; 911 } else { 912 new_len = 0; 913 } 914 spin_unlock_irqrestore(&priv->dp_port_lock, flags); 915 return new_len; 916 } 917 918 /* allow space for any buffered data and for new data, up to */ 919 /* transfer buffer size - 2 (for command and length bytes) */ 920 new_len = min(count, port->bulk_out_size-2-priv->dp_out_buf_len); 921 data_len = new_len + priv->dp_out_buf_len; 922 923 if (data_len == 0) { 924 spin_unlock_irqrestore(&priv->dp_port_lock, flags); 925 return 0; 926 } 927 928 port->write_urb->transfer_buffer_length = data_len+2; 929 930 *data++ = DIGI_CMD_SEND_DATA; 931 *data++ = data_len; 932 933 /* copy in buffered data first */ 934 memcpy(data, priv->dp_out_buf, priv->dp_out_buf_len); 935 data += priv->dp_out_buf_len; 936 937 /* copy in new data */ 938 memcpy(data, buf, new_len); 939 940 ret = usb_submit_urb(port->write_urb, GFP_ATOMIC); 941 if (ret == 0) { 942 priv->dp_write_urb_in_use = 1; 943 ret = new_len; 944 priv->dp_out_buf_len = 0; 945 } 946 947 /* return length of new data written, or error */ 948 spin_unlock_irqrestore(&priv->dp_port_lock, flags); 949 if (ret < 0) 950 dev_err_console(port, 951 "%s: usb_submit_urb failed, ret=%d, port=%d\n", 952 __func__, ret, priv->dp_port_num); 953 dev_dbg(&port->dev, "digi_write: returning %d\n", ret); 954 return ret; 955 956 } 957 958 static void digi_write_bulk_callback(struct urb *urb) 959 { 960 961 struct usb_serial_port *port = urb->context; 962 struct usb_serial *serial; 963 struct digi_port *priv; 964 struct digi_serial *serial_priv; 965 unsigned long flags; 966 int ret = 0; 967 int status = urb->status; 968 bool wakeup; 969 970 /* port and serial sanity check */ 971 if (port == NULL || (priv = usb_get_serial_port_data(port)) == NULL) { 972 pr_err("%s: port or port->private is NULL, status=%d\n", 973 __func__, status); 974 return; 975 } 976 serial = port->serial; 977 if (serial == NULL || (serial_priv = usb_get_serial_data(serial)) == NULL) { 978 dev_err(&port->dev, 979 "%s: serial or serial->private is NULL, status=%d\n", 980 __func__, status); 981 return; 982 } 983 984 /* handle oob callback */ 985 if (priv->dp_port_num == serial_priv->ds_oob_port_num) { 986 dev_dbg(&port->dev, "digi_write_bulk_callback: oob callback\n"); 987 spin_lock_irqsave(&priv->dp_port_lock, flags); 988 priv->dp_write_urb_in_use = 0; 989 wake_up_interruptible(&priv->write_wait); 990 spin_unlock_irqrestore(&priv->dp_port_lock, flags); 991 return; 992 } 993 994 /* try to send any buffered data on this port */ 995 wakeup = true; 996 spin_lock_irqsave(&priv->dp_port_lock, flags); 997 priv->dp_write_urb_in_use = 0; 998 if (priv->dp_out_buf_len > 0) { 999 *((unsigned char *)(port->write_urb->transfer_buffer)) 1000 = (unsigned char)DIGI_CMD_SEND_DATA; 1001 *((unsigned char *)(port->write_urb->transfer_buffer) + 1) 1002 = (unsigned char)priv->dp_out_buf_len; 1003 port->write_urb->transfer_buffer_length = 1004 priv->dp_out_buf_len + 2; 1005 memcpy(port->write_urb->transfer_buffer + 2, priv->dp_out_buf, 1006 priv->dp_out_buf_len); 1007 ret = usb_submit_urb(port->write_urb, GFP_ATOMIC); 1008 if (ret == 0) { 1009 priv->dp_write_urb_in_use = 1; 1010 priv->dp_out_buf_len = 0; 1011 wakeup = false; 1012 } 1013 } 1014 spin_unlock_irqrestore(&priv->dp_port_lock, flags); 1015 1016 if (ret && ret != -EPERM) 1017 dev_err_console(port, 1018 "%s: usb_submit_urb failed, ret=%d, port=%d\n", 1019 __func__, ret, priv->dp_port_num); 1020 1021 if (wakeup) 1022 tty_port_tty_wakeup(&port->port); 1023 } 1024 1025 static unsigned int digi_write_room(struct tty_struct *tty) 1026 { 1027 struct usb_serial_port *port = tty->driver_data; 1028 struct digi_port *priv = usb_get_serial_port_data(port); 1029 unsigned long flags; 1030 unsigned int room; 1031 1032 spin_lock_irqsave(&priv->dp_port_lock, flags); 1033 1034 if (priv->dp_write_urb_in_use) 1035 room = 0; 1036 else 1037 room = port->bulk_out_size - 2 - priv->dp_out_buf_len; 1038 1039 spin_unlock_irqrestore(&priv->dp_port_lock, flags); 1040 dev_dbg(&port->dev, "digi_write_room: port=%d, room=%u\n", priv->dp_port_num, room); 1041 return room; 1042 1043 } 1044 1045 static unsigned int digi_chars_in_buffer(struct tty_struct *tty) 1046 { 1047 struct usb_serial_port *port = tty->driver_data; 1048 struct digi_port *priv = usb_get_serial_port_data(port); 1049 unsigned long flags; 1050 unsigned int chars; 1051 1052 spin_lock_irqsave(&priv->dp_port_lock, flags); 1053 if (priv->dp_write_urb_in_use) 1054 chars = port->bulk_out_size - 2; 1055 else 1056 chars = priv->dp_out_buf_len; 1057 spin_unlock_irqrestore(&priv->dp_port_lock, flags); 1058 1059 dev_dbg(&port->dev, "%s: port=%d, chars=%d\n", __func__, 1060 priv->dp_port_num, chars); 1061 return chars; 1062 } 1063 1064 static void digi_dtr_rts(struct usb_serial_port *port, int on) 1065 { 1066 /* Adjust DTR and RTS */ 1067 digi_set_modem_signals(port, on * (TIOCM_DTR | TIOCM_RTS), 1); 1068 } 1069 1070 static int digi_open(struct tty_struct *tty, struct usb_serial_port *port) 1071 { 1072 int ret; 1073 unsigned char buf[32]; 1074 struct digi_port *priv = usb_get_serial_port_data(port); 1075 struct ktermios not_termios; 1076 1077 /* be sure the device is started up */ 1078 if (digi_startup_device(port->serial) != 0) 1079 return -ENXIO; 1080 1081 /* read modem signals automatically whenever they change */ 1082 buf[0] = DIGI_CMD_READ_INPUT_SIGNALS; 1083 buf[1] = priv->dp_port_num; 1084 buf[2] = DIGI_ENABLE; 1085 buf[3] = 0; 1086 1087 /* flush fifos */ 1088 buf[4] = DIGI_CMD_IFLUSH_FIFO; 1089 buf[5] = priv->dp_port_num; 1090 buf[6] = DIGI_FLUSH_TX | DIGI_FLUSH_RX; 1091 buf[7] = 0; 1092 1093 ret = digi_write_oob_command(port, buf, 8, 1); 1094 if (ret != 0) 1095 dev_dbg(&port->dev, "digi_open: write oob failed, ret=%d\n", ret); 1096 1097 /* set termios settings */ 1098 if (tty) { 1099 not_termios.c_cflag = ~tty->termios.c_cflag; 1100 not_termios.c_iflag = ~tty->termios.c_iflag; 1101 digi_set_termios(tty, port, ¬_termios); 1102 } 1103 return 0; 1104 } 1105 1106 1107 static void digi_close(struct usb_serial_port *port) 1108 { 1109 DEFINE_WAIT(wait); 1110 int ret; 1111 unsigned char buf[32]; 1112 struct digi_port *priv = usb_get_serial_port_data(port); 1113 1114 mutex_lock(&port->serial->disc_mutex); 1115 /* if disconnected, just clear flags */ 1116 if (port->serial->disconnected) 1117 goto exit; 1118 1119 /* FIXME: Transmit idle belongs in the wait_unti_sent path */ 1120 digi_transmit_idle(port, DIGI_CLOSE_TIMEOUT); 1121 1122 /* disable input flow control */ 1123 buf[0] = DIGI_CMD_SET_INPUT_FLOW_CONTROL; 1124 buf[1] = priv->dp_port_num; 1125 buf[2] = DIGI_DISABLE; 1126 buf[3] = 0; 1127 1128 /* disable output flow control */ 1129 buf[4] = DIGI_CMD_SET_OUTPUT_FLOW_CONTROL; 1130 buf[5] = priv->dp_port_num; 1131 buf[6] = DIGI_DISABLE; 1132 buf[7] = 0; 1133 1134 /* disable reading modem signals automatically */ 1135 buf[8] = DIGI_CMD_READ_INPUT_SIGNALS; 1136 buf[9] = priv->dp_port_num; 1137 buf[10] = DIGI_DISABLE; 1138 buf[11] = 0; 1139 1140 /* disable receive */ 1141 buf[12] = DIGI_CMD_RECEIVE_ENABLE; 1142 buf[13] = priv->dp_port_num; 1143 buf[14] = DIGI_DISABLE; 1144 buf[15] = 0; 1145 1146 /* flush fifos */ 1147 buf[16] = DIGI_CMD_IFLUSH_FIFO; 1148 buf[17] = priv->dp_port_num; 1149 buf[18] = DIGI_FLUSH_TX | DIGI_FLUSH_RX; 1150 buf[19] = 0; 1151 1152 ret = digi_write_oob_command(port, buf, 20, 0); 1153 if (ret != 0) 1154 dev_dbg(&port->dev, "digi_close: write oob failed, ret=%d\n", 1155 ret); 1156 /* wait for final commands on oob port to complete */ 1157 prepare_to_wait(&priv->dp_flush_wait, &wait, 1158 TASK_INTERRUPTIBLE); 1159 schedule_timeout(DIGI_CLOSE_TIMEOUT); 1160 finish_wait(&priv->dp_flush_wait, &wait); 1161 1162 /* shutdown any outstanding bulk writes */ 1163 usb_kill_urb(port->write_urb); 1164 exit: 1165 spin_lock_irq(&priv->dp_port_lock); 1166 priv->dp_write_urb_in_use = 0; 1167 wake_up_interruptible(&priv->dp_close_wait); 1168 spin_unlock_irq(&priv->dp_port_lock); 1169 mutex_unlock(&port->serial->disc_mutex); 1170 } 1171 1172 1173 /* 1174 * Digi Startup Device 1175 * 1176 * Starts reads on all ports. Must be called AFTER startup, with 1177 * urbs initialized. Returns 0 if successful, non-zero error otherwise. 1178 */ 1179 1180 static int digi_startup_device(struct usb_serial *serial) 1181 { 1182 int i, ret = 0; 1183 struct digi_serial *serial_priv = usb_get_serial_data(serial); 1184 struct usb_serial_port *port; 1185 1186 /* be sure this happens exactly once */ 1187 spin_lock(&serial_priv->ds_serial_lock); 1188 if (serial_priv->ds_device_started) { 1189 spin_unlock(&serial_priv->ds_serial_lock); 1190 return 0; 1191 } 1192 serial_priv->ds_device_started = 1; 1193 spin_unlock(&serial_priv->ds_serial_lock); 1194 1195 /* start reading from each bulk in endpoint for the device */ 1196 /* set USB_DISABLE_SPD flag for write bulk urbs */ 1197 for (i = 0; i < serial->type->num_ports + 1; i++) { 1198 port = serial->port[i]; 1199 ret = usb_submit_urb(port->read_urb, GFP_KERNEL); 1200 if (ret != 0) { 1201 dev_err(&port->dev, 1202 "%s: usb_submit_urb failed, ret=%d, port=%d\n", 1203 __func__, ret, i); 1204 break; 1205 } 1206 } 1207 return ret; 1208 } 1209 1210 static int digi_port_init(struct usb_serial_port *port, unsigned port_num) 1211 { 1212 struct digi_port *priv; 1213 1214 priv = kzalloc(sizeof(*priv), GFP_KERNEL); 1215 if (!priv) 1216 return -ENOMEM; 1217 1218 spin_lock_init(&priv->dp_port_lock); 1219 priv->dp_port_num = port_num; 1220 init_waitqueue_head(&priv->dp_transmit_idle_wait); 1221 init_waitqueue_head(&priv->dp_flush_wait); 1222 init_waitqueue_head(&priv->dp_close_wait); 1223 init_waitqueue_head(&priv->write_wait); 1224 priv->dp_port = port; 1225 1226 usb_set_serial_port_data(port, priv); 1227 1228 return 0; 1229 } 1230 1231 static int digi_startup(struct usb_serial *serial) 1232 { 1233 struct digi_serial *serial_priv; 1234 int ret; 1235 1236 serial_priv = kzalloc(sizeof(*serial_priv), GFP_KERNEL); 1237 if (!serial_priv) 1238 return -ENOMEM; 1239 1240 spin_lock_init(&serial_priv->ds_serial_lock); 1241 serial_priv->ds_oob_port_num = serial->type->num_ports; 1242 serial_priv->ds_oob_port = serial->port[serial_priv->ds_oob_port_num]; 1243 1244 ret = digi_port_init(serial_priv->ds_oob_port, 1245 serial_priv->ds_oob_port_num); 1246 if (ret) { 1247 kfree(serial_priv); 1248 return ret; 1249 } 1250 1251 usb_set_serial_data(serial, serial_priv); 1252 1253 return 0; 1254 } 1255 1256 1257 static void digi_disconnect(struct usb_serial *serial) 1258 { 1259 int i; 1260 1261 /* stop reads and writes on all ports */ 1262 for (i = 0; i < serial->type->num_ports + 1; i++) { 1263 usb_kill_urb(serial->port[i]->read_urb); 1264 usb_kill_urb(serial->port[i]->write_urb); 1265 } 1266 } 1267 1268 1269 static void digi_release(struct usb_serial *serial) 1270 { 1271 struct digi_serial *serial_priv; 1272 struct digi_port *priv; 1273 1274 serial_priv = usb_get_serial_data(serial); 1275 1276 priv = usb_get_serial_port_data(serial_priv->ds_oob_port); 1277 kfree(priv); 1278 1279 kfree(serial_priv); 1280 } 1281 1282 static int digi_port_probe(struct usb_serial_port *port) 1283 { 1284 return digi_port_init(port, port->port_number); 1285 } 1286 1287 static void digi_port_remove(struct usb_serial_port *port) 1288 { 1289 struct digi_port *priv; 1290 1291 priv = usb_get_serial_port_data(port); 1292 kfree(priv); 1293 } 1294 1295 static void digi_read_bulk_callback(struct urb *urb) 1296 { 1297 struct usb_serial_port *port = urb->context; 1298 struct digi_port *priv; 1299 struct digi_serial *serial_priv; 1300 int ret; 1301 int status = urb->status; 1302 1303 /* port sanity check, do not resubmit if port is not valid */ 1304 if (port == NULL) 1305 return; 1306 priv = usb_get_serial_port_data(port); 1307 if (priv == NULL) { 1308 dev_err(&port->dev, "%s: port->private is NULL, status=%d\n", 1309 __func__, status); 1310 return; 1311 } 1312 if (port->serial == NULL || 1313 (serial_priv = usb_get_serial_data(port->serial)) == NULL) { 1314 dev_err(&port->dev, "%s: serial is bad or serial->private " 1315 "is NULL, status=%d\n", __func__, status); 1316 return; 1317 } 1318 1319 /* do not resubmit urb if it has any status error */ 1320 if (status) { 1321 dev_err(&port->dev, 1322 "%s: nonzero read bulk status: status=%d, port=%d\n", 1323 __func__, status, priv->dp_port_num); 1324 return; 1325 } 1326 1327 /* handle oob or inb callback, do not resubmit if error */ 1328 if (priv->dp_port_num == serial_priv->ds_oob_port_num) { 1329 if (digi_read_oob_callback(urb) != 0) 1330 return; 1331 } else { 1332 if (digi_read_inb_callback(urb) != 0) 1333 return; 1334 } 1335 1336 /* continue read */ 1337 ret = usb_submit_urb(urb, GFP_ATOMIC); 1338 if (ret != 0 && ret != -EPERM) { 1339 dev_err(&port->dev, 1340 "%s: failed resubmitting urb, ret=%d, port=%d\n", 1341 __func__, ret, priv->dp_port_num); 1342 } 1343 1344 } 1345 1346 /* 1347 * Digi Read INB Callback 1348 * 1349 * Digi Read INB Callback handles reads on the in band ports, sending 1350 * the data on to the tty subsystem. When called we know port and 1351 * port->private are not NULL and port->serial has been validated. 1352 * It returns 0 if successful, 1 if successful but the port is 1353 * throttled, and -1 if the sanity checks failed. 1354 */ 1355 1356 static int digi_read_inb_callback(struct urb *urb) 1357 { 1358 struct usb_serial_port *port = urb->context; 1359 struct digi_port *priv = usb_get_serial_port_data(port); 1360 unsigned char *buf = urb->transfer_buffer; 1361 unsigned long flags; 1362 int opcode; 1363 int len; 1364 int port_status; 1365 unsigned char *data; 1366 int tty_flag, throttled; 1367 1368 /* short/multiple packet check */ 1369 if (urb->actual_length < 2) { 1370 dev_warn(&port->dev, "short packet received\n"); 1371 return -1; 1372 } 1373 1374 opcode = buf[0]; 1375 len = buf[1]; 1376 1377 if (urb->actual_length != len + 2) { 1378 dev_err(&port->dev, "malformed packet received: port=%d, opcode=%d, len=%d, actual_length=%u\n", 1379 priv->dp_port_num, opcode, len, urb->actual_length); 1380 return -1; 1381 } 1382 1383 if (opcode == DIGI_CMD_RECEIVE_DATA && len < 1) { 1384 dev_err(&port->dev, "malformed data packet received\n"); 1385 return -1; 1386 } 1387 1388 spin_lock_irqsave(&priv->dp_port_lock, flags); 1389 1390 /* check for throttle; if set, do not resubmit read urb */ 1391 /* indicate the read chain needs to be restarted on unthrottle */ 1392 throttled = priv->dp_throttled; 1393 if (throttled) 1394 priv->dp_throttle_restart = 1; 1395 1396 /* receive data */ 1397 if (opcode == DIGI_CMD_RECEIVE_DATA) { 1398 port_status = buf[2]; 1399 data = &buf[3]; 1400 1401 /* get flag from port_status */ 1402 tty_flag = 0; 1403 1404 /* overrun is special, not associated with a char */ 1405 if (port_status & DIGI_OVERRUN_ERROR) 1406 tty_insert_flip_char(&port->port, 0, TTY_OVERRUN); 1407 1408 /* break takes precedence over parity, */ 1409 /* which takes precedence over framing errors */ 1410 if (port_status & DIGI_BREAK_ERROR) 1411 tty_flag = TTY_BREAK; 1412 else if (port_status & DIGI_PARITY_ERROR) 1413 tty_flag = TTY_PARITY; 1414 else if (port_status & DIGI_FRAMING_ERROR) 1415 tty_flag = TTY_FRAME; 1416 1417 /* data length is len-1 (one byte of len is port_status) */ 1418 --len; 1419 if (len > 0) { 1420 tty_insert_flip_string_fixed_flag(&port->port, data, 1421 tty_flag, len); 1422 tty_flip_buffer_push(&port->port); 1423 } 1424 } 1425 spin_unlock_irqrestore(&priv->dp_port_lock, flags); 1426 1427 if (opcode == DIGI_CMD_RECEIVE_DISABLE) 1428 dev_dbg(&port->dev, "%s: got RECEIVE_DISABLE\n", __func__); 1429 else if (opcode != DIGI_CMD_RECEIVE_DATA) 1430 dev_dbg(&port->dev, "%s: unknown opcode: %d\n", __func__, opcode); 1431 1432 return throttled ? 1 : 0; 1433 1434 } 1435 1436 1437 /* 1438 * Digi Read OOB Callback 1439 * 1440 * Digi Read OOB Callback handles reads on the out of band port. 1441 * When called we know port and port->private are not NULL and 1442 * the port->serial is valid. It returns 0 if successful, and 1443 * -1 if the sanity checks failed. 1444 */ 1445 1446 static int digi_read_oob_callback(struct urb *urb) 1447 { 1448 1449 struct usb_serial_port *port = urb->context; 1450 struct usb_serial *serial = port->serial; 1451 struct tty_struct *tty; 1452 struct digi_port *priv; 1453 unsigned char *buf = urb->transfer_buffer; 1454 int opcode, line, status, val; 1455 unsigned long flags; 1456 int i; 1457 unsigned int rts; 1458 1459 if (urb->actual_length < 4) 1460 return -1; 1461 1462 /* handle each oob command */ 1463 for (i = 0; i < urb->actual_length - 3; i += 4) { 1464 opcode = buf[i]; 1465 line = buf[i + 1]; 1466 status = buf[i + 2]; 1467 val = buf[i + 3]; 1468 1469 dev_dbg(&port->dev, "digi_read_oob_callback: opcode=%d, line=%d, status=%d, val=%d\n", 1470 opcode, line, status, val); 1471 1472 if (status != 0 || line >= serial->type->num_ports) 1473 continue; 1474 1475 port = serial->port[line]; 1476 1477 priv = usb_get_serial_port_data(port); 1478 if (priv == NULL) 1479 return -1; 1480 1481 tty = tty_port_tty_get(&port->port); 1482 1483 rts = 0; 1484 if (tty) 1485 rts = C_CRTSCTS(tty); 1486 1487 if (tty && opcode == DIGI_CMD_READ_INPUT_SIGNALS) { 1488 bool wakeup = false; 1489 1490 spin_lock_irqsave(&priv->dp_port_lock, flags); 1491 /* convert from digi flags to termiox flags */ 1492 if (val & DIGI_READ_INPUT_SIGNALS_CTS) { 1493 priv->dp_modem_signals |= TIOCM_CTS; 1494 if (rts) 1495 wakeup = true; 1496 } else { 1497 priv->dp_modem_signals &= ~TIOCM_CTS; 1498 /* port must be open to use tty struct */ 1499 } 1500 if (val & DIGI_READ_INPUT_SIGNALS_DSR) 1501 priv->dp_modem_signals |= TIOCM_DSR; 1502 else 1503 priv->dp_modem_signals &= ~TIOCM_DSR; 1504 if (val & DIGI_READ_INPUT_SIGNALS_RI) 1505 priv->dp_modem_signals |= TIOCM_RI; 1506 else 1507 priv->dp_modem_signals &= ~TIOCM_RI; 1508 if (val & DIGI_READ_INPUT_SIGNALS_DCD) 1509 priv->dp_modem_signals |= TIOCM_CD; 1510 else 1511 priv->dp_modem_signals &= ~TIOCM_CD; 1512 1513 spin_unlock_irqrestore(&priv->dp_port_lock, flags); 1514 1515 if (wakeup) 1516 tty_port_tty_wakeup(&port->port); 1517 } else if (opcode == DIGI_CMD_TRANSMIT_IDLE) { 1518 spin_lock_irqsave(&priv->dp_port_lock, flags); 1519 priv->dp_transmit_idle = 1; 1520 wake_up_interruptible(&priv->dp_transmit_idle_wait); 1521 spin_unlock_irqrestore(&priv->dp_port_lock, flags); 1522 } else if (opcode == DIGI_CMD_IFLUSH_FIFO) { 1523 wake_up_interruptible(&priv->dp_flush_wait); 1524 } 1525 tty_kref_put(tty); 1526 } 1527 return 0; 1528 1529 } 1530 1531 module_usb_serial_driver(serial_drivers, id_table_combined); 1532 1533 MODULE_AUTHOR(DRIVER_AUTHOR); 1534 MODULE_DESCRIPTION(DRIVER_DESC); 1535 MODULE_LICENSE("GPL"); 1536